Logging for changing device configuration using cisco prime LMS / PI
Dear All,
How to see / set for
for changing device configuration (routers, switches) using cisco prime LMS / PI ?
and, how to see network topology diagram using PI / LMS?
Thanks,
Jerri
anyone can help. thanks.
Similar Messages
-
Device discovery in Cisco Prime LMS 4.1
Hi,
im using CISCO PRIME LMS 4.1 for manage my network, i ran a device discovery job using a ping sweep on the ip ranges of my network, ie 192.168.1.0/24, 192.168.2.0/24 and so on... the discovery found all my devices, but it discovered duplicate devices with illegal ip Addresses, ie
ip device
192.168.1.255 S1
192.168.2.0 S1
192.168.2.1 S1 (the real address)
all in reachable status.
i dont undestad why the program adds that repeated illegal addresses.. someone can help me with that issue??
how can i run the device discovery to avoid this problem?
Many Thanks.Julio,
Don't let LMS decide on what IP address it will manage the device.
For example, let LMS do a lookup of the sysname in DNS, then it will use the IP address coming back from the DNS as management IP.
This is what I do to avoid this.
But I also feel that LMS should be bright enough to never manage the same device twice. I think Campus DFM or RME will eventually figure out the 2 devices are the same, but they can't "fix" what is wrong in the DCR.
Cheers,
Michel -
Update IOS using Cisco Prime LMS 4.1
Hello everybody,
I have 10 switches 2960 and would like to uptade its IOS using Cisco Prime LMS 4.1.
How can I make that?
Thanks for all.Hi,
Kindly check the below link :
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.0/user/guide/configuration_management/swmgt.html#wp1369360
i hope this will help..
Thanks
Afroj -
Cisco Prime LMS MPLS monitoring
Hi all, have anyone used Cisco Prime LMS for MPLS xconnect monitoring?
Currently when these traps arrive to Cisco Prime LMS they are classified as "InformAlarm Unidentified Trap Generic".
Is it maybe possible to load the correct MIB for these traps and get Cisco Prime LMS to understand them correctly?
The raw traps looks like this:
xconnect down:
09:58:42.352760 IP (tos 0x40, ttl 245, id 12, offset 0, flags [none], proto: UDP (17), length: 114) routerhost.51591 > lmshost.snmptrap: [udp sum ok] { SNMPv1 { Trap(71) E:cisco.10.106.2 10.130.1.13 enterpriseSpecific s=1 424011509 E:cisco.10.106.1.2.1.26.2=2 E:cisco.10.106.1.2.1.26.2=2 } }
xconnect up:
09:59:48.597894 IP (tos 0x40, ttl 245, id 14, offset 0, flags [none], proto: UDP (17), length: 114) routerhost.51591 > lmshost.snmptrap: [udp sum ok] { SNMPv1 { Trap(71) E:cisco.10.106.2 10.130.1.13 enterpriseSpecific s=2 424018144 E:cisco.10.106.1.2.1.26.2=1 E:cisco.10.106.1.2.1.26.2=1 } }
I found some more info about the traps at:
http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=CISCO-IETF-PW-MIB-V1SMI
BR /CrilleHere is an update:
After discussing with TAC there seems to be 2 possible solutions in LMS right now:
1. Create a threshold that monitors the specific OID for the xconnect vc and generate alarm if it changes.
2. Configure the device to send syslog when a xconnect state changes and create an "automated syslog action".
I have not tried either of them yet so I dont know which one works best, but option 2 seems easiest (its a one time config). -
Error: while configuring logs for changes in infotype data
Hi All,
I am configuring the following Tables for maintain logs for changes in infotype data.
V_T585A, V_T585B and V_T585C
While configuring V_T585B, when i input * in 'field name' column it gives me an warning message " All data fields in **** infotype 31 will be deleted.
Please let me know, what does this warning message means?
Also, How is the report RPUAUD00 read?
Regards
SimranHi Simran,
you are not suppose to give the IT 0031-Reference Personnel Numbers in these tables. why because this will done at the time of Employee hiring only and we don't change this. if you change you will lost the old data in the IT.
Normally we assign only the IT which we change frequently for the master data. example like 0 1 2 7 8 9 27 582 - 589 2001 2006.
if you are configuring today means from today on-wards any changes had made to these IT's you can see in the report. before changes will not be seen. in the report you have to choose either long-term document / short-term document and remaining fields as per the requirement.
Regards,
Praneeth kumar -
Changing server for Cisco Prime LMS 4.2 installation
Hi,
I am planning to install Cisco Prime LMS 4.2 with 50 device license on a temporary server. My question is:
Can we install Cisco Prime LMS 4.2 on Server A, applied the license for 50 devices, and then several months later we uninstall LMS on Server A, reinstall it on Server B, and applied the same license for 50 users?
Is it possible and legal to do that? I am worry if the LMS license is binding to the first server's MAC address.
Thanks in advance.also :vmversion 4.1 and 5.1 both checked, hdd 256, scsi , memory 8 gig,
-
Cisco Prime LMS device unreachable dont know why
Hi
Currently running Cisco Prime LMS v4.2
I am trying to get some Nexus 7K Switches to work and become reachable.
They are running kickstart: version 6.2(2)
system: version 6.2(2)
Now as far as I can see i have 2 identical switches but one is unreachable and the other is reachable.
When i use my snmp tester they both work with the correct V3 auth/priv passwords and the correct ssh
works on the switches.
When i go to monitor/Troubleshooting Tools/Troubleshooting Workflows
Then for the non working one i get the following fails....
Device Information Device availability x
Collector Status
Data Collection Failure
User Tracking Failure
Fault discovery Failure
On the working one The above all are a Success.
Also
Reachability Details
Both ping and traceroute work fine on both switches
For the life of me I cannot see any difference in the configuration of the two devices.
Has anyone come across this before ?
I have attached a copy of the snmp config.
Thanks
SteveWhat is the server OS? Windows/Linux or Unix?
From the server to ping and poll device for SNMP and see if both device works fine?
SNMP walk is available under :
Windows : NMSROOT/objects/jt/bin
Linux/unnix/: /opt/SCOpx/objects/jt/bin
Example:
NSROOT/objects/jt/bin/snmpwalk -v2c -c public <ip_add> <OID>
Try to configure the problematic device for SNMP v2 and try to add it from there and test if it works fine.
-Thanks
Vinod -
Cisco Prime LMS 4.1 - Do access points use up a node count license?
Hi Everyone,
I wish to purchase Cisco Prime LMS 4.1, particularly Cisco part # R-LMS-4.1-500-K9 which support 500 Cisco nodes.
We have about 360 Cisco switches/routers/ASA/FWs/WLCs so the 500 nodes license would seem to suffice for now & for future growth.
We also have about 200 lightweight APs that are managed & monitored by our WLC/WCS/Navigator environment.
According to the device support documentation for LMS, it supports and I assume will auto-discover these APs.
Does that mean these APs will use up node licenses on LMS even though management of the APs is done by WLC/WCS? If so is there an easy way to suppress discovery of APs by LMS so we don’t have to purchase extra node licenses for LMS? Or, does LMS offer additional support features for wireless APs not already offered by WLC/WCS/Navigator?
Just trying to understand how many network node licenses for LMS I have to purchase.
Thanks in advance for your help,
Ian.Thanks but I just heard back from my Cisco SE and he assures me that an AP will NOT use up a license.
I've asked him to verify his answer for me.
Is your answer based on real world expereince (the best there is)? That is, are you running Prime LMS 4.1 and does it indeed use up a license for each light-weight AP it discovers & manages?
Thanks for mentioning options 1-3 but I do not wish to employ any of them. I don't mind buying the additional licenses for APs ... I just need to know if I have to or not.
Ian. -
Cisco Prime LMS - Device discovery
How do you configure Cisco Prime LMS Device Discovery, so that you can have two credentials sets for specific "special devices" (host based statement) and one for the of the devices (global subnet statement)?
Thanks in advance.Hi,
Here is the link to the document containing the detailed steps regarding Credential Sets.
After defining your sets then set up Credential Set Policies.
Thanks! -
Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure?
Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?
SF300 series is targeted for support in PI 2.0.
-
Changing DataSource Configuration using ConfigTool - Help Needed.
Hello Everyones,
I have an EP 7 which I have installed on a WAS ABAP + JAVA. The Data Soruce configuraion is in dataSourceConfiguration_abap.xml because of this I cannot create any new users in the Portal, can someone tell me how I can change this Config file using the ConfigTool and what procedure is to be used.
Thanks for your help,
John.
Message was edited by: John BraySee Changing DataSource Configuration using ConfigTool - Help Needed.
-
Resume hook for changed display configuration
Hi arch forum,
I need some help configuring my resume process. First the scenario:
I'm working with my notebook (ThinkPad T420s) on the train
and when I get off the train I close the lid and the notebook suspends. When I get to work
I drop the notebook into the docking station, where an external monitor is connected.
If I hit the power button on the docking station the notebook resumes without opening the lid,
but it does not check for changed display configuration. I have to open the lid and type my password to
get the new configuration started.
Question is: Is it possible to create a resume hook, so that X checks for the changed setup on resume before I opened the lid?
If someone could direct me to the right place in the wiki that would be great.
Now I should specify my configuration:
Gnome3 and proprietary nvidia drivers
Its a new installation so I have a systemd only setup (which takes care of suspend/resume so far)
If you need to know more, just ask.
Thanks for any help in advance,
arnoldHi,
I'm trying to buy the exact same configuration.
although i cannot find this 2429CTT on lenovo site anywhere, is available for selling on a known european supplier.
and my propose is to have 2 Monitors connected, so I'll follow this inquire very closely and hold my order until then.
do you have any update on it?
just by curiosity, what about the rest? how does the PC feels to you? everything else is working?
thanks -
Cisco Prime LMS 4.1 course needed
Hi folks,
In near future we're going to migrate our LMS 3.2 to new LMS 4.1.
Have anybody know if any Cisco courses for Cisco Prime LMS 4.1 are available to buy, order or download? If so, wher I can find it.
Thanks in advance for helpIf your employer is willing to let you travel to instructor-led classes, you could search for providers of the 5-day "Implementing CiscoWorks LMS 4.0". Here's a course outline of this class, from the intraweb:
1. Introduction to CiscoWorks LMS 4.0
Defining Network Management
Exploring the Network Management Process
Basics of CiscoWorks LMS 4.0
2. Getting Started
Installing CiscoWorks LMS 4.0
Logging into CiscoWorks LMS 4.0
Using the Getting Started Workflow
3. My Menu
Basics of My Menu
Managing Dashboards, Portlets, and Portal Layout
4. Inventory Management
Collecting Inventory and End User Information
Performing Device Administration
Viewing and Creating Inventory, User Tracking, and Switch Port Reports
Using Inventory Tools
5. Configuration and Software Management
Managing the Configuration Archive
Verifying Configuration Compliance
Using Configuration Tools
Using Configuration Workflows
6. Network Monitoring and Troubleshooting
Visualizing the Network with Topology Services
Monitoring Network Performance
Monitoring Network Response Time
Monitoring Syslog Messages
Monitoring Network Faults
Using Troubleshooting Tools
7. CiscoWorks LMS Work Center
Using Smart Install Work Center
Using Identity Work Center
Using Auto Smartports Work Center
Using EnergyWise Work Center
8. CiscoWorks LMS Administration
Using the Trust Management Menu
Managing Collection Settings
Performing Network Administration Tasks
Performing System Administration Tasks -
Drawing network topology in Cisco Prime LMS 4.2
Hi all:
I installed the Cisco Prime LMS 4.2 and managed to discover the Cisco devices and user devices like my PC stations.
Then I tried to draw the network topology from this LMS 4.2 and I found the topology under the Configuration and Monitor tab. By clicking to these two tabs, it appears a page of something like below:
Topology Services
You can use Topology Services to:
- View detailed xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
- Display the physical and logical services in your network
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
- xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxx
There is no action click on this page and it looks like an explanation page and cannot do anything.
May I know how to draw the networl topology by this Cisco Prime LMS 4.2?
Hope to hear the answer from anyone know about this soon. Many thanks!
Warmest regards,
tangsuanHi Mantej:
Thanks to your link and I have downloaded the Prime LMS 4.2 document.
I then read and installed the JRE first in 64 bits because my Windows OS is 64bits but it still prompts out the Java installation screen. I then installed the JRE in 32 bits.
After that, it has no more Java installation screen. It then request for downloading file at the Windows top bar. I follow the request to riight click to allow the downloading. The Java running and downlaod the file.
After that, I cannot see any difference. Meaning I still cannot access anything for Toplology Services to draw my network topology diagram.
May I know what should be happen and what is the next step to do the topology drawing?
Many thanks!
Regards,
tangsuan -
Cisco Prime LMS 4.1 - /cwportal/group/lms/lms not found error after login
After upgrading the MDF (Common Services) and the device packages on our Cisco Prime LMS 4.1 installation we now get an error after logging in. The error is as follows;
Status
Not Found The requested resource was not found.
https://X.X.X.X/cwportal/group/lms/lms
The top of the page is the normal menu and anything we choose there works fine so we only see this just after logging in to CiscoWorks.
Has anyone experienced this problem or do you have any idea what might be causing it?
The installation is running on a Cisco appliance.
kind regards,
MichelIt's being access from a client using Internet Explorer 8 (which is what I'm forced to use due to company policy) by access the DNS name of the ciscoworks server and logging in.. It worked previous to installing the patches so I'm not exactly sure what has happened. I'll try to get another PC to test from though to see if it's something to do with my browser or PC.
If I add -configuration to the url it works just fine.
Maybe you are looking for
-
I had a 3GS and never had a problem syncing recorded voice memos from my iphone to my mac. I would sync and they would show up in a folder in itunes called "Voice Memos". I have ensured that no settings have changed and the box to sync voice memos is
-
Hi, In a table we having date columns but data is loaded like below. e.g.- 0012/04/12 :00:00:00 however we need to do data fix for those columns to update first two digits (00) to 20 in the Table. e.g :- updated value : 2012/04/12:00:00:00 Please let
-
Hi, How can I create a mapping in OWB 11.2 for Multitable Insert? Thank you. -bzx
-
Two "Find" Requests for Bridge
I'd like to be able to find all the images that don't yet have any keywords assigned - perhaps a filter to "show items with no keywords only" or a sort option to sort "By Keywords". I'd like to be able to search (find) images by thumbnail. Meaning, I
-
Any video tutorials for "Greeting Card Shop?"
Hello. I just purchased Greeting Card Shop from the Mac App store as a viable alternative to my PC version of The Print Shop. There are no directions. Are there any video tutorials for this program (a la "Video Professor")? Thank you.