Looking for Cisco 6500 E series 1/10 G SFP Module

I am looking for 24 ports 1/10G SFP module for my 6509E chassis and WS-SUP720-3B sup module.
I have found the following from my research
WS-X6704-10GE - 4 port 10G module which supports only 10G not 1G
WS-X6708-10G-3C - 8 Port 10G module which supports only 10G not 1G
WS-X6724-SFP - 24 Port 1G SFP module which supports only 1G not 10G
Thanks for your help

Hi datamodule, i see that you are looking for a 24 ports 1/10G SFP module for the Catalyst 6509E. From what i am looking at it's either 1G or 10G. Please check this link for further assistance: http://cs.co/9000YTBE. Feel free to message me for further assistance.
Thanks,
Angela ([email protected])

Similar Messages

  • How we archieve configuration for Cisco ASA 5500 series appliances

    Hi,
    We need to archieve configuration for Cisco ASA 5500 series appliances.
    We have Cisco works LMS 3.0.1.
    Device package installed is 4.2
    Any help would be appricated.
    Thanks in advance.
    Samir

    Hi ,
    Thanks for your answer.
    Right now we are using TACAS to login in to the ASA. That means we need single username and password to login via
    Cisoworks. Am I correct ?
    Waiting for your reply.
    thanks,
    Samir

  • Looking for Cisco service providers outside of USA

    I am looking for Cisco service providers in Guyana.
    It can be a third party vendor for Cisco partner for Cisco infrastructure maintenance.
    Thanks,
    Sam

    Hello, xszhuMerak1. 
    I can help you find local Cisco support on your area. Would you be able to tell me for what Cisco infrastructure this support will be? Let me know if you have additional concerns or e-mail ([email protected]) me directly. Kind regards. 

  • GUI Tool for Cisco 6500 Chassis

    Hi
    We have a requirement to allow our Service Desk to amend vlans on switchports on a range of 6509 chassis.
    Is there a tool, (like SDM for routers) which would allow them to do this using a GUI? We need to keep it as simple as possible as the Service Desk users have no experience of configuringCisco kit.
    We have Cisco Prime, however, I can't see anything which shows a graphical representation of the actual switchports on a chassis?
    If there isn't a Cisco product which supports this, does anyone know of a third party app which would do the job?
    Thanks
    J

    Hi datamodule, i see that you are looking for a 24 ports 1/10G SFP module for the Catalyst 6509E. From what i am looking at it's either 1G or 10G. Please check this link for further assistance: http://cs.co/9000YTBE. Feel free to message me for further assistance.
    Thanks,
    Angela ([email protected])

  • Looking for a NICOLET BE490 Series Driver for WIN- NT

    Hi,
    is there anybody, who has written a driver for the NICOLET BE490 Series
    Transient Recorder Board.
    Geetings Ruediger

    Hello,
    I just visited the Nicolet website and found an information sheet on this device that mentions "import and export capability" with LabVIEW...perhaps Nicolet can provide you with some LabVIEW resources to use this board.
    On another note...I took a look at the specifications for this device, and it looks like it would be more than adequately matched in performance by our E Series measurement devices, which integrate seamlessly with LabVIEW through our free NI-DAQ software. I recommend you visit www.ni.com/daq for more information about our high-class DAQ products.
    Good luck with your application, and have a pleasant day.
    Sincerely,
    Darren Nattinger
    Applications Engineer
    National Instruments
    Darren Nattinger, CLA
    LabVIEW Artisan and Nugget Penman

  • Looking for Cisco administration software

    Hi.
    I am looking for a Cisco software that permit me to restrict and control connections changes for ip phones and pc's to my net 3750 switches or something seemed that I could do in my 3750 switches (I know that I can configue static mac's for each switch port but I have five hundred phones and It is a huge work that I don't want to do). Can anybody say me any idea? I have the problem that users in my office are always changing their phones from their switch ports and this produce an huge administrative effort to have a good net inventary.
    Thanks.

    The system status box shows the following information:
    Active meetings: Shows the number of meetings currently in progress.
    Errors: Shows the total number of system errors that are defined as either CRIT or ERROR. If the total number of system errors is 0, a green check is displayed. If the total number of system errors is more than 0, a red cross is displayed. System Troubleshooting the CTMS System."
    Warnings: Shows the total number of system errors defined as WARN. If the total number of system errors is 0, a green check is displayed. If the total number of system errors is more than 0, a red cross is displayed. Status: Shows the current state of all system processes. If all system processes are in the RUNNING state, a green check is displayed. If one or more processes are in the STOPPED state, a red check is displayed. System processes are described in "Chapter 6: Monitoring CTMS System Processes."

  • Looking for Cisco-Linksys WRT330N antenna.

    Im looking for the directional antenna from that router, also i would like to know what is the gain on those.
    Please reply with any information

    Antenna of the WRT330N is not detachable.

  • I Am looking for parameterisation documents and UAT test cases of all modules,

    Hello Team,
    Flexcube 12 version test cases, I do have them but looking for flexcube old version. If any body can share it will be  help full and there will be some meaning in become a member of this group. my id is
    [email protected]

    p.lagatta wrote:Jon, Thanks for the reply.  The Siderwinder Firewalls associate a Multicast MAC address with the vIP.  That's the reason for the static ARP entry in each router.  Since our Layer II switches located between the firewalls and routers do not register the MAC with a specific port, both firewalls receive the traffic.  Once the traffic reaches the firewalls, they pass information across a heartbeat interface and the selection process is based on odd / even ports.  Receive traffic is already working in this configuration.  Both our external routers are peered with two EBGP routers located in the same AS.  The GLBP implementation will allow us to load balance the traffic each firewall is sending to the GW address.
    Perhaps i'm misunderstaning.
    If there is one mac-address then GLBP will assign that mac-address to one of the routers and it will keep that router for forwarding the traffic with the same mac-address. So the traffic will always be forwarded by the same router. GLBP works by assigning different source mac-addresses to different routers within the same group but it sounds like the source mac-address is always the same from the firewalls.
    Jon

  • Will Cisco WS-C2960X-24TD-L supports 1G SFP module. If yes kindly provide the part number..

    Will Cisco WS-C2960X-24TD-L series supports 1G SFP module. Switch is actually showing SPF+ port and i need to connect 1G uplink from remote Dlink Switch....

    WS-C2960X-24TD-L
    GLC-BX-D
    GLC-BX-U
    GLC-LH-SMD
    GLC-SX-MMD
    GLC-EX-SMD1
    GLC-ZX-SMD
    GLC-T
    GLC-ZX-SM
    GLC-LH-SM
    GLC-SX-MM
    CWDM-SFP
    http://www.cisco.com/c/en/us/td/docs/interfaces_modules/transceiver_modules/compatibility/matrix/GE_Tx_Matrix.html

  • Looking for Cisco 3850 power-stack OID

    Hi all,
    Does anyone know the OID for the Powerstack interfaces of the Cisco 3850?
    It is not the normal ifentry like the data-stacking cables!
    Thanks
    Willem

    Hi,
    See this information below:
    24-Port PoE Switch
    48-Port PoE Switch
    PoE on all ports (15.4W per port)
    One PWR-C1-715WAC
    One PWR-C1-1100WAC or two PWR-C1-715WAC
    PoE+ on all ports (30W per port)
    One PWR-C1-1100WAC or two PWR-C1-715WAC
    Two PWR-C1-1100WAC or one PWR-C1-1100WAC and one PWR-C1-715WAC
    http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3850-series-switches/data_sheet_c78-720918.html
    Hope this helps.

  • Replacement antennae for Cisco 800 wireless series?

    Hi. A customer has a rather thick wall at their site. Itsmaking mincemeat of the signal to their 7921 IP phone. Can I attatch different antennae's to the 800 series router? specifically something omni directional?

    Hey Huw,
    Just to jump in for a minute :) Cisco does offer "low-loss" extension cables for sale (like the two listed below);
    AIR-CAB020LL-R
    20-ft. low-loss cable with RP-TNC connectors
    AIR-CAB050LL-R
    50-ft. low-loss cable with RP-TNC connectors
    Cisco Aironet Antennas and Accessories Reference Guide
    http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.html
    Hope this helps!
    Rob
    PS: They also come in 100 and 150 foot lengths.

  • Error Compilation MIBs Supported for Cisco UCS C-series software release 1.4(3) and later releases on IBM Director 6.3.2

    Hi,
    I have an IBM director 6.3.2 on a Windows Server 2008R2
    I try to install the MIB for manage Cisco UCS C-460 server.
    I downloaded the mib on the cisco ftp.
    the files extension was my. I cahgne it to .mib. For the moment I success to import some ones.
    But when I try to install Cisco-Unified-Computing-TC-MIB, I have got the error in the join file.
    Ho can I fix this issue...

    Hi,
    I have an IBM director 6.3.2 on a Windows Server 2008R2
    I try to install the MIB for manage Cisco UCS C-460 server.
    I downloaded the mib on the cisco ftp.
    the files extension was my. I cahgne it to .mib. For the moment I success to import some ones.
    But when I try to install Cisco-Unified-Computing-TC-MIB, I have got the error in the join file.
    Ho can I fix this issue...

  • HT4059 I am looking for The Hunger Games Triology Series for the Ipad. Doesn't anyone know if it is available for the Ipad 2?

    I am looking for the Hunger Games Series for the Ipad 2 is it available for the Ipad 2?

    I am looking for the Hunger Games Series for the Ipad 2 is it available for the Ipad 2?

  • Cisco Catalyst 3850 Series

    Can I use DC power supply for
    Cisco Catalyst 3850 Series?

    Unfortunately your post is off topic here, in the TechNet Site Feedback forum, because it is not Feedback about the TechNet Website or Subscription.  This is only one forum among the many
    that are on the TechNet Discussion Forums, and given your post, you likely chose the wrong forum.  This is a standard response I’ve written up in advance to help many people (thousands, really.) who post their question in this forum in error, but please
    don’t ignore it.  The links I share below I’ve collected to help you get right where you need to go with your issue.
    For technical issues with Microsoft products that you would run into as an
    end user of those products, one great source of info and help is
    http://answers.microsoft.com, which has sections for Windows, Hotmail, Office, IE, and other products. Office related forums are also here:
    http://office.microsoft.com/en-us/support/contact-us-FX103894077.aspx
    For Technical issues with Microsoft products that you might have as an
    IT professional (like technical installation issues, or other IT issues), you should head to the TechNet Discussion forums at
    http://social.technet.microsoft.com/forums/en-us, and search for your product name.
    For issues with products you might have as a Developer (like how to talk to APIs, what version of software do what, or other developer issues), you should head to the MSDN discussion forums at
    http://social.msdn.microsoft.com/forums/en-us, and search for your product or issue.
    If you’re asking a question particularly about one of the Microsoft Dynamics products, a great place to start is here:
    http://community.dynamics.com/
    If you really think your issue is related to the subscription or the TechNet Website, and I screwed up, I apologize!  Please repost your question to the discussion forum and include much more
    detail about your problem, that could include screenshots of the issue (do not include subscription information or product keys in your screenshots!), and/or links to the problem you’re seeing. 
    If you really had no idea where to post this question but you still posted it here, you still shouldn’t have because we have a forum just for you!  It’s called the Where is the forum for…?
    forum and it’s here: http://social.msdn.microsoft.com/forums/en-us/whatforum/
    Moving to off topic. 
    Thanks
    MSDN and TechNet Subscriptions Support
    Did Microsoft call you out of the blue about your computer?
    No, they didn't.

  • Looking for some BAPIs to do some simple things

    Hello I am looking for someone to help me identify some BAPI function modules that will get me what I need.  Here is the information that I need, if you are able to identify a function module I can use, please let me know:
    Identify if a quotation number exists in the system which a specific sales organization.
    Determine the sale price of a material for a specific customer
    A simplier way to identify the plant specific status of a material without using the MATERIALGETALL
    Identify if a specific customer used a supplied purchase order before
    Identify if a customer has been placed on credit hold
    Thanks,
    Kent

    hello Maxwell ,
    hhave a look at tcode BAPI , under MM application area.... u will get all BAPIs related to MM modules.
    Identify if a quotation number exists in the system which a specific sales organization.
    Determine the sale price of a material for a specific customer-->u need to ask your functional consultant , may be he is creating info record for that one?
    A simplier way to identify the plant specific status of a material without using the MATERIALGETALL-->use table MARC
    Identify if a specific customer used a supplied purchase order before.
    Identify if a customer has been placed on credit hold-->i think u can make use of tcode vkm4 or custome master data will have all these info.
    regards
    Prabhu

Maybe you are looking for