Locale gets lost in itemEditor
My app need only use the en-US locale.
Because numbers like 1,000.00 were being displayed as 1 000,00 in spark Formatters and components, I figured out that it is necessary to declare this for the application in a css declaration.
This works fine until I work with numbers in a datagrid itemEditor. The locale declaration is defaulting back to 1 000,00 formatting.
I assume that the application-wide declaration is ignored somehow. Am I missing something?
If you have a simple test case, file a bug at bugs.adobe.com/jira
Similar Messages
-
Anchor mobility configuration getting lost in wlc 5508 ios code 7.4.100.0
It is observed that in WLC 5508 , ios 7.4.100.0 , mobility anchor configuration on wlan is getting lost . we configure anchor ip address on guest wlan > mobility anchor > Switch IP Address (Anchor).
We have configured the template on NCS 2.0 to push the anchor mobility ip address on all WLC
Has anyone oberved this behavoiur. We have more than 100 WLC , and everyweek mobility anchor configuration is lost on some WLC having code 7.4.100.0.I am having this exact same problem. I am running 7.3 on 5508 WLC. My remote site LAP's are using Flex (HREAP). The initial access point that my laptop associates to connects with no problem, as soon as I wander out of range of the initial LAP and into the area of another access point, I lose data connectivity. The was validated like the original post as I start a constant ping on the LAN and watch as the ping latency increases and then ping replies stop. The only way to correct the problem is resetting of the wireless adapter on the laptop. Side note my DroidX has no problem wandering from AP to AP.
Laptop: Windows 7 32bit
I then returned to my home site and test where I have a secondary controller and the LAP's are configured for local mode, no problems roaming from access point to access point. Validated with constant ping test. The pings drop for a second and re-
continues as the laptop reconnects.
**Edit: I am going to try the removing the DHCP Addr. Assignment required option, and report that back to the TAC engineer.
Message was edited by: Michael Dunki-Jacobs
**Edit Solved:***
The problem is in deed solved by turning the "DHCP Address Required" but why? -
Group Folder -- Permissions Get Lost/Denied
We have a small LAN with a single group folder on an AFP network mount. The protocol is set to "inherent permissions" and I've promulgated this to the folder at least once. The owner is "admin" and the group is set to the short name of my workgroup. All (including "everyone") have permission to read/write. Every user is in the group. The acl list is empty, and the network mount is set to "use for: user home directories" (the latter because there is no option to select 'use for group folder.'
The folder is set to mount at login. (Users login at login, tho their homes are local.) All works fine, BUT after a while, the permissions to use the folder and its contents gets lost and the user is denied access.
A logout usually restores the right to use the folder, but this is driving me/my users crazy. Any aid much appreciated.i'm seeing something very similar but not with a group folder. my users are constantly loosing their permissions on files within sharepoints that they should have access to. they have to log out of the server and log back in to restore the correct permissions.
is anybody else seeing this? it's becoming a huge problem and happens daily now. -
How do I use the Verizon Service & Protection app to locate my phone if it gets lost?
The Verizon Support & Protection app (VZ Protect) is installed on my phone and is supposed to help me if my phone is lost or stolen by allowing me to find it on a map, lock it, erase my data from it, etc. But I found it nearly impossible to figure out what I should do in the event that actually did get lost or stolen.
I logged into my My Verizon account from my computer (which is probably what I would do if I lost my phone), but unfortunately there isn't anything on the site to help a person who has actually lost their phone or had it stolen to quickly and easily locate it. Most of the links I found were only promoting Verizon's services and the app, but nothing on how to use it.
I tried searching for things I might type if I had actually lost my phone (like, "missing phone", "stolen phone", "find lost phone"). I had to go into the "How to Use Guide: Verizon Support & Protection" page, which I was only able to find on the Verizon Support & Protection FAQs page), in order to find a link that told me I had to go to the Verizon Support & Protection App website to use this service.
There really should be something more obvious right on the My Verizon site.Purchase a replacement remote.
The remote is required for configuring the ATV and setting up the remote app on iDevices. -
How do i fixed my problem with my ipad apps every time i open that apps it takes 10min. to play the games ant its getting LOST MODE and the ipad system is crashing
We are fellow users here on these user-to-user forums, you're not talking to iTunes Support nor Apple.
Have you tried closing all apps via the iPad's multitasking bar and then doing a soft-reset and seeing that helps ? To close all apps :
iOS 7: double-click the home button to open the taskbar, and then swipe or drag each app's screen from there up and off the top of the screen to close it, and click the home button to close the taskbar.
iOS 6 and below : from the home screen (i.e. not with any app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of each app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
Soft-reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot. -
Hyperlinks from other placed indd documents or pdfs getting lost after export to PDF
after upgrade vom CS 5.5 to CS 6: hyperlinks from other placed indd documents or pdfs getting lost after export to PDF
I tried all options for the as well known and working export optionsafter upgrade vom CS 5.5 to CS 6: hyperlinks from other placed indd documents or pdfs getting lost after export to PDF
I tried all options for the as well known and working export options -
I have a problem with my iphone 4. My 3G always stays activated but I lose my network signal. The bars all get lost and I'm not able to receive / send sms, mms or phone calls. Could you guys please help me fix this problem? Ios 5.1.1
I haven't gotten a new sim card because the problem has been presenting itself in various cards not only mine. So far, all I've done is reset my network settings.
Last night, I turned off the 3G tab and it had all the signal bars. Today, I did the network reset and it's working apparently. But like I said before, previously the bars just disappear and the iphone only has the 3G activated. -
I am in Saudi and trying to download navigon middle east. Every time I try to buy the app it will show up, says waiting and disappears. How can I get around it and not get lost on these crazy roads?
I recently purchased a second hand new macbook air, although it was second hand to me the previous owner had never actually turned it on.
Something doesn't make sense here, though I'm not saying the previous owner is lying....
Time to send your serial # to iTS and let them see what's happening here.
iTunes Store Support
http://www.apple.com/emea/support/itunes/contact.html -
'D' Value in UPDMOD field getting lost in Transformation,Delete not working
Hello all,
We are using this datasource 0PU_IS_PS_32 for Funds management, the datasource has UPDMOD field in it, which is basically the 0RECORDMODE. So when they delete the document on R/3 side we can pick up the delete.
Now this is what is happening in the delta infopackage, I get the delat records in the delta infopackage and I see a "D" in the UPDMOD field, but that value of D is getting lost when i load the data from PSA to the DSO through transofrmation by using DTP.
After the request is loaded in DSO, before activating the request I check in New Data table and the field does not have a value of "D" anymore so when I activate the request the system does not know that those records are "D" delete records and so the records are not getting deleted from DSO.
Has anyone faced this before, how can I fix it. The transformation is just one to one mapping no routines or formulas of any kind.
Thanks for your help in advance.Hi,
It is mandatory that u map upmode to 0recordmode. In the rule group there will be 2 groups. One will be ur normal mapping and other should be used to map 0recordmode
Regards,
Raghavendra. -
Now issue related to session
I am using tomcat 3.1
In my login page my session value get lost frequently.I am using session.setAttribute("logon.isDone", name); in servlets and In every jsp's I am checking as <% if(session.getAttribute("logon.isDone")==null){
response.sendRedirect("/iscap/report/relogin.jsp");}%>
The value get lost in a very short time so user is sent to relogin .
Now what I do here?
payal sharmaHi
try to set the maximum interval between requests
eg:
session.setMaxInactiveInterval(6000);
vis -
I have thousands of photos on my Mac. If something happens to my Mac obviously, I don't want to lose the photos. I do Time Machine back ups to an external hard drive once a week. Is this good enough to make sure my pictures don't get lost?
tgs6164 wrote:
I have thousands of photos on my Mac. If something happens to my Mac obviously, I don't want to lose the photos. I do Time Machine back ups to an external hard drive once a week. Is this good enough to make sure my pictures don't get lost?
Purchase a couple of these when they go on sale.
Start burning all the photos onto DVDs.
At least you'll have all your photos if your computer, time machine or any other backup you use goes bonkers. -
We use a replicated partition to copy data from planning to essbase application. Partition works fine and data gets copied. We have another separate maxl script which does changes to the outline. This script exports the data from essbase, clears the database, updates the outline, reimports the exported data and does a cube build. Once this maxl completes, whatever data copied from planning is lost. But if I look at the export file, planning data exist in the export file. We know import process is working fine, because other data not loaded thru partition exist in essbase.. Only data loaded from planning gets lost..
Can someone help me on this issue?Hi Mahe,
1. You maxl does the following things
exports data
clears data
updates the outline
reimports the data
2. After you reimport,Are you trying to retrive to confirm the data ?
3. After you reimport the data, check the properties of database ( check whether the new blocks have been loaded , and increased the count ).
4. Are you exporting all data , or only level 0 ?
5. If its only level 0, You need to aggregate or consolidate ( by running calculation script).
Hope this helps
Sandeep Reddy Enti
HCC
http://hyperionconsultancy.com/ -
Mavericks Cover flow in Finder gets lost
This is a repost from "Lion" category. Fits better here.
"have upgraded to Mavericks, and I am having trouble with Coverflow in the Finder. When I delete files it gets lost, showing previews of files that are not the ones that are highlighted. The spacebar preview seems to work, showing me the actual contents, but the coverflow view is for a different file. Also, if there is a long list of files in the folder, it cannot display the files further down the list.
I was in the middle of a large project, going through thousands of photos in finder, when I upgraded. I had the perfect workflow, using coverflow, and it worked flawlessly in Lion. It seems this got boken in the update."
-crazyBrit
I'm having the same problem. If I navigated away from a folder it was happening with for a while, the ghost perviews in the coverflow would disappear, but it would still happen if I tried to move or delete a file.Several of my applications (adobe acrobat, CAD) often crash (and need to be Forsed Quit) when I try to open a file using Cover Flow. AutoCAD release the following advisory:
AutoCAD crashes or file navigation dialog boxes close unexpectedly in Mac OS X 10.9 (Mavericks)
Issue
AutoCAD crashes or the open dialog boxes close unexpectedly while using Open or other file navigation dialogs in AutoCAD on Mac OS 10.9 (Mavericks).
Solution
This happens when you use Cover Flow view mode in a dialog box and navigate across folders. This issue will need to be corrected by Apple in a future Mavericks update.
To work around this issue, do not use the Cover Flow view mode in file navigation dialog boxes such as Open, New, Save, External Reference attach, PDF attach, Image attach, Import, Export, etc.
This is particularly annoying when trying to select a particular graphic file to work on. I wind up opening a finder window in Cover Flow to find the particular graphic I want to open and then looking for the file name in List View in the Open diaglog box. -
Blank spaces at the end of an IDoc text field get lost when posted to R/3
Hi Guys,
I am facing the following issue:
In an XML file-to-Idoc scenario, there are spaces at the end of a text field in the inbound XML file, which I can see when I open the inbound file with a text editor like notepad, and they are kept after XI mapping is executed (I can see them in message mapping simulator). However, it seems that these spaces get lost once the IDoc is posted to SAP R/3 and they are not visible on SAP R/3 side.
Do you have any idea ? Thanks.
Best Regards,
Evaggelos GkatziosThat means SAP is removing the spaces from IDoc fields, where you spaces are not allowed. Does it create any problem?
Thanks,
Nabendu. -
Parameter of Source-portion of url gets lost
Hi Expert,
following Situation:
Default List-View-WebPart from a custom List added to a Enterprise-Wiki-Page.
First column in the List-View is the edit button to open the related edit-Form.
Because of a custom Edit-Form which is not set as the default for edit i have to relink to my specific Form.
I have done this by this script which is included by Script-Editor-WebPart:
var tags = $('a[onclick*="84858E12"]');
if(tags)
tags.each(function ()
var att = $(this).attr('onclick');
if(att)
if(att.match(/ID=([0-9]*)/))
var id = $(this).attr('onclick').match(/ID=([0-9]*)/)[1];
var bo = $(this).closest('td').next('td').find('a').text();
if(bo)
$(this).removeAttr('onclick');
$(this).attr('href', '/Lists/Leads/LeadEdit.aspx?ID=' + id + "&BO=" + encodeURIComponent(bo));
$(this).attr('onclick', 'GoToLink(this);return false;');
If i click a edit button to open my edit form everything works fine and the URL has correct values. The source Portion works fine if i close the edit form (save or cancel). So far so good.
In last mentioned edit form i have another List-View-WebPart (Added through SharePoint-Designer) which holds data of a related list. Filter is working fine here. For this List-View i also have to relink the edit button to another specific edit form. I have
done this in the same way as i did it before. The important part of the script:
$(this).click(function(e)
e.preventDefault();
var currentid = $(this).attr('href').match(/ID=([0-9]*)/)[1];
var encbo = encodeURIComponent(getBO());
$s = "/Lists/Com2Know/Edit.aspx?ID=" + currentid + "&BO=" + encbo+ "&Source=" + source + "&BO=" + encbo;
location.href = $s;
This also works fine. Source Portion is shown and correct. If i copy the source Portion and paste it to a new browser tab it is working fine. But if i Close this edit form (save or cancel) a Parameter of the source portion of the URL gets lost somehow and
now i'm not there where i wanted to be. The URL is as follows (changed hostheader to ...)
http://.../Lists/Com2Know/Edit.aspx?ID=86&BO=LE%2F2014%2F2000084&Source=http://.../Lists/Leads/LeadEdit.aspx?ID=84&BO=LE%2F2014%2F2000084
So i should go to http://.../Lists/Leads/LeadEdit.aspx?ID=84&BO=LE%2F2014%2F2000084
but i end up here: http://.../Lists/Leads/LeadEdit.aspx?ID=84
So my Parameter BO is missing.
Do i miss something from specification?
With Kind regards,
RonnySorry Folks, i got it myself and i hope it is useful for somebody else.
Just mask the ampersand for Parameters in source Portion with %26
So in my case: source + "%26BO="
Kredits to Marc D Anderson. Thanx!
Ronny
Maybe you are looking for
-
How to hide particular block in selection screen
Hi, I am having different blocks in a selection screen. How to show the blocks dynamically according to a radio button selection. means how to Hide/show entire block. Thanks, anandan
-
Why was my order to replace a faulty Home Hub canc...
Having been told last Thursday by one of BT's technical support team in India that my Home Hub was faulty, I was assured that I would receive a replacement within a couple of days, followed by a phone call between 2 and 3 pm yesterday afternoon to en
-
Bluetooth not working on original iphone after 2.1 update
Just updated my original iphone to 2.1 and all my pairings for bluetooth are gone. Also when I attempt to re-pair the bluetooth section just displays a spinning circle and refuses to recognize any of my bluetooth devices.
-
Hi, I am new or know nothing about Mac Mini which I received from relative as gift along with few software including lion OS. I want to install lion after time machine backup of current files Mac OS X 10.6.8. MY question is that backup of Mac OS X 10
-
How do I get the Norton 360 Toolbar & Identity Safe onto Firefox 4?
I cannot get the Identity Safe feature of Norton 360 onto my Firefox 4 toolbar. I tried configuring Norton 360 as per the FIrefox 4 instructions to no avail. it worked on Firefox 3.