Login page issue

Hi,
When I open a webpage , NAC login page does not display or hit. I have enabled the login page in CAM, I dont have DNS server in this setup.
Folllowing things i have done :-
      1, Trunk link to Untrusted Port of CAS allowed only Authentication vlan(eg 9)
      2, Trunk Link to Trusted Port of cas allowed only Access vlans and management Vlan of CAS.(99,218)
      3,
               eth0: IP is 10.10.10.252
                  DG:10.10.10.1(ip address of SVI218)
               eth1:-ip is 1.1.1.1
                  DG:1.1.1.2 ( there is no SVI with tis ip address)
      3, Added CAS to CAM with L2OOB Virtual Gateway and configured managed Subnet and Vlan mapping.
      4, Enabled user login page in CAM.
      5, Switch management :-SNMP configuration on CAM and Switch( working fine)
I used to type CAS management ip address in Address bar of Internet Explorer from Untrusted side, but no responds . any thing im missing ???

Dear Faisal,
many thanks for your responds
I am getting ip address from DHCP on client (authentication vlan9, access vlan99 and ip address got from dhcp is 10.10.99.11). when we assign same subnet ip address for eth0 and eth1(OOB virtual gatway), we will loose access to CAS. We can have same subnet ip addresses, if CAS in IB virtual gateway. i have configured following things in Manged subnet and Vlan mapping.
Managed subnet :-
     ip address    :10.10.99.4
     subnetmask : 255.255.255.0
     vlan             : 9
Vlan Mapping:-
       Vlan mapping is enabled
             Untrusted vlan:- 9
             Trusted Vlan :- 99
Thanks & Regards,
Fahad Salim.

Similar Messages

CE 7.11 Portal login page issue after SPS4 Update

Hi Guys,
Has anyone worked on SP stack 4 update of SAP Netweaver CE 7.11 system?
I ask this because I did this sometime back and immediately after the update, I realized that the text size, alignment, etc. of the text (Username, Password) on logon page of CE portal (http://host:port/irj) changed a lot. The text size became different and even the alignment of the text on this page changed.
But nothing else got affected inside the portal and even the login pages for NWA, Useradmin, etc. were unchanged.
It seems there was an issue with the stylesheet for that page only.
This issue is dealt with in SAP Note no. 1397747, as per which the solution is to apply the latest J2EE Apps patch on the system. But even after applying the correct patch, the issue is not yet resolved.
Has anyone who has done SPS4 update in CE 7.11 faced this issue as well?
Thanks,
Shitij

Well, after raising an OSS message with SAP, they worked on a new patch file for J2EE Applications (J2EEAPPS SPS4 patch 3) and after deploying this patch, the issue was resolved.
So if anyone else faces the same problem, please deploy the latest J2EE APPS patch file by downloading it from service marketplace.
Closing the thread now.
Regards,
Shitij

EBS 12.1.3 Login page issue or page cannot be displayed

When I try the login page using http://host.domain/OA_HTML/AppsLocalLogin.jsp or http://host.domain/OA_HTML/AppsLogin, then the browser is displaying page can not be displayed.
When I try to run AOL/J Diagnostic Tests, using http://host.domain/OA_HTML/jsp/fnd/aoljtest.jsp, then I did not find any issues.
When I try to run AOL/J Setup Test, under Verify DBC Settings, there is a WARNING: Security in database set to "SECURE". If the DBC file contains the wrong APPL_SERVER_ID, then no JDBC connections will be possible via AOL/J.
But under Verify Guest Settings, there is an ERROR saying :Failed to validate GUEST user in Profiles.
Please help what is causing the login screen not able to show up.
Thanks.
Edited by: user5618898 on Sep 29, 2012 7:43 PM

Never mind, it was a port conflict. I tried to change the http port # to default port #80 to a cloned copy. By flipping it to a different port and then run the autoconfig, resolved the issue.

Login Page issues

Hi Experts,
                   In Hybrid App Design,i am creating login page and giving the values of username and password.These username and password are from oracle ebs work flow database.
                 In SMP 2.3, function method calling is available or not,the below one is function,i got from oracle,
                                         select fnd_web_sec.validate_login('user123', 'pass123') from dual
                      with this function i want to u get output values from yes or no condition in login page.
                            yes :- it goes to next screen.
                             no :- it fails the condition.
                           can any one have the output for these function method,please let me know and get materials or links.
Thanks & Regards,
   Lokesh Reddy G.

Madhukb,
Get your users to create a icon on their page to get around this, the URL should be:
https://secure-ausomxPOD.crmondemand.com/OnDemand/logon.jsp?userid={Username}
substitute POD for your POD name and {username} for the username to appear in the login window.
This will get around the problem.
cheers
Alex

Issue in redirecting to portal page from SSO login page

HI facing issue while redirecting to portal application from SSO login page.please find below basic details
the application comprises of TAM / Apache / Weblogic, and all the request goes in the same order.
When the application is deployed as portlet, the jsp page some how hard codes the apache host name, that in turn blocks any form submit or Ajax action.
so on successful login the redirection is not happening to required portal page as it includes apache host name in the url consrtucted.
Please suggest me what are the configurations that I need to verify .
Thanks in Advance
Jetti.

If you upgrade to v7.1 you will have all those features and more - PLUS a lot of defective pieces have been fixed in 7.1

Issue with login page

Hi,
Can anyone help me with the following issue: When I try logging into the login page using the URL_*(http://hostname.domainname)*_ the page is re-directed to the same URL but with https:_ in front of the URL but the login page is not displayed/shown.
But when i remove the 's' from https:_ and press enter i get the login page.Once i Login with the credentials also it is again re-directed to the https:hostname.domainame_.
Again only if i remove the 's' from (https:hostname.domainame) and press Enter do i get the responsibility page.This is happening each and every time when i click on responsibility its re-directed to https: link and i need to remove the 's' from https and press Enter to get the responsibility displayed.
Can anyone help me out with this issue.
Apps version :11.5.10.2

Do you have SSL implemented? If not, please review the application context file for any referenced to https and change it to http then run AutoConfig and bounce the services.
Also, check if any of the profile options is set to https and change it to http -- How to Search all of the Profile Options for a Specific Value [ID 282382.1]
Thanks,
Hussein

Issue at login page using cookies

Hello all
I have some issue with my first cookies-jsp.
Basically i have a homepage and i would like it to prompt a login form in case no cookies are found, and display the userName in case a cookie is found(and stored the name)
In case the user have to log in, the data entered in the form are sent to a "Register" servlet.
I will paste both the jsp and the servlet code, in the bottom i will explain then the problem
The jsp
<body>
        <h1 align="center" style="font-style:italic; color:olive">Welcome</h1>
        <%
        Cookie[] cookies=request.getCookies();
         if(cookies==null || cookies.length==1){
        %>
        <form action="Register" method="post">
        <table cellspacing="5" border="0" align="center">
           <tr>
               <td align="right">Name:</td><td align="right"><input type="text" name="name"></td>
           </tr>
           <tr>
               <td align="right">Email:</td><td align="right"><input type="text" name="email"></td>
           </tr>
           <tr>
               <td align="right">Submit</td><td align="right"><input type="submit" value="submit"></td>
           </tr>
        </table>
        </form>
        <%
          else {
         String cookieName="userName";
         String cookieValue="";
          for(int i=0; i<cookies.length; i++){
              Cookie cookie=cookies;
if(cookieName.equals(cookie.getName())){
cookieValue=cookie.getValue();
%>
<h3 align="center" style="font-style: italic; color:#6666FF">Welcome back <%=cookieValue%></h3>
<%
%>
</body>
The servlet (the relevant part, the doPost() method):protected void doPost(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
//get the user details
String name=request.getParameter("name");
String email=request.getParameter("email");
//create the cookie and add to response
Cookie userName=new Cookie("userName",name);
userName.setPath("/");
userName.setMaxAge(60*60*24);
response.addCookie(userName);
//prepare for forwarding
String url="/home.jsp";
RequestDispatcher dispatcher=this.getServletContext().getRequestDispatcher(url);
dispatcher.forward(request,response);
The problem is that when i enter the userdetails the first time in the form (because no cookies was found), the login page with the form is redisplayed, and if i click on refresh or reclick on th submit button then the message with the name is displayed.
I dont understand this behaviour, since the amount of cookies after the first login is made will be "2", the homepage with the username should be redisplayed and not the one with the login form.
Any advice?
p.s:
the if(cookies==null || cookies.length==1){ its to prevent that the jsp will consider the JSESSIONID as "logged in" cookie
Edited by: enrico on Jan 23, 2011 10:36 PM

Turn off the cache in your browser or set an expire header in your servlet.
Also, you might want to consider using the servlet session instead of manipulating the cookie directly.

Creating Login Pages - Server Behavior Issues

Hello,
I been trying to find a solution to this problem for this
past week.
I'm having issues with creating a login page. First, I get
the page created with a username text box, password text box, save
username checkbox, etc. Next, I add the server behavior for 'User
Auth' - 'Login User'. Now..here's the problem. When I complete
that, I get this error (SEE BELOW). Somehow the server behavior
duplicates. I can't go on until I make one of them unique from the
other. I tried every which way to delete it, but I can't. Any
suggestions?
SERVER BEHAVIOR ERROR
"The server behavior panel cannot determine whether "Log In
User" or "Log In User" is applied to your page. Please select Edit
Server Behaviors and change one of the 2 behaviors to ensure that
each is uniquely identifiable."
NOTE: By using the "-" sign above the panel, I can't remove
the duplicate.
Also, when I create a login page, I do need to insert a form
first("form1") and then place the username, password, checkbox
inside that "form1" form I just created, correct?
Thanks for all your help!
Craig

GD WebDev wrote:
> Hi,
>
> I have set-up up a database based upon username,
password and security access
> level, the access level contains 3 types of groups.
group 1, group 2 and group
> 3.
>
> I've used the dreamweaver login user server behavior.
Looking at this it only
> allows you to go to one succeed page.
> Because i have got three user access levels, i'm looking
for it to send each
> set of users from each access level to three different
succeed pages.
> In other words, group 1 is sent to one succeed page,
group 2 is sent to a
> different and group 3 to another.
>
> Is there away of doing this?
>
You could do a redirect on the page that they do land on once
succeeded.
My personal preference would be to make one page, and only
show the user
groups parts of the page that they are allowed to see.
Steve

OSX login page resolution issue switching back from a mirrored TV

I have an issue on my MacBook Pro with Retina display, OS X Yosemite (10.10.2).
I use to connect an external tv via Mini DisplayPort - HDMI cable.
Everything is ok untill I switch back to the single Retina Display: the OSX login page inherit the TV resolution (Full HD) permanently.
To fix it you untill the next mirroring you have to reset the PRAM memory on startup by holding cmd (⌘) + alt (Opt) + P + R.

I've also been having this problem. My computer now consistently shuts down between 10 seconds and 2 minutes of startup. This only happens if my computer is not plugged in. (my battery has been between 70-90% the entire time.) If I keep it plugged in...no problems.
13-inch, Mid 2013 MacBook Air
1.3 Ghz Intel Core i5, 8 GB 1600 Mhz DDr3).

Apex 4.1 Login Page 101 Branching Issue

Branching Issue from P101 based upon P101_USERNAME value entered..Please Help!
I'm having the following code on Page101 main 'login' process. The goal is to go to page 100 if the user is a normal V_USER or go to page 200 if the user is V_ADMIN. For the P101_USERNAME value, I'm determining whether the user or admin variable in my login process. However, I'm NOT branching correctly to the expected page.
The function calls to determine whether V_USER or V_ADMIN work correctly in my tests outside of APEX.
To prove the following, I hard-coded the page no. to either 100 or 200 and both of them direct to the right page, upon login, in such instances. However, when I'm determining the branching path with the below function call, the branching fails and Always goes to Page 100..I'm totally perplexed. Please help.
The thread on the forums was helpful but the user who potentially got his answer didn't show the final example as to how it worked for him.
Re: Apex 4.1 Redirect after login
My login process on P101 main apex login page..
--Page101 'login' process
DECLARE
v_path VARCHAR2(40);
v_role VARCHAR2(200);
FUNCTION getUserRole RETURN VARCHAR2
IS
v_ret VARCHAR2(40);
v_user VARCHAR2(40);
BEGIN
IF v_ret IS NULL THEN
BEGIN
v_user := LTRIM(RTRIM(HTF.ESCAPE_SC(v('P101_USERNAME'))));
--//Tested these calls outside of apex and work as expected perfectly.
IF (my_pkg.is_user(v_user) = 'Y' AND my_pkg.is_admin(v_user) = 'N') THEN
v_ret := 'V_USER';
ELSIF (my_pkg.is_user(v_user) = 'N' AND my_pkg.is_admin(v_user) = 'Y') THEN
v_ret := 'V_ADMIN';
END IF;
EXCEPTION WHEN OTHERS THEN NULL;
END;
END IF;
RETURN (v_ret);
EXCEPTION WHEN OTHERS THEN RETURN v_ret;
END getUserRole;
BEGIN
--//Set page path for user/admin. if not use default page 100
v_role := getUserRole;
--//Hardcoding works as expected. but the above line getUserRole doesn't compute properly
--//The my_pkg.is_user, my_pkg.is_admin work and return values as expectd.
--//I'm not sure whether P101_USERNAME value is available or not in this main 'login' procedure on P101
--//v_role := 'V_ADMIN';
if v_role = 'V_ADMIN' then
v_path := ':200';
:APPVAR_ROLE := 'V_ADMIN';
:APPVAR_LOGIN_BRANCH := '200';
:FSP_AFTER_LOGIN_URL := NULL;
wwv_flow_custom_auth_std.login(
P_UNAME => :P101_USERNAME,
P_PASSWORD => :P101_PASSWORD,
P_SESSION_ID => v('APP_SESSION'),
P_FLOW_PAGE => :APP_ID||v_path);
elsif v_role = 'V_USER' then
v_path := ':100';
:APPVAR_ROLE := 'V_USER';
:APPVAR_LOGIN_BRANCH := '100';
:FSP_AFTER_LOGIN_URL := NULL;
wwv_flow_custom_auth_std.login(
P_UNAME => :P101_USERNAME,
P_PASSWORD => :P101_PASSWORD,
P_SESSION_ID => v('APP_SESSION'),
P_FLOW_PAGE => :APP_ID||v_path);
end if;
end;
--------------------

There is a simpler method to accomplish this.
On your home page (typically page 1) create a branch with the branch point "on load before header"
Set the action to your desired target page.
Create a condition based on your user's role .
Which I see are similar instructions to those suggested in your linked message.
Scott

Issue with adding a new value to the Default Login Page

Hopefully this is an easy one guys, I've added a select list item to the standard login page (P101) to allow the user to select a DOMAIN as well as entering their username and password.
When the next page is displayed and I try to retrieve the value held in the new field it has been cleared, but the values entered into items
P101_USERNAME and P101_PASSWORD are still present.
I can't figure out why the values held in items P101_USERNAME and P101_PASSWORD are still present but P101_DOMAIN has been cleared.
I've tried creating a value on page zero and writing the domain value to it using pl/sql and javascript but as soon as the next page is requested the value is cleared.
Any Ideas how to get around this????
Thanks in advance

I suppose your login page contains a process like this:
BEGIN
   wwv_flow_custom_auth_std.login (p_uname           => v ('P101_USERNAME'),
                                   p_password        => :p101_password,
                                   p_session_id      => v ('APP_SESSION'),
                                   p_flow_page       => :app_id || ':1'
   :t_random_number := :p101_random_number; /* this is something I added to my code */
END;Now, if you go to this page:
http://apex.oracle.com/pls/otn/f?p=31517:1
please note the random number assigned to you. Once you login, the same number will appear on the page 1 (near to the top).
So, that is how you could solve your problem.
   :t_random_numberis an application item.
Denes Kubicek
http://deneskubicek.blogspot.com/
http://www.opal-consulting.de/training
http://apex.oracle.com/pls/otn/f?p=31517:1
-------------------------------------------------------------------

Partner application configuration is missing error on SSO login page

We have APEX 3.1.2 setup as a partner application and an application within APEX setup to use SSO for authentication. Following a link to the APEX application redirects to the Single Sign-On page, as it should, but it also shows "Error: The partner application configuration is missing or expired." I type in my password and username, click the Login button, and (if I entered my username and password correctly, of course!) then the APEX application is shown. So, I cannot figure out why we're getting the no_papp_err error and I have not found any solutions to that issue on Metalink or anywhere else on the Internet. Any ideas? I'm concerned that we have a misconfiguration somewhere that is causing this error and will affect any other partner application we setup in the future.
We're on Oracle Portal 10.1.4, SSO 10.1.2, and SSL is setup on both infra and mid tiers.

Did you try checking the partner application entries on the SSO-login server page?
please login as orcladmin or some other user with membership in, i beleive, iasadmins group. verify that for this partner application, what you see here corresponds to the application URL. it looks like your login page call may have issues. so check for login url too.
also check the ORASSO.WWSSO_LS_CONFIGURATION_INFO$ for entries corresponding to Apex application.

Login Page not getting Displayed after 10.1.3 Home Upgrade in R12

Hi,
We are performing an Upgrade of 12.0.6 to 12.1.1.
We have just finished the upgrade of 10.1.3 Home to 10.1.3.4. After the successful completetion of Patchset Installation, as a part of Instance
Validation , we found that we were not able to get the R12 Login Page displayed.
On Checking the Apache Logs, The Error Message looked as below:
[Tue Jun 30 03:08:36 2009] [error] [client 159.182.123.2] [ecid: 1246345716:168.146.11.159:585784:0:2,0] File does not exist:
/u18/app/HUTLcomn/apps/HUTL_oldtut353/portal/OA_HTML/AppsLocalLogin.jsp
But AppsLocalLogin.jsp in our environment is located in the correct location
$OA_HTML
oldtut353:orapps(app):HUTL:[home/orapps] echo $OA_HTML
/u18/app/HUTLcomn/webapps/oacore/html
oldtut353:orapps(app):HUTL:[home/orapps] cd
$OA_HTML
oldtut353:orapps(app):HUTL:[u18/app/HUTLcomn/webapps/oacore/html] ls -ltr AppsLocalLogin
-rw------- 1 orapps dba 4094 Jun 16 02:03 AppsLocalLogin.jsp
It is reading the AppsLocalLogin.jsp from a non existent Location < INST_TOP>/portal/OA_HTML/AppsLocalLogin.jsp
I have run the autoconfig successfuly in all the Application Tiers and generated Product JAR Files. But still the Error Exists.
Please help to resolve this issue.

Thank You Helios.
The thread which you had mentioned in your previous reply had the similar issue which i was facing.
I moved forward with the remaining Pre-Upgrade Tasks, Applied Maintainence Pack and then completed the Post Upgrade Tasks.
I am very delighted to let you know that my Upgrade from 12.0.6 to 12.1.1 was successful. I got the feeling of GLADIATOR :) when I saw the Login Page appearing for the first
time after the Upgrade.
Thank you all for your help and Support.
Thanks,Varun

Error: Partner application configuration is missing ... on SSO login page

We have APEX 3.1.2 setup as a partner application and an application within APEX setup to use SSO for authentication. Going to the APEX application redirects to the Single Sign-On page, as it should, but it also shows "Error: The partner application configuration is missing or expired." I type in my password and username, click the Login button, and (if I entered my username and password correctly), it redirects me to the APEX application just like it should. So, I cannot figure out why we're getting the no_papp_err error and I have not found any solutions to that issue on metalink or anywhere else on the Internet. Any ideas?
We're on Oracle Portal 10.1.4, SSO 10.1.2, and SSL is setup for both.
+Closing this topic and opening it in [Oracle Application Server - General|http://forums.oracle.com/forums/thread.jspa?threadID=832022&tstart=0|New Topic]+
Edited by: oportalist on Nov 28, 2008 10:24 AM

Did you try checking the partner application entries on the SSO-login server page?
please login as orcladmin or some other user with membership in, i beleive, iasadmins group. verify that for this partner application, what you see here corresponds to the application URL. it looks like your login page call may have issues. so check for login url too.
also check the ORASSO.WWSSO_LS_CONFIGURATION_INFO$ for entries corresponding to Apex application.

Not able to access the portal login page and idenetity console page

Hi all.
I installed PS 6.1 on a new Solaris 8 Box. DNS is not configured for this box.
I use netscape browser on the solaris boz to test my installation - everything is fine
issue:
When i tried to access the amconsole or amserver/UI/Login application, it bombs with the following exception.
but i can see the default webserver page (or any static html for that matter).
any clue?
10/28/2003 03:22:22:776 PM EET: Thread[Thread-195,5,main]
ERROR: Exception occured
java.lang.Exception: Service URL not found:session
at com.iplanet.services.naming.WebtopNaming.getServiceURL(WebtopNaming.java:180)
at com.iplanet.dpro.session.Session.getSessionServiceURL(Session.java:686)
at com.iplanet.dpro.session.Session.getSessionServiceURL(Session.java:668)
at com.iplanet.dpro.session.Session.getSession(Session.java:540)
at com.iplanet.sso.providers.dpro.SSOProviderImpl.createSSOToken(SSOProviderImpl.java:73)
at com.iplanet.sso.SSOTokenManager.createSSOToken(SSOTokenManager.java:280)
at com.sun.identity.authentication.service.AuthUtils.getOrigLoginURL(AuthUtils.java:1546)
at com.sun.identity.authentication.UI.LoginViewBean.forwardTo(LoginViewBean.java:253)
at com.iplanet.jato.ApplicationServletBase.dispatchRequest(ApplicationServletBase.java:783)
at com.iplanet.jato.ApplicationServletBase.processRequest(ApplicationServletBase.java:434)
at com.iplanet.jato.ApplicationServletBase.doPost(ApplicationServletBase.java:312)
at com.iplanet.jato.ApplicationServletBase.doGet(ApplicationServletBase.java:282)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.iplanet.server.http.servlet.NSServletRunner.invokeServletService(NSServletRunner.java:919)
at com.iplanet.server.http.servlet.WebApplication.service(WebApplication.java:1061)
at com.iplanet.server.http.servlet.NSServletRunner.ServiceWebApp(NSServletRunner.java:981)

I am facing the same problem. I am using Custom Authentication module. When I access the login page for this custom authentication module I got this error. I have DNS entry and added the IP Adress in the host file too. Anyone tell us, what could be the problem?

Login page issue

Similar Messages

Maybe you are looking for