Logitech wireless mouse doesn't work with Linux 3.10

When I rebooted after updating to the 3.10 kernel my mouse stopped working. The cursor is displayed but it doesn't move. I downgraded back to 3.9.9-1 and it works fine again. As far as I could see it was detecting it in the dmesg output, so I'm not sure of the cause (maybe just a regression in the driver). I've never had any problems with this mouse before.
The mouse is a Logitech M515 connected wirelessly with a Logitech Unifying receiver.
This is the dmesg line (on 3.9.9):
logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
Last edited by shaurz (2013-07-25 19:20:53)

Mine works fine with Logitech Anywhere MX, never noticed any problems. Is this still an issue?
According to the bug report, Logitech Anywhere MX should be broken I guess. If you need any info dumped to figure out why it's working for some, tell me what you need.
Kernel:
Linux xarch 3.10.3-1-ARCH #1 SMP PREEMPT Fri Jul 26 11:26:59 CEST 2013 x86_64 GNU/Linux
lsusb:
Bus 007 Device 002: ID 046d:c52b Logitech, Inc. Unifying Receiver
dmesg:
[ 3.332661] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:13.0-1/input2
( I have a keyboard attached to the same unifying receiver. Paired them up using a windows laptop. Maybe that's the difference? I guess pairing hardware to the receiver using logitech software could theoretically mess with... uhm... magical internal mapping stuff that I have no idea how it works? Ok, I'll stop guessing making things up now , good luck with the bug :3 )
Last edited by whoops (2013-07-29 10:54:39)

Similar Messages

Seems RTL8192EE wireless card doesn't work with Linux 3.19

Hi all, I just fresh installed ArchLinux on my new Thinkpad T450s. The installation has been smooth enough. I can use wifi-menu on ArchISO image (which is based on kernel 3.18.6) to get my wifi connected. Everything works great. But when I reboot into the new hard disk installation, the WiFi connection always fails.
I have tried to connect manually via wpa_supplicant and dhcpcd. It didn't show any error information like driver issue or so. The problem I can see is the link is really slow: too slow to get authenticated by router. At a small chance I can connect to the WiFi but then failed to get dhcpcd work. And at a really really small chance I can get an IP from the router but the ping latency to gateway is about seconds, so I cannot visit any service via this network.
This issue happens to Linux 3.19. I have tested on 3.19.2 in core and 3.19.3 in testing.
Is there any of you have the same issue, and is there a solution for this currently?
EDIT: typo
Last edited by sunng (2015-04-02 07:16:12)

fabiopicchi wrote:
For those using kernel 4.0, the problem is partially gone. The wireless connection doesn't randomly drops and you can always connect correctly but you can get really slow speed, and sometimes all packages are lost.
Installing this new version of the driver solves the problem:
sudo git clone http://github.com/lwfinger/rtlwifi_new.git
cd ./rtlwifi_new
sudo make
sudo make install
sudo modprobe -v rtl8192ee
Yes, rtlwifi_new works for me. I do hope this can be merged into mainline some day.

I have wireless mouse does not work with boot camp

i have wireless mouse does not work with boot camp

Did you install the correct driver for your Windows version? Are you saying the mouse does not work in Windows after Windows is installed?

Satellite M40-129: PCMCIA Card doesn't work with Linux

I have D-Link DWL-G650 with Atheros Chipset which is good supported under linux (madwifi). But if I boot Linux the card is not found. I tested the card with an Fujitsu Siemens Notebook and it worked out of the box!
Any idea why it doesn't work with my M40-129 ?

Hi
Like you know Toshiba doesnt support the Linux and there are no Toshiba drivers for the Linux OS but I was able to find this useful Toshiba page about the notebook configuration with Linux:
http://newsletter.toshiba-tro.de/main/
You should check the OS machine compatibility and the other areas.
Im sure you will find many useful tips.
Good luck

Wireless mouse doesn't work after installing iTunes

New 30Gb iPod, installed iTunes v6 on 6-mos old HP laptop with docking station/wireless keyboard/mouse. All is well, updated iTunes with latest from web, loaded songs on iPod BUT now wireless mouse will not work. Reset mouse, works for a few clicks, then dies. Reset mouse again, few more clicks, then dies. Reboot without iPod connected, no iTunes up, still mouse only works for a couple clicks. Touchpad on laptop works, also so does wireless keyboard so I know transmitter is working (not battery problem). All worked fine until I started playing with options in iTunes today. I didn't uninstall iTunes yet, is that next step? Anyone else have this problem? Suggestions???

I'm pretty sure it's probably just your mouse/computer, however I would recommend uninstalling iTunes just to make sure though.

When reinstalling OS X with install disk, wireless mouse doesn't work

I have an unusual problem: My iMAC G5 hard drive died and I installed a replacement disk. Now, I am trying to reinstall OS X 10.3 with the help of my original install CDs that came with the iMAC.
Unfortunately, my wireless mighty mouse doesn't react anymore and I cannot proceed with the installation through keyboard commands alone. I get stuck at the first install window where the system asks for the operating system language.
I am clueless how to proceed since I don't have access to any utilities to test or connect the mouse because OS X is not installed yet. I tested the mouse on another Mac and it works. Any clues? Thanks for your help.

I solved my problem by using the original mouse

Wireless Music doesn't work with new software

Hello-
I can't get my wireless music to work after I update the software to the latest version. The only one that will work is when I install it from the CD. But, I would like to use the most recent version of the software. As soon as I update, the Media Server won't launch on my computer. I am using a linksys WRT54G wireless router. If I check DHCP clients, the wireless music receiver is successfully getting an IP address. I have tried all of the things that linksys suggested (disable WEP, firewall, broadcast SSID, etc...) to no avail. Has anyone gotten the latest media server software to work with WRT54G? I have tried it on both my XP and W2K machine, with the same results (doesn't work).
Thanks,
Rich

Hi Jeremy
I have the similar problem, I've installed the software on my desktop, no error messages (apart from the certificate) and everything seems to be fine. After about 2 minutes the message appears that the network is not ready and consequently the media server is not running.
Without the server running I can't setup the Network and the entire system is not working. I could ping it but that was about it.
I've reset my router, renamed the SSID, tried with and without WEP, MAC, without firewall, opened a new account on my desktop with admin rights installed the software again into a new folder - result still not working, same error message.
To make really bad, I installed it on my laptop, same procedure and it works fine! So it seem that it has nothing to do with my wireless devices or configurations, there must be a problem while setting up the software on my desktop.
I really would appreciate your help a lot!

Cheers

Balz

Is there ANY wireless mouse that will work with the iPad 2 and Apple's Wireless Keyboard?

I have the iPad 2 and Apple's Wireless Keyboard and would like to purchase a wireless mouse that will accommodate my Apple products. I do understand that Apple's Magic Mouse is not compatible with the iPad 2, but would like to hear if there is any possibility that i could use a wireless mouse with my iPad.
Thanks :)

You don't have to purchase a mouse. You already have one, it's wireless and the only one that will work on an iPad.
 Cheers, Tom

Adesso wireless mouse doesn't work in Mountain Lion.

My Bluetooth Adesso iMouse S100 doesn't work in Mountain Lion. It barely moves and constantly halts as if its driver is continuously interrupted. It is unusable. It worked beautifully in Snow Leopard.
I don't believe the problem is in the mouse, but just for completeness the batteries are full strength. The Bluetooth control panel signal strength for the mouse ranges from -50 to -48, which may be low but I'm pretty sure was the same in Snow Leopard.
Has anyone experienced and have a fix for this problem?
Thanks.

A mouse pad solved the problem. The Ikea Lack table I'm using is the source of the problem. Its table top surface is apparently scattering the mouse's laser and not reflecting it back properly. I have not experienced this problem with any other table I've used, wood, Formica, et al.

Magic mouse doesn't work with new batteries

my magic mouse green led light won't turn on after putting in new batteries. I've changed the batteries a few times with no problems, but now it won't work. Can my mouse be defective/broken only after a few months??

I have exactly the same issue. Whenever I replace the batteries in my magic mouse I have a few days of constant disconnections. At first it's very annoying and the mouse disconnects every 3 minutes or so. It reconnects automatically in about 15 seconds but it's a huge pain. After a couple of days the connection seems to smooth out and become very stable. My guess is that it is something to do with the actual BlueTooth radio and that the signal strength might actually be too high at first. One note is that I have a magic mouse that I use with an iMac and that never seems to have the trouble, but the mouse that I've used with my laptops has always had this problem even with a couple of different laptops. It might be the mouse, but it also could be that when I'm using my laptops the mouse is only a few inches from the computer, but on the desktop the mouse is probably 2 feet from the computer.
Seems like it's a radio issue to me.

Mouse doesn't work with Option boot

I have a Logitech MX-310 USB mouse and it doesn't seem to be recognized for Option-booting.
If I click on a drive icon, it does not get selected. I have tried resetting the PRAM and doing an Open firmware reset, also plugging the mouse directly into one of the built-in USB ports. No good.
The closest I can get to selecting a startup drive is to press the wheel button, which selects two drives at once...
The mouse works normally otherwise, except for one strange thing. If I set the Energy Saver prefpane to sleep the monitor after a length of time, it goes to sleep then even when I am actively using the mouse (but not the keyboard).

Hi, Dave -
Since no OS has yet been loaded when Startup Manager is open, it would appear that the source of the problem would be hardware, not software.
FWIW, did a bit of testing - although the Enter key will activate the 'do it' arrow (the right-hand, straight arrow), I could not find any key that would shift the selection of icon from one to the next.
If you have but two choices in Startup Manager, then you can switch boot volumes using a startup command other than Startup Manager - Command-Option-Shift-Delete. This instruction tells the Mac to skip the boot volume preset in PRAM (which is also the one preselected in Startup Manager), and to boot to the next bootable volume it finds. It is a one-time instruction, meaning it does not alter the boot volume setting in PRAM.

Intel Wireless Card doesn't work with Linksys?

My wired computer works great with the WRT54GX2, but my wireless cannot hold a signal for very long. Support says they can't help me because I have a Intel wireless card. Intel does not support for that card anymore and I can't see where to buy a Linksys card. Please, help.
Bonnie

check the link for the linksys retailers
Retailers
Message Edited by Maximus on 07-21-2006 05:48 PM
I do know everything, just not all at once. It's a virtual memory problem.

Wireless Mouse Doesn't Work After Waking From Sleep Mode

I have a MacBook Pro 13" 2.9 GHZ running on OSX 10.8 and when it wakes from sleep the wireless usb mouse no longer functions. I have to continually unplug then plug the mouse back in for it to work. Is there a way to solve this problem? I haven't found any definitive answers through searching the web. It's minor but irritating as I'm not fond of using the trackpad.

Would like to backtrack this discussion to
Re: iMac 2014 5K Bluetooth Trackpad Problem after sleep
Please add your system configuration and Wifi details (G, N or AC) to the mentioned thread if possible

Magic Charger Mobee for Magic Mouse doesn't work with Mac OS X lion Mountain

The Magic Charger Mobee for Magic Mouse Apple
with Mac OS X lion Mountain
makes connections overflows and stops the system work.
What could I do, other that disconnect Magic Charger?

When you say you cannot add the printer, with the Add Printer pane open, is the 6250 visible in the Default Add Printer view? If no then it could be the USB cable at fault and I suggest you try another cable.
If the printer is visible but the Mac fails to locate a driver when you select it then you may have to trash the contents of the BJPrinters folder (HD > Library > Printers > Canon) and then run the iX6250 driver installer again.

Wireless router doesn't work with Windows 8

Does anyone have experience with attempted installs of wireless routers using windows 8? I have tried to install three devices but they will not install for windows 8 and I can't find a single one that is. I don't need the internet just a router for my home wireless. Printer, mp3, etc. If you look at all of the Linksys specs online, none of them say they are compatible with windows 8 just up to 7. I have tried to install two Linksys routers and two Belkin routers and none of them will install due to windows 8 being my OS. I use a verizon hotspot for my 4g internet.

To sfd1117:
I am able to see your post in this thread: http://community.linksys.com/t5/Social-Media-Support/Facebook-com-WRT110-Internet-access-problem/m-p.... I’ve posted a reply but let me post it here:
If other devices are connecting without any problem through the router then the problem might be on the new laptop. First thing that you can try is check if the laptop can detect other wireless networks. If it can, try connecting to the other network. If it’s able to connect then it must have something to do with the wireless settings of the router. If it can’t then the problem might be on the built in wireless card of that laptop. Before calling the laptop manufacturer though, you can still try changing a setting (channel) on the router and see if the windows 8 laptop will be able to connect. For instructions, refer to this link: Changing the Wireless Channel on a Linksys Router.
By the way, what is the model number of your router?

Logitech wireless mouse doesn't work with Linux 3.10

Similar Messages

Maybe you are looking for