Long beep sound in UCS C220 Server

Hello All,
We have recently upgraded our CM server from MCS to UCS C220. All is working well since 3 weeks. However, since the past three days the UCS server is giving long beep sounds. In the CIMC console its showing as Severe Fault and in Storage Slot 1 and physical Drive 2, the status is "Foreign Configuration" and Health status is "Moderate Fault". However, when we check the status of the light on  the physical drive, its still green and not amber. So is it there a problem with the Harddrive?
Pls find the screenshot attached.

Hey there. I don't think you'll get a reply on this forum because it looks like this is a fault on the UCS server itself, and not on the Unified Communication application that runs on the UCS server. Please re-post this discussion to the board which discusses UCS servers. You'll get a reply there.

Similar Messages

  • Continuous Beep sound on UCS c220

    Hi Guys,
    We just got a new UCS c220 server, we were deploying Esxi on it and all of a sudden it started alarming a beep sound and it is continuous, there are no logs generated either CIMC nor the led indications, what might be the possible reason, an inputs would be helpful, thnx in advance
    Regards
    Krishna

    Udupi,
    As Dan stated, it might be an issue with your RAID. In the past, I have experienced similar beeping when there was an issue with the RAID group. Except for the LSI controller, I'm not aware of any other componentt that would continuously beep on the server during operation
    http://www.cisco.com/en/US/docs/unified_computing/ucs/c/sw/raid/configuration/guide/MegaRAID.html#wp1105151
    Table 5-3 gives a translation between the beep intervals and potential issues.
    If you can reboot and interogate the LSI OptionROM during POST, you may find what it is complaining about
    Table 5-3     Summary of LSI MegaRAID Card Beep Codes
    Beep Code
    LSI Firmware State
    Cause (Depending on RAID Level)
    3 seconds on, 1 second off
    SPEAKER_OFFLINE_ENTRY
    •RAID 0: One or more drives offline.
    •RAID 1: Two drives offline.
    •RAID 5: Two or more drives offline.
    •RAID 6: More than two drives offline.
    1 second on, 1 second off
    SPEAKER_DEGRADED_ENTRY
    •RAID 1: A mirrored drive failed.
    •RAID 5: One drive failed.
    •RAID 6: One or two drives failed.
    1 second on, 3 seconds off
    SPEAKER_HOTSPARE_ENTRY
    A hot spare drive has completed the rebuild process and has been brought into the array.

  • Lenovo L420 THINKPAD starts with a constant long beeping sound for atleast 1 min.

    From few days my laptop starts with a long beeping sound for atleast more than 1 min, then comes a boot order option. I have no idea whats wrong with it,last time when it happened i had to change my harddisk. Guys anyone with expert ideas please help me,and as fast possible.

    Nope. Not using a dock at all. I have to mention tho', that the machine already visited an authorized service. The motherboard was replaced, because it didn't recognise the power brick and refused to charge the laptop.
    I'm guessing they didn't put it back together properly. Since I posted I checked the cpu / gpu temps and the cpu temps rise to 80-90 C just when I do a simple operation like delete a larger folder. I tried to turn on bluetooth to copy some stuff from my phone yesterday and for some reason it acted like i pressed fn+f4.  Went to sleep. I pressed fn+f5 just for the record, but after a few times doing this, I found that no matter what fn combo I press it goes to sleep. I have to press the power button again to bring it back. Started playing piano on the rest of the keyboard and same thing. Going to sleep. The lcd went in off mode and disappeared from both the bios and device manager. I was back at square one again seeing my desktop only on the external monitor.
    I suspect the tech guys who fixed it didn't put something back right + the fact that the cpu is so hot lets me believe that the thermal paste was not applied right.
    I still don't get why all the hardware self test pass. Maybe I should do a stress test? Or should I just send it back to service?
    Lenovo Thinkpad T61 __ Lenovo Thinkpad W520

  • UCS C220 server power button turns "Amber"

    Hi All,
    We have a UCS C220 server on which we are running CUCM 9.1 and CUC 9.1 and all of a sudden the server's power button turns amber and everything goes down. We would have to physically turn on the power button and access the VMware and start all the services.
    Please advise.
    Regards
    Bhavna

    Hi, I have the same issue, I just install a new clean CUCM 9.1 and CUC 9.1 in UCS C220 with pre-installed esxi 5.1, I leave the clients site the last Friday and today say to me that the servers is down, just turn on the server and everything comes back, in the vmware logs the only error that show is "2014-05-18T15:31:00.802Z [3DAE2B90 error 'SoapAdapter.HTTPService'] HTTP Transaction failed on stream TCP(error:Transport endpoint is not connected) with error N7Vmacore15SystemExceptionE(Connection reset by peer)" but I saw that error in the log before I installed this site the last May 5, anyone have a clue of what I have to look. Of if this error could do a crash or reset in the system.
    Thanks in advance.
    Cesar

  • Long beeping sounds during iPhone 4s calls

    Often when I am on calls longer than 5 minutes I hear a long beeping sound, almost like someone is pushing a button.  Does anyone why this is happening and how to fix it I have a 4s?

    Is this with all calls when using a headset or just some?
    If some perhaps there's a second call trying to get through & it's notifying you there's another call waiting or if it's a Bluetooth headset maybe it's telling that it requires charging.

  • How to disable a CPU on a UCS C220 server

    Hello Experts ,
    Would anybody help if there is a way to disaable a CPU on a UCS C220 server ?
    Is there a jumper that is used for this purpose ?!!
    ASAP
    Thanks guys

    Short of removing the physical CPU I don't believe there's any other way to "disable" it.  Removing the CPU will also render it's memory banks (usualyl 1/2 the DIMMs) inaccessible to the system.
    What reason to have for requiring to disable it?
    Regards,
    Robert

  • Unable to find ctrl+H message in UCS C220 Server

    Hi,
    I am unable find Ctrl +H message at the time of booting to get enter in Webbios.
    Please help me.
    Hardware: UCS RAID SAS 2008M-8i
    Rgds,
    Sambhab

    What firmware are you running on this server?
    Did you buy this raid controller direclty from cisco or from a partner.
    Based on the screenshot you provided the firmware on your controller looks very old,  I recommend that you use the HUU to upgrade the firmware of the adapter to the same level as  your server. Use link below to download the firmware package for your server.
    Cisco UCS C220 M3 Rack Server Software
    http://software.cisco.com/download/release.html?mdfid=284296253&flowid=31742&softwareid=283850974&release=1.5%283d%29&relind=AVAILABLE&rellifecycle=&reltype=latest
    Example Video of firmware upgrade.
    http://www.youtube.com/watch?v=qRahHRja15M

  • Long beeping sound

    While talking on the phone with a iPhone 5s user (only happens with this person) I occasionally hear a beeping sound it's not a quick beep it's a long continuing beeping noise that stops it's not a certain time limit either. It happens with and without earphones at one point the sound got so loud that I had to jerk my earphones out of my ear because it hurt so badly. I asked the other person if it was them or could they hear it (thinkiń they were joking with me) but they said no and I trust this person (significant other) i so not know where this sound is coming from but I do need help about it if you have and idea that would be great! Thanks
             Michael Bartley
            iPhone user! :)

    Northshore357:
    Boot from the Apple Hardware Test disk and run all tests in a loop by holding down Ctrl + L during the tests. Let it run for a while as it sometimes can take hours for an intermittent issue to show up.
    cornelius

  • UCS c220 giving long beeps, Hardisk replaced, but status still Unconfigured

    Hello All,
    We have installed a brand new UCS Server for CUCM 10.5 a couple of weeks back. Recently the UCS Server started giving long beep sounds.
    When we check through CIMC we found that the status of the Physical Drive 2 was showing “Foreign Config.” And the health as “Moderate Fault”.
    We have two Hardisks in RAID 0 group and one of those is Physical Drive 2 which has the problem. Pls find the attachment  “Physical Drive 1" and "Virtual Drive 1”.
    We have raised support request with Cisco and successfully replaced the problematic Hardisk yesterday.
    However, the status of the Physical Hardisk  is showing “Un Configured” but the Health status is “Good”.
    The Virtual Drive Info tab the status is still “Severe Fault”  and the Hard drive is showing as “Missing”
    The long beep sound is still there. Pls find the attachment “Physical Drive 2" and "Virtual Drive 2”. for more information.
    Need your help to bring this Hardisk Online from UnConfigured. Do I need to Initialize the Hardisk for inclusion in RAID0?

    Hello Keny,
    Thanks for the reply.
    I shutdown the server and configured Raid 1 through CIMC as the boot drive for VMware and installed VMware and mapped the server from Raid 5  The problem is now fixed.
    Thank you,
    Ifthiquar

  • Long Beep and autotype key

    I have HP Envy 4, Long beep sound while starting up and in password it autotype.

    Yes, I can see that now..
    Iwe plugged the 4-pinned square plug into the JPW and also unplugged the CD-rom and HD just in case.
    But I just tried it, and I still get a loud beeping sound that wont stop (until I turn it off) and a blank screen..
    All Iwe got connected now is the JPW(4-pin square), JPWR(normal 4-pin) and ATX1(24-pin)
    Thanks for the tip, sadly it wasnt enough :P..

  • Kernel panic with 1 long beep, need suggestions and helps on iMac 21.5

    First of all, my iMac spec is as follows.
    - iMac 21.5 inches Mid 2011 (Intel Core i5 2.5 Ghz)
    - OS X version 10.7.4
    - Memory 4 GB
    My situation is that I experienced a first ever kernel panic. It forces me to restart the system. I followed that, and then whenever it boots up a one time long beep sound occurs. After that a flickering screen (white and black) with normal chime sound occurs, and repeat itself for 3-4 times before actually goes into a normal login screen.
    Everything is normal, I can use any programs properly. But one thing I notice is that "serial number" is missing in "About this mac" option. I strongly remember that it's there since a time of purchase this iMac. I also take a look at System/Profiles and nothing there as well.
    I also take a look at the kernal panic log in /Library/Logs/CrashReporter and /Library/Logs/DiagnosticReports but can't find any relevant logs. There's just one file inside both 2 folders, and that log is dated which is not match to my incidence.
    I tried remove out ram, and switch the slot between them, but it doesn't help.
    Also I've tried reseting PRAM, but it doesn't help as well.
    My iMac is within the warranty but outside of technical call.
    Any suggestions and help would be very appreciated.

    Contact Apple's Express Lane.
    https://expresslane.apple.com/GetproductgroupList.action;jsessionid=KBdzQtTcydQS lvbJ6nthmsggQLWRJrXGh4phn9hb9vZNwqD0hJzp!-949435192

  • Awful beeping sound on boot

    I formated the entire hard drive and installed Ubuntu 14.04 in a Macbook 5.2.
    Ubuntu boots decently fast, however there is a disconcerting garbled image on screen:
    After that Ubuntu runs fairly well but once I restart the machine a long beeping sound takes place instead of booting, the laptop remains with power but nothing will happen after that.
    I have to manually shut down the laptop and restart, Ubuntu will load but the next restart will have the same beeping sound of death.
    I already flushed the PRAM with hotkeys and by removed the Battery several times.
    Nothing has fixed this problem, and I'm unable to install Mac OS X to troubleshoot it.
    Note: This problem appeared right after installing Ubuntu for the first time, I already formated and installed several other Distros and the beep remains.
    What can I do to fix this?

    Perhaps it is because Apple make the kernel drivers that 'help' users by beeping when the hardware is having issues? It's still unclear to me if the sound is coming from the speakers, connect some headphones to see if that redirects the sound.
    Other OS's don't always access every hardware feature so they may not make the same checks as Apple software.
    I wonder if the display has a sensor for reading the backlight output. When it is found to be off the OS may ring the alarm?
    What point does the beeping begin?
    If you can get into verbose mode you may be able to see some error messages. This is easiest if you have a bootable OS X disk. The nvram command can also be used to set the verbose mode in the settings to force verbose mode on every boot - but it can be difficult to do if you have no active OS X installation available.
    How to Reset NVRAM on your Mac - Apple Support
    Mac OS X: How to start up in single-user or verbose mode - Apple Support
    http://osxdaily.com/2007/03/25/always-boot-mac-os-x-in-verbose-mode/
    https://developer.apple.com/library/mac/documentation/Darwin/Reference/ManPages/ man8/nvram.8.html
    It seems odd to me that the boot picker seems to show a fully illuminated screen, perhaps that is driving the inverter differently? Is that always correctly displayed?
    Please provide some info on the other equipment you have access to, it could help you jump into some testing instead of discussing hypothetical problems.
    NOTE: This is speculation on my part, Apple engineers will have access to troubleshooting manuals - do you have access to an Apple store or service center - is that an option for you? They may be able to say categorically what the sound means if you are lucky.

  • Long beeps, no signal?

    Well, first off my new computer worked great for about 6 hours, and then i turned it off. the next morning, i was using it and then i tried to run Counterstrike source for the first time since i got it working. i played regular counterstrike on it fine and it worked great, but as i tried to get source to work, it reached the mainpage for Source and then the computer restarted. I tried it again just to be sure and sure enough, it restarted. so i thought that i wouldnt do that again, and i was going to just play regular counterstrike because i already knew that worked. i didnt even get to click the icon yet and the computer restarts, but this time when it restarted, nothing showed up on the moniter. the moniter's power button stayed yellow, or the standby color. the PC would run but nothing would show up. at first i thought it was the moniter, so i tried the moniter on another computer and it worked, so it wasnt the moniter. i thought it was the video card, so i RMA'd it and got a new one, thinking the old one was a defect. i stuck in the new one and it still did the same thing, so i was guessing that couldnt be the problem. everything else works, and the MSI mobo makes long beeping sounds, long continuous beeps. i tried resetting the cmos with the jumpers, and that still wouldnt work. i tried to unplug and replug the wires and that didnt work.
    does anyone have a suggestion of what i could do?

    Quote
    i dont think its the ram because i tried it in different slots and it worked in other computers.
    sometimes memory will work great in some boards, and then just not like another type. nforce are used to be the worst culprits, but now with A64 the memory controller is in the CPU, so was it another A64 system you tried your memory in?
    you've tried your RAM in another computer, so why not try some RAM out of another computer in yours?

  • UCS c240 M3 beeping sound

    I have recently installed ESXi 5.0 on the UCS C240 M3 using RAID1 as shown in the image above and it was working fine. but now am getting continues beeping sound from the server and one of the HDD is showing orange light, I tried to replace the drive the problem is still there. what coud be the casue and can any1 please give me a solution to it.

    The RAID Controller has detected a Degraded Virtual Drive. The orange light indicates the RAID-set is rebuilding.  Use "storcli" for example to check this: "
    /opt/MegaRAID/storcli/storcli64 /c0 show
    Dgrd and Rbld should be seen in the output somewhere.
    The beep is turnded on by the Controller.
    /opt/MegaRAID/storcli/storcli64 /c0 show alarm
    Ctrl_Prop Value
    Alarm     ON   
    Use
    /opt/MegaRAID/storcli/storcli64 /c0 set alarm=silence
    to turn it off.
    Alain

  • Problem with the new server UCS C220 for set IP to CIMC

    Hi
    We’ve a problem with the new server UCS C220.
    We bought two servers UCS C220 M3 for CallManager 8.6 with High Availability.
    When we turn on the server during the boot and when it tells us, oppress F8 to enter at the CIMC and set the IP. But it never enters at the CIMC.
    Then, we configure our DHCP server and our switch, we connect the three gigabyte ports to our switch to give him an IP to the CIMC, so and then can enter via browser, but neither works.
    Note. The dedicated management NIC does not link, the other two ports do make link.
    What do you suggest to put an IP to CIMC and start installing our applications?
    regards

    You may have noticed that there is no DVD rom on the c220. What you need to do is:
    Login into the CIMC from your browser
    Luanch the KVM
    Insert the VMware DVD in your machines drive
    On the KVM pop up there should be a tab to mount the drive, after mounting it click on Macros and choose ctrl_alt+delete to restart.
    After the VMware OS installs press F2 to enter IP.
    Browse to the VMware ip to download the Vsphere client
    Open the Vsphere client, enter the ip of the vmware and the username will be root and no password if you did not set one.
    You can now upload OVA templates or manually create virtua machine from this enviroment.
    Hope this help

Maybe you are looking for