Logic express 8 on my dual G4 MDD

i... I have a G4 MDD, and when i open LOgic Express 8, i have a message...you need 1.25 gig processor minimum... but i have a dual 1 gig. Is it possoble than logic doest'nt work good with a G4 Dual processor ? Tank you Denis

Dual 1Ghz processors is not the same as a single 2Ghz processor.
Also I don't believe Logic Express is written to explicitly use more than one CPU at a time - i.e. compiled specifically for dual core CPUs, all it is doing is checking the first CPU it finds and sees that it is only 1Ghz. So this message, while having nothing to with G4, is probably correct.
So yes it is very possible that you will get less than expected results. I am sure it will work for fairly simple arrangements so unles you start to do complicated effects or add lots of instruments it maybe ok. If you start to run into problems, I suggest freezing tracks.

Similar Messages

Upgrading Power Mac G4, dual 450 Mhz, to use Logic Express 8

I am actually confessing to being a windows studying pc engineer, but am also interested in macs.
My sister has just purchased the G4, 450 Mhz, (dual) i am confused on a few things and am trying to help her!
Basically can anyone help?
The problem is, does dual mean, that there's two processors (i am going to open it later when shes home from work and actually look!) and also, the 450 mhz, is dual, so is that 450 x 2 or just 450? I have looked about this site, and have noticed there is not much room to up the processor speed, but the goal is to get her processor speed up to a minimum of 1.25 Ghz.
Also, she wants to create her own music on a small budget, so cannot afford Logic Pro 7, it is installed on her machine but she has no key? (the guy she bought it from didnt say it needed one!)
So she now purchased Logic Express 8, but when trying to use it, the message is saying to the effect of not large enough processor speed. She has installed it on top of Logic 7, so both are now on there, will that matter?
Is the processor slot the same for the larger Mhz upgrades? if so, which are the best processors to use?
We have all the ram, she bought 1.5 GB, and large hdds, it is just this problem now, and she was in tears last night, due to the fact, every time she asks someone, she gets one step closer, gets hopeful, to find another hitch!
I am really sure i can get it workable for her, but need some apple expertise guys, sorry i know you dont appreciate windows users much, and i would own a mac, just when i can afford one!
All help much appreciated.
semmi

Hi-
Welcome to Discussions!
Sounds like you are dealing with a Gigabit Ethernet model of G4, equipped with dual 450mhz processors. It was a monster in it's day, and still has good use left in it. Problem is, 450mhz, even dual, isn't much by current software requirements.
http://www.everymac.com/systems/apple/powermacg4/stats/powermac_g4_450dp.html
As for Logic- version 7 would be usable on the machine as is. There is no problem with installing version 8 on the same system. It would be nice for her to be able to get the proper "key" to be able to use v.7. It would definitely be worth pursuing the issue with the seller.
And, as you know, to use v.8, you need more processor. Processors are a relatively easy upgrade. There are many options available, as well. One of the best buys (performance for the money) are 7455 based single processor upgrades from OWC or Fastmac:
http://eshop.macsales.com/item/Other%20World%20Computing/MEG42M1500/
http://store.fastmac.com/advancedsearchresult.php?keywords=agp
The following are all compatible with the dual 450 G4:
http://eshop.macsales.com/MyOWC/Upgrades.cfm?model=158&type=Processor&TI=4655&sh oupgrds=Show+Upgrades
You can check an installation video from the following:
http://eshop.macsales.com/tech_center/installation.cfm

Kontakt as plug in or standalone In Logic Express?

I run Logic Express in a Mac book with 2,4 Ghz dual core 2 and I have 2 giga ram.
I recently got Kontact, how is better to run it as a AU on every instrument track
or in a Standalone version routing the outputs to Logic.It seems to me that the CPU works alot now that I use it as AU plugin and i get lot of Audio warning that the system is overload.I dont use audio tracks only midi tracks.
Do I need more ram?
Thanks for help

Hi,
1st: upgrade to 4GB RAM for serious Kontakt usage.
2nd: The CPU usage is there wether you run standalone or plugin. But as a plugin, you can make better use of Logic's automation and these things. If you search about CPU handling in Logic, you can see how to lift some load off it when running heavy plugins. Basically, raise the buffer size and have an empty audio track selected while playing back your MIDI project to prevent CPU breakdowns. Having an active software instrument track selected puts Logic in a kind of "focused" mode where it reserves huge CPU ressources waiting for realtime processing of MIDI inputs to this software instrument. Having an empty Audio track selected makes Logics realtime processing more relaxed.
Fox

Logic Express 7.2 don't start, always hangs!

Hi,
Logic Express 7.2 and the newest GarageBand is not working with my dual 2.7 G5. Even after the migration from my dual 2.5 G5 to this computer, these apps are not running. Before on my dual 2.5 G5 I also had no luck to get these apps to work. Restart won't help, now I quit every application and always tried to start these apps, because I thought of an application conflict. But this doesn't help. Next I treid the steps provided by some users here in the forum - like deleting plist, dupliate loops and index folders. Nothing worked. Seems the apps always hang at the CoreAudio init. Someone have a advice for me?
Thx,
Marty

I had the same problem. You have an expired software synth, demo software, unsupported VST or AU or something that is causing Core Audio to not load. The offending file should be in library/application support/logic - clear out REX Shared Library, Rewire, or any third party, i.e. Native Instruments etc. software support files.
I'm not sure what was causing the hang for me as I removed a bunch of this stuff at the same time but Logic and Garageband came back after some spring cleaning.
Be patient and thorough and you'll figure it out.

Logic Express 7.2 Crossgrade Questions???

Hello,
I just picked up the Logic Express 7.2 Crossgrade and had some questions:
Being that Apple was so generous not include a single lick of paperwork (installation guide or manuals) and the Installer and Content disc are dated Jan. of 2006 (everything is almost a year old, read me's, manuals etc..) that are on the installer disc! I'm a little confused.
First: My original version of Logic Express is 7.0 and I do not have it installed on my computer (see specs below). So, will the serial # that came with my original 7.0. version work with this 7.2 crossgrade?
Second: Is the 7.2 Installer disc a full installer or will I have to run the original 7.0 disc and then run the 7.2 installer disc to upgrade the Logic Express application? Or is the 7.2 disc a full installer?
Third: Being that there are no physical manuals, etc... and as I stated above the PDF Manuals are almost a year old, where do I find all of the most current Manuals, Read Me's, etc...?
Fourth: is anyone using Logic Express 7.2 with a Digidesign Pro Tools LE system, which consists of a Digi 002 (Console) with Pro Tools LE 7.1cs10. I'm using it with a Power Mac G5 Dual-Core 2.3 with 4.5 GB of Ram, running Tiger 10.4.8 (PPC). If so, are you having any problems using Logic Express 7.2 (or what ever the current version of Logic Express is) and is having Logic Express 7.2 installed on the same computer as Pro Tools causing any problems with Pro Tools running properly (or to be blunt, breakin Pro Tools)?
P.S.
I know I might get slammed for this and I know that the Logic Express 7.2 Crossgrade was only a lousy $29.00 plus Tax but is it too much to ask for actual physical manuals, installation guides with the crossgrade? And most importantly, at least the most current version of Logic Express 7.2? As I said above, the 7.2 disc is dated almost a year ago! The current version I now see is 7.2.3 and was released September 2006. What's the deal with that?. I guess Apple is trying to save a buck or make one, who knows?
Any help would be appreciated!
Dual-Core 2.3GHz PowerPC G5 processor Mac OS X (10.4.8) 4.5 GB of Ram

Thanks for the reply SynterX,
I'm glad to see that someone is on the same wavelength as me. I agree 100 percent that Apple "could have at least supplied a single sheet of paper in there that says how to install and what to do". I happen to be one of the people that like to look at the actual printed documentation (call me crazy). And yes, I did have to send them my 7.0 Disc. Thanks for answering the mysterious full installer/serial # question that I had. Just curious, when did you get your crossgrade and is it the same version that I just received, 7.2 (which is almost a year old).
I also just ordered the Soundtrack Pro upgrade to Final Cut Studio. I can't wait to see what that mess looks like!
P.S.
Where does one find the current Logic Express Documentation, etc...?
Thanks again!
Dual-Core 2.3GHz PowerPC G5 Mac OS X (10.4.8) 4.5 GB Ram

Using the MXL USB.006 microphone with logic express 7.2.3

When I have the USB audio codec selected in logic express 7.2.3 (macbook pro, intel dual core) I cant get any sound from my speakers on the laptop, or the headphones I use with the laptop headphone jack. I can record vocals but can't hear playback. If I switch to the built-in audio driver for the macbook pro, I can hear the vocal I recorded on the MXL, but with the built-in driver selected, I can't record with the mic.
Is there a solution for this?

Hi md,
I think if you look up Aggregate device in help it's what you need. You create one in Audio MIDI set up which allows for input via the USB microphone, and output through built in audio. Then Select it in Mac Sound Preferences.
Good lck,
Ray

Question about logic pro 7 & logic express

I have been working in Logic Platinum 4.7 for several years & need to upgrade - I work mainly in MIDI for new Age music and add 1 or 2 live audio tracks - I don't use a lot of effects and never use loops - a salesman at Sweetwater suggested that I might only need logic express rather than Pro 7 - does anyone know if logic express can do all that logic 4.7 did? I particularly need to edit MIDI notes in the score format - and is it true that I dont' need a mixing board any more even though I still want to use my Kurzweil sampler, PC 88 MX and Proteus modules? Also need suggestions about audio and MIDI interfaces to use with an IMac 2.16 intel dual processor computer that I will buy at the same time - thanks for any input - jazznow
e mac Mac OS X (10.3.1)
e mac Mac OS X (10.3.1)

I have been working in Logic Platinum 4.7 for several
years & need to upgrade - I work mainly in MIDI for
new Age music and add 1 or 2 live audio tracks - I
don't use a lot of effects and never use loops - a
salesman at Sweetwater suggested that I might only
need logic express rather than Pro 7 - does anyone
know if logic express can do all that logic 4.7 did?
I particularly need to edit MIDI notes in the score
format - and is it true that I dont' need a mixing
board any more even though I still want to use my
Kurzweil sampler, PC 88 MX and Proteus modules? Also
need suggestions about audio and MIDI interfaces to
use with an IMac 2.16 intel dual processor computer
that I will buy at the same time - thanks for any
input - jazznow
I do not know about 4.7 but I do have Logic Express which
I used for about 6 months before upgrading. I would think
that you will be fine if all you are doing is what you described
here. You really dont need a mixer but you might want to
look at a control surface which gives you the feel of a mixer.
I suggest the Behringer BCF2000, Only 200 and it emulates
a Logic Control. As far as interfaces you are going to find
alot of different opinions here so you should check them
all out. It comes down to how much you are willing to spend.
Hope this helps, PK

Help Required Please with Logic Express and Yamaha O1X

Hi, I'm a new Logic and Mac user. I have just installed Logic Express and I am trying to get my Yamaha O1X mixer/ interface to work. I have the MLAN Tools installed and I can load a demo song into Logic. The meters on my Mixer are moving, I just cannot hear any sound. Doesanyone know the correct way to set this up to work correctly??
I Mac 20" Mac OS X (10.4.9) Intel Dual Core 2.46 Ghz with 2GB Ram

Answer these questions for me:
Is the Monitor A/B switch green or off?
Do you have the faders 1/2 raised on the 01X in the INST tab, and is the Stereo fader raised?
Where is your amp/speakers connected to on the O1X?
Should be connected to monitor L/R out with the A/B switch off (not green).
If you load the logic demo are the meters moving?
Is Logic selected as your DAW on the O1X utility tab?
In your AMS settings....MLAN should be selected for the inputs and outputs
Make sure you did This!!!!
To monitor your computer's audio outs via the 01X go to the surface of the 01X. In the upper right click INTERNAL MODE (2nd button from left, top of the 01x next to REMOTE).
Go to the right of the 01x there are 5 white buttons for
AUDIO/INST/MIDI/BUS/AUX/OTHER. Choose INST - bring up the faders on Channels 1 and 2. Pan them left and right by clicking PAN (one the surface of the 01X in the PAGE area once, then using the knobs beneath the green screen mLAN 1 and mLAN 2 and spinning the knobs left and right), and control your master volume with the master fader. Use the headphone volume to adjust output level.
Very important......if you did all of this, play a song from itunes see if there is audio if not you have something connected wrong.
If you get it from itunes and not logic....then we need to look at logic!
You need to run logics setup assitant and make sure in the controller setup the O1X is showing! Click rebuild defaults in the controller tab of logic....you should see the faders move!
let me know....i will stick with ya till we get it working.
Craig
email me @ [email protected]

Replacement Motherboard for Dual 1ghz MDD G4

My original motherboard for my G4 is toast.
What replacement Motherboards are compatible with my dual 1ghz
mdd G4?
The white sticker on board reads: 630T3984/630-4256
Thanks
Eric

Ouch, I was hoping it wouldn't be one of those.
I think it has to be the same. My info comes from an Apple document discussing CPU upgrades.
Wait ... quoted -
Before Replacing the Processor
Important:
Apple has determined a compatibility issue between the processor and certain
fabrication levels of the logic board on some Power Mac Server G4 (Mirrored Drive Doors)
and Power Mac G4 (Mirrored Drive Doors) products. Before ordering a replacement
processor for those models, follow these steps:
1. Open the computer and check the fabrication number that is printed on the logic
board. The fabrication number is easily visible at the edge of the board near PCI card
slot 5.
2. If the logic board fabrication number is 820-1308, 820-1440, or 820-1445, do
not
order the processor module. Instead, you must replace both the logic board and the
processor by ordering the combined module: Module Set, Logic and Processor (Apple
part number 661-3654).
Replacement Warning:
When ordering this combined module set, a returned logic
board must match one of the three fabrication numbers (820-1308, 820-1440, or 820-
1445). If the logic board does not match one of these fabrication numbers, it will be
rejected.
3. If the logic board fabrication number is any other number (
not
820-1308, 820-1440, or
820-1445), order only the multiprocessor module (Apple part number 661-2730).
So make of it what you will. If your email address is in your profile, I'll email the whole document - it's a bible for MDD owners - shows you how to remove and replace everything, with photos. It's only 3.3MB.

Sample Rate Problems going from Garage Band to Logic Express

I've downloaded the Trial Version of Logic Express. When it launched it changes the i/o sample Rate that is required by Garage Band (I'm using a digi002 i/o). The result is that garage band plays back at a fraction of it normal rate (sounds like crap).
It wasn't a problem until the trial ran out on Logic Express. I could change the sample rate back inside Logic. Hummm ... what to do? I don't see any place to change the rate in the garage band preferences or in the core audio interface. Any suggestions would be appreciated.
G4 1.25 dual, mirror Mac OS X (10.4.6)
G4 1.25 dual, mirror Mac OS X (10.3.9)
G4 1.25 dual, mirror Mac OS X (10.4.6)

I've never had any such problem with Logic Express. GB files just load up, and work fine. Did you change anything in Logic Express? There are setting for that there, but even songs I open after I changed LE to 24 bit, work fine.
Wait, are you saying LE is changing the sample rate, and then it stays that way when you open GB? Hmmm, What do you have LE set for? I think mine is set at 24/96, but I'd have to look to be sure. But I am not using the same interface as you are. It might be something you just have to live with. Have you tried posting this in the LE7 forum? Maybe one the gurus there knows what you can do.
Oh, and I am using GB 2, not GB 1, but I am not sure that is relevant.

Logic Express, Reason 4 and a MacBook Pro.

I'm looking to get a MacBook Pro (15" @ 2.4 Ghz C2D) and have been writing in Reason 4 pretty exclusively on our current project. In the past I was using Cubase SX2, Reason and a PCI Audio card. So, I'm looking to find a Intel Compatible audio application and most likely not going to get the latest version of Cubase SX (or whatever it's called now). Nice application but I'm ready to move to something else.
A couple of questions... Will logic work nicely with the MBPro? Is the 15.4" screen tolerable with Logic Express? I'll still have the Dual 1.8 G5 w/ 4 GB of memory but wan to try and be totally portable. Also, for a simple two channel input how is the quality on the 1/8" jack? Should I look for a nice 2 channel input/output USB audio card?
That is all my questions for now.
Thanks.
Bill

I may have mispoke - I need to be able to transfer pictures from my Samsung phone to my Macbook Pro - I have had them talk with the bluetooth but that only worked once. I would like to be able to use a cord and have the Macbook recognize the phone - how do I do that?

Logic express 7 compatible with Mavericks?

Will my version of LE7 work with OSX Mavericks?
Thanks in advance!

Hello FranMatt80,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Logic Express 7 - Technical Specifications
http://support.apple.com/kb/SP605
Macintosh computer with a PowerPC G4 or faster processor (G5 or dual G4 processors recommended).
Best of luck,
Mario

Logic Express - Help

Hello All --
I'm having a bit of an oddity and am looking to see what information that anyone can give me.
My configuration is simple -
Mic thru cable into Alesis multimix 12 - To this point I get a great signal and all is working as I think it should be.
Multimix out thru firewire into Mac G4 dual processor (1.25 GHz I believe w/ 1GB RAM and too much HD OS X.4.8) using Logic Express 7.2 as audio software - what reads as "0" on the multimix is -22/-244 as received by the software - basically my signal *****.
Tried using Garage Band instead - still el sucko
Tried using Steinberg Cubase LE - still el sucko
So my question is - anyone have any idea what is killing the signal? I know this is digital audio and a little different than analog - but this just seems wrong in so many ways.
I've tried many different Firewire cables and have even tried a different computer - still no levels - what gives?
Greg
many Mac OS X (10.4.8)

Hi aalkemist,
Then,pehaps,your signal needs to be amplified a little more before,reaching Logic.On the Alesis,can you turn it up more on the input? Without going over of course.
Some meters in the "real world" reflect different dB readings. I won't go inot details on that,as the vultures might descend on this...
Suffice to say,that I have one good example of hardware VS software meters.
I own a focusrite trak master preamp.The older one with LED output meter.
It is calibrated so that when the LED meter reads -18dB,I get approximately -8 dBFS on the Logic meters. dBFS means "decibels full scale" and there is no going over 0 on this scale.so when I track with this preamp,I can only have the LED meter read up to -8dB,or else it clips the input to Logic.
Now,in your case,the "real world" meters might be calibrated to a different level.
I would suggest you do the following test,to see what the levels read in the Alesis,and what they read in Logic,when feeding a known signal:
1.in logic insert a "tone generator/oscillator" plugin to a channel,and output it channel 1 only (mono out) and set the level to,say, -20dBFS
2.take a lead cable from output 1,and wire it up to another input,say input 3 on your Alesis.Make sure the input level on the alesis is not cranked up all the way,but at -0-
3.place another channel on input,with input 3.check to see what the Logic meter is telling you.If there is a difference,note it,and check the Alesis manual,to see what their reference levels are.
From this,you'll know what levels to feed the alesis,in order to get an optimal recording level,and also at what levels both the alesis box and Logic clip at.
Cheers

How to create an ABAP Query with OR logical expression in the select-where

Hi,
In trying to create an ABAP query with parameters. So it will select data where fields are equal to the parameters entered. The default logical expression is SELECT.. WHERE... AND.. However I want to have an OR logical expression instead of AND.. how can I attain this??
Please help me on this.. Points will be rewarded.
Thanks a lot.
Regards,
Question Man

Hi Bhupal, Shanthi, and Saipriya,
Thanks for your replies. But that didn't answer my question.
Bhupal,
You cannot just replace AND with OR in an ABAP QUERY. ABAP QUERY is a self generated SAP code. You'll just declare the tables, input parameters and output fields to be displayed and it will create a SAP standard code. If you'll try to change the code and replace the AND with OR in the SAP standard code, the system will require you to enter access key/object key for that particular query.
Shanthi,
Yes, that is exactly what need to have. I need to retireve DATA whenever one of the conditions was satisfied.
Saipriya,
Like what I have said, this is a standard SAP code so we can't do your suggestion.
I have already tried to insert a code in the ABAP query (there's a part there wherein you can have extra code) but that didn't work. Can anybody help me on this.
Thanks a lot.
Points will be rewarded.
Regards,
Question Man

Dynamic Logical Expressions in ABAP: IF (lt_cond)...

is it possible to have a dynamically constructured logical expression?
I have a condition I need to use in an IF, but I want to avoid hard-coding, so I dynamicallybuild it.
for a simple example:
CONCATENATE ITAB-f1
           'EQ'
           varValue
           INTO lt_cond SEPARATED BY SPACE.
IF (lt_cond).
WRITE:/ 'Success'.
ENDIF.
Is it possible to do this?
NL

I am trying to use the macro to check an IF (cond).
cond is a dynamically constructed condition.
The bold part of my code way below is my problem area.
I'm having no trouble getting COND constructed. But I am having trouble between my macro and the processing as my error always tells me I'm calling my macro without 2 actual parameters. Or when I DEFINE my macro with &1 instead of &1 &2, I get 'incorrect logical expression'.
I've read all the documentation I can find on this, but i still cannot figure out why my macro is not processing.
Code is lengthy, but if you can, please help.
I'm anticipating the output to be 'FAILURE' at this point. I just want the condition COND to be processed.
data: tabfield(20) type c,
      orcheck type I,
      cond type string.
DATA: BEGIN OF ITAB_NOTIDX OCCURS 0,
      FIELD LIKE ZDOLTARC02-SEARCHFLD,
      VALUE LIKE ZDOLTARC03-VALUE,
      STRUCTURE LIKE ZDOLTARC02-STRUCTURE,
      AOBJ LIKE ZDOLTARC02-A_OBJ,
      END OF ITAB_NOTIDX.
DATA: BEGIN OF ITAB_AOBJ OCCURS 0,
      AOBJ LIKE ZDOLTARC02-A_OBJ,
      END OF ITAB_AOBJ.
DATA: ITAB_AOBJF LIKE ITAB_AOBJ.
DATA: ITAB_NOTIDXF LIKE ITAB_NOTIDX.
DATA: varAOBJ LIKE ZDOLTARC02-A_OBJ.
ITAB_NOTIDXF-FIELD = 'LIFNR'.
ITAB_NOTIDXF-VALUE = '123'.
ITAB_NOTIDXF-STRUCTURE = 'BKPF'.
ITAB_NOTIDXF-AOBJ = 'FI_DOCUMNT'.
APPEND ITAB_NOTIDXF TO ITAB_NOTIDX.
ITAB_NOTIDXF-FIELD = 'LIFNR'.
ITAB_NOTIDXF-VALUE = 'ABC'.
ITAB_NOTIDXF-STRUCTURE = 'BKPF'.
ITAB_NOTIDXF-AOBJ = 'FI_DOCUMNT'.
APPEND ITAB_NOTIDXF TO ITAB_NOTIDX.
ITAB_NOTIDXF-FIELD = 'LIFNR'.
ITAB_NOTIDXF-VALUE = '001'.
ITAB_NOTIDXF-STRUCTURE = 'BKPF'.
ITAB_NOTIDXF-AOBJ = 'FI_DOCUMNT'.
APPEND ITAB_NOTIDXF TO ITAB_NOTIDX.
ITAB_NOTIDXF-FIELD = 'SAKNR'.
ITAB_NOTIDXF-VALUE = '111'.
ITAB_NOTIDXF-STRUCTURE = 'BSEG'.
ITAB_NOTIDXF-AOBJ = 'FI_DOCUMNT'.
APPEND ITAB_NOTIDXF TO ITAB_NOTIDX.
ITAB_NOTIDXF-FIELD = 'SAKNR'.
ITAB_NOTIDXF-VALUE = '222'.
ITAB_NOTIDXF-STRUCTURE = 'BSEG'.
ITAB_NOTIDXF-AOBJ = 'FI_DOCUMNT'.
APPEND ITAB_NOTIDXF TO ITAB_NOTIDX.
ITAB_NOTIDXF-FIELD = 'KUNNR'.
ITAB_NOTIDXF-VALUE = 'CCC'.
ITAB_NOTIDXF-STRUCTURE = 'BSEG'.
ITAB_NOTIDXF-AOBJ = 'FI_DOCUMNT'.
APPEND ITAB_NOTIDXF TO ITAB_NOTIDX.
ITAB_NOTIDXF-FIELD = 'KUNNR'.
ITAB_NOTIDXF-VALUE = 'DDD'.
ITAB_NOTIDXF-STRUCTURE = 'BSEG'.
ITAB_NOTIDXF-AOBJ = 'FI_DOCUMNT'.
APPEND ITAB_NOTIDXF TO ITAB_NOTIDX.
LOOP AT ITAB_NOTIDX.
WRITE:/ ITAB_NOTIDX-FIELD, ITAB_NOTIDX-VALUE, ITAB_NOTIDX-STRUCTURE, ITAB_NOTIDX-AOBJ.
ENDLOOP.
DATA: VARFIELDNAME LIKE ZDOLTARC02-FIELD.
CONCATENATE cond
           INTO Cond.
SORT ITAB_NOTIDX BY AOBJ FIELD.
varFieldName = Itab_NOTIDX-FIELD.
ORCHECK = 0.
ITAB_AOBJF = 'FI_DOCUMNT'.
APPEND ITAB_AOBJF TO ITAB_AOBJ.
LOOP AT ITAB_AOBJ.
   MOVE ITAB_AOBJ-AOBJ TO varAOBJ.
   WRITE:/ varAOBJ.
   LOOP AT ITAB_NOTIDX WHERE AOBJ EQ varAOBJ.
           WRITE:/ 'LOOP TEST'.
        IF ITAB_NOTIDX-FIELD EQ varFieldName.
             WRITE:/ VARFIELDNAME.
             IF ORCHECK <> 0.
             CONCATENATE cond
                            'OR'
                            INTO cond SEPARATED BY SPACE.
             ENDIF.
             CONCATENATE ITAB_NOTIDX-STRUCTURE
                    ITAB_NOTIDX-FIELD
                    INTO tabfield.
             CONCATENATE cond
                    tabfield
                    'EQ'
                    '''' ITAB_NOTIDX-value ''''
                    INTO cond SEPARATED BY SPACE.
             ORCHECK = ORCHECK + 1.
        ELSE.
            MOVE ITAB_NOTIDX-FIELD TO varFieldName.
          WRITE:/ '2', VARFIELDNAME.
            CLEAR TABFIELD.
          ORCHECK = 0.
          CONCATENATE ITAB_NOTIDX-STRUCTURE
                varFieldName
                INTO TABFIELD.
             CONCATENATE cond
                    'AND'
                    TABFIELD
                'EQ'
                '''' ITAB_NOTIDX-VALUE ''''
                    INTO cond SEPARATED BY SPACE.
                ORCHECK = ORCHECK + 1.
        ENDIF.
   ENDLOOP.
ENDLOOP.
CONCATENATE COND
            INTO COND.
write:/ COND. "constructed properly
<b>DEFINE my_dynamic_check.
if &1, &2.
write:/ 'Success'.
else.
write:/ 'Failed'.
endif.
END-OF-DEFINITION.
my_dynamic_check (cond).</b>

Logic express 8 on my dual G4 MDD

Similar Messages

Maybe you are looking for