Logging directly into enable mode on a PIX using TACACS

I have setup TACACS authentication on a PIX running 6.3(3). I can authenticate using TACACS just fine, but do not get put directly into enable mode. The ACS server is setup to do so, it works for routers and switches, but not the PIX box. If I put the "aaa authentication enable console TACACS" in the config I must enter the enable command and use the same password I logged in with to get into enable mode. Without the command, I have to use the configured enable secret password to get into the enable mode.
Does anyone know it there is a way to configure the PIX to log someone directly into enable mode via TACACS?
Thanks in advance

Hi,
PIX does not support exec authorization. Hence user cannot login to level 15 directly.
Regards,
Vivek

Similar Messages

Log into Device with AAA, how do I get right into enable mode?

I am using a Cisco ACS server with an RSA server behind it. When the user is authenticated from the ACS server, I want them to go straight into enable mode, not have to type the enable mode password. What line am I missing?
aaa authentication login ACS group ACS_servers local enable
aaa authorization exec ACS group ACS_servers local
aaa authorization commands 15 ACS group ACS_servers local
aaa accounting commands 1 default start-stop group ACS_servers
aaa accounting commands 15 default start-stop group ACS_servers
line vty 0 5
login authentication ACS
authorization commmands 15 ACS

The configuration in question is for telnet, but I do need to design my new console access connection. Console access would be either remotely or on-site, but I don't feel comfortable giving priv 15 right into it. I plan to use the same authentication method on the console (ACS group 1st, local database 2nd) and will just have to enter the enable password through the console.
One more question on the aaa config, I kept getting this error in the log:
AAA/AUTHOR: config command authorization not enabled
So I added:
aaa authorization config-commands
I don't know if it was needed because I could still execute config-commands, but it kept giving me that warning if I didn't have that line.
Also, do I really need this line if the ACS server is taking care of priv 15 authorization:
aaa authorization commands 15 ACS if-authenticated

Aaa authorization (device doesn't always go into enable mode)

When I log into the 4500 switch with my domain account, I get priv 1 only and have to “enable” with the local enable password to get to priv 15. How do I set this up to get directly to enable? The ACS 5.1 is setup with a authorization/shell profile for Priv 15, no problems there.
2821-RTR2#show run | incl aaa
aaa new-model
aaa authentication login default group tacacs+ local enable
aaa authentication login CONSOLE local-case line
aaa authorization exec default group tacacs+ none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
4500 that drops into enable mode
4500-SW1#show run | incl aaa
aaa new-model
aaa authentication login default group tacacs+ local enable
aaa authentication login CONSOLE local-case line
aaa authorization exec default group tacacs+ none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common

On the non-working device enable:
debug aaa authen
debug aaa author
debug tacacs
and post the results.
Also, on ACS 5.1 review the details for the authen/author on both the working and non-working devices and see if the desired shell profile is picked for the non-working device.

Login to directly into "privilege mode"

Hi All,
I have created users and given them telnet access to router 7200.
They have full privilges(15) but everytime they login they login into user-exec mode instead of privilege mode.
Is there a way to skip user-exec mode and allow the users to login directly into privilge mode so they dont have to enter password twice?
Thanks!!

Opening a new thread might be a good idea - though at this point we have gone far enough (and I am not sure how much further this discussion will go) that we might as well just continue this thread.
While IOS devices have mechanisms that will allow you to configure that a user goes directly into privilege mode I do not believe that this works on the ASA - at least for the command line. If you login to ASDM to manage the ASA you will go directly to privilege mode. But for command line (SSH, telnet, etc) you will go to user mode and be required to enter another password for privilege mode. I do not know a way to get around that for ASA command line.
HTH
Rick

Can I open directly into slideshow mode?

Is it possible once having cretaed a photo gallery to also create a seperate link to open a web page directly into Sl,odeshow mode without having to first go to the gallery page and click on click on Play Slide Icon link for the Slideshow pop up.?
It would be great to have the option of creating alink directly to the slideshow.
Hope someone can help me out please..
David

without having to first go to the gallery page and click on click on Play Slide Icon link for the Slideshow pop up.?
no you can't, because the pop up slideshow window widget requires the thumbnails page to be opened first, so that the image stream loader loads in the images.
It would be great to have the option of creating alink directly to the slideshow.
but you can have slideshow directly on the thumbnails page, if you know how to work iweb javascript widgets.
Here is my example: http://www.cyclosaurus.com/iWeb2/Photo_Albums/Pages/Muse.html
javascript is linked to the example.

TACACs+ commands not dropping me into enable mode

Hi All,
I've just comfigured the following on a router running IOS 15. All my other devices are running the old tacacs commands but thought I'd try the new CLI version.
It works, e.g get prompted for username/password and authenticates against our AD Server (integrated with ACS4.2). I get into the router but into usermode.
My other devices drop me straight into Priv Mode. Only difference is the the new commands v the old commands but I can't see anything that is different in relation to putting me into Priv mode.
Any ideas?
aaa group server tacacs+ ABC_ACS
server name ABC_TAC
tacacs server ABC_TAC
address ipv4 172.27.10.10
key secretkey
aaa authentication login ACS_List group ABC_ACS line
aaa authorization exec ACS_List group ABC_ACS if-authenticated
aaa accounting exec ACS_List start-stop group ABC_ACS
aaa accounting commands 15 ACS_List start-stop group ABC_ACS
line vty 0 4
password test
authorization exec ACS_List
accounting commands 15 ACS_List
accounting exec ACS_List
login authentication ACS_List
length 0
transport input ssh

Make sure you defined the username with a static privilege level of 15 otherwise it will not be able to pass the enable authentication.
If ACS 5.x or higher go to the policy elements: Shell Profile and make sure you have one assigned for a static maximum privilege of 15 and most important that its applied into a access-policy rule

Should Apple TV be put into standby mode when not in use?

Anyone,
When I am done watching Apple TV, should I put it into standby mode or leave it on? Just want to take of my new favorite toy!!!!

I tend to leave them on all the time - standby mode isn't particularly low power as lots of things are still active.

My iPad randomly goes into sleep mode while I am using it?

All of a sudden, when ever I use my iPad 2 it goes into sleep mode. It did it three times while I typed this message. As I am running an app it will just go into sleep mode with out me doing so and I have to press the home button to wake it up. Doesn't matter what app I am running. I have 4gb of storage available. Most of the time it brings me back to the app I was using when it went to sleep. Has anyone else suffered this issue. I am running the latest iOS 6.0.

What "issue"? This is perfectly normal. By default, all (fairly-recent) Apple products will go to sleep if left idle for a certain period of time. This is NOT normal, however, if in the app, you are pressing buttons on the screen. If you are doing something like reading, for example, try setting your iPad to not go to sleep that quickly.
(Google how, I don't completely remember.)

Using IMAC mail am unable to send messages. I can log directly into internet provider webmail and send no problem.

Am able to send and receiev emails user Internet provider webmail, but am unable to send messages using IMAC Mail.

have you verfies that all the mail settings are just like the mail providers guide ?

Software update my phone has gone into recovery mode and I cannot use it after doing the latest software update ???

I have just done the latest software udate ios7.1. the phone is showing the itunes logo and the connection lead. I plugged it into the pc and a message comes up saying this iphone is in recovery mode and must be restored before it can connect to itunes, but i cant get into the phone as the screen wont do anything. I clicked on the pc to restore the phone but nothing has happened. The phone is an Iphone5c
Please help thanks Teresa

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps...
Take your time... Pay particular attention to Steps 3 and 4.
After you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766
Make sure you have the Latest Version of iTunes (v11.1.5) Installed on your computer
iTunes free download from www.itunes.com/download
Note. Once the Device is asking to be Restored with iTunes... it is too late to save anything... and you must continue with the Recovery...

Can I hook iPad directly into USB printer? I am using cellular service only.

Can I hook an iPad directly to a USB printer (non wireless) in areas where I have no wireless networks?

no, unfortunately not.

Pix/Radius and enable mode

Hi all, I am trying to get a pix 6.3 to authenticate telnet users via radius with a Microsoft IAS server. This works well, but Im trying to get it where when they log in, it just dumps them into enable mode, instead of typing in the enable AD credential again. Anyone have any insight on how to do this? Its a IAS configuration thing I know, but not sure what to do with it. Thanks in advance.

If you mean on firewall,
Username: alfa
Password: ********
pixfirewall#
Rather then,
Username: alfa
Password: ********
pixfirewall>
pixfirewall>enable
Password: ********
pixfirewall#
The unfortunately, Pix firewall does not have this concept, like IOS devices have.
On IOS you can get the user log directly into enable (Privileged exec) mode by passing attribute,
cisco av-pair as shell:priv-lvl=n or on some IOS only using Service Type as Administrative will do the trick.
Where, n is the privilege level.
AND, there has to be an EXEC authorization command on the IOS device, e.g.,
aaa authorization exec group radius....
Unfortunately, that is not the case for the Pix firewall, they have a different OS.
Regards,
Prem
Please rate if it helps!

RSA SecurID and Cisco ACS integration for user(s) with enable mode

I thought I had this problem figured out but I guess not.
I have a Cisco 2621 router with IOS 12.2(15)T17. Behind the
router is a Gentoo linux, RSA SecurID 6.1 and Cisco ACS 3.2.
I use tacacs+ authentication for logging into the Cisco router
such as telnet and ssh. In the ACS I use "external user databases"
for authentication which proxy the request from the ACS over
to the RSA SecurID Server. I installed RSA Agents with
sdconf.rec file on the Cisco ACS server. I renamed "user group 1"
to be "RSA_SecurID" group. In the "External user databases" and
"database configurations" I assign SecurID to this "RSA_SecurID"
group.
Everything is working fine. In the "User Setup" I can see dynamic
user test1, test2,...testn listed in there as "dynamic users". In
other words, I can telnet into the router with my two-factor
SecurID.
The problem is that if test1 wants to go into "enable" mode with
SecurID login, I have to go into "test1" user setting and select
"TACACS+Enable Password" and choose "Use external database password".
After that, test1 can go into enable mode with his/her SecurID
credential.
Well, this works fine if I have a few users. The problem is that
I have about 100 users that I need to do this. The solution is
clearly not scalable. Is there a setting from group level that
I can do this?
Any ACS "experts" want to help me out here? Thanks.

That is not what I want. I want user "test1" to be able to do this:
C
Username: test1
Enter PASSCODE:
C2960>en
Enter PASSCODE:
C2960#
In other words, test1 user has to type in his/her RSA token password to get
into exec mode. After that, he/she has to use the RSA token password to
get into enable mode. Each user can get into "enable" mode with his/her
RSA token mode.
The way you descripbed, it seemed like anyone in this group can go directly
into enable mode without password. This is not what I have in mind.
Any other ideas? Thanks.

ACSE - Logging into Privileged Mode

I have configured one client, remote agent and the ACSE. I am able to authenticate into the network device via AD. It prompts me for credentials then I am in user mode. I then issue the enable command to enter privileged mode. It then prompts me to authenticate again. My question is how do I configure ACS to enter me directly into privileged mode once I have successfully authenticated? I do not want to first be in user mode then have to authenticate again to enter privileged mode. Any help would be greatly appreciated. Thank You!

Bring users/groups in at level 15
1. Go to user or group setup in ACS
2. Drop down to "TACACS+ Settings"
3. Place a check in "Shell (Exec)"
4. Place a check in "Privilege level" and enter "15" in the adjacent field
Also make sure we have exec authorization enabled.
aaa authorization exec default group tacacs+ if-authenticated
Regards,
~JG
Do rate helpful posts

Apple tv loses home sharing when my computer goes into sleep mode

Just recently, my Apple TV says that home sharing is off when my computer goes into sleep mode. It never used to do that - any suggestions?

I have the same problem here. Always back-ed up with Time Machine (OSX 10.9 Mavericks) to Western Digital drives. MyBooks, MyPassport 1TB (USB 3.0), all works fine. Time Machine is actually doing back-ups overnight. Since I got this new 2TB MyPassport Ultra USB 3.0 it's working perfect during days, but every morning when I wake up the MacBook from sleep, I get this annoying error:
Time Machine couldn’t complete the backup to “MyPassportUltra”.
Unable to complete backup. An error occurred while creating the backup folder.
Latest successful backup: Today, 02:27 am
I'm also not able to write anything to that drive, or unmount it. It stil shows up in Finder, and I'm able to read all the data perfectly fine. When I do a Disk Utility Verify Disk directly after, I get this:
Checking volume
disk3s2: Scan for Volume Headers
Invalid Volume Header @ 0: I/O error
Invalid Volume Header @ 2000021315072: I/O error
disk3s2 is not a CoreStorage volume
Error: This disk needs to be repaired. Click Repair Disk.
I don't click Repair Disk, as this will probably screw up my partition. Instead, I have to unplug the USB cable (which is bad for the drive, there's no time to park the drive's heads) and plug it in again. After clicking Backup Now, Time Machine immediately starts backing up, and the drive works fine the rest of the day.
I contacted WD Support, and they are sending me a booster USB cable. As System Information reports, the drive receives enough power though:
Current Available (mA): 900
Current Required (mA): 224
Unfortunately there's no firmware update for this drive, which will probably fix this. See this topic: https://discussions.apple.com/thread/4196704.

Logging directly into enable mode on a PIX using TACACS

Similar Messages

Maybe you are looking for