Long short short beep code then no boot when trying to reboot???
I recently ran the recovery CD to get it back to factory condition and the same problems persisted (that I'll describe below) which indicates to me that there's some hardware issue. I've had the same issues before and after recovery was run.
When I start it, it often starts just fine as long as it hasn't been on for at least an hour. It seems to have memory management issues. It hangs up, gets bogged down easily, hangs, crashes, etc. It also seems to run hot. There are quite a few programs that I was able to run when it was working well that it no longer tollerates.
If I reboot after it's been running for a while It makes three beeps (Long short short). The screen goes black, the hard drive spins a little, but that's it. I have to turn it off for about an hour or two before it will actually start up at that point. Keep in mind, it doesn't start out at 100% and deteriorate. It starts out at about 40% of what it used to do and deteriorates from there. In needs to be rebooted about once a day.
Sometimes if it's hibernating, it will make the same beep code when I wake it up (Long short short) and most of the time it won't wake up from there.
So, can anyone tell me what that beep code refers to?
Has anyone else experienced similar problems?
Does anyone know which part is bad and if it's worth trying to fix it?
Thanks!
I am having the same problem....i do believe its a memory problem..??
Similar Messages
-
R7850 PE 2GD5/OC causes 1-long-2-short beep code on 990FXA-GD80 on some startups
Sometimes (usually after the desktop is shut off for a while), my GD80 board will do the 1-long-2-short beep code, and then continue booting, but the monitor display isn't activated.
Shutting down and turning it right back on however has no beep codes, and the display turns on as-expected. Turning the system off and unplugging the power for a bit, then plugging it back in also doesn't result in beep codes and the display works.
So basically, there's some GPU-related issue that seems to only affect a cold start, but not entirely sure what. According to this, the beep code is a "Monitor or display card error".
The GPU itself seems to work fine with a stress test under Linux.I RMA'd the card already, so I just hope a replacement fixes the issue.
I'm not too certain how frequently it occurs or the exact ways to reproduce it, but the issue seems to only occur on a cold start. So if I shut my computer down, sleep for some hours, and come back to turn it on, the issue occurs (where the GPU doesn't seem to come on with POST, motherboard beeps, no display output).
It happened since the first time I started using the hardware (I haven't used the motherboard or GPU previously; was waiting on a CPU). The GPU was a RMA already from MSI.
Couldn't test the components in another system. However, I'm using an old Radeon HD 2400 PRO currently in this computer and it starts up fine from cold starts.
The GPU had some other weird issues with it (hard-locked the system when the screen suspended, and wouldn't work with a UEFI VBIOS), so I'm thinking it was just faulty. On the other hand though, once the computer was on and the GPU actually running, everything else was fine (stress testing and games were fine). -
Exit code 20 error message when trying to install Master Collection 5.5. Please assist.
I get Exit code 20 error message when trying to install Master Collection 5.5. Please assist.
Installation and launch log errors | CS5, CS5.5, CS6, CC -
https://helpx.adobe.com/x-productkb/global/installation-launch-log-errors-creative.html -
My creative CC for teams gives an error code (-60) download corrupted when trying to install any app from the CC on my desktop. Any help?
Rasco1 it sounds like your managed network needs to be configured to allow you to download successfully. You can find more details in Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html.
-
PIXMA330 and new computer with Windows 8.1. Error Code 2,148,0 when trying to scan
I have a PIXMA330 and bought new computer with Windows 8.1. I get error code 2,148,0 when trying to scan. I tried to download updated driver but still have the problem. Is this common? Thank you.
You may have a BIOS problem, but there are no drivers for the BIOS. The BIOS is the system firmware. You will have to go to the support website of the computer/motherboard manufacturer to look for a BIOS update as Windows has nothing to do with
the BIOS - that is the sole responsibility of the computer/motherboard manufacturer.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ” -
I keep getting result code -43 not found when trying to load certain instruments. Any idea why
I keep getting error code -43 not found when trying to load certain instruments. Any ideas?
Errors 3000-3999 (3004, 3013, 3014, 3018, 3164, 3194, and so on): Error codes in the 3000 range generally mean that iTunes cannot contact the update server (gs.apple.com) on ports 80 or 443.
Update to the latest version of iTunes.
Verify the computer's date and time are accurate.
Check that your security or firewall software is not interfering with ports 80 or 443, or with the server gs.apple.com.
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
An entry in your hosts file may be redirecting requests to gs.apple.com (see "Unable to contact the iOS software update server gs.apple.com" above).
Internet proxy settings can cause this issue. If you are using a proxy, try without using one.
Test restoring while connected to a known-good network. -
Apple Cinema Display 23" - Blank Screen, "short-long-short" LED code
Hello everyone.
This sounds like something of an epidemic... My Apple Cinema 23" HD Display (bought Dec. 2007) hasn't been turning on after a power outage hit our area last week.
The Computer and Display were OFF when the outage occurred. Everything was plugged into a surge suppressor. Everything ELSE plugged in to the suppressor is fine (including my Mac CPU)... but not the monitor.
It’s not dead-dead…. It’s a blank screen but there IS a morse-code flash on the LED (short-long-short). According to Apple Support’s LED Translation, it SHOULD be something to do with the power adaptor. The adaptor IS correct… a 90 watt… but just in case I bought ANOTHER 90w adaptor brick. I plugged the monitor to the new brick. THE RESULT WAS THE SAME.
I’ve tried power cycling, I’ve tried plugging it into different outlets, I’ve tried connecting to other computers. The same LED result remains.
And, yes, of course, I’ve got no Apple Support, and from what I read in similar posts, outside-the-warranty repairs could hit around $400. I REFUSE!
For now I have a Samsung monitor from Costco. It’s not bad, but it’s not the Apple monitor with its awesome color-fidelity.
I've read some other posts with the same problem (LED blink code and all) elsewhere but haven't got a solid answer.
I wonder… has anyone else incurring this same problem (with the same LED flashing deal) tried to use a 150-WATT adaptor brick? I would try this myself, but I’m currently financially unable (and personally unwilling) to throw more cash at this problem unless I know it’ll fix it.Hi all!
As mentioned on the title of this topic *I HAD THE EXACT SAME PROBLEM* with my 23" Cinema Display...
Before the failure, the monitor *WAS IN PERFECT CONDITION* (trust me when I comment this, my whole life is in front of a monitor)
*THE PROBLEM SHOWED UP THE DAY I MOVED THE MONITOR TO AN OTHER OFFICE* (???). Please note that *I TOOK EXTRA CARE WHEN I MOVED THE MONITOR*, besides, when something costs around 1K you owe to.
*I TRIED AN 150W ADAPTER ON IT AND WORKED FINE!!!* Just like before.
But since *IT WAS UNDER GUARANTY* I sent it to the local distributor who eventually *REPLACED IT WITH A "NEW" ONE*, which after remarks from my side it turned out it wasn't "new" but re-manufactured by Apple (off course, he guarantied me the parts in it, where brand new and had 0 hours of usage).
In my question to the technical representative of Apple *"WHAT WAS WRONG WITH MY MONITOR"*, he answered me that *THE INVERTER WAS FAULT*.
After that I questioned him *"WHY MY MONITOR MANAGED TO WORK WITH THE 150W ADAPTER?"*, he answered me that *THE EXTRA CHARGE OF THE 150W ADAPTER WAS ABLE TO "EXCITE" SUCCESSFULLY THE FAULTY INVERTER IN ORDER TO WORK* and that *IT WAS A MATTER OF MONTHS FOR THE MONITOR TO FAIL AGAIN*.
That's my story... I hope it may help some of you... Personally I can't have an opinion on the matter, since I'm not a technician. The only thing on which I can comment is that *A 1K MONITOR SHOULD BE WAY MORE DURABLE AND TOLERANT WHEN YOU TRANSFER IT AROUND (if that cause the problem of course)* -
Error code 80070022 and 80070057 when trying to backup music from iPod Classic
Hello. I'm attempting to backup all of the music from my 80GB iPod Classic to my Windows Vista computer. My old computer (the one originally with the backed up music) died on me, so iTunes wont backup music from my iPod to the computer. So I am forced to either use a 3rd party transfer software or transfer the music from the iPod's file system. Attempting a backup either of these ways results in errors that prevent the computer from transfering 95% of the music. The 3rd party software offers no information about the error, but copy/pasting from the iPod file system to the PC returns the following errors:
error code 0x80070022 (first error message)
error code 0x80070057 (subsequent error messages for 95% of music files attempting to be copied)
If I try transferring through the iPod's file system on my Macbook Pro, I get error code -36.
I've tried restarting both the PC and iPod, and I've also tried the transfer in safe mode. Both attempts have not solved this problem. Most of the 12,000 songs on the iPod were ripped long ago from CDs I own. I've also painstakingly rated every one of these songs. I'm very worried that one day my iPod will crap out on me and the ratings will be gone forever and I'll have to spend tons of time reripping those CDs again. I've also googled this problem and have found little help.
Other details - this iPod was originlly set up on a WinXP PC. Addionally, I should note that I have no problems connecting to itunes or playing any of the music files. These errors are only preventing me from copying music files to my PC or Mac.
Thank you in advance!I Googled that
http://www.google.com/search?q=Currentencoder+settings+for+bit+rate+and+sample+rate+are+not+valid+for+thisfile&ie=utf-8&oe=utf-8&aq=t&rls=org.mozilla:en-US:official&client=firefox-a -
I have a classic, several years old.
It will not recharge; the Apple logo flashes every few seconds then disappears.
I have tried the 'reboot' advice i.e. move the Hold switch on and off, hold the Menu and Center buttons, no success.
I have tried this many times and kept the ipod connected for several hours. And I have tried two different cords, one connected to the desktop computer, one connected to electrical outlet.Hi enbridge4,
If your iPod Classic won't charge or turn on, you may find the following articles helpful:
Apple Support: iPod won't turn on
http://support.apple.com/kb/ts1383
Apple Support: iPod's battery doesn't charge
http://support.apple.com/kb/ta44551
Regards,
- Brenden -
I have been trying for 2 days now to get this resolved.
Computer hashard wired internet connection, running Windows 7 Home Premium. No other issues with downloading or uploading from any other sites or programs. No other network issues reported on other computers.
It started when I went to install Lightroom through my Creative Cloud. It prompted me to update my Creative Cloud Desktop App, which I went to do and then promptly got Error Code 201. I restarted my Creative Cloud and then skipped the update, hoping it was just an issue with that specific download. I clicked to install Lightroom and the same thing happened, Error code 201.
I restarted my machine, and tried again. Same issue.
I contacted Support. They had me go in and change a bunch of folder names to and add "old" to the end of them and then had me try using the Adobe Cleaner tool, which did not work. He had me go in and change some internet settings, still nothing. Same issues as before, only now with all the renaming of things I cannot even open programs I had previously been able to open like Photoshop.
He instructed me to reinstall the CC Desktop App because the Cleaner tool was not recognizing that it existed anymore (probably something to do with renaming files.. just saying) and now I get the 201 Error when I try to reinstall the CC Desktop App.
I ran out of time and had to stop after being on with them for over an hour.
Today I contact back and was instructed to create a new user account on my computer and try downloading and installing the application in the new user. Same errors. 213 at first, restarted my computer and then got Error Code 201 again.
I am getting really frustrated and really behind on my work. Any information someone could give me would be greatly appreciated. Currently waiting for a chat person to be available again.
Thank you for your time and assistance.Meowia for Error 201 please see Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html. Error 213 indicates there was problem locating the update or an incorrect URL. The troubleshooting steps are still the same as both errors are related to failure of the current network connection.
-
Error codes 1604 and 1602 when trying to update my iphone 3g to 3.0
ive tried and tried and tried, i have read the error resolutions for my error codes, ive tried a different computer, ive tried installing my usb drivers, everything!
all i seem to get when updating is, it says preparing iphone for update then the screen goes blank, baklight still on but the screen is black and then nothing for a min or 2 then i get the error code (one of the 2) can anyone help me and has anyone experienced the same thing?Nothing worked until i finally went to 8.1.10 FIRST. I had this same problem last week, updating a customer’s 3G to 3.0 from 2.2.1, on a MAC (using iTunes 8.2.1)! I tried on 2 different macs, 2 different sync cables, a bootcamp Vista SP1 on my MBpro and then XP pro SP3. All registered a 1602, 14 or 16 error everytime, about halfway through the update on the iPhone. I also tried removing the old 3.0 update and prefs file from the user data > app > apple directories with no luck. Also tried reinstalling itunes on the Mac.
What finally worked was:
- uninstall itunes (if you have anything above 8.1.10).
- move your itunes library file (for windows, it’s located under the iTunes directory, usually called iTunes Library.itl). You want iTunes to create a blank file since your 8.2.1 upgraded itl file won’t work with 8.1.10.
- put your ipod into DFU mode
- restore your iPhone to 2.2.1 using iTunes 8.1.10 (go here to download older versions of iTunes)
- use the same site above to download 8.2.0 (not 8.2.1).
- install 8.2.0 and connect your iPhone. It will notify you about the update. Download & install the 3.0 update (if you uninstalled, the 3.0 update should be deleted).
- upgrade back to 8.2.1
- move your library (itl) file back. To be safe, I would hold the shift key down to select your 8.2.1 file (even if it’s named the same as the one you created from iTunes 8.1.10).
1 hour later, I have everything updated. All I can say is that there’s a bug in 8.2.1 that wasn’t there in 8.2.0. I updated my iPod Touch first gen no problem with 8.1. Hope it works for others. -
"Error 300: Failure to boot" When trying to boot up imac
This is the error I get when I try to boot up my imac, it will not boot up, just leaves me with this Error 300: Failure to boot. I don't know what to do as I'm not all that mac - knowlegeable. Please help me if you can.
Message from daughter in Italy:
Here's what happened. When I typed in the first line, the output was a TON of lines somewhat like this:
-rw-rw-r-- 1 0 80 12292 (a date, a time) (Firefox, Users, etc.)
drw------- 7 0 99 238 (a date, a time) (Volumes, afs, bin,etc.)
d-wx-wx-wt 2 0 80 68 (a date, a time) (var -> /private/var, etc)
drwxr-xr-x 1 0 80 649 (a date, a time) (Desktop Folder, private)
There were lots of lines that started with drwxr. Also, where I typed parentheses above, there weren't any parentheses (that's just to show where the date and time would be). And on the very last item, those things listed in parentheses (which were not on the code) include some samplings of what was listed there (but not necessarily corresponding to the previous code in the line that I typed -- I just wrote down some of the words I saw throughout). There was only one word at the end of each line (or sometimes something like the very two last lines, which were var -> /private/var and one other somewhat like it with the var.delete code.
When I typed in the second line of code suggested, there was nothing, just a new prompt (that same weird prompt with the pound sign).
When I typed in the third line of code suggested, the output was the following:
ls: /private/etc/: No such file or directory
Also, when I typed in the very first line of code, there was no weird prompt thing...just a blank line with the cursor blinking. The prompt thing always appears after you type in something and hit return.
Hope that all makes sense (at least to the Apple geniuses out there). Thank you!! -
Using imovie, I am trying to export a movie however it keeps flashing error code -50 every time I try. Doesn anyone know what this error means and how I can correct the problem?
Hi, one thing I discovered was that this error message was being given whenever I tried to export the project into iTunes as a Large file. When I tried to do the same thing in to iTunes as a Mobile or a Medium file it exported fine.
I tried a workaround which was to recompile the movie again by capturing the video as one file and the audio as another file and then to import them both in to iMovie and combine them as a new project.
Once this was done, I successfully exported the new project in to iTunes (using the HD format option!).
I used Quick Time to create both the screen capture and the audio for the above workaround.
The result was that the file was still a very good quality movie. Perhaps not as good as if iMovie had worked properly, nevertheless, it removed my frustration.
Furthermore, given that the Medium format movie exported ok, even that could be used to share on other social networking sites such as YouTube.
Hope that helps. -
Mac pro won't boot, keeps trying to reboot
Two days ago, my Mac Pro (early 08) just starting flickering on the display and it wouldn't stop. The entire system froze except for flickering display. I had to shut down by holding in the power button. Now when I try to boot the machine, I get the apple screen, the little clock timer and then suddenly it freezes, shuts the machine down and tries to boot itself again. It will do this again and again until I hold the power button to shut it off.
I have an external boot drive. I connected it. It does the same behavior with the boot drive. I could be wrong but this sounds bad. Any ideas?
Running most recent Mountain Lion OSYes. Any 2008 3,1 you should make 10.6.8 your primary OS and only use ML or Lion for those "necessary" times but not for production.
Not knowing your hardare, whether you did a clean install of ML or not... 3rd party hardware and even external devices... -
Getting error code when synching with iTunes. Never had a problem before updating iOS and my Mac.
iTunes: Specific update-and-restore error messages and advanced troubleshooting - http://support.apple.com/kb/TS3694 - relating to iPad, iPhone, iPod touch, iTunes
Maybe you are looking for
-
The problem began after a recent Firefox update. Occasionally, when I try to open a new Firefox window, all I get is a grey screen with a tiny section of my homepage visible in the top left corner of the screen. NOTE: Firefox stores all of these abor
-
Hard Drive is designated as "F" drive and IPod doesn't recognize it
My hard drive is designated as the "F" drive, and I think the IPod is looking for it as the "C" drive. Can anyone tell me how to fix this?
-
Need help troubleshooting issues with Adobe Reader X
Hello, Recently our company upgraded multilpe computers to Reader X. Initially we installed version 10.1.0. Ever since our users on X have been experiencing problems. We are seeing three different issues. 1) A user will fill out the PDF and click
-
I bought a clamshell 466 graphite for my 10 year old son for Christmas and am having a couple of problems. I have an Airport Extreme for my Powerbook G4 and e-Mac and have a network set up. I followed the set-up wizard for the Airport Extreme for thi
-
Software update & new version of os e 63
how i can update s/w 4 E63 ans i want update os what i do .