Logitech Headset 30 and Satellite 5200-903

Hello,
i want to use a logitech headset usb30, but it don't work with the Satellite 5200-903. What can i do? The operating system is Windows XP with SP2. When i connect the headset with a usb-port, it doesn't run.
Thanks for any Answer or Tip

Hello
I don`t know if there is some software that must be installed but you should check all Sounds and Audio devices properties. Please check also the Volume control if there is option mute activated.
Volume control dial at the front side of your notebook should also not be set to minimum level.

Similar Messages

  • Satellite 5200-903: Problems with Fn-F5 and middle cpad button

    Hi,
    i updated my Win XP Home to Win XP Pro and installed all the toshiba goodies from the Homepage. Two things don't work as expected though:
    * Fn-F5 doesn't cycle through the available monitors
    * the middle cpad button cannot be used as a middle mouse button
    Don't know why Fn-F5 doesn't work, all the other Fn-Keys work as expected. They show the OSD, too. Fn-F5 doesn't show the OSD and no function :/
    About the cpad button: I tried the driver from the toshiba site and from synpatics.com
    The problem is: in the control panel i can choose functions for each button. The function "middle mouse button" is available for the left and the right button, but not the middle one. And it is not recognized as middle mouse button, but as PageUp.
    Any ideas? The notebook is a Satellite 5200-903.
    Thanks for your help.
    Ataraxis
    Message was edited by: ataraxis

    Hello Ataraxis
    First of all I must tell you that Satellite 5200 is a great unit. If I found one that costs not much money I will buy it.
    To your issues:
    As far as I know if you want to use FN+F5 key combination you must install TOSHIBA Hotkey Utility for Display Devices V2.1.0.0-1. I hope that this tool is installed properly. If you want you can try to install it again.
    I am not 100% sure but I think that this small button in the middle has no the same function like middle button as a middle mouse button and it will be used to start sPad launcher. If you want you can check it in Users manuals. I didnt read it but I hope that there you can find a proper explanation about functionality of this small button.
    Good luck!

  • How to install wireless on a Satellite 5200-903?

    Due to a very bad virus I recovered Windows on a Satellite 5200-903 of a friendly businessman. But back home he saw: no wireless LAN could be used... It seems, that cause the WLAN-switch was "off" no WLAN-driver was installed/recovered...
    Now he wants to come to me again tomorrow or the day after tomorrow - and I MUST know, how to install everything until then... he also will bring me his router, so I can configure everything for him on the notebook AND router (WPA, if possible).
    But I found TWO drivers: one was a direct download of a small file of "Agere" - wlesslan-xp-7620390.zip
    The other is from "Atheros", and the download is a links to another website "Toshiba EMEA - Wireless LAN Driver Portal" http://aps2.toshiba-tro.de/wlan/?page=downloads , where I have to identify the WLAN adapter... But: on the first download-site (I mean BEFORE redirected to "Toshiba EMEA") there is at the list "Model" NOT any Satellite 5200.
    Which driver is correct? Are there different WLAN-adapters in the 5200-903 series? Is it possible to find out the adapter model BEFORE he gives me the Notebook?
    And in the list of drvers for the 5200-903 there was a download "WLAN hotkey" wlkey-xp-2003.zip ? Do I need that too? Do I need any other things?
    And does such an "older" WLAN-Access work in another way than the integrated WLAN of a centrino e.g. ? I just know how to log into a WLAN with newer notebooks: button "wireless networks" on the right buttom oft windows, then chose the WLAN name to connect and type in the key, if needed.
    Please help me, he lives 100 miles away from me and has not much time, he comes again to me just for that matter, and of course he was not amused when he returned home and couldn't connect to the internet... and he's an ABSOLUTE noob in technical things, so I cannot tell him how to do it on his own and need your help quickly.
    Thanks a lot!

    Hello Herb
    I just want to make the whole story short and simply. After installing OS install drivers for hardware components. According the notebook specification for Satellite 5200-903 it is WLAN ready model and I do not know which WLAN card is inside. You friend should have info about that.
    If there is Atheros WLAN card the right driver you can find HERE
    After driver installation install all Toshiba designed tools and utilities starting with COMMON MODULES. It must be installed at first. WLAN-hotkey utility is important because using FN+F8 key combination you can enable/disable WLAN card.
    WLAN software (Atheros WLAN client utility) is not necessary because for WLAN you can use WXP WLAN settings. You can use it if the WLAN card is activated properly.
    So I hope you will set WLAN properly and if you need more assistance please write again.
    Bye and good luck!

  • Satellite 5200-903: Display is out of order, how much costs the repair?!

    Hello Everybody.
    As I wrote in the Headline, the Display of my Notebook Satellite 5200-903 is broken. The Display:
    * Size : 15,0 ''
    * Type : SXGA+ TFT
    * Resolution : 1.400 x 1.050 pixels
    * colour depth : 16,7 Millionen
    * Lochmaske (HxV) : 0,2175 x 0,2175 mm (dont know the right english word)
    * DEdiagonal : 15,0
    * Contrast : 150:1
    * reaction time (rise/fall) : 20/30 ms
    * LCD Brightness Steps 1-8 : 6-9-14-24-41-75-130-150
    Can someone tell me what the repair roughly will cost? I'm not sure if the repair is not to expensive for the old Notebook.
    Hope you can help me. Thanks for some answer.
    My regrads
    JumpinJack
    btw: I'm sorry for my bad english

    Hi
    Well, sorry but I cant give you a proper answer for your question.
    The fact is that the notebook screen is a expensive notebook part.
    You should contact the Toshiba service partner in your country and ask him for the replacing costs.
    Furthermore I have found this page where you can find the compatible screen.
    http://www.lcds4less.com/ToshibaLaptop__Toshiba_Satellite_5200-903__laptop-screens.html

  • Satellite 5200-903: Mini PCI Card doesn`t work

    Hello,
    I am a user of an:
    Satellite 5200-903: P4-M 2.2/256+256 DDR/60GB/15T SXGA+/DVD-R-RW/nV FX 5600/cPad/WIFI ready/XP
    My computer is equipped with an Toshiba Wirless lan Mini PCI Card.
    I installed the card a few years ago - everything worked wonderfull.
    At the beginning of 2006 I installed a new operating system (XP Pro + SP1, same system as before) because it was necessary.
    I installed all driver for the W-Lan Card, obviously the card worked in the correct way (no driver incompatibility or other problems).
    But, and thats the reason of this topic here. It isn`t possible to connect my card to any Hot Spot. I tried it with 2 different access points, but the result is the same. "No connection Point found".
    Has anyone any idea what to do or in which direction I could look for the failure? Is there maybe any special Software necessary (I couldn`t remember, that in my last installation I had needed special driver or software)
    If further informations are necessary, please inform myself.
    (sorry for the terrible english, but it isnt my first language.)
    THX for your help

    Hi,
    thx for the hints. But unfortunately none of these solved my problem.
    1. I checked my device Manager, it`s shown a Toshiba Wireless LAN Mini Pci Card
    2. The device is activated, with no problems
    3. My wireless activation switch on the left notebook side is activated (led lights yellow)
    4. Pushing the Fn+F8 Button results nothing
    (wenn i press the combination during the Notebook switch is off - i got the message "wireless connection is deactivated, please activate")
    What have to happen, when pushing the Fn+F8 Button during the wireless switch is activated? Is there any message on the screen?
    Concerning the installed driver, how could I check what type of card is installed in my notebook. I know, that there a two types of driver and card existing, toshiba and atheros.
    But, if the installed driver causes no problems I guess the right driver is installed.
    Thx for any further Idea...
    C.

  • Satellite 5200-903: cooling problem error message

    few minutes after booting my Satellite 5200-903 (xp home sp1)an error message apears: "Problem with the cooling system, shut down your system and send it to the service" (it's a free translation from German..) I installed a temperature checking tool, the software shows cpu temperature of about 60C, however I do not hear the fan..
    Can someone help?

    Hi
    You have a good chance that it's only a cooling module.
    Generally such warning message appears because the CPU cooling module cannot cool the CPU properly or it doesn't work.
    However, the best way is to contact the Toshiba service partner in your country. Ask the guys for the opinion and I'm sure you will get a proper answer.
    Good luck

  • Satellite 5200-903 does not detect Wireless Adapter

    hello everybody,
    I wonder if anyone can tip me on this one...
    Since I reinstalled the OS ( have XP pro SP2 ) PC seems not detecting anymore the WIRELESS adapter in Device manager under Network Adapter.
    Also the light of the wireless switcher does not turn on anymore.
    I am also having problems to access the BIOS to check if the adapter is detected there, I do not have a Toshiba HW setup in Control Panel as indicated in the manual.
    Any suggestions?

    Hello Juliana
    The question is how did you install the OS? If you use recovery CD all tools will be installed including Toshiba HW setup. If the unit is preinstalled with Microsoft WXP CD you must install all Toshiba stuff belatedly.
    Just short explanation about WLAN card. Basically if the light of the wireless switcher does not turn on thats clearly indicate onto hardware problem. I assume that the WLAN card is defective. Check also if the card is listed in device manager.
    If you want to enter BIOS settings pres ESC button at the boot up procedure and keep it down for a few seconds.
    Bye

  • Satellite 5200-903: Can't read my burning Data-DVD

    Hallo,
    i have a problem with my DVD/CD-ROM. It can't read anymore of my Data-DVD (backups of my harddrives) , which I burned with the same. Also it can read Movie-DVDs only after I put the DVDs in and out a couple of times. It has no problems with CDs.
    Do you think it's a software or a hardware problem.
    Thanks,
    Matthias

    Hi Matthias,
    This sounbds like a possible hardware problem to me. As you know the laser has to be re-phased to handle DVDS and the allowable tolerances are much smaller. Hence your unit can handle CDs correvtly but is struggling with DVDs.
    Have you tried cleaning the lens in your DVD-ROM, this may improve the situation for you.
    Best of Luck

  • Using Logitech Headsets with Rosetta Stone on Mavericks

    Rosetta cannot find the Logitech Headset with microphone. I googled it and there was a fix using the Midi Tool in Utilities, which fixed their problem but not mine.  When I go to Preferences>Sound>Input or Output- I can choose the Logitech Headset and words spoken register on the gauge, but Rosetta does not see it.

    This is great!  I've got one follow-on problem to this, though:  My format rate seems to keep snapping back to 16000, and breaking until I go back and fix it again (32000 works fine for me).  Any idea how to twiddle things so that 32000 is the default for my device?

  • I just got a new Mac yesterday and I am trying to connect my Logitech headset for work but can't!  I plug it into the USB but nothing pops up and I can't find where I go to look to see if it's connected.  HELP!

    I just got a new Mac yesterday and I am trying to connect my Logitech headset for work but can't!  I plug it into the USB but nothing pops up and I can't find where I go to look to see if it's connected.  HELP!

    Ask the Verizon store to exchange your iPhone for a different iPhone 4.
    UPDATE - Sure, try ckuan's solution first.  Then use mine if that fails.
    Message was edited by: sberman

  • No audio from 5200-903 and 2450-101

    hi there,
    i have just purchased a echo indigo dj PCIMCA soundcard and it installed in my 5200-903 no problem and is working fine...
    http://www.echoaudio.com/Products/CardBus/IndigoDJ/index.php
    but now my onboard speakers are not working..
    i have tried everything, ie. removeing and reinstalling drivers with no success..
    thinkin this might a been a problem with this laptop i tried it in the 2450-101 laptop and it has done exactlly the same..
    on the second laptop i have formated the harddrive and reinstalled win2k, still nothing. this laptop also has XP on a duel boot, which has never had the indigo drivers installed into it..
    according to windows device manager the sound card is working correctly and there are no errors when swiching drivers in windows and various audio programs...
    i am very worried a would like some assistance if possible please..
    cheers.

    Hi,
    you wrote
    "thinkin this might a been a problem with this laptop i tried it in the 2450-101 laptop and it has done exactlly the same..!
    This is a evidence that it is not specific to one special notebook! You tested it on two different plattforms and it didn't work twice!
    I think your problem is a driver problem of the PCMCIA Sound card!
    Did you looked at the vendor HP for a updated driver version?
    Then you should contact the support echoaudio and ask for problems with notebooks and if there is a solution available!
    Bye

  • Logitech headset Skype and Mac Mini Intel

    Hi,
    I own a Powerbook G4 and a new Mac Mini Intel Duo Core.
    Both machines run the same latest OSX version 10.4.6.
    On the Mac Mini I have a problem using Skype with my Logitech Headset 350 (usb). The system does recognize the headset, but for some reason the microphone of the headset is not working. The speakers work fine. I did set the prefrences right in the Skype menu.
    But on my Powerbook G4 the headset works perfectly fine.
    Could this be an Intel issue? Maybe I a driver (can't find one on the Logitech site)? Anyone any clue?
    Thanks, Fred
    Mac Mini Intel Core Duo 1.66   Mac OS X (10.4.6)   1280 MB ram

    On the Mac Mini I have a problem using Skype with my
    Logitech Headset 350 (usb). The system does recognize
    the headset, but for some reason the microphone of
    the headset is not working. The speakers work fine. I
    did set the prefrences right in the Skype menu.
    I have the same headset and it works fine. First, directly connect it to your mini, don't use the keyboard's USB hub since it can only drive 100mA devices. Second, check that the mic is actually on (the blue LED is constantly on, not flashing).
    If it still doesn't work go to System Preferences->Sound->Input then select the "USB Headset" and speak into the mic and watch the input level meter. If necessary adjust the "Input Volume".
    Mac Mini   Mac OS X (10.4.6)   Core Duo / 2GB

  • Satellite 5200-802: Keyboard and touchpad dont work

    Hi everyone.
    I was hoping someone could help me with a problem I'm having with my Satellite 5200-802. The Keyboard will not work evn though it shows in device manager and report it as working fine. I have updated the BIOS and tried a lot of other basic stuff so any suggestions would be greatly appreciated.
    It may be worth mentioning that I also cannot get my touchpad driver to register.
    Many thanks.

    Hi
    Do you get an error message or do you have any bed signs on the screen?
    Can you use the keyboard to access the BIOS?
    If yes then the keyboard was recognized and works!
    If you cannot use the keyboard running OS then I would recommend to delete the keyboard device from the device manager and to restart the notebook.
    After new OS reboot the keyboard should be recognized again.
    But I think that you will be not able to access the BIOS.
    Due to the fact that the touchpad does not work too, I presume the hardware is faulty or there is no connection to the motherboard. Maybe a lose cable
    Maybe you should check this. But note; if you have no experience contact the notebook technicians. Bye

  • Problems with logitech headset

    Hey guys I was just playing Call of Duty 4 the other day, using my Logitech headset on Mountain Lion 10.8.3. But when I updated to 10.8.4 the sound from the game just completely stuffed up. The music is OK but all other sound is gone. The only other sound I can hear is what appears to be voice chat coming from the right headphone but it is very, incredibly soft and you an barly hear it. Although the sound is fine when I use the built-in speakers. Is there a problem with the headset or is it just the software in Call of Duty 4?

    Hi,
    As it has been so long I reread the topic.
    I am now confused though.
    In the first post you said
    ... It works fine with Skype, but when using iChat, there is no microphone pick up. I have set the audio settings to the USB headset in both the System preferences for my iMac and for the iChat preferences; ...
    From that I went on to say set the iChat bits to anything else then set System Preferences > Sound > Input and then reset iChat to the Headset Mic option.
    You then said it was the Output (incoming Audio) that you could not hear.
    I suggested the same technique be applied to the iChat Output options/System Preferences > Sound > Output with iChat again being Set "Last".
    You have replied that you have set the preferences in both places but not to the order in which you did them (this is the important bit).
    I have seen one post that suggests that Output to the Headset should be done before the Mic/Input settings but did view this with a deal of scepticism.
    Also even though you have no MIDI device can you Open Audio MIDI Set up in Applications/Utilities and see what sample rate the Headset is using for Input (Mic) and Output.
    Ideally iChat seems to prefer 44100
    You may also notice here that you have different controls over the volume.
    Is it Mic/Input (your Outgoing Audio) or Incoming Audio/Output to Headset that is the issue ?
    8:52 PM Tuesday; June 22, 2010
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
    Message was edited by: Ralph Johns (UK)

  • How to enter BIOS mode on Satellite 5200?

    Hello!
    I own a Satellite 5200-801 and Ive recently bought a new CD/DVD - rom cause the original just died. The thing is that the drive I bought is from US market and my laptop is European. So Ive double checked all the serial numbers on it and everything was correct except the manufacture serial number that I suppose makes no difference to be different.
    My problem is that when I install it the light indicator flashes normal but when it boots it shoes IDE error boot and windows doesnt see it at all. Do u know how can I enter BIOS setting to change master/slave cause I believe that there is a difference among them at this point....the original is master and the second is csel.
    Also is there a key to enter BIOS because I cant enter at all no matter key combinations. Finally if I change the reading head of the DVD/ROM and put back the original would make the change I need?
    THANKS FOR YOUR HELP!!!

    As far as I know you cannot change anything in BIOS but check it again. To enter BIOS settings press ESC button at start up.
    Good luck!

Maybe you are looking for