Looking for HP 5371A driver for Labview 6.1?

want to communicate with HP5371A by PC over GPIB port

I think that device is too old for finding a driver for labview. If you have all the GPIB command, it's easy to program. I made it for another type of instrument.
Benoit Séguin
Software Designer

Similar Messages

  • Looking for graphics adapter driver for Presario c700 video

    Looking for graphics adapter driver for Presario c700 video

    Please read the XP Downgrade Guide at the link below:
    http://h30434.www3.hp.com/t5/Notebook-Operating-sy​stems-and/General-XP-Downgrade-Guide-for-HP-Laptop​...
    The guidance for installing XP on your model series can be found under the section labeled 2. Moderate Models.

  • I am looking for a Mac driver for a Muratec MFX 1430 printer/fax/copier.  Is there one out there for a Mac?

    Looking for a Mac driver for a Muratec MFX-1430 printer/fax/copier
    is there such an animal out there?

    http://www.muratec.com/new/support/drivers.asp does not appear to support that model at all on the Mac.
    Some open source drivers* may exist to support it.
    * Links to my pages may give me compensation.

  • Where do I go for a safe driver for the Mac for use with Altec Lansing Technologies IMT227 OrbitM Ultra Portable Speakers?

    Where do I go for a safe driver for the Mac for use with Altec Lansing Technologies IMT227 OrbitM Ultra Portable Speakers?

    This is an Altec Lansing IMT227 OrbitM etc
    Is this what you have?
    Here is the specification, please note, no USB
    You are either mistaken or talking about a different model.

  • Looking for HP E1725C driver for Labview 6.1?

    want to communicate with HP E1725C by PC over GPIB port"

    I haven't been able to find a driver for this instrument anywhere. You may want to contact HP and see if they have one, though it does not look like they do. You will probably need to access it directly through GPIB calls. Use the GPIB VIs to send strings which the instrument accepts. It should have come with a manual or something which supplies the valid strings. Just use those along with the GPIB VIs (actually, I would suggest using VISA) to build your application.
    J.R. Allen

  • Looking for a serial driver for an agilent 4395A to work with labview

    Can only find one for gpib I have no interface for gpib on my PC but i do have a rs232/gpib converter and was wondering if I could get a serial driver for the agilent 4395A for this.
    Thanks

    I've only used the RS232/GPIB converter to go from a GPIB bus to a serial instrument so I can't speak for going the other direction but I would give it a try. However, you have big problems with the driver if its the same one I just downloaded from NI. It's not really what I would call a driver at all but an application program meant to be used stand alone. There is no breakout of instrument functions into subVIs and none of the controls or indicators are on the connector so you can't even use the high level app as a subVI without a lot of work. It is a contributed driver but I'm surprised NI accepted it because it doesn't follow any of the published rules for an instrument driver. It's not even a good example of program design, imho. There is a VISA dr
    iver available from Agilent here and I would try that instead. To use a VISA driver with a serial port, you just specify the VISA resource name for that port instead of the GPIB resource name. For example, a GPIB resource name of an instrument with an address of 5 would be "GPIB::5::INSTR". To communicate to your instrument over com port 1, the VISA resource name is "ASRL1::INSTR". If the instrument has a serial port in addition to the GPIB, you could also try skipping the converter. Some VISA drivers work fine either way.

  • Looking for Keyence Instrument driver for LV.

    Looking for instrument driver for LV developed for the Keyence LS-7500 series micrometer. Has anything seen any or done this already? Any help would be greatly appreciated. BTW I have already checked NI's listing of instrument drivers to no success.

    Hello-
    There are no drivers listed for this instrument at http://ni.com/idnet. You may want to contact Programmed Test Sources to see if they have a LabVIEW driver for their instrument. If they don't, you can easily create a low-level driver by configuring an I/O assistant VI for each function in the manual. Once you have this low level driver you can just combine functions to make higher level VIs. Alternatively, you can hire an Alliance Member to write an driver for you.
    Alliance Member Directory
    http://www.ni.com/alliance/alliance_member.htm

  • I am looking for a backup drive for my macbook pro, any suggestions?

    I have a macbook pro and I am looking for a backup drive.  There are so many out there and I would like suggestions for which one to purchase.  Thanks!

    Pretty much any drive will work, but for a laptop, you might like to get a portable drive (doesn't require that you connect it to power) with USB3. Thunderbolt drives are also available, but they're more expensive and no faster than USB3 for a single hard drive.
    I personally like the Lacie rugged series: http://store.apple.com/us/product/H9377ZM/A/lacie-1tb-rugged-hard-drive-triple-u sb-30-5400-rpm?fnode=5f
    If you shop around you should be able to get it a little cheaper than Apple's prices.
    Matt

  • Looking at External SSD Drive for Lightroom Editing - How Can I Set This Up and Which Drive?

    I'd like to purchase an external SSD drive for Lightroom editing and am hoping somebody can provide a recommendation for me.
    I'm using a FW800 G-Drive to store my Lightroom Library and have been using this drive to edit.  I'd like to add an external SSD drive for editing photographs an am looking for recommendations on which drive and the best way to set this up.  I plan on having a 3rd (and maybe 4th) to save both the FW800 files and working SSD drive files as a backup.
    Any recommendations are sincerely appreciate. 

    I believe I was loading a preview file to 100%.  I think maybe I should just use what I have and work with it.  It's much faster than my 7 year old MBP performed that's for sure.
    I was just wondering if I could spend a few hundred for an external Thunderbolt or USB 3 drive to speed up my productivity.  With the full time job and the kids, I have a little time to work on photography.  I'd love to increase my output.  I'm more than willing to spend the money on the TB or USB 3 if it would help.
    The specs on the camera say 24.1 million pixels:  24.6 MB.  The raw files are
    NEF (RAW): 14 bit, compressed

  • Looking for a hard drive for a 2007 Macbook Pro

    I am looking around to replace my 160 gig hard drive for something larger.
    These are my choices:
    Hitachi 500GB Travelstar SATA 7200 RPM
    Hitachi Travelstar 5K500.B - 500GB 2.5" SATA 5400 RPM 8MB
    Fujitsu MJA2500BH-G2 500GB 5400 RPM 8MB
    I am just looking for something that won't wear down the battery, vibrates or produce some noises. Some speed increase would be nice if possible.
    I may pick the Hitachi 500GB Travelstar SATA 7200 RPM. But I am not 100% sure if this is a good drive or not.
    Message was edited by: Sean Coon

    I would choose anything that Other World COmputing would recommend.
    But before I swapped out to a 500GB drive, I would make sure I had redundant backup plans in place: both an external local drive, and offsite backup.
    500GB is an awful lot of data to lose when the drive fails. And it WILL fail at some point.
    What can you possibly fill up 500GB with? If movies or music, that stuff may be better off on its own, small, sleek, 7200RPM hard drive all the time (plus an offsite backup). If you're editing movies, the professionals don;t use their main drives for that - they use quality external drives for editing and storage (plus, of course, an off-site backup).
    Yes, I upgraded my MacBook Pro's hard drive to 200GB (original 7200RPM option was only 100GB). But I cannot fathom - ME, personally - filling up my MacNookPro's internal drive with 500GB of important data. I have a music drive, and work on other large work files on external 7200RPM drives.
    Whatever you do, please have reliable, regular backup schemes in place.
    Clint Bradford

  • Looking for external hard drive for Mac book air

    I'm looking for a external hard drive for my Mac book air

    What features are important to you?
    Size?
    Capacity?
    Speed?
    Price?
    Reliability?
    HDD or SSD?
    Desktop or portable?
    Just about any USB external drive will function properly, with only a few exceptions. I would avoid the Toshiba Canvio using USB 3.0, as it has been the topic for numerous threads here wherein users have had problems using them with the MacBook Air.
    My personal favorite external HDD right now is the Seagate GoFlex, as I can use them with the Thunderbolt adapter. But I have been eyeing the new LaCie Rugged Thunderbolt.
    For super speed, I use a Crucial model M4, either using the Seagate Thunderbolt adapter, or I have some mounted in USB 3.0 housings.

  • Looking for HP Laserjet driver for OSx.10.8.2

    I need a printer driver for an HP Laserjet 1200 or HP Laserjet 1300. HP says it's Apple's responsibility and Apple says it's HP's responsibility.
    Any help appreciated. Thanks

    Hi,
    The HP Laserjet 1200 do compatible with Mountain Lion:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01664444 #N2471
    Try removing any instalnce of the drivers and then check for Software Update:
    Go to Computer > Macintosh-HD > Library > Printers and move the HP folder to the trash.
    Browse into PPDs > Contents > Resources. search for 1200 within the folder. move the drivers to the trash and restart your Mac.
    Next go to Print & Scan and reset the printing System:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01371980
    Finally try connecting the printer again and check for any difference.
    Shlomi

  • Im looking how to find driver for Printer HP 2300 driver window 8 (64BIT) PLEASE help !!! stuck

    Hi ,
    I need help how to find driver for my old printer HP 2300d I use USB Cable for my Laptop window 8 (64 bit)
    help I am stuck can't print anything.
    Kim

    Hi, Welcome to hp forums and enjoy your stay, feel yourself like home here!
    I am very sorry to hear this, I will try my best to help you, I am always glad to help!
    Please follow the steps i provided below:
    1. http://windows.microsoft.com/en-ca/windows7/automatically-get-recommended-drivers-and-updates-for-yo...
    Now refer to the below link and right click your printer device
    2. http://pcsupport.about.com/od/windows-8/a/update-drivers-windows-8.htm
    Sorry because of different timezone I might not be able to help/reply you right away.IF that happens I deeply apologize!
    **Click the White thumb if you like the answer.**
    **Please mark Accept As Solution if it solves your problem and only solves your problem, if you have any more questions please ask, this also helps others to solve related issues.**
    Feel yourself like home here, we are all happy to help, if you have an question reply or start a topic or pm me or an expert.

  • Driver for DVD rom drive for dv6308nr

    Does anyone know where to find the driver for an HP laptop dv6308nr cd/dvd rom drive?  I looked it up on the site and it isn't listed under the available drivers.  Maybe I am missing it????

    Hi,
    which Notebook do you own and which system is used?
    Normally you don't need an extra DVD driver except DVD RAM is used!
    Is there occured any failure with the DVD? Why can't you use it anymore?
    Please write down some further informations!
    Bye TOK

  • Apple physically replaced the HD on my Imac.  I backed up everything on a Seagate Go Flex Desk for Mac external drive for Mac.  I went through the motions to restore my Iphoto Library back to my computer. Can't find them!!!!!

    Apple replaced my hard drive on my Imac.  I'm lucky I backed up everything on a Seagate Go Flex Desk for Mac external drive via Time Machine .  I followed directions in order to restore my iphoto library , but I can't seem to find it on my computer.  Are the files locked?

    No reason to assume they are locked. The library will be restored to the location it was backed up from, unless you specified somewhere else. Have you looked in your Pictures Folder?

Maybe you are looking for