Longer power cord for airport extreme

I am needing a longer power cord cord for my new airport extreme base station Model ME918LL/A.  It's the cube one with the internal power supply.  It only comes with a six foot cord and I need at least 12 feet to place it in the optimal place in our office.  In suggestions where I can find a longer cord.  Amazon and tiger direct sale cords that look similar, but I want to be careful and fry it the device.  Has anyone else had a similar problem and where did you find a longer cord?

You  may have to reconsider the diameter of holes through which
the wire has to pass, or discover an alternative power source at
a nearer distance to the AirPort Extreme (with backup power &
perhaps a backup battery type of power unit w/ power filter.)
Part of the problem with distance and electrical signal over wire
is that a larger capacity wire is needed due to loss over distance.
The greater the distance, and the larger the gauge is needed.
A lower-than-specification power at the unit likely would result
from too-long a power lead.
My AirPort units (Extreme and Express, in use) are protected by
a battery-backup APC or other automatic device that switches to
its own battery and takes the unit offline when power it too high
or when it is too low. And not one of the cheaper backup units.
So the issue isn't just a long cord, but one of significant better
quality than just a long cord of the same external diameter case
or layer of insulation over whatever gauge lies beneath.
That's a reason why the wire isn't longer; it'd also have to be larger
in wire gauge capacity and heavier. Then other costs would add up.
You may be able to ask a professional appliance company who could
look over the AirPort Extreme power cord and match the small end
where the unit plugs in, with one of a higher gauge wire (larger wire
so that's a smaller number wire for larger size/gauge; for the distance.
However you do it, have fun...
Good luck & happy computing!

Similar Messages

  • Missing power cord for Airport Extreme model 1034 (2003)

    I found my old Airport extreme, the white dome type model 1034 (2003). I replaced it with a time machine a few years ago. Now I would like to use it to extend my network into my studio but I can't find the power cord. Can I use a universal adapter input 5.1volts 2.4A? If not, where can I get a new power cord?

    Seems like Apple Support would be a good place to start. If Apple does not have the item, I doubt that anyone else will either.
    http://www.apple.com/support/contact/

  • Need power cable for airport extreme

    need power cable for airport extreme

    http://www.mac-pro.com/Airport-Extreme-Base-Station-Power-Adapter
    Just one of many if you enter AirPort Extreme Power Adapter in a Google search.

  • Longer Power Cord for new G5

    Just received the new 20" G5 and was a little dismayed at how short the power cord is. I want to situate my mac in the center of a room and I can, of course, use a simple extension cord but I was wondering if anyone made a longer power cord that would be compatible with the "mickey mouse" input on the back of the mac. Does anyone know if such an item exists and if so, how to get one?

    Dale,
    I believe the power cord is of standard length. It will be difficult to find a longer one. Perhaps you could build your own power strip for whatever furniture you want to place the iMac on. The power strip can have a long enough cord, and you would have something to plug other stuff in to.
    Steve
    PS - I find nothing 'Mickey Mouse" about the connector. It's too round

  • Power Supply for Airport Extreme

    Hi
    Does anyone know where I can get a new power supply for my airport extreme in the UK? Mine has died, and I don't really want to buy a whole new base station just because of the external supply. (I know the actual unit is working through plugging in a power supply from my other base station)
    I tried Apple, who weren't really any help.
    Thanks in advance!
    Tom.

    Tom welcome to the discussions.
    I would probably call the Apple number.
    1-800-MY APPLE
    I am sure that they can point you in the right direction.
    I am a little shocked that one of the Apple Retail stores can't offer you a Power Supply.
    If all else fails, it sounds like you have tried an alternitve, if it works use it, until you can get a replacment.
    Don

  • Changing power output for Airport Extreme Card

    How do you change the power output for the Airport Extreme Card? Is there a program that I can download to change airport's settings or the Airport Extreme Card's settings?
    i.e. If the default power output for the Airport Extreme Card is 18mW, I would like to increase it to 25mW.

    There is no way for a user to control the power output of the AirPort Extreme card.
    Furthermore if the card was manufactured to output 18mW there is no magical way to increase it's physical ability so it can output more power.

  • Power Injector for Airport Extreme (Generation 5)

    Hello.
    Is there any support for using Power Injector (PoE) instead of the supplied power apdater to run Airport Extreme.
    Cheers
    Mr Apro

    Sorry, but Power over Ethernet is not supported on the AirPort Extreme.

  • Where can you get the power cord for a 2012 airport express?

    Where can you get a power cord for a 2012 airport express or the equivalent? I couldn't find one in the online store.

    I'm sure the OP found his solution, but I wanted to share mine in case it helps some future seeker.
    There are a lot of brand new cords on eBay for less than $10 including shipping, which is way cheaper than the $39 stereo connector kit or an AC adapter from a retailer.  I just bought a used-like-new one for $5.50.
    The cord is made by Volex, part number APC7Q.  The Apple part number is M9573LL/A.  If the seller got it from the stereo adapter kit, they'll probably list it under MD836LL/A, which is the kit's part number.  I got the best search results on eBay using just the Volex part number.
    Best of luck!

  • HT201897 Does a Mac Mini purchased in the USA require a power converter for operation in Europe or should I only purchase a different power cord for it?

    Does a Mac Mini purchased in the USA require a power converter to operate outside of the USA or can I simply purchase a different power cord for it?

    Depending on which European country (should their mains access plug/port shape vary) the
    cord set with correct ends on it has to match. You can buy a cord that plugs into the Mini
    where the factory cord goes, and the other end has one for the wall source shape. The wire
    for the application should be able to support 110~240VAC.
    With the cord or an accurate image in hand, you could either get a new cable to match both
    realities (mini + wall supply mains local) or an adapter (US/Standard to EU/Local) for just
    the head or input part of the original Apple cable. One plugs into the other, then into wall.
    If you have a new Mini with a small modular plug/port on the computer end of the power wire,
    it would have only two holes and no ground; the other end would have two prongs of equal
    shape and size. Not a polarized plug and not a grounded three-prong. To get a replacement
    power wire for the MINI to go from power source to the Mini is recommended, if you are going
    to be staying in one location for awhile. A Travel Kit that offers no electrical conversion but only
    the physical shape adapter kit, should a available in travel stores, airports; big box discount
    stores, computer and electronic stores. This page shows the cord end of the appliance shapes.
    The other end would be the mains shape for whichever country you are going to....
    http://www.signalandpower.com/European-Power-Cords/
    So to match the country or regional power mains type is a primary concern for obtaining the
    correct replacement cord to supply the Mini with local mains power. The end which plugs into
    the Mini is of a certain type (numbers for EU and elsewhere are published, see link + images)
    & the end that gets plugged into the mains or utility side, needs to match the local specification.
    The link to Apple, to contact for Support and Service information in prior post, should be able
    to help find a source for the local replacement type cord they'd sell local people with a Mini.
    Apple local sources offer replacements for this purpose; and for travelers, a second cord for
    a direct use (not adapter plugs) is a better bet. For those who only need a cord in two places.
    If you are traveling to Denmark, UK, Swiss or other EU countries require different adapters.
    Even places where the power itself may be somewhat similar. However your MINI has an
    automatic power supply that will conform to that energy standard, you only need to supply a
    correct non-transforming adapter. Simply a connection to adapt one shape to another.
    The general purpose travel kit that is not specialized to Apple power adapters, would have a
    plastic plug/adapter with the local pins on one side, and the US/standard two slots on the other.
    So, no circuitry nor any other change of electrical power inside this device would be required.
    http://www.signalandpower.com/2-Prong-Plug-Adapters/
    http://www.signalandpower.com/Convert-to-Europe-CEE-716-plug/
    http://www.signalandpower.com/Swiss-AC-Power-Cords/
    In other words, I believe my other post already covered this. On the ground on either end of the
    path, adapters are common and the Mini does not use proprietary electrical components IF you
    have one of the more recent shape aluminum models with the power supply built in. The older
    Mini has the power brick and two wires. A US/Standard plug adapter to EU/Local would work in
    either case, since all you'd do is plug the adapter plug into the local mains and the US plug into
    that one... I see these kinds of discards for as little as 25¢ in thrift stores in Alaska. Or you can
    buy a new one. Or you could get a complete cord with correct ends on it, for Mini + local mains.
    Hopefully this helps somewhat. The only info missing is which EU country or region is involved.
    Their shapes of plug are different, so the adapter end for local supply has to match their standard.
    Swiss, Denmark, UK, and others offer different shapes and so on.
    The Apple store in the location you are traveling should be able to supply you with a replacement
    cable for a modern MINI, that has the correct local mains end, and the correct Apple mini end on
    the opposite. Since the unit is automatically switching, the magic is done.
    Since I supplied a means to locate any number of Apple stores, authorized service providers &
    other Apple related vendors in my earlier reply: https://locate.apple.com/country you could contact
    any of them along your route in the City in whichever EU country, to find a local MINI power cable.
    In any event, I'm done...
    Good luck and happy trails...

  • HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
    Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
    As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
    Is there a way to resolve this issue?

  • I need a power cord for a sony CFD-G700CP

    I need a power cord for a Sony boombox CFD-G700CP.  Where can I purchase one.

    The power cord of the CFD-G700CP Boombox is no longer available at our Parts Center. You may check for it from any of our Authorized distributors below: 
    Andrews Electronics Inc.
    1-800-289-0300
    www.andrewselectronics.com
    Encompass Parts Distribution
    1-800-638-3328
    www.encompassparts.com
    Fox International
    1-800-321-6993
    www.fox-international.com
    Union Electronics
    1-800-648-6657
    www.ued.net
    If my post answers your question, please mark it as "Accept as Solution"
    http://bit.ly/Win-4K

  • Seeking a longer power cord???  (G4-flatscreen IMAC)

    Are longer power cords available rather than the standard 6-footers? If not, does anyone have a solution that would get me to at least 8 feet? Thanks.

    Sure voltage drops off over long distance; but as all Macs have auto-switched power supplies capable of running with anything between 100 - 240 volts AC at 50-60Hz there really isn't an issue. I remember watching a colleague plug his Compaq laptop (rate for a 230VAC european supply) in to a 115 volt socket. It actually stuttered on DVD playback! 
    This won't be an issue. You can either use a domestic extension lead as JPT says or buy a longer 'cloverleaf' mains cable.
    regards
    mrtotes

  • I need a new power cord for my Mac book Pro its the T type mag connector. I don't need a Tech just a new cord. How do I buy one. The closest Aplle store is 75 miles away and I do not drive.

    I need a new power cord for my Mac book Pro its the T type mag connector. I don't need a Tech just a new cord. How do I buy one. The closest Aplle store is 75 miles away and I do not drive.

    Are you in the US? Order one from here:  http://store.apple.com/us/browse/home/shop_mac/mac_accessories/power?mco=MTM3NjU xNDg
    Or check out Best Buy.

  • Power Cord for Italy/Europe?

    Hi folks. I have the 85w AC adapter with the power cord for the US.
    I realize I can get an adapter for the plugs in Italy, but I was wondering if I could order the AC cord that goes from the wall to the adapter.
    Basically I'm looking for the Euro version of 922-5463 AC Adapter Power Cord.
    This isn't a huge priority, since I have the world travel kit and a set of adapters, but I figure since I'll be travelling alot (if I get the job) it might be a good idea to have the native cord rather than constantly use adapters.
    I'd also like to keep the machine grounded as often as possible. The travel set doesn't appear to support grounding.

    Nevermind, I found what I needed on eBay.
    I went to eBay's Italian portal and searched for AC cord un the Apple section.

  • Where can I get a replacement power cord for my 13" Mac book, Where can I get a replacement power cord for my 13" Mac book

    Where can I get a replacement apple charger/power cord for my 13" Mac book?

    here are some examples: https://www.google.com/#q=macbook+magsafe+adapter&hl=en&prmd=imvns&source=univ&t bm=shop&tbo=u&sa=X&ei=i6nhTrvTO6q22gWIpuTcBA&sqi=2&ved=0CHkQrQQ&bav=on.2,or.r_gc .r_pw.r_cp.,cf.osb&fp=e0f7ed75ce37ea0c&biw=1280&bih=679

Maybe you are looking for

  • Can not see ODS infosource in the system

    Hello, I am unable to see Infosource of my ODS under the infosources tree. This is only happening in DEV and PROD. In QA system i could see it and also create additional infopackages. The bottom line is I want to be able to create extra Infopackages

  • How to set the initial path of a Select File dialog.

    I'm using the Flex3 File.browseForOpen() method.  I'm opening a xml file; but I want to seed a path to the open dialog so used don't have to do much file navigation.   Is there a way to specify a path that the file browser starts in? Thanks. -Hays

  • Customer Outstanding Report

    Hi All, We are about to provide a Customer Outstanding Report to the client. The requirement is customer ageing analysis along with all the deductions made for the invoices. The deductions are like IT-TDS, WCT-TDS, Retention, Mobilisation Advance, et

  • How to set screen to face out

    I'm working on a project that ends with a white slide, which is being used as the fade out screen. But the client would like the second to the last slide (the last slide in the presentation) to fade out completely before transitioning to actual final

  • Sun cluster Node ID Order

    I installed Sun cluster 3.1 and it all seemed successful. However, the node ID and the private hostnames seemed twisted. "comdb1" has the node ID of 2 and "comdb2" has the node ID of 1. I installed the software from "comdb1", so it should have used t