Logic pro X 10.0.4 and EUCON problem - plug-ins name won't appear on the display of artist series

Logic pro X 10.0.4 and EUCON problem - plug-ins name won't appear on the display of artist series
I'm currently using mavericks , logic pro x 10.0.4 and eucon 3.0.1
There was a freezing problem which is now resolved by clicking the prevent app nap in the info on eucon app and all my most used apps.

Yes - it works exactly as it did in Logic 9 under ML - my problem under mavericks and pro X was sluggish updating of display - turned encoder on MC MIX and nothing happened imediately and names on MC MIX not updating properly.
I only changed app nap to off - ie ticked it on get info panel of the EUCON application and relaunched whole lot and it as worked prefectly since (fingers crossed etc)
Ian

Similar Messages

How can I use my Dx7 as a MIDI controller for Logic Pro 9? I'm using MIDI/USB cable but Dx7 doesn't appear in the 'set-up' list, what am I doing wrong?

I'm using Logic Pro 9 - 9.1.8
MacBook Pro Retina OSX 10.9.3
DX7 2 FD connected to my laptop with a MIDI/USB cable
When I click the 'scan all models' search in the 'Control Surfaces Set Up' there is no Yamaha DX7 in the list so how can I make Logic 'see' the DX7?

As Colin pointed out, you have to look first in the Audio MIDI Setup. If your MIDI Device doesn't show up there, then Logic cannot see it either (unless you are using Logic Remote on your iPad to play over Wi-Fi).
I'm curious about the "MIDI/USB cable you mention. If the DX7 has a standard 5-pin DIN MIDI out jack, then you have to connect that to a MIDI Interface first that converts the MIDI signal to send it over the USB jack out. Please note that you would see the MIDI Interface in the Audio MIDI Setup app and not the DX7 itself. Also, in Logic you would see the MIDI Interface in the Environment as a valid MIDI input device.
Hope that helps
Edgar Rothermich
http://DingDingMusic.com/Manuals/
'I may receive some form of compensation, financial or otherwise, from my recommendation or link.'

Logic pro 7 can't see my 3rd party plug-ins

I run Logic Pro 7 on an Intel Core Duo iMac and I have a few third party plug-ins (Waves NPP, Guitar Rig, Symphonic Orchestra) that I'd also like to use with logic, but it seems that logic can't find them - when I go to try and insert one on an audio channel they're just not there as an option to choose - I can only seethe plug-ins that come with logic as part of the bundle.
Any ideas how I can tell logic how to find them?
They all use to work fine when I ran Logic Express 6 on my old eMac.

Your Intel Mac runs Intel code. Before Intel Macs existed, all Macs had PPC processors, therefore all code was PPC code.
If you don't have UB versions of your software, your software is PPC code, therefore has to run in an emulation mode, which is much slower than native performance.
You should contact the manufacturers of your plugins to update to UB versions to run them on Intel Macs. Otherwise you have to run everything emulated (under "Rosetta"), which effectively means you're throwing away half (or more) of your available processor power.

Do I need Logic Pro 8.0.1 Update, and if so, how do I get it now?

Do I need Logic Pro 8.0.1 Update, and if so, how do I get it now?
Tuesday, 2008-07-29
Due to prolonged illness, I purchased the Logic Studio Upgrade version (I already had Logic Pro 7.2.3, with dongle) only last week. Logic Studio Upgrade version initially installs Logic Pro version 8.0.0. I then dutifully set out to download both the Logic Pro 8.0.1 Update and the Logic Pro 8.0.2 Update.
As of this week, all attempts and maneuvers to simply get the Logic Pro 8.0.1 Update have failed. I cannot even find it, let alone download it!
Yes, I've tried the relabeling juggling act to fool Software Update into eventually listing and providing both the Logic Pro 8.0.1 Update and the Logic Pro 8.0.2 Update—but no luck, not any longer. These moves may have worked up until relatively recently, but they do not work now, at least as of this week.
All searching of Apple's site(s) and Support pages results in nada—Apple itself no longer lists any such file/dmg/download/update anywhere! All previous links are either dead or just dump one back on to the Logic Pro 8.0.2 Update page.
(In my many searches, I noted what seemed to me to be a majority of opinion that the Logic Pro 8.0.1 Update was a dog, especially in Mac OS X Leopard 10.5.2 or 10.5.3. Many users reported crashes, panics, and.or freezes. Is this why Apple has pulled the update and rendered it extinct?)
I Googled, I Asked Why, I Cuiled—but no Logic Pro 8.0.1 Update, except as that which lurked in the murky warez waters. Still, frustrated as I was, I did even try all such I could find . . . but no third party-hosted update worked at all.
I am concerned because in all my previous experience with Apple and its applications, ample information is made readily available about the contents of any update and an explanation of its relationship to previous updates. By this latter I mean: Apple indicates that update "x" incorporates the previous updates "u" and "v"; therefore one can proceed safely to install update "x" even if one missed updates "u" and "v" or for whatever reason did not install them.
So . . . do I need Logic Pro 8.0.1 Update, if I am then going to further update with the Logic Pro 8.0.2 Update? Does Logic Pro 8.0.2 Update incorporate the changes made in Logic Pro 8.0.1 Update? Will I be missing (critically?) something(s) in Logic Pro 8.0.1 Update if I in fact do not ever get it or install it? And how would I know? Apple has not only removed the update and all traces of it, but Apple has also removed all information about Logic Pro 8.0.1 Update—it is now literally as if it never existed.
So what's a po' boy to do? Logic Pro 8.0.1 Update cannot now be found on VersionTracker or MacUpdate or anywhere else. To date, no user group or organization or educational institution or program or audio-related company posted it or archived it.
Where/how can I get a copy of the Logic Pro 8.0.1 Update?
If I can't, what do I do?
If I can't, what do I miss?
And where is Apple's support for Logic Studio/Logic Pro in all of this?
Earnestly hoping,
j.

Rodger,
Thank you for your gracious welcome . . .
and thank you for your swift response . . .
and thank you for your information (and encouragement!).
Yes, I read that too, but searched in vain for the specifity of, say, your direction:
"Go ahead and update to 8.0.2, as it contains the 8.0.1 update."
So I shall!
Again, many thanks.

Im going to buy a macbook pro 13" 1199$ Is Logic Pro Good On Him? And Other Apple Software

im going to buy a macbook pro 13" 1199$ Is Logic Pro Good On Him? And Other Apple Software
Like iWeb, iMovie, And Staffs Like That?

As a hobbyist dual core Macbook Pro 13-1nch will do fine.
For professional work, you are better off with Macbook Pro 15-inch quad core i7..
iWeb is no more available from Apple. You may have to check Amzon for it.

Just installed logic pro 7.2 cross grade and an error comes up

hi, i have a mac book pro 2.16 ghz 1 gbram i had logic pro 7.1.1 academic
and i installed logic 7.2 cross grade and now when i open logic a messege comes up that says "project manager database on disk has got wrong version. rescanning required"
then when i push ok logic unexpectedly quits. can some please help!!! thank you.
MacBookPro1,2 Mac OS X (10.4.7)

Haven't heard of this problem before, but here's a suggestion that might work.
In your ~/Library/Preferences/Logic folder you should find a folder named 'PM Data.'
Perhaps if you dragged that folder to your desktop, your problem will disappear. Here's hoping…

Do I have to pay twice if I want to install Logic Pro X on my laptop and desktop?

Do I have to pay twice if I want to install Logic Pro X on my laptop and desktop?
Thanks

If you purchase Logic Pro X, you can install it as many times as you want in all your Macs for free, always that your Macs are supported. You only have to pay the first time you download it

Hi I am attempting to use a Zed R-16 with Logic Pro 9, how can I setup a bounce for output 17-18 this is where the mixer sums (the audio outputs on the zed come through 17-18)

hi I am attempting to use a Zed R-16 with Logic Pro 9, how can I setup a bounce for output 17-18 this is where the mixer sums (the audio outputs on the zed come through 17-18)
I would like to be able to quickly bounce down my mixes, through the Zed outputs.

Pancenter...
Yes... but I have come across some setups that came with a native SL (and even one Lion!) installation.. that somehow had a corrupted or older Prokit installed for some unknown reason... and given it's a quick fix to try.. I thought I'd mention it..
I frankly don't think it is entirely a Prokit issue itself, but it wouldn't do any harm to try and install v7 just in case it is part of the problem...
+1 on the UAD stuff....
Also, at the time it crashed... according to the logs...the OP was running Ableton Live at the same time, presumably rewired with Logic... so add all that together with UAD plugins... and that's quite a load on the system...
Finally in thread 32 there is a weird exception msg relating to the Trash2 plugin.. that I haven't seen before...
Thread 32:
0   libSystem.B.dylib
0x94c29afa mach_msg_trap + 10
1   libSystem.B.dylib
0x94c2a267 mach_msg + 68
2   ...tope.audioplugins.AU.Trash2
0x667bd57a catch_exception_raise + 250
3   libSystem.B.dylib
0x94c57259 _pthread_start + 345
4   libSystem.B.dylib
0x94c570de thread_start + 34
That might be nothing... but as i said, I haven't seen that one before and given what else is going on.. it might be involved too... or nothing to do with that at all!

I have installed ACDSee Pro3 and have problem to transfer photofiles from device: I got the message; The item could not be edited because you do not have sufficent access privileges or destination volume is no longer available." What can I do?

I have installed ACDSee Pro3 and have problem to transfer photofiles from device: I got the message; The item could not be edited because you do not have sufficent access privileges or destination volume is no longer available." What can I do?

Ask the ACDSee Pro support personnel.
With iPhoto that message means the library is a referenced library (photo not copied when imported into iPhoto's structure) and the source file is not where it was when first added to the library. I don't know how ACDSee works. Does it have a referenced mode as opposed to copying photos into its structure?
OT

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect"

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect", which is Windows lingo for "missing package dependencies". All the computers at my company with 2010 loaded seem to do OK. When I do a Dependencies Walk I get missing Visual C debug dll's missing plus IEshims and wer which both have a whole tree of dependencies missing on my machine. The Windows install is the same "Windows XP version 2002 Service Pack 3" on my PC and the working PC's. So I'm thinking I have to uninstall 2011 and go back to 2010. Is this correct? Those VC debug dll's were installed on the machines with 2010 in them but were not installed in mine.
I've heard the advice to recompile the dll with debug turned off but I don't have access to the source code.
Thanks in advance.

u87 wrote:
Thanks for the reply. This at least tells me that going back to LV2010 is not likely to solve the problem. The missing dll's are:
MFC90D.dll
MSVCR90D.dll
IESHMS.dll
WER.dll
And, once again, IESHMS and WER have other dependencies. So perhaps i need to install the Visual C++ development environment.
IESHIMS.dll is an Internet Explorer DLL that gets usually delay loaded by shdocvw.dll. As delay load it can not cause DLL load errors but only runtime errors. Maybe your DLL has it as direct dependency but that is unlikely since it does not have a documented interface.
WER.dll is Windows error reporting for Vista/Win7.
MFC90D.dll is the Microsoft Foundation classes and MSVCR90D.dll is the MS C runtime library, both as debug variant.
So all the DLLs you mention are actually MS DLLs! You haven't identified the DLL that you try to access in LabVIEW that causes these error messages. IESHIMS and WER are usually delay loaded by any component that needs it and should not likely be used by non MS code.
What is the DLL you try to load into LabVIEW and by whom? Get the provider of that DLL to provide you a non Debug build of the DLL. Installing Visual C on all the machines just to make the DLL load is not a solution, besides that it is likely not legal since I doubt you have that many licenses.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

I updated to PS CC 2014 and now my plug-ins are no longer available to use. how do I get them back?

i updated from PS CC to PS CC 2014 and now my plug-ins are no longer available to use. how do I get them back? I can no longer navigate to the NIK collection, my Topaz plug-ins, etc. They still are accessible on LR, but they don't seem to now be accessible on PS CC 2014

For Topaz, cop the shortcuts from Program Files\Adobe\Adobe Photshop CC\plug-ins to the same folder in Photoshop CC 2014
I don't know about Nik
BTW What sort of pictures does a 'Photographic Psycho' take?

I paid for and downloaded a song, but it won't play saying the file could not be found. It says this even when I click on the song IN the itunes store, so I can't even listen to the sample now??

I paid for and downloaded a song, but it won't play saying the file could not be found. It says this even when I click on the song IN the itunes store, so I can't even listen to the sample now??
I haven't kept records of the songs I have paid for, and a number of songs have recently been displaying this message, making me search my computer for them. Most I have been able to find, but this one immediately "disappeared" the moment I attempted to play it after downloading...... how do I either get it back or get my money back???

How did you do this move? Unless you know what you are doing you have to move the whole, complete iTunes folder.
iTunes: How to move [or copy] your music to a new computer [or another drive] - http://support.apple.com/kb/HT4527
Quick answer if you use iTunes' default preferences settings: Copy the entire iTunes folder (and in doing so all its subfolders and files) intact to the other drive. Open iTunes and immediately hold down the Option (alt) key (shift on Windows), then guide it to the new location of the library.
Windows users see tip at: https://discussions.apple.com/message/18879381

How do I download the music from iTunes onto an old iPhone 3gs? I have reset the iPhone to factory settings and when I plug it in it wants to use the device name for my current iPhone 5 and I don't want to change anything on my old iPhone.

How do I download the music from iTunes onto an old iPhone 3gs without affecting my iPhone 5? I have reset the iPhone to factory settings and when I plug it in it wants to use the device name for my current iPhone 5 and I don't want to change anything on my current iPhone. iTunes won't let me change the device name for the 3gs. I just want to use the old iPhone like an touch.

Hi littlemansa,
If I am understanding you correctly, it sounds like you are returning to an old iPhone that has been erased and you would like to set it up as a new device without restoring from a backup which would affect the name of your iPhone, as well as the contents therein. I have an article for you that can help you set up your iPhone as a new device, and that information can be found below:
How to erase your iOS device and then set it up as a new device or restore it from backups - Apple Support
http://support.apple.com/en-us/HT4137
Basically, it seems like you may be stuck on a screen that is asking if you would like to restore your device from the backup that is filed under the name of your new iPhone, or if you would like to set up the device as a new device. I would suggest that you set it up as a new device to achieve your desired results.
Take care, and thanks for visiting the Apple Support Communities.
-Braden

Installed iTunes on my laptop Windows 7 64 bit and I now have the following problems 1) iTunes volume won't adjust with the laptop volume control, only within iTunes, 2) playback doesn't work unless I click play twice and 3) the iTunes Store won't open

Installed iTunes on my laptop Windows 7 64 bit and I now have the following problems 1) iTunes volume won't adjust with the laptop volume control, only within iTunes, 2) playback doesn't work unless I click play twice and 3) the iTunes Store won't open

Installed iTunes on my laptop Windows 7 64 bit and I now have the following problems 1) iTunes volume won't adjust with the laptop volume control, only within iTunes, 2) playback doesn't work unless I click play twice and 3) the iTunes Store won't open

HT1386 I just got an iphone 4 and when I go to sync it, it appears in the left hand column but when I click on it there is just a blank screen with the apply logo and a tiny lock.

I just got an iphone 4 and when I go to sync it, it appears in the left hand column but when I click on it there is just a blank screen with the apply logo and a tiny lock.

OK, I think I fixed it.
After trying to restore with an old backup from the phone (it estimated it would take 4 hours) I cancelled and went through the setup menus again, but set it up as a new phone. It then appeared in iTunes and I restored it from the computer, not the phone. It appears to be working, it's syncing my old apps right now.
Summary:
1. Reset settings on phone (hopefully you backed up fairly recently)
2. Set up as NEW iPhone in setup menu on phone
3. Restore from iTunes on computer when it recognizes the phone
4. Cross fingers

Logic pro X 10.0.4 and EUCON problem - plug-ins name won't appear on the display of artist series

Similar Messages

Maybe you are looking for