Log me in pro file transfer

Just installed a new computer,I log on to log me in pro with no problem but I can't transfer files from one computer to another.... Any Suggestions? Thanks Marc B.

Are you going in through safari, or using the app in the store? If you are using the app, and getting that error, you should drop the developer a note. The whole point of a app is that it should have all the code needed to do what you are trying to do.

Similar Messages

MacBook Pro to MacBook Pro File Transfer

Perhaps too basic of a question, but I haven't been able to find the answer elsewhere.
I'm getting a new MacBook Pro in a couple of weeks and need to transfer non-application files from my old (early 2011) MacBook Pro to the new one. In the previous migration, also MacBook to MacBook I just started up the old MacBook as a Firewire Target disk and copied the files to the new one. Firewire has apparently been phased out because it is not on the new MacBook. Does Thunderbolt work in the same way? Can I hook the pair up using a T'bolt to T'bolt cable, start my present, soon to be old, MacBook up as a Target disk (hold 't' during startup?) and copy the files over?
Relatedly, what is the preferred or recommended method of transferring files used with Apple's Index-type Applications (i.e., iTunes, Mail, and iPhoto)? Is it OK to simply copy the files over to the appropriate location or should I use the "Import" or "Add to Library" choices with the new program? After twenty years of near-religious devotion to constant upgrading to the newest OS version, I've slacked off the last couple of years and am currently running OS 10.8.5, iPhoto 9.4.3, Mail 6.6, and iTunes 11.1.5, should version number figure into the answer. With my previous transfers, the "old" machine had the latest software and thus wasn't an issue.
Thanks!
Chris

Hi CB,
Not a problem, as Eric has pointed out correctly, TM works with Thunderbolt. If you have't got one on the old MBP, you would require a FireWire to Thunderbolt adaptor, for your new Mac that has not got a FW port. Then FW to the FW port on your old MBP.
Of course, with both having Thunderbolt, TB to TB - and whala! It is fast!
Let us know about the fun with the new Mac
Leo

Mac Pro to MacBook Pro - File transfer problem

I just bought a new Mac Pro. It is connected to my Airport Extreme via ethernet. The Airport Extreme is connected to my cable modem vis ethernet.
The Mac Pro and the MacBook Pro appear in the others Shared part of the side bar. I have checked the permissions of the files (command I) that I am trying to transfer and in every case there are the usual names- admin, my name, and everyone - with Read & Write privileges. However, there is another one called (unknown) with read only. I can not change the privilege nor delete the name from the list.
1. I have repaired permissions on both machines
2. In "Get Info" I changed permissions and added "Administrators" and made it "Read & Write" to the files I am trying to share.
*The Problem is:*
I can transfer from the MacBook Pro to the Mac Pro but when I try to transfer from the Mac Pro to the MacBook Pro , I get the Alert:
"You may need to enter the name and password for an administrator on this computer to change the item named " Blah Blah"
When I click on "Continue", I get this message:
"The item "Blah Blah" contains one or more items you do not have permission to read. Do you want to copy the items you are allowed to read?"
When I click continue I get:
" The operation cannot be completed because you do not have sufficient privileges for some of the items".
From the Mac Pro I have no problem moving files from one folder to another on the MacBook Pro.
Transferring worked perfectly when I had my old PPC G5 (where the Mac Pro is in the loop).
Can someone please help? Anyone have an idea or two?
Message was edited by: Garner Lewis

Have run into this problem repeatedly in the past two weeks. I first discovered I could tether my MacBook Pro to my Droid X and access the internet for free, so I was elated. After a couple of days I could no longer connect the phone to the Mac via Bluetooth as you describe. Then it magically came back a week later, and after two days I lost it again. I spent about 3 hours troubleshooting and solved it. I hope this works for you.
Open Network Preferences on the computer
HIghlight Bluetooth PAN
Select the ADVANCED tab
Click on "Renew DHCP Lease"
That did it for me.
Good luck,
Rob

Macbook Pro file transfer problem

hello ppl...I hav an NTFS formatted External Hard Disk..so is there any way by which i can transfer files from mac to HDD without formatting it...plzz do let me know if its possible..

thanks a lot dude.....problem's solved...i found much flexible tool for it.... SL NTFS looks better

File transfer between internal drives extremely slow

Since the upgrade to the latest Lion OSX 10.8.5 on my Mac Pro, file transfer between internal drives is extremely slow. I used Disk Ulitly to repair the drives but no use. What could be the cause? Thanks

Yes I have been transfering the same type of data in the same manner as before, this happened only recently. For example if I transfered lets say a 100MB single file from main HDD to 2nd internal HDD it would have taken around 10 seconds nwo it takes a minute or so. Also my iTunes library is located in the 2nd Drive and since this issue when I play music it keeps cutting off and coming back, I am sure this is due to the slow transfer speed of the drive. I can't figure out why it has gotten so slow, is it the drive or the OSX?

I woke up at 3am to find my MacBook Pro in the middle of a file transfer using AirDrop.

I woke up at 3am to find my MacBook Pro in the middle of a file transfer using AirDrop. I had not accepted any file transfers via AirDrop as I was asleep so I am a bit confused by all the posts that say that the only way it will work is by the end user accepting a request to transfer files. I am on a home network which has both a soft and hard firewall. I checked my firewall logs and have no signs of intrusion or intrusion attempts. I checked my network map to see see if someone had brute forced my router and was using it but the only assets listed were mine. My router is set up to not be accessable from wireless computers, and is filtered to only allow use by a assets in the MAC Address list. I am an IT by trade but this is my first mac so I am not completely savy in the ways of the ways of macdom. I have found several posts with suggestions on how to turn off and came up with the following terminal command "defaults write com.apple.NetworkBrowser DisableAirDrop -boolean YES". My question is this, how is it possible that my AirDrop was activated and in the middle of a file tranfer if I did not initiate it? I do have a MacMini on my network but its WiFi is turned off so the transfer was not with it. I have read on different posts that you cannot AirDrop if the computer is not on the same network but there were no foreign assets on my network. So my question is this
1. If AirDrop can not be used with another computer if it is not on the same network, how was it being used?
2. How can AirDrop be used to xfer files if I did not accept or initate it?
It seems to be a pretty big security hole to me. Any suggestions or help would be greatly appreciated.
Ethan

It could just be a bad disc - I use Verbatim and have only had one fail in a ten-year time period. Try getting a batch of Verbatims and see if you have any problems. I didn't even know that there were Kodak branded discs...
Clinton

HT204144 File transfer using Airdrop from iphone to Macbook Pro

File transfer using airdrop form Macbook Pro to iphone is working...but from iphone to Macbook Pro is not working, Why?

Hi Brok25;
Thanks for the question. The resource below explains the specs and settings that are needed for AirDrop. Check the settings and look to see if your MacBook Pro is listed.
Mac Basics: AirDrop lets you send files from your Mac to nearby Macs and iOS devices - Apple Support
http://support.apple.com/en-us/HT203106
Sending files to and from an older Mac
If a Mac you're using with AirDrop was manufactured before 2012, you can send and receive files with other Mac computers.
On the sending Mac, click "Don't see who you're looking for" in the AirDrop window.
Select the option to "Search for an Older Mac."
On the receiving Mac, open a new Finder window and click AirDrop in the sidebar.
Tips for sending files
Make sure Wi-Fi and Bluetooth are enabled on your Mac and your iOS device. Although you don't have to connect to a specific network, Wi-Fi needs to be on to send and receive files using AirDrop.
Move your devices closer together. AirDrop is designed to work within a range of approximately 30 feet (9 meters). If you need to send a file to someone farther away, consider using File Sharing, iCloud, or email instead.
If you're using a firewall on your Mac, you won't be able to receive AirDrop files if you have enabled "Block all incoming connections" in the Security & Privacy pane of System Preferences.
Make sure your devices meet system requirements for AirDrop.
System Requirements
To see if your Mac works with AirDrop, make sure you’re in the Finder by clicking the desktop (the background area of your screen), or by clicking the Finder icon in the Dock. Then, check to see if AirDrop is listed as an option in the Go menu. If you don't see AirDrop listed, your Mac doesn't support this feature.
In order to transfer files between a Mac and and an iPhone, iPad or iPod touch
your iOS device needs to include a lightning connector
your iOS device needs iOS 7 or later installed
your Mac needs to be a 2012 or later model with OS X Yosemite installed
Your Mac and iOS device both need bluetooth and Wi-Fi turned on. You do not have to be connected to a specific Wi-Fi network.
To transfer files between two Mac computers, you need the Mac models listed below with Wi-Fi turned on and OS X Lion or later installed.
MacBook Pro (Late 2008 or newer)*
MacBook Air (Late 2010 or newer)
MacBook (Late 2008 or newer)*
iMac (Early 2009 or newer)
Mac Mini (Mid 2010 or newer)
Mac Pro (Early 2009 with AirPort Extreme card, or Mid 2010)
*The MacBook Pro (17-Inch Late 2008) and the white MacBook (Late 2008) do not support AirDrop.
For help identifying your Mac, choose About This Mac from the Apple menu. You can refer to the Apple Support website to find out if your iPhone, iPad or iPod Touch includes a lightning connector.
Cheers,
- Judy

TFTP 'configuration update' from 5508 WLC fails stating reason as '%Error: Config file transfer failed – Unknown error –refer to log'

Dear Experts,
I have two WLCs and other management devices as part of same subnet. I am able to upload ‘configs’ from all the devices on to my TFTP server. However when I am attempting to do the same from one of my WLC, it is failing consistently stating error message as:
‘%Error: Config file transfer failed – Unknown error –refer to log
Has anyone else too faced the same issue and how would we overcome this? Any specific debug that could help get more details on it?
Though the error message says, refer to log but still I don’t see anything that gets reflected in ‘Monitor logs’ which is related to ‘configuration file’ upload failure.
WLC code: 7.4.100.0
PFA as the error snippet.
Thanks and Regards,
Adnan

Hi Kaneswaran,
Just a soft reboot helped me solved the problem :). Still I am on 7.4 and facing no issues after this.
Apologies for coming too late to respond. Getting a down time window was not that easy and so was much delayed to try soft reload. I am still on 7.4 and facing no issue.
Glad that in your case it starting working all of a sudden. Could you please verify from 'show tech-support' to confirm if by chance your WLC had undergone any crash that could have caused the WLC to reload and thus accidently fixing the issue :)
Best Regards,
Muhammed Adnan

Configure log file transfer to downstream capture daabase!

Dear all,
I am setting up bidirectional replication among 2 database server that are Linux based and oracle 11gR1 is the database.
I am following the document Oracle Streams Administrator Guide, Have completed all the pre-configuration tasks but I have confusion with this step where we have to configure log file transfer to downstream capture database.
I am unable to understand this from the documentation.
I mean how do I configure Oracle Net so that the source database can communicate with each other in bi-directional replication?
Configure authentication at both databases to support the transfer of redo data? How can I do this?
Third thing is the paramter setting that obviously i can do
Kindly help me through this step.
Regards, Imran

and what about this:
Configure authentication at both databases to support the transfer of redo data?
Thanks, ImranFor communication between the two databases, you create streams administrator at both the databases. The strmadmin talk to each other.
Regards,
S.K.

MacBook Pro Retina - Fan/Heat During File Transfer

Hey guys,
I just had my MacBook Pro Retina in for repair because of an 4HDD/11/400000000: Sata (0,0) error and they replaced the SSD. I have a 2.7/16/768 configuration. One of the main issues I noticed was periodically slow file transfers, load times and boots hanging etc. and a secondary reason was a high-pitched buzzing with heavy disk usage.
My question now is... when I'm doing something as simple as a large file transfer, or installing some apps etc. the MacBook really heats up and the fans really start spinning sometimes. I've never known SSD access to heat up a computer so much. Is this normal behaviour that everyone else is experiencing with their systems? To clarify: this happens when not doing anything else with the machine other than copying files around, also when copying files to/from my external drive which is connected through FireWire on the back of my 27" Thunderbolt display which is then of course connected to the MacBook via the Thunderbolt port.
Expected behaviour? Seems odd to me, but this is my first MacBook so don't know if that's the 'norm' or not.

I've managed to get the fan speed down to a reasonable, less audible level by using that old VRAM terminal command to enable me to keep the internal display disabled whilst the lid is open. I've had to shift quite a lot round on my desk to make this happen, but I guess it was the only way. It now runs 3 screens under similar loads at approximately 3500prm.
Taking your advice into consideration, I raised the rear feet and this enabled further decrease in fan speed. I guess one of those laptop stands will augment this effect, and I will look into them.
Anyway, thank you for your help!
Thanks,
Richard

Since Prelude doesn't work with Red footage, how can I add logging info to a file in Premiere Pro

Since Prelude doesn't work with Red footage, how can I add logging info to a file in Premiere Pro CS6?

RED footage has a restriction on metadata. We are looking into what it would take to get full metadata support into our system, but you cannot tag red footage at this time.

Time machine file transfer very slow during OSX 10.7 re-install

I am using a macbook pro, and was running 10.7. (not sure exact version, and cannot look now, but should have been up to date) I tried the free upgrade to Mavericks, but it failed and said I had a disk error. At this point I could not boot back to 10.7 so I booted with apple-R. I tried to do a repair from disk utility but that failed so I erased my hard drive. Then I proceeded with an install of 10.7, which proceeded fine. I got to a point where it asked about transferring files, (forget the exact wording) and I said to use my time machine backup (from right before I tried the upgrade - backup was 80GB) and I started that. It has been 16 hours and it still has not finished. The external hard drive (Lacie) clicks / whirs, and I see signs of very slow progress... (seems to be at about 80% now judging by the progress bar) but it can go hours without any noticeable change. The "time remaining" information is variable -- going up and down -- and is clearly not correct-- has said 1.5 to 2.5 hours for the last 12 hours
Any ideas? should I just wait a few more days   should I abort and restart the file transfer (if so, what is the best way to do this?)
I cannot provide details on the computer since it is still busily restoring (I hope), but it is roughly 3-4 years old, lots of free space on hard drive (>100GB),

These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter the word "Starting" (without the quotes.) You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard."
Each message in the log begins with the date and time when it was entered. Note the timestamp of the last "Starting" message that corresponds to the beginning of an an abnormal backup. Now
CLEAR THE WORD "Starting" FROM THE TEXT FIELD
so that all messages are showing, and scroll back in the log to the time you noted. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
☞ If all you see are messages that contain the word "Starting," you didn't clear the text field.
☞ The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. Don't post more than is requested.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
☞ Some private information, such as your name, may appear in the log. Anonymize before posting.

UCMA 4 and back to backing a file transfer request

OK, I know that file transfer isn't technically supported on UCMA 4.0, but I wanted to take another look at it and see whether there was a way to b2b a file transfer request. After all, there's no reason that it shouldn't work if the messaging is correct,
right? The scenario I have is A <-b2b-> app <-b2b->B. I have an IM conversation going on between A and B, so now I'm trying to set it up so that A can send a file to B.
So far I've extended the platform to accept file transfer requests by creating my own call and factory classes, and then registering them using RegisterPlatformExtension. This means that when A sends a file, the INVITE gets delivered to my application.
Now I'm taking that INVITE and creating a new b2b call. A file transfer request looks something like this:
TL_INFO(TF_PROTOCOL) [0]16A8.4B28::02/10/2015-19:53:05.007.001d492f (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265))[3939761282] $$begin_record
Trace-Correlation-Id: 3939761282
Instance-Id: FDB3
Direction: incoming
Peer: 10.0.154.20:49282
Message-Type: request
Start-Line: INVITE sip:[email protected] SIP/2.0
From: <sip:[email protected]>;tag=eafd3e699d;epid=ccd5657cac
To: <sip:[email protected]>
Call-ID: 0acf0330423241258576d7c5cc42aa01
CSeq: 1 INVITE
Contact: <sip:[email protected];opaque=user:epid:d2lIs-103l2YSpDwCSajtAAA;gruu>
Via: SIP/2.0/TLS 10.0.154.20:49282
Max-Forwards: 70
Content-Length: 1920
Content-Type: multipart/mixed;boundary="----=_NextPart_000_0026_01D04541.4641C2D0"
Message-Body:
------=_NextPart_000_0026_01D04541.4641C2D0
Content-Type: application/sdp
Content-Transfer-Encoding: 7bit
Content-ID: <[email protected]>
Content-Dis; handling=optional; ms-proxy-2007fallback
v=0
o=- 0 0 IN IP4 192.168.200.71
s=session
c=IN IP4 192.168.200.71
b=CT:99980
t=0 0
m=data 21300 TCP/RTP/SAVP 127
a=ice-ufrag:lYAu
a=ice-pwd:y0gkW4r9zGSW6E2VdtMprlEh
a=candidate:1 1 TCP-PASS 2120613887 192.168.200.71 10856 typ host
a=candidate:1 2 TCP-PASS 2120613374 192.168.200.71 10856 typ host
a=candidate:2 1 TCP-ACT 2121006591 192.168.200.71 21300 typ host
a=candidate:2 2 TCP-ACT 2121006078 192.168.200.71 21300 typ host
a=candidate:3 1 TCP-PASS 2120612863 10.0.154.20 31624 typ host
a=candidate:3 2 TCP-PASS 2120612350 10.0.154.20 31624 typ host
a=candidate:4 1 TCP-ACT 2121005567 10.0.154.20 3921 typ host
a=candidate:4 2 TCP-ACT 2121005054 10.0.154.20 3921 typ host
a=cryptoscale:1 client AES_CM_128_HMAC_SHA1_80 inline:4CZbzYM/GYDbygj8JwMTodKo85C4Xx7TMzeMIuBU|2^31|1:1
a=crypto:2 AES_CM_128_HMAC_SHA1_80 inline:Ohlo65gDsUvxCF39A382Rl4vGL+SG9R/lUEYU/br|2^31|1:1
a=crypto:3 AES_CM_128_HMAC_SHA1_80 inline:EZ7Zm3K0H/WW5K49LAk9/C0T8x8nhkumJOycSek7|2^31
a=setup:active
a=connection:new
a=rtcp:21300
a=mid:1
a=sendonly
a=rtpmap:127 x-data/90000
------=_NextPart_000_0026_01D04541.4641C2D0
Content-Type: application/ms-filetransfer+xml
Content-Transfer-Encoding: quoted-printable
Content-ID: <[email protected]>
Content-Dis; handling=optional
<request xmlns=3D"http://schemas.microsoft.com/rtc/2009/05/filetransfer" =
requestId=3D"13">
<publishFile>
<fileInfo embedded=3D"true">
<id>{67190A30-C59F-480D-96DD-5F3941C39C49}</id>
<name>dbchange.log</name>
<size>3609</size>
</fileInfo>
</publishFile>
</request>
------=_NextPart_000_0026_01D04541.4641C2D0--
$$end_record
I've got my b2bed invite looking almost identical to the original invite by creating a custom MIME type on the CallEstablishOptions for the back to back call using something like this:
Regex r = new Regex(@"^((.|\n)*)(\<request)((.|\n)*)(request\>)((.|\n)*)$");
Match m=r.Match(args.RequestData.GetMessageBodyString());
content=string.Format("Content-Transfer-Encoding: quoted-printable\r\n{0}{1}{2}",m.Groups[3],m.Groups[4],m.Groups[6]);
opt.CustomMimeParts.Add(new MimePartContentDescription(new ContentType("application/ms-filetransfer+xml"),System.Text.ASCIIEncoding.UTF8.GetBytes(content)));
opt.CustomMimeParts[0].ContentDispositionHeader = new SignalingHeader("Content-Disposition", "render; handling=optional");
So far the only differences I can see in my outbound message vs the original SDP are that the Content-Transfer-Encoding might not be seen as a header (since the SignalingHeaders property on the MimePartContentDescription is read only), and the Content-Transfer-Encoding
on the first MIME part (created by the BackToBackCall) is missing (even though I specified it on the PassThroughHeaders). Even with all of this though, I still get a 488 on client B when I attempt the transfer (even though the invite goes through).
What I'm wondering though, is whether there's any way at all to get this working the way I'd expect, where a file gets transferred directly between A and B, without my bot having to receive it first. The other approach I've looked at is binding my
own media provider class to customize the SDP, but if this MIME part approach isn't going to work, then I have a feeling the media provider won't work either.
Any suggestions on where to look next?
Thanks!
Chris

Chris,
I am trying to do something similar to this and from what I have read and in talking to MS is that you need to extend the Call and Flow class which it looks like you have been able to do. Could I bother you to share what you have written? Maybe we can help
each other out on this. I am basically trying to create an application that will be able to capture a file transfer and save it, then send the original request on to the intended recipient.
Thanks in advance,
Anthony

MBP (mid-2009) freezing, slow installations and file transfer

I bought the latest MacBook Pro model and installed Snow Leopard on a cleanly formatted hard drive. I have tried migrating via ethernet and FireWire from my iMac, but the migrations failed either due to freezing (via FireWire after roughly 24 hours of file transfer) or by an error message (ethernet with Migration Assistant).
Only through a Time Machine backup was I able to transfer my account files to the MBP, which again totaled at over 20 hours of transferring. The system was a mess, clogged constantly by freezing and spinning beach balls of death for durations lasting around 10-20 seconds during which music would clip after 5-10 seconds of everything not responding, this being accentuated especially during installations. I decided to format and try anew.
Now I've formatted the hard drive, installed Snow Leopard and will transfer my files manually onto a clean account. Installations take a long time although SL installation is within 30 minutes, iLife took 1.5 hours to install 5 GB. During the installation Safari stopped responding, as did the entire system, and the spinning beach ball would keep spinning. Watching a 480p trailer in Quicktime made the entire computer freeze up (no video/audio) for 10 seconds halfway. Transferring 136 GB (my Music folder) will take around 15 hours according to the estimate after 10 minutes of transferring.
I've sold my iMac now and all I have are the files on my external hard drive. I want to get them onto my MBP ASAP but the slowness is preventing me from doing what needs to be done and it's very frustrating. When I try to boot into Hardware Testing by holding D down the computer doesn't do it no matter what (Application DVD in or not, plugged into power or not). I've tried resetting PRAM but I get the same inaction.
Any ideas?
Edit: I've done Disk Utility to no avail, it finds nothing wrong.

Installed, still getting freezes with spinning beach balls. Transfer says it would take 1 hour opposed to that 15 hours, but it stops transferring after X amount of gigabytes (from 0.5 to 5), not do anything for a while and then continue, stretching the estimate to over 2 hours after some time. I don't know if this is just with the hard drive.
The freeze-ups are frustrating as **** and make for a very poor experience. Any ideas to get to the bottom of this? I still haven't been able to boot into the Hardware Test no matter how much I try.

File transfer: AFP vs FTP

Setup:
Cable modem to Linksys WRT54g broadcasting only in G only mode for PBG4.
AEBSn#1 in bridge mode via Ethernet from Linksys, N only mode, broadcasting wirelessly.
AEBSn#2 is wirelessly extending N-only from AEBSn#1, and is connected to a mini with external hard drive.
Using PBG4, if I mount a volume from the mini and transfer a file, transfer time is very slow: approx. 20 minutes for a 200MB file. If I FTP from PBG4 into the mini, transfer time is 2 minutes.
(I think the same happens if I use a Macbook Pro connected to the N-only network, but it's in for repairs right now, so I can't be sure.)
Any idea why the transfer times are so different b/w AFP and FTP and, more importantly, what I can do to remedy this? Thanks.

Same problem here. I have two AEBS Gigabit in bridge mode. Transfering a file via FTP or with Apple Remote Access (ARD) brings up to 3 MB/sec. Same file and same configuration connected via AFP only brings 60 kB/sec.
I hope somebody has an idea how to fix this.
Thanks in advance

Log me in pro file transfer

Similar Messages

Maybe you are looking for