Login issue after Firmware Upgrade Ver.4.21.5 for WRT54g v2

I just updated the firmware to Ver.4.21.5. After I log in to the router, each time I change Tabs or I save a change I am prompted for the Admin password. This is annoying, but not a limiting factor for changing settings. Is there a fix for this?
Thanks

davekstl wrote:
I just updated the firmware to Ver.4.21.5. After I log in to the router, each time I change Tabs or I save a change I am prompted for the Admin password. This is annoying, but not a limiting factor for changing settings. Is there a fix for this?
Thanks
u can reset the router and reconfigure it . it should not keep on prompting anymore .
I believe that I can make it

Similar Messages

PC Suite Issues after Firmware Upgrade of N73

Hi,
A new Firmware finally became available for my N73. The version number of this firmware is 4.0735.3.0.2.
After upgrading my firmware, every time I connect my phone via bluetooth or USB i get the "The connected mobile phone does not have PC Suite support installed" message. When I try the Help -> Reinstall PC Suite Support option, nothing happens on the phone.
I am able to view my messages via Windows Explorer (but they do not appear in PC Suite below the phone image), do a sync with Microsoft Outlook, sync with Lifeblog, etc - no problems. The only thing that does not work is installing applications via the Nokia Application Installer. Whenever I try to install an application, I get an "Operation Failed" error on the PC, and nothing happens on the Phone. I have tried installing various apps (fring, snake, Conversation) but all result in the same error.
I have tried this in Windows Vista (with latest updates) and on a clean install of Windows XP SP2.
Summary of my Configuration:
Phone: N73 (RM-133)
Product Code: 0542457
Firmware: V 4.0735.3.0.2
Operating System 1: Windows Vista
PC Suite Version: 6.85.14.1
Bluetooth Stack: IVT BlueSoleil 5.0.5.178
Operating System 2: Windows XP SP2
PC Suite Version: 6.83.14.1
Bluetooth Stack: Standard Microsoft Bluetooth Stack
Has anybody experienced similar issues? Can anybody help me? Any help will be appreciated.

I have never had such issues with my N73 - same firmware on three different systems. I have upgraded the firmware 4 or 5 times. The fact that your phone refuses to install via Application Installer makes me think that there is some issue with the phone itself - corrupted temp folder or something. If the problem irritates you too much, backup the phone and do hard reset (hold *, Green key and 3 while powering on).
Ericsson T10i -> Nokia 7110 -> Siemens C45, C55, M55, M65 -> Nokia 6131, N73, N82 -> HTC Wildfire, Desire HD -> Nokia Lumia 800 -> HTC Desire X -> Lumia 820 -> Sony Xperia SP -> Lumia 925 + Sennheiser CX 500
If I've helped, use the Kudos button to thank

'Page Not Found' wifi login issue after ios6 upgrade on iPad2

After upgrading my iPad2 to ios6 and trying to connect to my wifi, my iPad2 tries to login for some reason to the Apple site but all that comes up is a 'Page Not Found' notification. I can browse the Apple site while in this browser but I can only go back, forward or cancel which then disconnects my iPad2 from my wifi.
Is there a solution to this issue? I've already tried clearing my browser history and data and resetting the iPad2 but to no avail

This one works for me...
Reset networks settings: Settings>General>Reset>Reset Network Settings

Home Hub 5 VPN issues after firmware upgrade

Hi all, hope you can help...
I use Check Point SecureClient to connect to work, it connected perfectly until this morning and it It fails with a "failed to update policy" error.
Nothing else had changed, and I could connect to my VPN using my 3G MiFi, so I checked the home hub and the firmware had been upgraded to Software version 4.7.5.1.83.8.204 yesterday evening.
I've spent all day on the phone and chat to BT, and the best they could offer was a call to the tech team who might charge me for fixing this!
Has anyone managed to get round this issue? Is it a known fault? Is a new router the best option, if so which can be configured with the minimum of guesswork?

Have you tried the VPN setting on the Homehub?
http://192.168.1.254/index.cgi?active_page=9121
If you found this post helpful, please click on the star on the left
If not, I'll try again

Crippled 192.168.1.1 page after firmware upgrade

hi,
i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

It is good to know that the issue is resolved
After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

PC-Suite sync fails after Firmware upgrade of E65

After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
- PC-Suite updated to 7.0.9.2
- Outlook 2003
- XP Prof.
Any ideas?
Solved!
Go to Solution.

The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
Does somebody has an idea?

Performance Issues after an Upgrade

Hello!
We are experiencing performance issues after we upgraded to a new version of Hyperion (11.1.2.1). At this point, I am not too sure about the actual causes for this degrade in performance but I am trying to narrow down the causes and need your inputs. Please help me with your ideas.
1) What could be the causes/factors for the performance to degrade after an upgrade?
2) Does the performance of a script depend on the user credentials i.e. who is launching the script? Whether it’s the super admin of the application/application owner or an application specific admin?
3) Does the performance of the scripts depend on the place you are launching it from? For example - will the performance differ if it’s launched from MaxL Vs EAS?
Please let me know your thoughts on this.
Thanks,
- Krrish

There are a number of bugs 12600557, 12675485, 12669814, 12698488 logged in for 11.1.2.1 - If you use Internet Explorer 8 and have data forms designed to use a large number of sparse dimension members in rows or columns, you may experience performance degradation when opening the data forms.
This has been fixed in Oracle Hyperion Planning, Fusion Edition Release 11.1.2.1 Patch Set Update (PSU): 11.1.2.1.101 which is available on My Oracle Support as Patch 12666861.
HTH-
Jasmine.

Performance issues after iOS4 upgrade

hello everyone,
I had notices few issues after I upgraded my iPhone 3GS:
1- The screen is not rotating (when reading e-mails of flipping photoes).
2- The resolustion has decreased big time after the upgrade. Now the photos are shown in less resolution and they look hazy.
3- my Ipod is not working.
4- I could not restore my device via the itune.
my big question is there a real tangible benifit for this new upgrade?
I really appreciate if you can help me soon
thanks.

There are a number of bugs 12600557, 12675485, 12669814, 12698488 logged in for 11.1.2.1 - If you use Internet Explorer 8 and have data forms designed to use a large number of sparse dimension members in rows or columns, you may experience performance degradation when opening the data forms.
This has been fixed in Oracle Hyperion Planning, Fusion Edition Release 11.1.2.1 Patch Set Update (PSU): 11.1.2.1.101 which is available on My Oracle Support as Patch 12666861.
HTH-
Jasmine.

T410i SSD user and master password problem after firmware upgrade

Hello.
I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
Previous firmware version: 1.3
Current firmware version: 1.3.3
SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

WRT54G ver.6 no WLAN after firmware upgrade

I just did a manual firmware upgrade for the router (WRT54Gv6 v1.02.2_fw)... when I went to rest it by holding down the rest button for 30 seconds, nothing appeared to happen. The light for the WLAN is now out. When I go to directly connect it to a computer, it says 'limited connectivity' local only. The Power, 1, and Internet lights still blink. I cannot access the web browser utility at 192.168.1.1 (nothing loads). Resetting still doesn't appear to do anything (lights don't flash off or change or anything)... Any ideas?

Open a DOS window and do "ping 192.168.1.1". If you get replies, there's still a chance. If it times out or any other error message then it can't be helped. If the router is less than 3 years old, call linksys for a replacement.
The box said windows xp or better... So I installed Linux!

SG300-28 switch in boot loop after firmware upgrade

After performing a firmware upgrade on an SG300-20 switch from ver 1.1.0.73 to 1.2.5.70 the switch now boots up with the following error and resets:
30-Aug-2011 10:47:33 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter %s is too long.
The attached file contains a full output of the console boot process.
I have tried loading different versions from the console, but all produce the same error.
Has any one any idea how to resolve this issue?
Thanks
Des

Hello Tom, Thanks for your reply,
I had done the process before with the 3 firmwares offered in the cisco website. I did it again, and i get a boot loop again, with following error:
%L1Mngr-F-PARAMTOOLONG: csco-sb parameter serialNo is too long.
Any ideas?
Thank you,
Nico
Console
     Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Set Terminal Baud-Rate
[5] Stack menu
[6] Back
Enter your choice or press 'ESC' to exit:
Downloading code using XMODEM.
-- Download complete --
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x6aa500 records...
Setting checksum: 0x350925f6 , Address: 0x0
OK.
Flash programming success.
Perform WARM BOOT ...
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.4 Built 08-Apr-2010 16:37:57
Networking device with Marvell ARM CPU core. 128 MByte SDRAM.
I-Cache 16 KB. D-Cache 16 KB. L2 Cache 256 KB. Cache Enabled.
MAC Address   : 58:35:d9:96:7f:5d.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-1
100%
OK
Running from RAM...
Board ID is 22
Device ID 0xdf5111ab
*** Running SW Ver. 1.2.7.76 Date 19-Jul-2012 Time 17:54:43 ***
HW version is V
Base Mac address is: 58:35:d9:96:7f:5d
Dram size is : 128M bytes
Dram first block size is : 101376K bytes
Dram first PTR is : 0x1900000
Dram second block size is : 4096K bytes
Dram second PTR is : 0x7C00000
Flash size is: 16M
19-Jul-2012 17:54:46 %CDB-I-LOADCONFIG: Loading running configuration.
19-Jul-2012 17:54:47 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
Slot 1 - SF302-08MP
Device 0: GT_98DX1005 (AlleyCat)
-- Unit Standalone                --
Tapi Version: v1.9.5
Core Version: v1.9.5
19-Jul-2012 17:55:02 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter serialNo is too l
ong.
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 1.2.7.76 (date 19-Jul-2012 time 17:54:43)
***** DEBUG *****
DEBUG LOG IS EMPTY
0x16a614
0x167054
0x6bdc18
0x490518
0x4959e4
0x495bac
0x815674
0x816b10
0x817e64
0x1d51e8
0x1cb010
0x121d3c
***************** SYSTEM RESET *****************

No power after firmware upgrade on nomad jukebox zen xtra

I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

HP 5524 Wireless does not work after firmware upgrade

HI,
I have just purchased an HP5524. After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully.
However, ever since wireless will not work. Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum. The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
Thank you

Hi,
Thank you for posting you query,
In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen instructions.
If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
(Although I am employed by HP, I am speaking for myself and not for HP)

Really big issue after last upgrade

After invoking
pacman -Syu
this morning something really strange happened : it upgraded my kernel headers and docs to kernel 2.6.35.7, but did nothing to the kernel itself. After the install of all packages, I went to the '/boot' directory and it was empty except for the 'grub' sub-directory. Since the kernel was still loaded in memory, it was only a matter of doing
pacman -S kernel26
and it installed the kernel and initramfs image. All this happened while I rebooted in console mode to uninstall gtk/gnome completely and install kde.
After that I went to check my system configuration file 'rc.conf' and guess what, it was missing too and after that I noticed that 'inittab' had also been deleted. Luckly I edited both files with vim which made backups in 'rc.conf~' and 'inittab~' respectively, so it was easy to restore both. After having a quick look at etc I decided to reboot the system(default runlevel was changed back to 5 so I could boot kde directly) but something was strange after reboot(I expected that) : nouveau framebuffer driver did not load and I never entered KDM, getting a terminal login instead. Also noticed that the PS1 variable was not set. After trying to edit my configuration files I kept getting that this was a read only file system and could do nothing until I booted with an old ubuntu livecd. After checking on 'inittab' again I noticed the following files were missing(sadly, I never edited them):
- /etc/rc.sysinit
- /etc/rc.single
- /etc/rc.multi
- /etc/rc.shutdown
Has anyone experienced this 'accident' before? If so, do you have any clue how I might recover those files? I would rather not reinstall the system.
Thanks in advance.

jonathan183 wrote:
thiago wrote:
After checking on 'inittab' again I noticed the following files were missing(sadly, I never edited them):
- /etc/rc.sysinit
- /etc/rc.single
- /etc/rc.multi
- /etc/rc.shutdown
Has anyone experienced this 'accident' before? If so, do you have any clue how I might recover those files? I would rather not reinstall the system
pacman -Qo /etc/rc.sysinit reports owned by package initscripts ... which you could re-install ... might be worth reviewing logs and see if you can figure out whats going on first though ...
Thanks, after manually installing the 'initscripts' package in '/var/cache/pacman/pkg', my system was restored. As for what happened, I believe it was some bug with pacman, as the 'initscripts' package was uninstalled after the system upgrade. That package was part of the 'base' meta package which was upgraded as a whole. After the restore I issued :
pacman -Sf initscripts
to have the package 'officially installed'.
As I stated, 'initscripts' was not the only package uninstalled after the system upgrade, kernel26 was lost too(but kernel26-docs and kernel26-headers were upgraded successfully). After the restore I tried to start kde with 'startx' and got a message stating that '/usr/bin/X' could not be found/executed. That was solved by reinstalling the 'xorg' meta package, but I believe some package of the 'xorg' group was also uninstalled after the upgrade.

Login issue after Firmware Upgrade Ver.4.21.5 for WRT54g v2

Similar Messages

Maybe you are looking for