Looking for Cisco 3850 power-stack OID

Hi all,
Does anyone know the OID for the Powerstack interfaces of the Cisco 3850?
It is not the normal ifentry like the data-stacking cables!
Thanks
Willem

Hi,
See this information below:
24-Port PoE Switch
48-Port PoE Switch
PoE on all ports (15.4W per port)
One PWR-C1-715WAC
One PWR-C1-1100WAC or two PWR-C1-715WAC
PoE+ on all ports (30W per port)
One PWR-C1-1100WAC or two PWR-C1-715WAC
Two PWR-C1-1100WAC or one PWR-C1-1100WAC and one PWR-C1-715WAC
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3850-series-switches/data_sheet_c78-720918.html
Hope this helps.

Similar Messages

  • Cisco 3850 Power Stack

    Hi
    We recently purchased four Cisco 3850 switches (WS-C3850-48P-S) which comes with 715WAC power supply. We have also purchased additional four 1100WAC power supplies.
    Our requirements are:
    Configure four switches in stack
    Use power stack feature
    All 192 ports in Stack should be POE enabled
    Questions:
    Can we use both 715WAC and 1100WAC power supplies in same switch
    Can we have all ports POE enabled with having both 715WAC and 1100WAC power supplie
    Thanks
    Muhammad Ibrahim

    Hi,
    See this information below:
    24-Port PoE Switch
    48-Port PoE Switch
    PoE on all ports (15.4W per port)
    One PWR-C1-715WAC
    One PWR-C1-1100WAC or two PWR-C1-715WAC
    PoE+ on all ports (30W per port)
    One PWR-C1-1100WAC or two PWR-C1-715WAC
    Two PWR-C1-1100WAC or one PWR-C1-1100WAC and one PWR-C1-715WAC
    http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3850-series-switches/data_sheet_c78-720918.html
    Hope this helps.

  • Looking for Cisco service providers outside of USA

    I am looking for Cisco service providers in Guyana.
    It can be a third party vendor for Cisco partner for Cisco infrastructure maintenance.
    Thanks,
    Sam

    Hello, xszhuMerak1. 
    I can help you find local Cisco support on your area. Would you be able to tell me for what Cisco infrastructure this support will be? Let me know if you have additional concerns or e-mail ([email protected]) me directly. Kind regards. 

  • Looking For: DDTS-100 Power Adapter

    Hi everyone,
    I'm looking for a power adapter/cord for a DDTS-100. Any of you have one available for me to take off you. I'm willing to pay for it. Please message me ASAP. Thanks.
    Message Edited by Cero2 on 05-16-2007 02:07 PM

    Thanks for the specs. Unfortunately, the real problem is 6V AC adapters are extremely hard to come by, as I can't find one anywhere.

  • Looking for Cisco administration software

    Hi.
    I am looking for a Cisco software that permit me to restrict and control connections changes for ip phones and pc's to my net 3750 switches or something seemed that I could do in my 3750 switches (I know that I can configue static mac's for each switch port but I have five hundred phones and It is a huge work that I don't want to do). Can anybody say me any idea? I have the problem that users in my office are always changing their phones from their switch ports and this produce an huge administrative effort to have a good net inventary.
    Thanks.

    The system status box shows the following information:
    Active meetings: Shows the number of meetings currently in progress.
    Errors: Shows the total number of system errors that are defined as either CRIT or ERROR. If the total number of system errors is 0, a green check is displayed. If the total number of system errors is more than 0, a red cross is displayed. System Troubleshooting the CTMS System."
    Warnings: Shows the total number of system errors defined as WARN. If the total number of system errors is 0, a green check is displayed. If the total number of system errors is more than 0, a red cross is displayed. Status: Shows the current state of all system processes. If all system processes are in the RUNNING state, a green check is displayed. If one or more processes are in the STOPPED state, a red check is displayed. System processes are described in "Chapter 6: Monitoring CTMS System Processes."

  • Looking for Cisco-Linksys WRT330N antenna.

    Im looking for the directional antenna from that router, also i would like to know what is the gain on those.
    Please reply with any information

    Antenna of the WRT330N is not detachable.

  • Looking for Cisco 6500 E series 1/10 G SFP Module

    I am looking for 24 ports 1/10G SFP module for my 6509E chassis and WS-SUP720-3B sup module.
    I have found the following from my research
    WS-X6704-10GE - 4 port 10G module which supports only 10G not 1G
    WS-X6708-10G-3C - 8 Port 10G module which supports only 10G not 1G
    WS-X6724-SFP - 24 Port 1G SFP module which supports only 1G not 10G
    Thanks for your help

    Hi datamodule, i see that you are looking for a 24 ports 1/10G SFP module for the Catalyst 6509E. From what i am looking at it's either 1G or 10G. Please check this link for further assistance: http://cs.co/9000YTBE. Feel free to message me for further assistance.
    Thanks,
    Angela ([email protected])

  • Looking for Apple TV power supply - any ideas?

    Hi folks,
    My out of warranty Apple TV has an obvious power supply problem (it's totally dead, no power up whatsoever).
    There are a few websites that have tutorials on replacing the power supply (or hard drive, etc...).
    The problem is I can't find a place to purchase a replacement power supply.
    It's a Delta Electronics ADP-36BF, Apple part # 614-0395 (http://s1.guide-images.ifixit.com/igi/HGslJDZeqPnKlFVD.huge)
    Any ideas on where to find one?
    If I can't get it myself to replace it, I'll probably just wait for the Boxee Box to replace it.
    Thanks.

    I'm in the exact same boat -- I've looked everywhere and can't find anything. I've even called Delta Electronics about the part and they said they can only sell them to Apple. If you find anything out please let me know! Thanks.

  • Looking for availability of SP stack #18 for Canada... any ideas when avail

    we've been watching the marketplace and it looks like SP #18 is not available until July 8th? could that be possible when canadian payroll standard to patch should be July 1st?
    could someone please advise on the process asap.  We have just gone live with HCM (peoplesoft time and labour and Payroll) migration to SAP HCM.  and will now work with very tight timelines as we watch the first couple of pays in a new system, as well as working on deffered items, while trying to patch and test the system...
    any info. is muchly appreciated
    mg

    Hello Maria,
    We usually update our system twice per year, in late May or early June (before the Mid-Year Tax Update) and in Nobember or early December (before the Year-End Tax Update). 
    First, our Basis Team makes a copy of PRD to refresh our QAT and SND (Sandbox), then we apply the second to latest patch.
    Of course, that makes for a lot of Notes to go through, but we try to focus only on the Notes relevant to our System/Country.
    This year, since we did not do an update in mid-year, we'll have that much more to go though in November.
    P.S.  We also apply selected Notes when required, throughout the year.

  • Looking for feedback using Power Sync cart and apple configurator

    I am looking at mass deploying iPads using the Bretford PowerSync Cart and Apple Configurator.  Need information on how long it takes to fully power and sync units?

    You might try a Google search. Here's one I found.
    http://www.markrepp.com/2012/03/apple-configurator.html
     Cheers, Tom

  • Cisco 3850 (FAN)

    Hi Every Body,
    the customer is looking for switch 3850 POE with 3 fans & dual power redundancy, my question is;
    how many fan existing in the switch by default. in otherhand how much i have to buy fan for each switch. 
    :) thanks,

    Hi,
    By default the switch comes with 3 fans and that is maximum. You can't add additional fans.
    http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3850-series-switches/data_sheet_c78-720918.html
    HTH

  • Looking for a (broken?) G5 or a G5-Case

    Hi,
    as the subject already says, am I looking for a broken Power Mac G5 tower.
    I used to work with one 2 years ago (during my military service) and learned to love its high-quality appearance!

    I did (and are still doing) this the last week.
    There are a lot of Cases sold in the USA - for less than 70$...!
    Unfortunately the shipping is about 200$
    But there are not many sold in Germany - so I hoped to find one this way.
    2 weeks ago I asked at an Apple-store support-counter. But they told me that they are not allowed to sell these privately.

  • Power Redundancy problem for cisco 3750 stack switches

    Hi Team,
    I have installed and configured cisco 3750X series switches in stackwise. Those are having dual power supply.
    Power redundancy test performed:
    1. Removed one of the power supply and inserted it back.
    2. once the first power supply is ready, removed another power supply and switch got rebooted.
    please find the below stack-power output:
    JP2-RDC-DIS-02#sh stack-power detail
    Power Stack           Stack   Stack    Total   Rsvd    Alloc   Unused  Num  Num
    Name                  Mode    Topolgy  Pwr(W)  Pwr(W)  Pwr(W)  Pwr(W)  SW   PS
    Powerstack-2          SP-PS   Stndaln  700     477     223     0       1    2
    Powerstack-1          SP-PS   Stndaln  700     477     223     0       1    2
    Power stack name: Powerstack-2
        Stack mode: Power sharing
        Stack topology: Standalone
        Switch 2:
            Power budget: 223
            Power allocated: 223
            Low port priority value: 22
            High port priority value: 13
            Switch priority value: 4
            Port 1 status: Not connected
            Port 2 status: Not connected
            Neighbor on port 1: 0000.0000.0000
            Neighbor on port 2: 0000.0000.0000
    Power stack name: Powerstack-1
        Stack mode: Power sharing
        Stack topology: Standalone
        Switch 1:
            Power budget: 223
            Power allocated: 223
            Low port priority value: 22
            High port priority value: 13
            Switch priority value: 4
            Port 1 status: Not connected
            Port 2 status: Not connected
            Neighbor on port 1: 0000.0000.0000
            Neighbor on port 2: 0000.0000.0000
    Can anyone help what went wrong here?
    Thanks
    Manish

    Cosmetic bug
    CSCui21029    3750X Stack no standalone stays in running configureation as standalone
    Symptom:
    When you are configuring a 3750x stack and initially putting it into a stack ring topology by configuring the following.
    Switch(config)#stack-power switch 1
    Switch(config-switch-stackpower)#sta
    Switch(config-switch-stackpower)#no stan
    Switch(config-switch-stackpower)#no standalone
    You will see that in the running configuration it shows up as standalone mode
    stack-power switch 1
    switch mode: standalone
    stack-power switch 2
    switch mode: standalone
    Conditions:
    3750X stacks with any license level
    Workaround:
    none

  • Looking for an OID string for the IE-3000 switch

    I'm looking for the OID string on a IE-3000 switch to give me the results for the optical Tx and Rx power as shown in the "show interface transceiver" command (this is the output i ran directely from the IE-3000 switch, BTW):
                                     Optical   Optical
               Temperature  Voltage  Tx Power  Rx Power
    Port       (Celsius)    (Volts)  (dBm)     (dBm)
    Gi1/1        30.1       3.29      -6.1      -7.3
    The OID I am using on our 6509 switch for Rx power is .1.3.6.1.4.1.9.9.91.1.1.1.1.4.xxx (where xxx is the ifindex number), but I can't seem to find anything similar for it on the IE3000.  The closest I have found are the following, but those appear to be just descriptor tags:
    .1.3.6.1.2.1.47.1.1.1.1.2.1029 (tx)
    .1.3.6.1.2.1.47.1.1.1.1.2.1030 (rx)
    Thanks for any help!
    Kim

    Kim,
    Have you tried the Cisco on-line tool called the SNMP Object Navigator?
    You can use it to translate OID into object name or object name into OID to receive object details.
    http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en
    If you cannot find the reply you need in this forum, try posting to the LAN or WAN Routing and Switching forums.  This forum is mainly for optical issues (SONET, SDH, equipment)
    Hope this helps,
    -SteveN

  • Look for SG200-26 OID

    Hello  and sorry for my English.
    I use SNMP for my Cisco, more than 30 Cisco switchs in my network.
    we had buy a new model : SG200-26 and i don t find OID for this switch like others, i think that most of MIB are not supported :-(
    I look for :
    ciscoMemoryPoolFree
    CpmCPUTotal5minRev
    ciscoMemoryPoolUsed
    thanks for help

    I suppose you mean I should add the address of the switch instead the one you added.
    I already added the switch address to list of trusted sites, but this not helps.
    Please keep in mind, that I have this behaviour on several different browsers on different machines:
    Desktop client
    - IE11 on Windows 8.1x64
    - Firefox 34 on Windows 8.1x64
    - Iron 35 on Windows 8.1x64
    Notebook1
    - IE11 on Windows 8.1x64
    Notebook2
    - IE11 on Windows 10
    Cell phone:
    - Chrome 28 on Android (KitKat)
    - Firefox 34 on Android
    iPad:
    - Mobile Safari 8 on iOS 8.1
    - Chrome 39 on iOS 8.1
    Additional Info:
    When opening the online device emulator under https://www.cisco.com/assets/sol/sb/Nikola_GUI/SG_200-50P_v1_1/config/home_sx200.htm
    I shortly see the menu text on the left side until it disappears. Then I see a mixed picture (text on main screen, only boxes on menu frame)

Maybe you are looking for