Logging inbound and outbound connections through my Linksys router

Hi There,
I have a Linksys wireless router (WRT54G series) that I use to connect to the internet with my cable modem. I would like to be able to configure my home network to log inbound and outbound connections through my router.
My router, which I bought brand new a couple of years ago, provides some very basic logging through its administration interface. I can view a current log of very recent (within the past couple of minutes) inbound and outbound connections/traffic. However, I would like to be able to configure my network to log all inbound and outbound traffic for at least 1 or 2 days and have this log saved somewhere so I can retrieve and review it at a more convenient time. I haven't been able to figure out how to do this with my current Linksys router and would like some help in configuring my system.
Is it possible for me to configure (perhaps with a firmware upgrade or even by replacing my older Linksys router with a newer one) my router to continuously log a day or more's worth of inbound and outbound connections? If this is possible, what changes do I need to implement? Does Linksys offer a wireless router that has more sophisticated logging capabilities? What is the longest log period that I can create with a Linksys router?
If it's not possible to create such a log with my router, then what other components would I need to log this information? I've thought about setting up a Linux server with two network cards installed to act as a gateway between my router and cable modem which will log traffic. Would this be a good strategy to implement logging?
Thanks in advance.
Tom
Message Edited by on 07-28-2007 07:44 AM
Message Edited by on 07-28-2007 07:50 AM

well...the router's in-built log will only provide basic information about the incoming/outgoing log . So, it will be a good idea to install a separate log viewer .....

Similar Messages

How to access a domain server which is targeted by Group Policy set to block Inbound and Outbound connections

Hi,
I have a practice lab with two physical servers 2012 R2, one of them is Hyper-V host and one of VMs is a domain controller. I was doeing some exercises with firewall rule deployment through Group Policy, so I created an outbound rule to block port 80 which
was targeted to Domain Computers. Now my other physical server has inbound and outbound connections set to block and domain controller cannot be contacted to update policy ( with rule removed ). At least that is my understanding. Maybe I messed up something
with the profiles too, because port 80 would not have block all outband traffic, or?
I am new to IT so my understanding is still poor.
Best
Robert

Hi Robert,
If we block inbound connections, all connections that do not have firewall rules that explicitly allow the connection will be blocked.
If we block outbound connections, all connections that do not have firewall rules that explicitly allow the connection will be blocked.
If we block outbound TCP port 80, it will mean all websites will be unreachable, for TCP port 80 is for HTTP.
Regarding Windows firewall security settings, the following article can be referred to for more information.
Windows Firewall with Advanced Security Properties Page
http://technet.microsoft.com/en-us/library/cc753002.aspx
Best regards,
Frank Shen

SAP inbound and outbound delivey in single shipment document

Hi
We are doing outbound and inbound delivery creation in SAP. These are dropped to OTM(oracle transport management system). OTM will create orders for deliveries and groups multiple deliveries into one shipment. This is sent back to SAP for shipment creation. Problem we have is SAP can have either inbound deliveries Or outbound deliveires in a shipment. Based on inbound shipment or outbound shipment in shipment document type. OTM does not has this restriction and can bundle both outbound and inound in single shipment.
Business scenario we have is multi pick and multi drop, where there is possibility that 1) inbound del from vendor for PO 2) Outbound del to customer for SO and 3) outbound/inbound del for STO from RDC to DC in a single sipment.
Please advice ow this can be achieved in SAP.
Best Regards
Edited by: M.N. Phani Sai on Oct 28, 2010 10:34 AM

It is not possible to involve both inbound and outbound deliveries in the same shipment. SAP has its deficiencies...
http://sap.ittoolbox.com/groups/technical-functional/sap-log-wm/inbound-and-outbound-delivery-in-the-same-shipment-3512217
http://help.sap.com/saphelp_erp60/helpdata/en/f5/04898047bd11d2bf750000e8a7386f/frameset.htm
You cannot place outbound deliveries and inbound deliveries together in the same shipment document. Nor is it possible to assign Items from a delivery or an inbound delivery to different shipment documents. You must decide at the delivery stage whether order items can be shipped together in one delivery and therefore require only one shipment.
Edited by: Csaba Szommer on Oct 28, 2010 11:05 AM

Multiple inbound and outbound plugs

Hi Experts,
Can anybody give an example scenario where we compulsorily need multiple inbound and outbound plugs for a view??

Hi snakar rao ,
Suppose we have three views, a , b, c. Suppose we have a requirement like we need a button move_to_b on a, a button back in b which will move back to a, a button move_to_c on b and a button move_to_initial screen on c.
in this case
we need one out bound plug in a which will be connected to inbound of b
one out bound plug in b which will be connected to inbound of c.
in this case a needs two inbound plugs, one is for navigating from b and the other is for navigating from c
if there is a requirement like we need to navigate from a to c directly also, in this case c need one more inbound plug thats to connect the inbound plug from a.
Regards
Sarath

How to do inbound and outbound interfacing using UTL_FILE?

dear members,
How can we do interfacing from a legacy system to oracle and vice versa using the UTL_FILE package. I mean how to do an INBOUND and OUTBOUND interfacing using utl_file.
regards
sandeep

Hi Sandeep,
I do not know if I got your question correct.
Here is my understanding of it, pls correct me if I am wrong:
You want to read from and write to the OS from inside the DB? Right?
There are differnt waysa to do so, depanding on your Oracle version:
1. you can use the initialization parameter UTL_FILE_DIR to specify a directory on OS where you can read from and write to through the package UTL_FILE.
2. You can use a directory object in the DB to manage read write access to the OS. This is also usable with the package UTL_FILE as location where to read from and write to.
=> CREATE DIRECTORY my_dir AS '/home/oracle/my_directory';
GRANT read , write ON DIRECTORY my_dir TO scott;
SELECT * FROM dba_directories;
You need CREATE ANY DIRECTORY system privilege for this.
You can use directory objects also for external tables.
With these you can read from flat files in teh directory on OS with a select statement as if it were a table inside the DB.
Does this go into the direction you were thinking of?
Hope it helps for the first.
Regards,
Lutz

Gl balance inbound and outbound

Hi sap gurus,
We are having legacy systems that should interact with sap.I need to know the following for the GL balances through inbound and outbound
1.How data will flow parallely into sap.what steps i have to follow to do this.
2.what user exits or idocs or interfaces i have to use.
3.how the GL balances data will trigger into sap.
Plz help.This is most urgent for me.
Thanks in advance
Kiranmayi

Hi Vijay,
I am assuming that you are asking about inbound and outbound process.
These process comes under SAP Electronic Data Interchange (EDI)
Outbound process--> When a document is sent from SAP system to any other system (to business partners say bank or vendors).
eg sending a quotation to vendor.
Steps:
1. Application doc is created
2. IDoc is generated
3. IDoc transferred from SAP to the Operating System layer
4. IDoc is converted to EDI standards
5. IDoc transmission to business partners
6. Status report sent to SAP system.
Inbound process is reverse of Outbound process-->When a document is sent from business partner to SAP system.
eg Bank sending account statement.
Steps:
1. EDI transmission received
2. EDI Doc is converted into IDoc
3. IDoc transferred to SAP layer
4. Appication document creation
5. View appliation doc.
ALE (Application Link Enabling) method uses tRFC (Transactional Remote Functional Call) port for communication and refer to same concept mostly.
Hope it helps.

Creating and Setting up web services for both inbound and outbound comms

Hi
I would like to know the process of setting up inbound and outbound web services using Siebel - is there a tech note /bookshelf article that can guide me through to setting up a 'new/custom' web service.
I have read up on bookshelf that both business services and workflows can be setup/exposed as web services. Now i would like to find out how to do this.
Any help appreciated.
Regards,
TS

As you begin to experiment with web services you should take a look at SoapUI. It is a freeware program that makes it a breeze to test both inbound an outbound web service calls. The bonus is that it can also be used to trace what HTTP is going back and forth along with giving you the ability to chain calls together. That is particularly useful for example if you are learning how to do web service calls within the context of a session. http://www.soapui.com/

Redundancy Design Inbound and Outbound

Please have a look to attached diagram.
I have 2 parts A & B. Part A already exist and running. We are planning to add Part B as show in the diagram.
Part A consists of ASA 5540 and 2921 as Edge Router and Microsoft TMG as Web Proxy for internal users
All other traffic routed to ASA. ASA handles NAT and ACL's
Objective of adding Part B is to have Redundancy Inbound and Outbound. However, firstly I want to focus on outbound redundancy then I will move to Inbound Part.
After adding Part B, TMG will have 3 NIC's. 2 NIC will be connected to ASA's and 1 to internal
For Web proxy fail over I will configure TMG ISP-R feature. But my concern is for other traffic
Therefore, please can someone help me what are best possible ways I can use for outbound failover.
Thanking in advance. I appreciate the help

Any help, please ?

JCA for JDE-XE - Looking for more inbound and outbound service examples

Where can I find more examples using JCA for JDE-XE inbound and outbound service / events.
Edited by: Channu on Sep 23, 2011 1:37 AM
Edited by: Channu on Sep 23, 2011 1:37 AM

Hi Ralf,
Yes, if you put a deny http, it would drop all packets for destination as http port, but be mindful that when you apply an access-list on your inside interface, it automatically activates the deny ip any any right at the bottom, you would be able to see that in the ASDM. So for the users that need be allowed access to the http, needs to be explicitly allowed http access, so your correct configuration would be:
access-list inside_access_in deny tcp host 192.168.1.1 255.255.255.255 any eq http
access-list inside_access_in permit tcp any any
access-group inside_access_in interface inside
This would block 192.168.1.1 to go to internet, but allow all others.
Second question, i haven't chceked the ASDM, but just remember out of memory, that this service option should be the protocol, whether ip,tcp,udp,esp or gre etc.
Moreover always try to block connections as closed to the source as possible, this would mean, if you want to filter traffic going from inside to outside, that should be done on the inside interface not outside.
Thanks,
Varun Rao
Security Team,
Cisco TAC

How to add Total Quantity in Inbound and Outbound Delivery screen

Hi,
I want to add Total quantity field in Inbound and Outbound Delivery screens.
In document flow i can see the line item quantities in ALV Format, but if i select Display the totals above the entry check box
in Change Layout--> Display, i didn't see any totals displayed.
Please help me on this?
Regards
Bhuvana

Hi
If the field is a customer field, see BADI 'LE_SHP_TAB_CUST_HEAD'
Regards
Eduardo

Sharing Handling Units between Inbound and Outbound Delveries?

Hello-
I could use some guidance with how to best setup a handling unit scenario for a Third Party Purchasing process.
1.) Sales Order for Third Party Purchased Material (Vended Finished Good) is created in ECC.
2.) Purchase Order is sent to supplier.
3.) Shipping Label is generated in SAP and is assigned a Handling Unit. Label is sent to supplier.
4.) Supplier affixes this label to product and ships it to our warehouse.
5.) Goods Receipt is performed via Purchase Order (MIGO).
6.) Warehousing activities and Post Goods Issue of Outbound Delivery are performed via this label and Handling Unit.
We would like to do a few new things with this process.
A.) We would like to have the supplier provide us with the HU on their ASNs and generate a Packed Inbound Delivery from it.
B.) We would like the same HU to eventually be associated with the Outbound Delivery to the end customer.
Is their a best practice to share a Handling Unit across an Inbound and Outbound Delivery?
Is EWM Cross Docking the best way to accomplish this?
Are there other proven approaches?
Thanks for your time and help.
-Ron

hi friend
Handling unit number for identity of packing materail , pallet material carrying the carton ,carton the carrying the material
like FG material and tray
identification number controlling the handling unit numbers.
with regards
dinesh

Need IDOC inbound and outbound programs

hi,
i am new to xi.
i want IDOCs , inbound and outbound / function module programs for PURCHASE ORDER
and GOODS RECEIPT.
ex: BD10 for material master (matmas01).
thanks and regards
v ijender

for purchase order.
ORDERS / ORDERS04
ORDCHG / ORDERS04
ORDRSP / ORDERS04
Programs
RBDMIDOC Creating IDoc Type from Change Pointers
RSEOUT00 Process all selected IDocs (EDI)
RBDAPP01 - Inbound Processing of IDocs Ready for Transfer
RSARFCEX - Execute Calls Not Yet Executed
RBDMOIND - Status Conversion with Successful tRFC Execution
RBDMANIN - Start error handling for non-posted IDocs
RBDSTATE - Send Audit Confirmations
FOr testing you can use WE19.
and also check the below link
http://www.erpgenie.com/sapedi/message_types_masterdata.htm
regards
kummari

Seeking recommendations for handling large binary documents with security(preferable) for inbound and outbound scenarios from OSB- SOA and SOA- OSB

Hi,
I am currently working on a project with the following requirements
1. Client transfers binary document (between 1-20MB in size) from OSB proxy to SOA composite to Content Management system
2. Client retrieves binary document (between 1-20MB in size) from Content Management system to SOA composite to OSB proxy
In otherwords, a inbound and outbound integration.
What I have tried so far and my results:
Scenario A
1. Enabled MTOM on SOA composite by attaching wsmtom policy
2. Created an OSB business service and consumed the SOA composite application
3. Enabled MTOM on OSB proxy and business service and configured it to pass by reference
Scenario B
1. Enabled MTOM and security on SOA composite by attaching wsmtom policy and SAML policy
2. Created an OSB business service and consumed the SOA composite application
3. Enabled MTOM on OSB proxy and business service and configured it to pass by reference
I have a demo integration setup that writes a binary document to a file using the above steps. My SOA composite has a file adapter that writes the binary data to an external file and it is exposed as a web service with a simple WSDL definition that has an inline XSD schema with an single element of base64binary type. I have added a mediator that maps this base64binary element node to the file adapter's input node.
Result for Scenario A with file size less than 1 MB:
Flawless execution with sub-second response times
Result for Scenario A with file size of 8MB
First attempt: SOA composite faults with database transaction related error, solved by increasing JTA timeout
Second attempt: Flawless execution, but file transfer took over 100 seconds to complete. This is very poor performance and my suspicions are that this cannot be the expected behaviour, but I dont know the internal workings of the SOA composite and why its taking this long.
Result for Scenario B:
The OSB business service does not accept/recognize the SAML policy in the WSDL and suggests to configure OWSM policies manually, but OWSM policy in OSB does not have the wsmtom policy. Regardless of this, any permutation of MTOM + WSS security in this integration scenario either did not work outright or MTOM optimization was not happening ie binary data was materalizing in the message body.
I have only about 3 weeks left to implement a viable solution and the closest ive come to a solution is Scenario A but that +100 second response time for an 8MB file is really worrying.
I would appreciate any level of guidance, recommendations or suggestions as to how I go about tackling this problem.
Thanks
regards,
Johnny

I think this is due to the underlying mechanism of weblogic classloading..
You can contact oracle support @ https://support.oracle.com to report issues. Roughly this is the process .
1- get the Oracle Customer Support Identifier (CSI) for the client you are working for.
2- Create a user profile quoting the CSI. This will send an approval request to oracle support admins at your client.
3- Get the oracle support admins at your client site to approve your request for support access.
4-Once they approve , you can access the support site and raise service requests.

To Monitor inbound and outbound messages for ECC 6.0 business system

Hi Guys,
I am working on ABAP proxy. I want to monitor the flow of Inbound and Outbound messages for my Business system (ECC 6.0).
XI server is on a different system.
I understand that SXMB_MONI is used for tracking XML messages. What kind of tracking can we do by this transaction in our Business system and the XI system?
And how do I know whether the outbound XML message sent is lying in the Sending Business system or in the XI system?
When I am testing my interface, there is a fault message generated. How do I know whether the fault message is being sent to XI?
Thanks,
James.

James,
Go to SXMB_MONI in your sending system.
Here you will find a message ID fro your Message.
Go to XI, --> SXMB_MONI -->Monitor For Processed XML messages --> Advanced Selection Crieteria and use the Message ID here to see if the Message has hit XI or not.
Likeiwse it can be traced in the target system as well.
The basic point, The messages will have same Message Id on your R3 and on XI.
Regards
Bhavesh

Single Function module to create inbound and outbound delivery

Dear Frens,
   I would like to know how VL10A is creating a deliverty document in background mode.
   otherwise can anyone help me with a single function module or BAPI or BADI which creates both
   inbound and outbound delivery.
Regards
Priya

Hi,
Try FM RV_DELIVERY_CREATE or GN_DELIVERY_CREATE.
For creating a delivery wrt PO u 1st need to have a sales order i guess.
Regards,
Amit

Logging inbound and outbound connections through my Linksys router

Similar Messages

Maybe you are looking for