Lock screen display not working properly on wakeup from screen sleep
I just purchased a macbook air top model mid 2012... yesterday. It's brand new. When I click the trackpad to wake up the screen after it sleeps and has auto-locked (not a computer sleep! just a screen sleep), the screen is not all present. I have to move my mouse around to reveal the rest of the screen. Once I have done that enough to find my icon to enable text entry, I put in my password and I get back to the desktop which is then normal. This behaviour is only occuring on a wake-up after screen sleep. Seems like a video driver problem to me. The only add-ons I have at the moment are alfred and bettersnaptool. Has anyone run into this? Is there a fix? Also, I have applied all the latest updates. I can't remember, but this might have begun after the latest update.
Thanks,
John
I believe this article describes the issue:
http://support.apple.com/kb/TS4135
Similar Messages
-
T500 on screen display not working
I searched, but have not found any other posts with this problem.
I re-loaded Windows Vista 64 on a new hard drive, and have re-installed all drivers. I installed the hotkey driver for on screen display, and the tab appears correctly in the advanced display properties.
The on-screen display was working properly with the default Vista driver, but once I installed the dual graphics drivers, the on-screen display has become about 2 pixels high, just above the windows task bar. I tried changing the font and size and color in the setup tab, but this doesn't fix it. I have uninstalled and re-installed the hotkey driver, and also the display drivers.
Any ideas for this strange one?
Solved!
Go to Solution.Thank you! That did it! For others benefit, here are the instructions from the earlier thread:
There is a bug, so the size isn't really set, and you don't see anything. That's why you have to edit the size in windows registry editor. Click Start -> RUN-> type "regedit" BE CAREFULL with this tool! Press CTRL+F .... and find "OnScreenDisplay" Whole path will be: HKEY_CURRENT_USER\Software\IBM\TPHOTKEY\OnScreenDisplay Change "Size" value from "00 00 00 00" to "00 01 10 10" (right click on "Size" -> select Modify Binary data). Close Registry Editor. That's it.
My on screen display driver is the latest. I am using Vista Business 64 bit, so maybe the driver for 64 bit has not been fixed yet.
Thanks again! -
After I updated to iOS 7.0.2 my lock button is not working properly
After I updated to iOS 7.0.2 my lock button is not working properly I push the button many times and after many failed attempts it locks and sometimes not. I had to use the accesibility tool to lock it manually from the screen, this is really annoying.
I guess it is.
Do you have a question, or are you just sharing your experience with us? -
I dropped my iPhone 5S and it landed flat on it's face (it was in a protective case). Since then my touch screen display is not working properly. I have white and grey lines and/or blocks crisscrossing the screen both horizontally and vertically. Screen responds to touch in odd random ways, but rarely does what I am trying to do. Can't call or receive calls because can't dial or answer phone via swipe. Can't text or read incoming texts. All functions seem to be working except that I can't access them because the touch screen is acting up. If I move the phone around it randomly accesses different apps or functions, but I have no control over them once the appear on the screen. Touching screen just causes phone to randomly choose something else to open. What have I damaged?
Shanegang77 wrote:
What have I damaged?
We cannot possibly tell. Obviously some hardware inside. Take it in to an Apple Store. They will offer you the opportunity to swap the phone for $269 in the US. Prices vary by country. -
Z2 double tap to wake up the screen is not working properly when taking it out of pocket
when i take my phone out of my pocket, the double tap function is not working properly, sometimes i have to tap over and over to wake up the screen.
do you know why? does same thing happen to yours ?
and please dont tell me not to use it. i have paid 700$ and i have right to use my phone fully functioning.
any advice ?Actually it needs some practice, you need two gentle taps on the upper third of the phone (around the place where the clock shows on lock screen), tapping too hard or tapping on the lower part of the phone will require repeating the tapping more than one time. This is from my personal experience.
A proud Sony User since 2002
If I was helpful to you, thank me by Kudos -
My 5800 touch screen is not working properly.
Hi,
Frequently my 5800 touch screen is not working. Some times I am unable to use the screen. It's just hung. The call, menu and disconnect buttons only work during this time. Can any please let me know what might be the problem.?
Thanks in advance,
Tarun Konduri.Tarun_Konduri wrote:
Hi,
Frequently my 5800 touch screen is not working. Some times I am unable to use the screen. It's just hung. The call, menu and disconnect buttons only work during this time. Can any please let me know what might be the problem.?
Thanks in advance,
Tarun Konduri.
Tarun_Konduri wrote:
Hi,
Frequently my 5800 touch screen is not working. Some times I am unable to use the screen. It's just hung. The call, menu and disconnect buttons only work during this time. Can any please let me know what might be the problem.?
Thanks in advance,
Tarun Konduri.
Dear all,
I had the same issue with my nokia 5800, finally I found very interesting thing, I have been doing everything to bring my phone back to original condition where simply I can touch and access the phone.
Actually the issue was with the thin plastic piece which was put on the touch screen for its protection. I was struggling to touch and access the phone but i coudnt for almost 2 weeks, it was directing me to bottom left corner touch buttons of the phone and automatically opens and activate functional which I didn't want.
Solution was, I simply removed the thin plastic layer from the phone , Now it works fine.
Hope this will help. -
ESS is not working properly after upgrade from 4.7 to ECC6.0
ESS Scenario in 4.7
4.7 Scenario:
The IMG configuration u201CWork and Life Eventsu201D is done to map them with the PZM3 service (Home Page) to get them as different folders/links on the home page as given below:
List of Services used to set up ESS:
Sl.No Functionality Service/EWT/URL Name Standard/ Customized Type
1 Home Page PZM3 Standard Service
2 Inbox BWSP Standard Service
3 Calendar BWCA Standard Service
4 Whou2019s Who PZ01 Standard Service
5 CPF Display http://192.168.0.2:7070/omcpf NA URL
6 Payslip Display ZPAYSLIP_USER Customized Service
7 Section 80C PZ88 Standard EWT
8 Section 80 PZ80 Standard EWT
9 Form 16 HRESSIN_F16 Standard EWT
10 Address PZ02 Standard EWT
11 Bank Information PZ03 Standard Service
12 Open Appraisals Not Available NA Service
13 Emergency Address PZ05 Standard EWT
14 Family/Dependents PZ12 Standard EWT
15 Personal Data PZ13 Standard EWT
16 Previous Employers PZ28 Standard EWT
17 Apply Leave WS20000081 Standard Service
18 Leave Overview WS01000109 Standard Service
19 Leave Balance PZ09 Standard Service
20 Loan Application ZLOAN Customized Service
ECC6.0 Scenario:
In ECC6.0, flow based services are no more supported by ECC6.0 and Dynpro based services are supported.PZM3 (Home Page) is a flow based service.
There is no replacement provided for PZM3 service, so the IMG configuration is not possible for u201CWork and Life Eventsu201D.
OSS ticket raised, but no solution for IMG u201CWork and Lifeu201D events.
List of Services would be used to set up ESS:
Sl.No Functionality Service/EWT/URL Name Standard/ Customized Type
1 Home Page PZM3 Standard service
1)this service is not available
2)SAP does not provide any replacement.
3)PZM3 is not supported in Integrated ITS. No direct solution proposed.
4)Given reference of few notes.
5) A dynpro (module pool screen) based IAC needs to be created and links need to be provided on that screen. Generated HTML page is modified to access the services via URL or by OKCODE.
Screenshot attached below.
2 Whou2019s Who PZ01 Standard Service
1)this service Available
2)Not Working properly.
3) The problem may be because of the dependency with SAP Query. Either Query is missing in the new system or not having the proper authorization. Needs to be debugged and finalized.
7 Section 80C PZ88 Standard EWT Available
8 Section 80 PZ80 Standard EWT Available
9 Form 16 HRESSIN_F16 Standard EWT Available
10 Address PZ02 Standard EWT Available Only EWT Available. Service needs to be created to access the EWT.
11 Bank Information PZ03 Standard Service Available EWT Available. Service needs to be created to access the EWT.
12 Open Appraisals Not Available NA Service EWT Available. Service needs to be created to access the EWT.
13 Emergency Address PZ05 Standard EWT Available EWT Available. Service needs to be created to access the EWT.
14 Family/Dependents PZ12 Standard EWT EWT Available. Service needs to be created to access the EWT.
15 Personal Data PZ13 Standard EWT EWT Available. Service needs to be created to access the EWT.
16 Previous Employers PZ28 Standard EWT Service Available
17 Apply Leave WS20000081 Standard Service Available, but not working No solution is proposed yet.
18 Leave Overview WS01000109 Standard Service Available, but not working No solution is proposed yet.
19 Leave Balance PZ09 Standard Service Available, but not working No solution is proposed yet.Ya ramakrishna,
Even easier is for you to send us the mail ID of your client. We will do the work, then send them an idoc of message type INVOICE and for you a post card of course.
Please do the needfull,
Julius -
20" iMac, display not working properly, otherwise OK
I have a 20" imac with 10.4.11 loaded, Have had it for about 2 years, no problems at all except occasional wake-from-sleep issue. All of a sudden, the display has quit working properly. The computer sounds like it boots fine, but the display only shows a very deep blue (not black)and the light ind the lower right corner is "on".
I tried holding a flashlight up to the front as some have suggested, and I do not see see anything at all. This would seem to rule out backlighting or screen brightness issues. I have also reset the PSU and the P-ram, also to no effect. Tried booting from the 10.4 disk, also to no effect.
My teenagers won't admit having any problems, but one of them did admit to turning off the system several times using the power button in an attempt to reset AirPort. Any thoughts? the only other easy thing I can think of is the battery, could that be causing this much trouble? do the display cables ever detatch from the MB or anything like that? any ideas greatly appreciated.
Thanks, EricHey Eric,
This is from the Service Source:
"Screen is dark, fan is running and the hard drive is spinning. You may hear the startup
chime as well.
1. Reset parameter RAM. Press Command-Option-P-R during startup before “Welcome to Macintosh”
appears.
2. The system software could be damaged. Start up from the system CD that came with the computer.
3. Remove the user access panel on the bottom of the computer. With the unit powered on, check if a red
LED is visible in the access door. If the red LED is on, power is on. If you don’t see the LED glowing
red, follow the steps under the symptom “No Power”.
4. Disconnect the A/C power cord. Place the unit in the service stand and remove the user access plate.
Press the PMU reset button on the logic board. Refer to “Resetting the PMU on the Logic Board”
mentioned earlier in this chapter.
5. Check for external video. Connect an external monitor to the mini-VGA port. If you don’t have external
video, replace the main logic board. If you do have external video, go on to the next step.
6. Open the bottom housing and verify that all the cables are securely attached. Pay special attention to
the video cable (located near the modem). If the cables are securely attached, go on to the next step.
Warning: Whenever the bottom housing is opened for service, you must do two things:
• You must clean the original thermal film from the surfaces joining the thermal interface layer and
reapply thermal paste to the thermal pipe.
• The bottom housing has four torx screws that must be tightened to at least 17 in.-lbs. If you do not
have a torque driver, you will have to make sure these screws are tightened by hand FIRMLY, BUT
NOT FORCIBLY. Or, purchase the service tool (076-0899) in order to ensure the thermal pipe is
firmly mated with the top base. If the bottom housing is not securely attached to the base in this
fashion, the CPU may overheat and become damaged.
7. Check the connection of the video cable to the LCD flat panel display (under black tape).
8. Replace the inverter board.
9. Replace the LCD display. Important: If you are replacing the display, be sure to install the new display
shield and EMI gaskets that come with the new LCD panel. Installation instructions are included with
the new display panel. Additional display shields/gasket kits are also available separately as a kit, part
#076-0958.
10. Replace the neck assembly
11. Replace the logic board.
12. Replace the power supply board."
In my experience the connectors both on the logic board and on the back of the LCD panel have been known to come loose. I also have a neck assembly here that went bad.
If you need more info email me.
Richard -
On Screen Display not working on T61P running WXP SP2
This started with an error on 'tponscr.exe' when I hit a volume button. I reinstalled the Thinkvantage Hotkeys from the Lenovo site and I no longer get the 'tponscr.exe' error but the on screen display doesn't work (Volume does change tho). The Fn keys also do not work as well. System update also did not correct. Any help or suggestions would be appreciated. Thanks,
M/T 6457-C34 T61p WXP-SP2
Message Edited by SVOGT on 07-12-2008 05:37 AMI've had no luck with the latest HotKey drivers on my T61. I revereted to the driver version that came with the T61 and things seem to be working. In case you want that version, I've posted it to
http://www.jmbissell.com/7kvu13ww.zip
John -
Screen painter not working properly to edit an ALV screen
Hi I am stuck with a problem, I want to edit a screen which is an ALV report screen and add a custom button to its toolbar. But the screen painter is not opening properly so that I can see the screen layout and add a button.
Any help is greatly appreciated....HWat do u mean by the screen is displaying improperly? Is teh graphical layout not coming?
If so, you have to contact your basis team. you need to get the latest Gui version, and you need a particular port to be opened. -
Screen Capture Not Working Properly Since Upgrade
The following keyboard shortcut does not work on my laptop:
Command + Shift + 4 + Spacebar
When I have an external monitor connected, in mirrored mode, it doesn't work. If I disconnect the monitor or change the monitor arrangement into extended mode, it works fine. All the other shortcuts (e.g. CmdShift3) work fine.
Anyone else have this problem?OK, I've got a Mac Pro with an ATI Radeon X1900 card and two displays: an Apple 30" and a very old Apple 23" Cinema Display. The latter is attached using the very expensive Apple converter. I just put them into mirror mode and CommandShift+4Spacebar worked fine. If someone at Apple tried to duplicate the problem with whatever hardware they had on hand and got the same result I just did (namely it works), then they would conclude there is no inherent bug in the OS regarding mirrored displays and screenshots. There are two other possiblities:
1. Something is conflicting in your installation of the OS
2. There is a bug in the OS, but only for some particular hardware configurations
To eliminate the first possiblity the only thing that can work is for you to do a new installation of the OS on your hardware and see if the problem is still present. So in this case a re-install is not a frivolous suggestion.
There is one other thing to try: create a new test user, leave it as Apple creates it, log into that account and try the screenshot shortcut. That will eliminate some peculiarity associated with your regular account. Of course, it doesn't eliminate the possiblity that something is wrong with the OS as installed, or that something you have installed that is available to all accounts is causing the problem.
You might also try a Safe Mode boot. Problem is that disables everything not strictly necessary to run the computer, and I'm not sure whether the extension(s) necessary for dual displays and screenshots would work correctly, but it is certainly worth a try. Hold down the Shift key when you hear the startup chime, and wait until you see the login screen with the "Safe Mode" message (the boot will take longer than usual). Login and see how (or if) things work.
Francine
Francine
Schwieder -
HP pavilion dv6-6c01ej On-Screen Display not working
Hi, I have an HP pavilion dv6-6c01ej and I want to use the on-screen display, to see for example when the volume when I turn it up or down (also for brightness change and so..).
I looked in the Programs and Features in Control Panel and saw I have the last version of the driver (version 1.3.5).
I couldn't find the actual prgoram in the Start menu (I don't even know if it exists).
I wanted to download it again so I can try uninstall and install, but the file could not be found, using this link:
http://ftp.hp.com/pub/softpaq/sp55001-55500/sp55152.exe
From here:
http://support.hp.com/us-en/drivers/selfservice/hp-pavilion-dv6-6c00-entertainment-notebook-pc-serie...
I don't know if it's the same driver for all the pavilion dv6 pc's.
Also, I tried downloding the HP MediaSmart for that, but the download failed for some unknown reason.
So, How can I turn this feature on?
This question was solved.
View Solution.Hi:
See if this version works...
http://h20566.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_101310_2 -
[Problem Solved] On screen display not working on T60
I replace my xp with a Vista Business.
All the drivers are installed. But the on screen display is not working well. Nothing display when I press the volume up/down/mute button. However, other buttons like Fn+F3, Fn+F5 do display on screen.
Anyone knows how to solve this?
Thanks a lot.
Message Edited by szsy on 10-02-2008 08:11 PM
Solved!
Go to Solution.problem solved.
looks like I need to install a Lenovo System Interface Driver. This is just for ATI graphic card users and nVidia users don't need it.
Thanks a lot. -
Visible (Screen Only) not working properly
This seems like it should be such and easy thing to figure out, yet I cannot understand why, when I print the form, it still prints. Can someone troubleshoot this one for me please? Here's my form:
https://acrobat.com/#d=Bktug5D4t0vBOcim5z2AQA
The field that is set to Visible (Screen Only) is the dropdown field "Reason". But it still prints.
Thanks!
JoI was having this same issue, and after reading this post, tried the following...
1) Changing the version of my document to v8.
Result: this didn't work. Objects marked "visible: screen only" still print.
2) Creating a NEW form in v8. Copying and pasting the objects from my previous form in this form.
Result: this works. Objects marked "visible: screen only" still print.
So based on this little experiment, and the previous posts here, I think it is safe to say that the document must be created as v8 right from the start. Simply changing the version of a pre-v8 form will not work. -
Screen Sharing not working properly
Leopard is wonderful except for iChat screen sharing. Here is what happens. I am in a video chat and invite someone to share my screen, or they invite me to share theirs. The sharing works fine. Then, when it is time to end the sharing, instead of returning to the original chat, you have to reconnect the call again. Moreover, I get communication errors and cannot reconnect until I dump the preferences and restart the machine. I have contacted the second tier of service at Apple and they are working on this, but I have heard nothing yet. Is it possible that iChat has an issue and can I just reinstall iChat from the Leopard CD?
Thanks,
PhilAfter an hour if pulling out my hair, I finally had an idea of what might be causing the crash... I noticed I had my old iSight plugged in (the external firewire iSight) into my Apple Cinema Display. I unplugged it and iChat screen sharing worked PERFECTLY. You should also know that I don't have problems with my iSight, it works well on Video Chat and Audio Chat and even presentation mode but, it screwed up screen sharing.
In conclusion, if you're experiencing sudden connection losses with iChat screen sharing, check to see if you have an iSight plugged into your Mac and unplug it.
Maybe you are looking for
-
How can I hide the extension in multiple pdf files?
I make a lot of PDF files and would like to know if there is a way to hide the extensions without using the 'Finder - Preferences - Advanced' tick box method. It is very time-consuming doing this for every file.
-
Contract automatically set as source of supply for PR/PO
Hello MM experts, I am thinking about implementing the following scenario and I have 4 questions PM service order that creates a Purchase requisition automatically. I will have in the system a MM contract for that material / vendor / plant It is pos
-
Airport express not allowing PC or xbox on to network with WEP password
Hi there Ever since we switched from PC to Mac about 5 years ago our airport express (purchased 2007) has not allowed a PC or other gaming device on to it's network. I have two MacBooks at the moment which needed to be configured with slightly differ
-
Yahoo mail ,using ff shows resolutions not high enough but works withchrome
When I log into Yahoo mail I get a popup stating my computer resolutions are too low. Nothing has changed. I can log in OK using Chrome.or Google on this same computer.
-
hopehouseoc.com/index3.htm I can't get it to line up in Windows, but in all things Mac, it's okay. Can someone see the quick fix that I'm not seeing? thanks, -c