Logic and 23.976fps for HD video production

Why doesn't Logic Pro recognize 23.976fps. you can set the timecode frame rate manually in the synchronization preferences and uncheck auto recognize incoming frame rate. but if checked, Logic recognizes 23.976fps as 24fps. Is this because Midi Time Code does not support 23.976? (or does it?) I use a Motu 828mkII firewire interface that has smpte timecode input that Logic recognizes. Logic seems to recognize all other incoming frame rates (29.97 non drop, 29.97 drop,25,30 non drop, 30 drop) but recognizes incoming 23.976fps as 24fps. this becomes a serious problem in the field when multitrack audio capturing while chasing timecode provided by video production trucks or bays. for HD video production, 23.976fps is happening more and more. does anyone have a solution? can Logic read any other timecode formats besides MTC?

yes. Logic does have a 23.976fps setting in the synchronization preferences. this works fine as a setting when working with transfered OMF sessions or transfered sessions from Final Cut as an internal session frame rate. but Logic will not chase external 23.976fps because Logic's external timing is based on Midi Time Code which does not support 23.976fps. If you feed Logic 23.976fps from an external timecode generator, it auto detects it as 24fps. so when capturing audio chasing 23.976fps the files are all timecode stamped incorrectly and are not running at video speed. Apple really needs to address this issue since they are on the forefront when dealing with HD video production with Final Cut and since Logic is their flagship audio software they need to figure this out. can anyone explain to me that I'm wrong because I'm thinking about switching to some other software that doesn't depend on MTC for external sync.
any suggestions please.

Similar Messages

Two questions: how do Skype and iChat compare for group video? quality, reliability, cost, etc are important. 2) Is my MobileMe ID what I need to use in the window in making an iChat buddy? It only says AIM above the window, online tutorial differs.

Two questions: 1) How do Skype and iChat compare for group video? Quality, reliability, cost, etc are important. 2) Is my MobileMe ID what I need to input in the window in making an iChat buddy? It only says AIM above the window, online tutorial differs, saying MobileMe, AIM, GoogleTalk (Jabber) all work. Thnx

Hi,
IChat uses better Video Compression than Skype does.
On a top flight Mac you can send a 640 X 480 pixel frame up to 30 frames a sec.
Skype can't match this.
iChat in Video is Peer to Peer. (you can actually Log out of the Buddy list)
Skype seems to borrow something from everyone's bandwidth to make connections.
What do you mean by Business account Tracking ?
iChat Adds (or can add) the First Name, Last Name of your Buddies and create an Address Book Entry
Whether you mark those cards connected with a company is up to you.
(I have heard of issues with earlier version of iChat and the Address Book that "saw" the Company Name as the part of the Name and linking several Screen Names to the one name
Audio on a Mac using Skype tend to be the same as the streaming needs are less.
However you have to rely on any PCs audio abilities from PCs which may not be to the same standard.
Mac to PCs in iChat and AIM can be difficult though. (It should work but it rarely as simple as Plug and go)
Skype may suit your needs better on ocassions.
9:11 PM Thursday; May 5, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.7)
, Mac OS X (10.6.7),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

Very recently, my computer stopped opening quicktime when I click on a video clip in iphoto, Its quicktime X, and it works to play videos if I open quicktime and then search for the video. How do I go back to quicktime automatically launching from iphoto?

Very recently, my computer stopped opening quicktime when I click on a video clip in iphoto. I have quicktime X, and it still works to play videos if I open quicktime and then search for the video. How do I go back to quicktime automatically launching from iphoto?

Well since I do not have iPhoto 7 I can only guess what may be: As far I can remember up to iPhoto 8, iPhoto insisted on Quick Time Player 7. As I can see you have Snow Leopard (Mac OS X 10.6) and there Quick Time X is the standard playaer. Basically Quick Time 7 is not part of Snow Leopard.
Can you please check if Quick Time 7 is installed under Applications->Utilitis (in 10.6 Quick Time 7 if presenet is installed not under Applications - there Quick Time X is - but under Application/Utilities).
If not: insert your Snow Leopard installation DVD.
Once the installer opens, double-click on the Optional Installs folder
Double-click the Optional Installs.mpkg package
Click continue.
Select the option for QuickTime 7 then click Continue to start the installation.
If it is there you may try to move the iPhoto prefernce file to another folder and let iPhoto create a new one.
Please keep the old file until you are sure that iPhoto works how it should.
The iPhoto preference file can be found under your home folder then Library then Preferences and there
com.apple.iPhoto.plist
As alraedy mentioned do not delet this file, since if something goes wrong you can put it back.

I just order the wrong product 10 min ago i want to cancel my subscription and get refunded for the wrong product that was chosen. How do i cancel this product before i'm charged???

I just order the wrong product 10 min ago i want to cancel my subscription and get refunded for the wrong product that was chosen. How do i cancel this product before i'm charged???

Not sure if you can cancel before you're charged (Maybe?) but here is where you cancel. Cancel your membership or subscription | Acrobat, Acrobat.com online services

Backward and forward buttons for AVI video

hi
is there a way to do a backward and forward buttons for AVI
video using lingo?

Yes it is. Use a behavior like this for the forward button:
property thisSprite
property dvSprite
on getPropertyDescriptionLIst
myPropList = [:]
myPropList.addProp(#dvSprite,[#comment:"enter the sprite
channel number for the video
sprite:",#format:#integer,#default:""])
return myPropList
end
on beginSprite me
thisSprite = me.spriteNum
end
on mouseUp me
sprite(dvSprite).movieRate = 1
end
although I'm not sure that AVI can play backwards, try this
for the reverse button sprite:
property thisSprite
property dvSprite
on getPropertyDescriptionLIst
myPropList = [:]
myPropList.addProp(#dvSprite,[#comment:"enter the sprite
channel number for the video
sprite:",#format:#integer,#default:""])
return myPropList
end
on beginSprite me
thisSprite = me.spriteNum
end
on mouseUp me
sprite(dvSprite).movieRate = -1
end
-----------------

Server Setup advice for a video production house

Hello Forum,
I recently started working for a small video production company, I need advice on the type of server and other hardware and services that will allow my co-workers to work efficiently. Here are some details:
Currently we are going to buy a new server, I am not sure what we should look at getting,
currently we use a mini mac running OSX server and have 6 iMacs that the editors and other staff use.
We also have a 15 TB Drobo network storage device which is attached to the mini-mac server we are going to replace.
The production team uses Final Cut and Motion to build documentaries.
The other issue is that need a way to connect the office in Baltimore to the office in Washington DC and ideally share files between each location, currently they cannot access the network from Baltimore and have to have a copy of the unedited footage on their own Drobo.
What type of server setup do you recommend? Quad core? speed?
Should we set up a VPN to connect offices or does someone have a better idea, if so what applications do we need?
I know windows networking pretty well, but Mac is totally new to me.Currently editing files from the server is really slow and files are usually pulled to the iMacs to do editing, burning DVDs from files on the server hardly ever works- they pull them local then burn the DVD and it works.
I would love to hear suggestions to help us get up and running.
Anyone know of a good website for server setup- Since there is no Domains in OSX that i know of, how can we secure the network? Links would be great.
Thanks in advance for any help and suggestions.

Well if your looking for performance. You could get a Promise VTrak E-Class RAID with 32TB of storage, later on you can add more chassis to the raid for more storage space. The raid can be expanded up to 160TB. (80 drive bays, each drive 2 TB)
Using fiber you could attach the raid to an xServer or Mac Pro (running mac os x server). You'll probable want at least 8 or 16 GB of ram on the server.
The server can run a copy of final cut server. Witch makes it easer to work as a group. Mac OS X server, when properly configured, can also be used to create a VPN between both locations.
Final Cut Server will let editors check in/out specific parts of the documentaries. So the project lives on the server; instead of scattered over every ones computers. Part of this is you can pull down thumb nails versions of the video to work off of. Only when you do the final render do you download the HD version of the video.
If you want even better performance on the editing stations. you could also upgrade to Mac Pros. Mac Pros have upgrade slots witch you can use to add fiber networking. You could also use the upgrade slots to add a black magic real time HD capture card.
Or if you want to keep the imacs. you might want to hook the server to a switch by fiber, and have the imacs connected to the same switch by 1000-T
If you call apple i'm sure they'd be happy to help you figure this all out.
for info on Promise: http://www.promise.com/apple/
for mor info on final cut server: http://www.apple.com/finalcutserver/

What's The Best Sharpening Technique For HD Video Production

I use Photoshop CS5 to produce stills for use in high def video production. After editing 400+ photos often using a modest <1 pixel radius & 100% smart sharpen I found that the results looked terrible. I'm going back and eliminating most sharpening. Is there a decent sharpening approach for this end use? I used to work with the unsharp mask which so far has produced better results.

Even though I've been doing DVD's for personal use for about 10 years it's only in the last 2 years that I've been doing 1080p Blu-rays and while the results can be excellent as you suggest there's less room for error as sharpening artifacts can show up. In the past I used an unsharp mask technique with very small radius (1 pixel or less radius & less than 100%) and the results have been pretty good. In my never ending quest to improve I tried the new smart sharpen which works on the edge boundaries and I also applied a conservatively low size & percent.
But I'm now of the opinion that while this looks great on small (24") HD displays of the tif image, it looked terrible in a test BD. The best way I can describe it is looking like a "cheap printed image" on my large screen plasma. Possible my conservative approach was not conservative enough. This may be fine for a printed image or even an SD video.
I can do some really good night citiscapes using high ISO @ about 2 stops under but they still need sharpening. If I were doing this professionally I'd use a tripod & lock up the mirror. But I'm not so I'm trying to help with the slight lack of sharpness. Same is true but @ lesser extent with daytime photos.
I also agree with you about not using sharpening at all. I found that no sharpening was better for my use than the smart sharpen as I applied it but an unsharp mask might be a little better than the smart sharpen.
Thanks Hunt
Alan

Best 2013 Mac for Pro Video Production with FC Pro X?

We run a small video production company and it's time to upgrade. What is the best current Mac configuration and product for video production. I have a 2013 Macbook Pro that is maxed out but I get choked down by the video card when doing more than 3 multi-cams.
So we need some systems that can handle more cam views and that speeds up produciton.
Thanks for your help.
~David

I recently took possession of a new Mac Pro (8-core) and it's obvious that it "was made" for FCPX. Unbelievable performance. FCP7...oh well, it works as well as could be expected, but no miracles. It's an old app that doesn't benefit from all the cores and memory, but still my standard.

What is the best way to setup premiere sequence for export when mixing 24fps and 23.976fps for final

What is the best way to setup a premiere sequence for export when mixing 24fps (CG) and 23.976fps (live action) for final output at 23.976 (vimeo and such).
Right now my sequence is at 24fps, and when I export to 23.976, my dialogues seem to shift.
Should I set my sequence at 23.976fps instead of 24fps?
Thanks in advance for the help, and sincere apologies if this is a noob question.
David

That makes it easy. Remove the CGs from the project. Go to Edit>Preferences>Media... and set the Indeterminate Media Timebase to 23.976. Then when you import the image sequence, PP will assign it the correct frame rate.
Edit in a 23.976 sequence.

Storage location and Batch updation for components in Production Order.

Hi Friends,
After creating Production Order,need to update components with Storage Location(RESBD-LGORT) and Batch(RESBD-CHARG).
Plese any one can help me by providing FM/BAPI for the same(Update Component level)
Points will be rewarded.
Thanks,
Prb.

Hi Prathap,
Path - OCHA
Condition type,access sequence, strategy type,
Work on automatic batch determination. Assign standard search procedure to order type dependent parameter, check against manual entry.
Make sort sequence for material by CU 70, tick ascending order, Then assign component in COB1, enter selection values and sort sequence. In finish product material master set automatic batch determination.
System will copy the required material with batch & storage location, also check against manual entry.
I think it will solve your problem.
Regards,
Suhas

Suitable SD and SDHC Cards for Capturing Video for FCP?

Not exactly an FCP topic but this is the only forum that comes anywhere near!
Until a few weeks ago I assumed that all SD and SDHC cards were equal with regard to capture speeds.
Now I know better and have discovered that for trouble-free (consumer) video capture you need a Class 6 card to be safe.
I note that SD cards (by definition 2GB or less) have no speed classes.
I have trawled the internet, including the SD Card website but can't find any mention of the reason for this.
Is this because small SD cards are very fast or simply because nobody would conceivably use them for video?
I am asking because I have a small stock of 2GB cards which, if possible, I would like to use for short videos in the near future.

I've not used FCE so can't add anything there. Perhaps Tom W will drop by. He would know.
Regarding the VHS footage. You really ought to think about using a Time Based Corrector (TBC) between your VTR and the digitizing device. They will help deal with mis-timed frames (the 'tearing' effect) as well as chroma shift.
The Canopus ADVC-300 is the least expensive one I've seen and as an added benefit, it does the Analog/Digital conversion for you as well.
Good luck.
x
Do your part in supporting your fellow users. If a response has been Helpful to you or Solved your question, please mark it as such as an aid to other lost souls on the forum.
Also, don't forget to mark the thread Answered when you get enough information to close the thread.

Recommend new colour laser printer? Small and wifi capable for latest apple products,

Which new colour laser printer? I need small as possible, but wifi capable for latest apple products (OS 10.7 and mobile iOS 5). Not used wifi printing before, so getting confused with specs. Not high usage, want better speed than inkjet

Icpap wrote:
You mentioned some office-level multifunction copier, though, costing more: which one would that be?
The new imageRUNNER ADVANCE C2225 with the Booklet Finisher-M1. This finisher will fold and saddle-stitch your booklet on the fly for up to 5 sheets of A4 paper - making a 20 page booklet. And the printer driver for OS X will re-order the pages in your document so you don't have to get the page order correct before you send the print job.

Logic and coding needed for CU42

Hi,
I want to write a BDC program for transaction CU42 inorder to change single level BOM explosion to multilevel.There are around 10k materials.
So please provide me the logic and if possible coding for that.
Regards,
Ramesh

Hi Ramesh,
Check the below tables.
CUCO                           Additional Data for Configurable Objects
CUCU                           Dependency Source Code Base: Source text:
CUCVRNT                     Variants of Constraints
CUEX                            Dependency Storage - Compilation
CUFM                           Customizing: Class/Config: Screendesigner
CUICONTEXT                 Control Table for Context in the iPPE Work
CUKB                           Administrative Information for Dependency
CUKBT                          Text Table for Dependency Maintenance Admi
CUKN                            Dependency Storage - Variants/Configuratio
CULL_TRACEFILTER      Filter for Low-Level Configuration Trace
CUOB                           Assignment of Object to Dependency
CUOBOM_CHANGE      Manually Changed Items in the Order BOM
CUPE                           Extension to BOM Item for Variants
CURSADD                    Dependency Net Additional Data
Pls reward if it is useful.
Regards,
Boobalan Suburaj.

Schedule changes and validity dates for prices in product catalog(SRM-MDM)

Hello!
I'm working on a project that is going to use SRM-MDM and the question is if it is possible to schedule changes(for example to add new prices that have a validity period, can you make the changes now that are going to be valid from 1st of februari?Or can I add products today that are only going to be available to buy from a particular date?).
The other question is if it is possible to have a validity period for prices and when the date is valid,then the product is shown in the catalog.In the same way that when the date is not valid, the product is not shown in the catalog.Can this be made automactically?Can a logic be build to choose which products are going to be shown in the catalog?
Do you have any suggestions for those issues?
Thanks in advance!

Dear Poster,
As no response has been provided to the thread in some time I must assume the issue is resolved, if the question is still valid please create a new thread rephrasing the query and providing as much data as possible to promote response from the community.
Best Regards,
SDN SRM Moderation Team

Does anyone know if there is a way to connect the iPad 4 to a canopus box and use it for capturing video live?, Does anyone know if there is a way to connect the iPad 4 to a canopus box and use it for capturing video live?

I am the Video Coordinator at Samford University and have found the quality of video capture on the iPad 4 AMAZING, however I need to convert all my files through a canopus in order to Capture and Cut live like I do with a regular video camera. I can get the tripod and mount for the iPad, I was just wondering if anybody knows exactly how/if there is a way to connect to the canopus from an iPad.
Look forward to hearing what you guys and girls say.

I'm a bit vague about what it is you wish to accomplish. Are you trying to capture video through an external box? If so, that's not posssible with any of the Canopus boxes I'm familar with. In fact I don't know of any external video capture solution that works with an iPad, though I can't state definitively that none exist. I really don't think an iPad would be well suited for this even if it's possible. I'd strongly suggest you look into a MacBook Air or one of the current MacBook Pros. Those are far better suited for on-the-fly video capture and editing.
If that's not what you mean, please post back and explain further what it is you wish to accomplish.
Regards.

Logic and 23.976fps for HD video production

Similar Messages

Maybe you are looking for