Logic X audiodropout with MOTU 828 X

Machine: Macbook Pro 2,5 GHz i7, 16GB Ram, 512Gb SSD. Oktober 2014
Software LOGIC X
System: Mavericks, Yosemite
Hardware: MOTU 828 X, MOTU 8pre USB
Kabel: Thunderbolt, USB
Hi, I'm experiencing audio dropout when running the setup listed above. The dropout is not reproducible - sometimes the system runs for hours without a single dropout - then again sometimes I get dropout every 5 seconds.
- before replacing my 2009 Macbook with the 2014 Macbook I connected the same MOTU hardware via USB running OS X 10.8 and everything was perfect.
- Then I upgraded to OSX 10.9 and audio dropout started happing.
- I changed to the brand-new 2014 Macbook. Same problem
- I upgraded the new Macbook to OS X 10,10. Same problem
- On the MOTU Interfaces the firmware is the latest version 1.04 and the audio driver is the latest version dating 17. October 2014
- Even with older drivers and firmware always the same problem.
- No fusion drive on my Mac
- very occasionally the dropout problem even occurs when using the the onboard sound hardware while using Logic X
Since the audio dropout problem occurred on 2 different MacBooks and only started when I upgraded from OS X 10.8 to 10.9 I guess it is a:
1. MOTU driver / firmware problem
2. LOGIC X problem
3. OSX problem
Since I need my Mac for professional audio work I  really need a solution to this problem. Even MOTU / Germany has no clue.

Hi Sascha..
I remember you.
If you have Firefox running that's another CPU hog that can cause dropouts.
I stuck with Snow Leopard and Logic 9, great combination, there will be no further Mac purchases or upgrades for me.
Also still have my quad-core 3.0gHz PC which runs Cubase 6 very well, it keeps me compatible with the University/PBS machines running Nuendo.

Similar Messages

  • Logic losing contact with MOTU 828 (Mk I)

    Ever since installing Logic 7.1, Once or twice a session, Logic stops talking to my Motu 828 (Mk I). I'll be playing something back, or getting ready to record, and the Motu just goes quiet - no signal indicators. If I restart the Motu, the sound comes back, so not the biggest problem in the world, but sure is annoying. I've gotten rid of, then re-installed the Motu drivers, and that doesn't seem to help.
    There have been a few posts about new 828s dropping out, but nothing as intermittent as this. Any ideas?
    Dual 1.25 G4   Mac OS X (10.4.3)   Logic 7.1 MOTU 828 Mk I

    I had this problem with my Motu 828 (mk I) and my previous Imac G4 (700 mhz). Sometimes it could dropout 3-4 times during a session, sometimes it did not happen for several weeks. Buying a new firewirecable instead of the one Motu supplied made the problem be less frequent.
    I came to the conclusion that it was probably a defect firewireconnection on my Imac G4.
    Since I bought my new Imac G5 in november the dropouts has disappered.
    Suggestion: test your 828 with another mac to see if the problems go away.
    /Orjan

  • Logic Pro 7 with MOTU 828 or Apogee Ensemble??

    I've been using Logic with MOTU's 828MKII interface for about 4 years now. Since couple of days go, the 828 keeps freezing. I had to turn unit off and turn it back on and it starts to work again, but freezes again couple seconds later. I've talked to MOTU guys and they told me to switch voltage back and forth and try again. Same thing.
    I finally came to 2 option.
    1. Send the unit to MOTU and get it fixed and hope to work with it without anymore problem in the future.
    2. Get the new MOTU 828MKIII
    3. Get Apogee's Ensemble audio interface. (this one is really pricey for me)
    What do you guys think?
    Should I just get 828MKii fixed or try new gears..?
    I'm a starting film/TV composer/producer and beginning to
    do quite large projects.
    My set up is
    -G5 Quad PowerPC with 2.5GB RAM
    -250GB main hardrive, 500GB second internal hardrive
    -Yamaha HS50M Speaker
    -Yamaha S90ES Synthesizer
    -Apple Cinema 23inch
    -Running Logic Pro 7 with bunch of samples
    and plug-ins in my second internal hard drive.
    Share your opinions please.
    Thanks
    Chris

    Motu use to make one of the most reliable drivers in industry. If you're happy with it and can get it fixed... so why not stick with it for a while?
    On the other hand the new Apogee's software seems to be really solid and Ensemble's converters are much better than MKII.
    So get the 828 fixed, stick with it for a while, save some cash, buy the Ensemble, dump the old 828.
    Hope that helps

  • LOGIC PRO 8 with motu 828mkII audio interface

    I have bought a MOTU 828mkII Firewire and I am using it with a Mac Pro Intel
    dual core v. 10.4.10 running Logic Pro 8.
    My mixer is a Yamaha DM-1000. I have a problem with audio.
    I have the mac going into the 828 via a firewire cable, then out of the 828 to
    the mixer using 8 channel adat lightpipe. All devices have the same 48k sampling
    rate but I can not hear a logic virtual instrument, like a piano, using the adat
    lightpipe interface. If I use the analog "main outs" on the 828 I have audio,
    but nothing comes thru the adat output. If I use another application besides Logic with the same setup, the adat connection works fine. This leads me to think the problem has to be in Logic and how it interfaces with the Motu 828mkII. I have read all manuals and can't figure
    out what's wrong. Any suggestions?
    Thank you,
    Pierre.

    Generally, outputs on audio interfaces are discreetly named. So, if your master output is set to Output 1&2, that might refer to your analog outputs. If you want to send the a different set outputs, say, a stereo pair via ADAT, you might need to send to outputs 5&6, instead of 1&2.

  • Buses seem to be off with Motu 828

    I just recently switched to Mac from a PC using Cubase. I'm using Logic now and I like the ease of the program. However one thing is driving me crazy. When I create an audio track and I set up the input to record for some reason the buses seem to be off by a pair. For instance if I set up a stereo track to record from input 1-2, I don't get a signal till I raise up bus 3-4 Then 3-4 responds to 4-5 and so on. I checked my wiring and configurations but I can't seem to figure it out. What am I missing out on? I could work around this but it's nagging the heck out of me. Any info on the matter would be greatly appreciated.

    It's difficult to be sure without doing some network packet sniffing, but if it were another app syncing, it would be an awful coincidence, since it seems to happen only while I'm in Reminders.app -- as soon as I click the home button and go back to the home screen, it stops; when I launch Reminders again, it starts again.
    Moreover, it happens when I am not in the house, which rules out iTunes syncing.
    Note that it's not the syncing spinner (i.e. two arrows chasing each other in a circle) -- it's the data access spinner (like the wait spinner in many apps and the apple.com search box).

  • Logic/Motu 828/Logic control problems!!  I'm lost!

    Hi guys,
    I have a mac pro OS 10.4.8, Logic 7.2.3, Motu 828 Mark 2, Micro Lite midi hardware, a Xio Synth and a mackie logic control. Everytime I launch my Logic my mackie does something different. Sometimes it works, sometimes it doesnt, when I go to the set up in preferences for surface control it shows me 2 logic control. So I have to delete one and then sometimes it gives me this weird cryptic coding on my audio object if I'm recording until I turn off my mackie. I dont know what to do, My xio is connected through USB...Does anybody have any idea what the problem could be?
    I would appreciate any help.
    Thank you

    Is your MIDI interface going through a hub? Is the MC on dedicated ports? Have you rebuilt defaults in the Control Surfaces submenu? Have you tried another MIDI interface? If you delete everything in Control Surface setup, does Logic automatically install the MC next time you boot Logic?

  • Logic 9 issue with original motu 828 and Snow 10.6.2 on a new imac 21.5in

    Original Motu 828 and Imac Snow 10.6.2 os. What do i do to get this motu to work with Snow on the new iMac 21.5in model. I downloaded drivers from Motu which i get crashes. I heard some people are having no problem while others like myself having problem.
    So to those who has this type of setup how did u do it.
    I uninstall driver because of crash issues. I also trash the prefs but no go.
    without the driver motu 828 doesn't crash when plugged in firewire port using cord fw 400 to fw 800 but system prefs and logic doesn't see the motu.
    Has Motu stop supporting Snow to work with the original motu 828 and Why doesnt motu answer their phone.
    I dont think i will ever buy a motu product if their phone is always busy. Dang... Cant even leave a message with motu by phone and i need my system to running.

    My Mac Pro crashes all day since i updated or installed the Motu card.
    I have qty 3, Motu 24/IO's, and 1 828mk3 and 1 896 mk3.
    I updated to snow and then downloaded and installed motu's drivers and my Mac crashes all day long.
    Left Support ticket on MOTU site and they are so lame they can
    't even answer a support ticket let alone answer the phone.
    I am hostage to a bad sompnay!. I own the PCIe 424 and all the 24/io's etc.
    Is there another company that makes 1 card that will support 80 inputs of 96kz audio? I sure need one that only takes up one PciE slot!!!
    Also if you have Ethno instruments it will crash your mac.
    Is ther a script or master un-installer so you can remove all of Motu drivers/
    Also try opening your console, and watching...it looks for a fw/usb device that is not recognized anymore. Guess MOTU wrote some good dirty code again that causes havoc on the buss!.
    ANy ideas on another audio system that is snow lepord campatible?

  • How can i use adat inputs thru my motu 828 in logic pro7

    hey guys,
    i really need help with this one. i'm new to logic and can't figure out how to use my additional inputs from adat in logic. it just shows me 12 inputs and outputs, which are just the i/o from motu 828 interface, not including the otpical once.
    thanks so much!!!!

    i have it enabled. before i was using digital performer 4.61 and i was able to see and use all of my i/o from my motu interface. as a matter of fact i still have dp on my hard drive and when it still has all the inputs there, but not in logic. i'm duing some recordings tomorrow and i need all of my inputs to be working.

  • Logic Pro 9 & Motu 828 interface problem ?

    Hi all. I am running Logic Pro 9 on my iMac with a Motu 828 mk2 audio interface connected by firewire. It used to work fine with logic but strangely i now have a problem.
    It works fine with iTunes music and listening to sounds/mp3s etc from my desktop but as soon as i boot up logic pro and try to work on a project the only sound output i get is very high pitched noises and large gaps between these noises. It wont play any sounds at all through pro even samples via the browser.
    Can anyone help or explain what maybe wrong? i havent a clue whats happened!
    Thanks in advance for any help
    Paul

    PaulDS wrote:
    It works fine with iTunes music and listening to sounds/mp3s etc from my desktop but as soon as i boot up logic pro and try to work on a project the only sound output i get is very high pitched noises and large gaps between these noises. It wont play any sounds at all through pro even samples via the browser.
    Can anyone help or explain what maybe wrong? i havent a clue whats happened!
    Paul, sounds like the MOTU needs a reset.
    - Unplug the firewire
    - press the button "setup", turn full
    - right until "factory default"
    - push select
    - confirm with "value"
    - Power Off the Interface
    - Power On The Interface
    - Reboot The Mac - Let it settle
    - Plug the Firewire Back In
    Did you do an OS upgrade with the MOTU plugged In, any time you do an OS upgrade, even if it's just an incremental one (10.8.3 to 10.8.4) unplug the MOTU, some garbage is usually sent out the firewire port during an OS upgrade.

  • Serious issues with motu interface and logic, advice?

    i use a motu 828 mk2, updated to logic pro 7 from 6, everything worked fine for awhile. Sometimes I can spend hours playing and recording software instruments before the program malfunctions. All of a sudden the audio being played becomes out of tune and crackly, fading in and out. Then the screen of the motu begins flipping out, the faders become dim and move kinda erratic and sometimes theres letters that appear NIAG. If I save and close logic, turn off the interface then back on again the problem is gone. (actually sometimes it will work fine again and others it won't. Right now for example I will use logic for a minute and then it comes back again. I keep up on all the mac and logic updates. does my computer cause the problem to the interface or vice versa. Is the interface broke? Do I have the wrong driver?( I downloaded it from motu so I don't believe thats the case). does it have to do with the way all my folders are organized on the hard drive? Has anyone ever heard of anything like this? No? who else could I ask. motu's forum wasn't much help. I almost want to call the geek squad or something like that but I thought all you could give me some ideas. thank you for reading this. I really hope someone replies, even if it's to say which set up you have that works fine, maybe I'll reconsider mine.

    Hey, thanks for the tip. Though, that didn't work. How frustrating, The same problem has occured. Today is the fourth day in a row that I can't use logic. In the past it would act up for a day two then work again. Tuesday ( tomorrow) I'm supposed to have a recording session, It doesn't look too hopeful that this issue will be resolved. Please , if anyone has another suggestion I would greatly appreciate it. Maybe some ideas to isolate the problem. does anyone out there use an mk2? I lost my install disk and downloaded the driver from motu's website, could their universal driver be the problem? I'm getting pretty burnt out with this b/s. Maybe resetting something in logic would help. Any ideas. thank you. I think any response could help.

  • MOTU 828 and Logic Express 7

    I have a MOTU 828 purchased new in early 2002. Software is Audio Desk. Two questions:
    1. Is there any reason to get Logic Express 7?
    2. Is the MOTU 828 hardware compatible with Logic Express 7 as an interface through which to plug in instruments/mics?

    The 828mk2 is a great soundcard. As for audiodesk... Here's the low down. Both Logic Express and Audio Desk are cut down applications from their 'pro' level apps which are Logic Pro and Digital Performer. I use DP for film editing, and I like it, but it is very different from Logic. I have tried using Audiodesk, and I found some of its limitations annoying after using DP. For example, it doesn't have its consolidated window which for me, and I think many others will agree, is DPs USP. Logic express is much less crippled in this way - the interface is exactly the same as Pro, and many things that Pro can do, Express can do too. There are a few very annoying omissions which is why I eventually upgraded, but Express is a great app. You might also find Audiodesks interface a little difficult at first - it's more geared towards the ProTools look of things. Then again, some people say they find Logic completely illogical. Ultimately it's entirely personal opinion, but I would go for Logic, if only for the synths and plugins. Hope this helps, and nice one for getting an awesome soundcard! Best, Fred

  • I am having trouble with Logic 7 and my Motu 828mkII

    I am running Logic Pro 7 with a MOTU 828mkII. Logic is not seeing the audio signal from any of the rear analog inputs on my 828. The 828 is receiving the signal and I have fiddled with cuemix to make sure everything is as it should be. Motu support said that it was a logic issue, in spite of that, I sent the unit back to them to fix it and it returned with the same issue, that it is working but logic is not. I am doing something wrong. . . please tell me what it is. thanks!

    What do you have selected in the drivers menu in audio hardware prefs?

  • MOTU 828 MKII input into Logic Pro

    I posted about this earlier, but I think I can simplify/clarify:
    I'm using 8 channels of ADAT pre-amp input connected to my MOTU 828 MKII.
    Cuemix (MOTU's monitoring software) shows that all inputs are functioning properly.
    But when I try to choose an input channel in Logic, I have a problem:
    All 8 channels come through inputs 13 & 14 in Logic. Logic will allow me to select inputs 13 through 20 (they're not grayed out), but there's no audio coming to inputs 15 through 20. And, yes, I'm pressing "record" to enable the track.
    I should be able to assign inputs as follows:
    ADAT 1 = Input 13
    ADAT 2 = Input 14
    ADAT 3 = Input 15
    ADAT 4 = Input 16
    ADAT 5 = Input 17
    ADAT 6 = Input 18
    ADAT 7 = Input 19
    ADAT 8 = Input 20
    Any ideas on what's happening here?

    The reason it is 2 out is because Logic doesn't recognise the names of the inputs. They are simply numbered. So, the front 2 inputs on the MOTU are inputs 1 and 2 in Logic. So the next input in Logic is 3, but the next input on the MOTU is on the back..... which (rear of MOTU) is input 1..... and on it goes.
    Logic 4, Motu (rear)2.
    This got me at first until I realised that Logics input chanels were just numbered straight through, not differentiating between front, rear, analog, ADAT etc.... I think inputs 11 to 18 in Logic correspond to ADAT 1-8 on MOTU.

  • Simultaneous multi track recording in Logic Pro7 using MOTU 828 mk2

    I would like to use the eight separate audio inputs on my MOTU 828 and connect them directly in line to eight channel strips/tracks in Logic Pro 7 v 7.2.1.  (presumably through the firewire interface).  I can't find any documentation in either the Logic or MOTU manuals to tell me how to do it.  I'm sure someone out there knows - please tell me!

    this happens to me from time to time. I have level and sound on the track, I hit record and nothing gets recorded. I have discovered this happen when I have another track selected other than the track I am recording on. This may be a bug in 7.1.1. Make sure you have the track you are recording to, highlighted (selected).

  • Logic + motu 828 + analog mixer

    So I have a Motu 828 MK1 and wanna buy a small mixer (behringer EURORACK UB802 or Tapco Mix 100 ).
    But I little confused about audio routing in Logic Express 7.2
    So signal from motu outs 1,2,3,4,5,6,7,8 will be connected to inputs 1, 2, 3/4, 5/6, 7/8 on mixer.
    And then master out from mixer will be return to motu inputs 1,2 for bouncing.
    How to setup Logic environment?
    Thanks.
    iMac 20" Core 2 Duo   Mac OS X (10.4.8)  

    Is your MIDI interface going through a hub? Is the MC on dedicated ports? Have you rebuilt defaults in the Control Surfaces submenu? Have you tried another MIDI interface? If you delete everything in Control Surface setup, does Logic automatically install the MC next time you boot Logic?

Maybe you are looking for

  • BADI for ME22n - Component Object List

    Hi , I am working with transaction ME22n. When the item category is L. The material data tab shows a button called Components (Object List). On clicking this button i am taken to another screen which has childeren material items and the related data.

  • New iPod To Share Library

    I recently acquired a new iPod. I have an iPod 30G that works great and I want to share the same library. I have gone through the information on creating a new entry for the new iPod but all my music didn't transfer. Are there comprehensive instructi

  • Can't connect to Report Server via Management Studio

    Hi, I have a local installation of SQL Server 2005 (Developer Edition) on XP Professional SP2, with Reporting Services, Integration Services, and Analysis Server installed. I can connect to Integration Services and Analysis Server via the SQL Server

  • IWeb pages on IE7

    When I create a page in iWeb 08, it seems to view perfectly in Safari and Firefox. However, whenever I try to view it in IE7, the navigation bar, blogs, videos, picture albums and every other cool stuff disappeared.

  • R3AS Equipment download not working with filter

    Hi, all I set filter equipment in r3ac1 and then I executed initial download Load Object EQUIPMENT in r3as. but occur abort EQUIPMENT in r3am1 and outbound queue MASS_CRM_CS_EQU_* and R3AD_CS_EQU_* are stop in R/3 there are entries 1. I apply Note 83