Looking to add more BRI Lines

Hello
I'm looking to upgrade a Cisco 2921 system to add additional BRI lines.
The base system is a C2921-CME-SRST/K9 bundel (that has a PVDM3-32)
The existing HWIC slots contain two VIC2-2BRI-NT/TE modules, and one VIC3-4FXS/DID module.
(That's two 2-port BRI modules, and one 4port voice/fax module)
Currently, there are 3 BRI lines coming in, and 2nd port on second module is shutdown (according to cisco specs).
What should I be looking at if we want to add 3 more lines and incorporate conferencing? (as there are issues with conferencing now - possibly due to DSP availability?)
Can we add more modules? Should we replace the 2 port BRI modules with 4 port ones? Do we need to add more PVDMs?
Thanks in advance.

Beware the four port BRI modules (HWIC-4B-S/T) as they only support data and not voice.
There is a module which may be of use at the URL below:
http://www.cisco.com/en/US/partner/prod/collateral/modules/ps3115/product_data_sheet0900aecd8016c1c6_ps5855_Products_Data_Sheet.html
The basic module (EVM-HD-8FXS/DID) provides 8 FXS/DID ports and it can accomodate two expansion cards. There is a four port BRI expansion module available (EM-4BRI-NT/TE) so this card could potentially give you 8 x FXS/DID and 8 x ISDN BRI.
It was originally designed for the 2800 routers and needs an adapter (SM-NM-ADPTR) for use in the 2900 series. It is also old so may be due an End of Sale notice soon.
The card does not provide any DSP resources so you may need to add extra PVDM3 resources to your 2900.
As mentioned by Jonathan I would have a think before commiting to lots of BRI circuits. PRI or SIP is likely to be more cost effective in the longer term.

Similar Messages

Equium A100-303: looking to add more RAM

Hello,
I recently bought an A100-303 equium notebook and am lookin to add more RAM. I was just wondering if it needs to be buffered or unbuffered or does it matter?
I currently have 1gb of ram (512 + 512 as its a dual core processor) and am looking to upgrade to 2gb (1024 + 1024). I know the type is PC4200, 200 pin, SODIMM.
Also where would be the cheepest place to buy these? Thanks.

Hi
> was just wondering if it needs to be buffered or unbuffered or does it matter
Well, Toshiba recommended using own memory modules like PA3411U-2M1G but I dont find any information if the module supports ECC (means buffered) or Non-ECC (means non buffered)
In my knowledge the ECC-buffered memory is about 30 percent slower as the Non-ECC modules.
Its your choice what you will buy but I would recommend buying a brand name module.
I know, the no-name modules are cheaper but brand modules are much faster and the performance and quality is better as no-name modules.
So googel a little bit and you will find many online offers. Compare simply the prices

I am looking to add more USB ports to the back of Mac Pro

Will this fit the Mac Pro? Any other recommendations?
http://www.maczone.com/site/product/index.html?id=001392119

I don't know the specs. on the early Mac Pros, but the latest ones all have PCI Express. That's why I said "if".
If they all have PCI Express, then you'll need the Express version.
I have the USB Express version card in my Mac Pro right now.

UME & LDAP setting, Cannot add more UME MII users in NW7.1/MII 12.1.5

We're using MII 12.1.5 (Build 85), configured with standard DB+LDAP authentication.
Data source: MicrosoftADS (Deep Hierarchy) + Database
Data Source File Name: dataSourceConfiguration_ads_deep_writable_db.xml
I need to a dd some users to the system, not existing in the Active Directory list (i.e. temporary access). When I try to add them to the UME database, the system is telling me I'm in trouble.
[LDAP: error code 50 - 00000005: SecErr: DSID-031521D0, problem 4003 (INSUFF_ACCESS_RIGHTS), data 0 ]
Where should I look to elevate my rights, since I'm already logging in with the highest access on the system?
Regards,
paul.

Thanks Udayan,
If NW wants to add an user in AD, then the AD user specified in the configuration has to have enough rights to do that (which doesn't unfortunately, and won't have ever). I am looking to add more users in UME, not in AD.
In my case, the Active Directory structure extends on multiple levels. For example, there is an AD server for corporate and then another AD servers for plants. The users in the plants are able to connect to the plant MII using their local credentials, but they cannot authenticate to the corporate MII development box (not being visible from the corporate AD leaf). Therefore, being a handful of names, I was thinking to add them in UME and bypass the AD authentication in their case (not being an AD expert) for the development server.
Who said networking is easy? I can't remember ..
j/k
paul.

In Apple Mail, I cannot add more than one address to the "To" line

In Apple Mail, I cannot add more than one address to the "To" line by typing just the initial

HHow are you. Trying to add the second address? Normal procedure after the first address is to type a comma, then start typing the name for the second address.

Looking for a way to add more signatures

I'm creating a form that has a standard orginator and approver signature blocks. Is there a button or another way to add additional approver signature blocks if needed? Any help on this would be greatly appreciated. Thanks!

Hi Catherine -
Depends on the type of signature block you are looking to add. If a secured digital signature, then those do not allow you to add in dynamically from what I see. If the signature block is just a holding spot for an ink signature then you could put in code to duplicate a subform that contains the signature block.
A work around for a digital signature is to create several signature blocks and make them hidden until a check box is selected, or something along those lines.
If ink signature blocks then put your signature block objects in a subform, call it "SigBlock" for example. Make sure the form is setup as dynamic, and set the subforms as flowed to avoid overwirting any info underneath. You could place a button that states something like "Click to add signature" and put this code under the CLICK event:
Page._SigBlock.addInstance(1);
xfa.form.recalculate(1);
If digital signatures then you'll want to embed Positioned subforms inside flowed subforms so that all materials flow, but the actual digital signature is in a fixed location. Be sure to set your FILE - FORM PROPERTIES - DEFAULTS to "Manually" on scripting and check the box titled "Enforce Strict Scoping". Then setup all your digital signature blocks, and when all formatted properly you could add in some hidden checkboxes that are set to CALCULATED, and have code under those that check status of a user checkbox to add signatures. If != 1, then the calculated field could tell the form to hide the signature block. If == 1 then the block unhides. Inside that block can be another user selected checkbox to add another signature, another hidden calculate field, etc. I would do this instead of setting up hidden properties in the form INITIALIZE setting since you may not want to hid those blocks everytime the form is loaded.
A tad complicated, but it works!
Jim

I am using iPhoto 11 mail and cannot add more than one recipient in the 'to' line. When I put a comma in, the recipient's address is deleted. If I use ' ' with more than one recipient the save grays out. Any thoughts?

am using iPhoto 11 mail and cannot add more than one recipient in the 'to' line. When I put a comma in, the recipient's address is deleted. If I use '< >' with more than one recipient the save grays out. Any thoughts?

I figured it out. I needed to fix some errors in my account information. It works fine now.

How to assign Line Number for Lines when click on Add More Lines

Hello All,
Kindly help me to assign line number for the lines which are added through Add More Lines button on an Advance table. If user clicks on the button Add More Lines then there are 5 lines get inserted at a time but I am not able to handle the line number for them.
Similarly, if user delete any of the line then I need to re-order them.
Kindly help and share if there is any sample code.
Thanks,
Sandy

Hi,
Check if this link helps you :
Re: How to display serial numbers in the results table region
--Sushant

How do I add a second line at home?

I've been trying to find the answer to this question online and have struck out. Verizon's website says that to add a second line at home you can log into your account, go to "My Profile," click on "Lines & Accounts," and then click on "Add Second Line" (or something like that....unfortunately today Verizon's online support system is claiming that online support is not offered in Virginia). When I go to "Lines & Accounts," however, it does not give me the option to add a line—it will only allow me either to de-register my current phone number from online account access or to register another billing number for online access.
At the moment I am not certain I actually want to order the second line—I just want to price it out to determine whether I would rather get a second line or switch to VOIP service with dry loop DSL. This is why I'd rather run through my options online instead of having to call customer service—it's easier and more efficient to be able to view the options on the screen instead of having to take notes while talking to someone.
Does anyone know if there is a way to price this out online? Verizon's site has been the target of much profanity from me due to the apparent absence of this feature and due to this utterly ASININE statement that appears when I try to get online support: "Select a Service for Online Help/Verizon does not offer this service in Virginia. You can search or browse Phone Support for the services." I mean, come on, is that some sort of joke??!!
(I use a Bang & Olufsen two-line cordless phone system tied to a BeoLine base unit, and I've already confirmed that the phone jack into which the BeoLine is plugged is indeed wired for two lines. So that's not an issue.)
Message Edited by 1995hoo on 07-29-2009 09:47 AM

Hello,
I've already seen your post on StachExchange and answered you there. So here's the answer:
All you need to do is to add solid to the border-bottom property, so it would look like this:
.groupheader {
padding-left: 10px !important;
padding-right: 5px !important;
border-bottom: 1px #000000 solid ;
Mohamed Derhalli
SharePoint Consultant
Blog: SharePoint Thoughts
Twitter:
LinkedIn:

Row Level PPR in Advanced Table with Add More Rows Button

<br>
I have programmatically fired PPR event on MessageChoice. But it is in Advanced Table with
Add More Rows Button. When the value is changed in MessageChoice I Show/Hide Custom LOV
through SPEL like this ${oa.BioEmployeePVO.EmpManagerRender} .
But it is <b>hiding the all the ROWS</b> not just the row where the value has been changed.
I even tried with this code and get NULL for rowReference.
String rowReference = pageContext.getParameter(OAWebBeanConstants.EVENT_SOURCE_ROW_REFERENCE);
In Processrequest()
String pageName = pageContext.getRootRegionCode();
     Hashtable params = new Hashtable (1);
     params.put ("param1", pageName);
     Hashtable paramsWithBinds = new Hashtable(1);
    paramsWithBinds.put ("param2",new OADataBoundValueFireActionURL (mcb, "{$AttendeeType}"));
    mcb.setFireActionForSubmit ("empPositionChange", params, paramsWithBinds,false, false);
In ProcessFormRequest() {
if ("empPositionChange".equals(pageContext.getParameter(OAWebBeanConstants.EVENT_PARAM)))
      String rowReference = pageContext.getParameter("param2");
    //    String rowReference = pageContext.getParameter(OAWebBeanConstants.EVENT_SOURCE_ROW_REFERENCE);
     Serializable[] parameters = { rowReference };
      am.invokeMethod("handlePositionChangeEvent", parameters);
<br>

HI Kumar,
Answer to your last post is "yes".
Now to your doubt regarding the code:
Hi Anna
I am trying to understand your code.
FireAction firePartialAction = new FirePartialAction("fireHideEvent"+(i/noOfTlaColSpan));
HideImgBean.setAttributeValue(PRIMARY_CLIENT_ACTION_ATTR,firePartialAction);
1. What is this i/noOfTlaColSpan ?
:)Forget abt this in your case it should be the event name which u r firing and capturing the it in the PFR.
Like FireAction firePartialAction = new FirePartialAction("YOurEventName");
and in PFR u can capture tht as:
if("YOurEventName".equals(pageContext.getParameter(EVENT_PARAM)))
//your logic to invoke AM method
2. I believe this HideImgBean would be MessageChoice for me?
:)Yep ur right
3. This brcdOhInventoryViewUpdateVOImpl would be the Custom PVO(Extending Seeded Base VO)
I create by adding the transient attributes?
:)Yep ur right
4. I cannot understand this code. Could you explain.
:)Please look at my comments in some of the lines .I have explained wht i am doing
if(updateIter==null)
updateIter[0]= invViewVO.createRowSetIterator("updateIter");//This initViewVo should be ur custom VO object
if(cnt>0)
updateIter[0].setRangeStart(0);
updateIter[0].setRangeSize(cnt);
for(int i=0;i<cnt;i++)
row = (brcdOhInventoryViewUpdateVORowImpl)updateIter[0].getRowAtRangeIndex(i);
String selectFlag=(String)row.invokeMethod("getPartNumber");//This getPartNuber should be replaced by the Prim Key inoke methd of ur VO
if(RowID.equals(selectFlag))
//This is my logic to set the transient attributes based on the msgChoiceBean value ..u have to pass the value when u invoke this method
if(reserveMethod.equals("BINARY"))
System.out.println("In Binary");
Boolean bVal= new Boolean("false");
Serializable sr[]={bVal};
Class []methodParamTypes = { bVal.getClass() };
row.invokeMethod("setshowreservetxt",sr,methodParamTypes);
Boolean bVal1= new Boolean("true");
System.out.println("bVal1"+bVal1);
Serializable sr1[]={bVal1};
Class []methodParamTypes1 = { bVal1.getClass() };
row.invokeMethod("setShowreservemsgchoice",sr1,methodParamTypes1);
break;
In my AM I am doing this. Am i doing right?:)Yep u r right
BioPrescribersPVO is the custom VO(extending seeded base VO).
public void handlePositionChangeEvent(String param)
OAViewObject vo = (OAViewObject)findViewObject("BioPrescribersPVO");
OARow row = (OARow)findRowByRef(rowReference);
if (row != null)
String position = (String)row.getAttribute("AttendeeType");
if (("PRESCRIBER".equals(position)) )
// BioEmpManagerRender is the transient attribute in BioPrescribersPVO.
row.setAttribute("BioEmpManagerRender", Boolean.TRUE);
row.setAttribute("BioPresManagerRender", Boolean.FALSE);
else
row.setAttribute("BioEmpManagerRender", Boolean.FALSE);
row.setAttribute("BioPresManagerRender", Boolean.TRUE);
} // end handlePositionChangeEvent()
// Initializing the custom VO
/*No need to initialize the VO because this is not a PVO(Propeties View object)
U r just using the existing VO and tht vo shloud have a primary key.Tht way u can match the rowref u r getting with the actual row from the View object*/
public void init()
OAViewObject appPropsVO = (OAViewObject)getBioPrescribersPVO();
if (appPropsVO != null)
if (appPropsVO.getFetchedRowCount() == 0)
appPropsVO.setMaxFetchSize(0); appPropsVO.executeQuery();
appPropsVO.insertRow(appPropsVO.createRow());
OARow row = (OARow)appPropsVO.first();
row.setAttribute("RowKey", new Number(1));
handlePositionChangeEvent("");
} // end init()
Thanks
Anna

Cant add more data points to numbers chart

I have a 2 axis 2D graph. I would guess i have about 150 data points along the y axis for both lines on the chart. I have been updating the chart each week no probem with new data points. However today, i can only seem to add a few more points - when i try to add past a certain amount of data points, the last 20 or so data points are removed from the series?
It simply will not allow me to add more data?
Any help on this matter would be greatly appreciated as the charts are for use in my business

Hi Jerrold, thanks for the reply.
I dont have category labels. I have a 2 axis 2D chart, with a line series and an area series on the chart. I add new data to the chart each week by clicking on either the line or the area series on the chart, then going to my data table beside the chart, and by holding apple command button and clicking on the relevant cells to add to the charts. As of this weeks adding, it starts of as usual, adding the cells to the line and area series, and thus adding data onto the existing chart and extending it out to the right, as it normally would. However, i can only add a certain amount of new cells (data points) to either the line or area series. When i go to add more, a very strange thing happens. The series switches from all the cells that are highlighted blue, to another table i have on the same document??? If i look at the Inspector in the Data box under the series tab, the data goes from the typical 'Table 1 :: D18', (highlighted in blue, to the following weird data point : 'D38,SFTGlobalID_CB7D88F601784CAC8DD283ECA59CFB41 :'
Its worth noting that although i an working on a brand new macbook pro, numbers has crashed on me a number of times when adding large amounts of data to the chart The table has 1,120 rows, and 11 columns. Only 1 in every 5 or so rows are plotted (on y axis), so roughly 200 or so data points for both line and area chart are plotted. And only 1 column is used for each chart. Thus i have 11 charts on the one numbers document. Is it a case of too much for numbers to handle?
I have just deleted all the y axis data for the area series for one chart, and added all the data from the whole table again, (rather than just adding this weeks to last weeks, which is where i saw the problem in the first place) to see if it made a difference. But none. Once i got to a certain point, if i add one more cell data point to the chart, the exact same thing happened as above - the highlighted data switched from what i had been highlighting the whole way down the table, to an entirely different table in the same workbook.
Any ideas would be greatly appreciated.

How do I add more than 10 options to the drop down menu?

Presently, I'm only able to give ten options but many of my items have 20-30 options.How do I add more than ten options to the drop down menu?

BrazenChick wrote:
Presently, I'm only able to give ten options but many of my items have 20-30 options.How do I add more than ten options to the drop down menu?
It depends on the type of option. If each option has a separate price, then I don't know of a way to add more than 10 options since those options with the prices are encoded into the button id. (Well, you could encode the information yourself with PayPal's API, but that is way more involved than I've been willing to tackle.) If you have more than 10 options such as color, scent, etc that don't affect the price, then you can edit the code you have added to your website to add additional items in the list. For example, suppose you had options "red" and "green", the relevant part of the code would look something like this: <select name="os0">
<option value="red">red </option>
<option value="green">green </option></select> If you want to add the option "blue", you would insert the line : <option value="blue">blue </option> before the closing </select> tag. More than 10 options won't be saved in the PayPal button creator, but it will work just fine in your website since this type of option isn't encoded in the id.

Anyway to "UN" Ken Burns stills globally or as default bringing in jpeg's? New to iMovie. I have 3 titles that build. First is logo, add prod't name second line, add date 3rd line. They shift when dissolving between them. Title function NG for this.

Anyway to "UN" Ken Burns stills globally or as default bringing in jpeg's? New to iMovie. I have 3 titles that build. First is logo, add prod't name second line, add date 3rd line. They shift when dissolving between them. Title function NG for this.
The people at the Apple store gave me a long, tedious workaround which is open Pages and bring in logo. Export it as a PDF. Open the PDF in Review and then "Save As" a jpg to the desktop and drag and drop into the imovie. Even with this process, the text will sometimes shift. When it works, it looks good, the logo comes up, then the second line fades in under it as part of the build and then the third line completes the graphic. It would something this easy and straight forward would be easy.
HarveyV

I did the work around for the titles/jpg's in this short video.
I'll try your fix on the next one. I have 22 short 3-5 minute videos to produce
and I'm on number 5. This should save me a bunch of time.
It would appear that you know more than the guy at the Apple Store.
Thank goodness for on-line forums.
I already tried fixing them individually as you suggested,
by going the crop/fit route. However, even then,
the second in the series had always shifted.
The first and the third images lined up, but not number 2..
So I brought in all the images, (1, 2 and 3).
and then the 2nd image again and put it in the third position
in the sequence on the time line. I deleted the "original" 2nd image.
So I had 1, 3, then 2. Then I dragged and dropped the correct number two
into position two and it worked. So what happens is that the
client logo appears, then that stays put and the next line dissolves in
and then the third dissolves in. They are three separate titles, but they
are aligned perfectly so that they build as I dissolve between them.
I think the problem with the edit copy route would be that while
I could edit/copy the logo, I couldn't position text through the
iMovie text function exactly as it only gives you middle or bottom third etc.
Each title with the product name is positioned individually depending on
length and number of lines. By going through Pages, I can position the logo
and the text exactly. Also, some logos are horizontal, while others
are square etc., so text positioning is crucial.Anyhow,
I'll try the global approach for the next one and see how that works.
Thanks very much for your insight and especially for your prompt reply.
I trust you're inside on this gorgeous July 4th because you're
making money on your computer. ;-)HarveyVOn 7/4/2011 3:57 PM, Apple Support Communities Updates wrote:
> Apple Support Communities <https://discussions.apple.com/index.jspa>>>> Re: Anyway to "UN" Ken Burns stills globally or as default> bringing in jpeg's? New to iMovie. I have 3 titles that build.> First is logo, add prod't name second line, add date 3rd line.> They shift when dissolving between them. Title function NG for...>> created by AppleMan1958 > <https://discussions.apple.com/people/AppleMan1958> in /iMovie/ - View > the full discussion > <https://discussions.apple.com/message/15552380#15552380>> ------------------------------------------------------------------------>> I am baffled by what you are asking...but if you are asking how to > turn off the Ken Burns effect, you can do it for future photos you add > by going to File/Project Preferences and setting the default initial > photo placement to FIT or CROP rather than Ken Burns.>> For a global change on photos that are already in your project, pick a > photo. Open the Rotate, Crop, Ken Burns Tool. Select FIT or CROP. > Exit the tool. Now select this same photo and EDIT/COPY.>> Now, EDIT/SELECT ALL.>> Finally, EDIT/PASTE ADJUSTMENTS.../CROP ADJUSTMENTS.

How can I add more than one same spry menu (eg. collapsible menu) with in different styles (font size, color, background, etc) on current page?

How can I add more than one same spry menu (eg. collapsible menu) with in different styles (font size, color, background, etc) on current page?

Hi Nancy,
This screenshot was only for imagination. A part of the code (not all) is below. In the code there are some background images but they are not seem in live mode.
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
<title></title>
<link href="css/my_site.css" rel="stylesheet" type="text/css" />
<link href="SpryAssets/SpryTabbedPanels.css" rel="stylesheet" type="text/css"/>
<link href="SpryAssets/SpryCollapsiblePanel.css" rel="stylesheet" type="text/css" />
<script src="SpryAssets/SpryTabbedPanels.js" type="text/javascript"></script>
<script src="SpryAssets/SpryCollapsiblePanel.js" type="text/javascript"></script>
<style>
#CollapsiblePanel1 .CollapsiblePanelOpen .CollapsiblePanelTab {
    background-color: #003366;
    font-size: 18px;
    line-height: 52px;
    color: #FFF;
#CollapsiblePanel1 .CollapsiblePanelTabHover .CollapsiblePanelTab {
    background-color: #003366;
    color: #FFF;
    text-shadow: 1px 1px #000;
    font-weight: bold;
    line-height: 52px;
#CollapsiblePanel1 .CollapsiblePanelClosed .CollapsiblePanelTab {
    background-color: #C3CFDF;
    border-radius: 5px 5px 0px 0px;
    color: #999
    text-shadow: 1px 1px #000;
    font-family: "Trebuchet MS", Arial, Helvetica, sans-serif;
    font-size: 18px;
    font-weight: bold;
    line-height: 52px;
#CollapsiblePanel2 .CollapsiblePanelOpen .CollapsiblePanelTab {
    background-image: url(images/international.jpg);
    background-repeat: no-repeat;
    font-size: 18px;
    line-height: 52px;
    color: #FFF;
#CollapsiblePanel2 .CollapsiblePanelTabHover .CollapsiblePanelTab {
    background-color: #003366;
    color: #FFF;
    text-shadow: 1px 1px #000;
    font-weight: bold;
    background-image: url(images/TR_Col-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
#CollapsiblePanel2 .CollapsiblePanelClosed .CollapsiblePanelTab {
    background-color: #C3CFDF;
    border-radius: 5px 5px 0px 0px;
    color: #999
    text-shadow: 1px 1px #000;
    font-family: "Trebuchet MS", Arial, Helvetica, sans-serif;
    font-size: 18px;
    font-weight: bold;
    background-image: url(images/TR_Gray2-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
#CollapsiblePanel2 .CollapsiblePanelContent {
    background-color: blue;
#CollapsiblePanel3 .CollapsiblePanelOpen .CollapsiblePanelTab {
    background-image: url(images/TR_Col-WEB.png);
    background-repeat: no-repeat;
    font-size: 18px;
    line-height: 52px;
    color: #FFF;
#CollapsiblePanel3 .CollapsiblePanelTabHover .CollapsiblePanelTab {
    background-color: #003366;
    color: #FFF;
    text-shadow: 1px 1px #000;
    font-weight: bold;
    background-image: url(images/TR_Col-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
#CollapsiblePanel3 .CollapsiblePanelClosed .CollapsiblePanelTab {
    background-color: #C3CFDF;
    border-radius: 5px 5px 0px 0px;
    color: #999
    text-shadow: 1px 1px #000;
    font-family: "Trebuchet MS", Arial, Helvetica, sans-serif;
    font-size: 18px;
    font-weight: bold;
    background-image: url(images/TR_Gray2-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
#CollapsiblePanel4 .CollapsiblePanelOpen .CollapsiblePanelTab {
    background-image: url(images/TR_Col-WEB.png);
    background-repeat: no-repeat;
    font-size: 18px;
    line-height: 52px;
    color: #FFF;
#CollapsiblePanel4 .CollapsiblePanelTabHover .CollapsiblePanelTab {
    background-color: #003366;
    color: #FFF;
    text-shadow: 1px 1px #000;
    font-weight: bold;
    background-image: url(images/TR_Col-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
#CollapsiblePanel4 .CollapsiblePanelClosed .CollapsiblePanelTab {
    background-color: #C3CFDF;
    border-radius: 5px 5px 0px 0px;
    color: #999
    text-shadow: 1px 1px #000;
    font-family: "Trebuchet MS", Arial, Helvetica, sans-serif;
    font-size: 18px;
    font-weight: bold;
    background-image: url(images/TR_Gray2-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
#CollapsiblePanel5 .CollapsiblePanelOpen .CollapsiblePanelTab {
    background-image: url(images/TR_Col-WEB.png);
    background-repeat: no-repeat;
    font-size: 18px;
    line-height: 52px;
    color: #FFF;
#CollapsiblePanel5 .CollapsiblePanelTabHover .CollapsiblePanelTab {
    background-color: #003366;
    color: #FFF;
    text-shadow: 1px 1px #000;
    font-weight: bold;
    background-image: url(images/TR_Col-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
#CollapsiblePanel5 .CollapsiblePanelClosed .CollapsiblePanelTab {
    background-color: #C3CFDF;
    border-radius: 5px 5px 0px 0px;
    color: #999
    text-shadow: 1px 1px #000;
    font-family: "Trebuchet MS", Arial, Helvetica, sans-serif;
    font-size: 18px;
    font-weight: bold;
    background-image: url(images/TR_Gray2-WEB.png);
    background-repeat: no-repeat;
    line-height: 52px;
</style>

Verizon To Add More .Tv Channels. Sony Movie Channel To Be Added.

Verizon is set to add more .tv channels where two of them are on their way. Legacy .tv a .tv channel from byron allen's entertainment studios will be added to the fios guide and another channel called "justice central .tv" is on its way where it is expected to be made available for fios customers soon. Justice central .tv is a channel that is all about court tv shows where what viewers will have an opportunity to watch are programs like "we the people with gloria allred" where she dishes out her own brand of justice to people who appear in her courtroom. It is a channel that will be all about judges yelling at plantiffs and defendants that will also have a lot of infomercials. That will make it 8 .tv channels where byron allen is also looking to create more .tv channels for verizon to add to their lineup since he has a contract with verizon to add any channel that he has to the fios guide. For the record verizon has entertainment studios .tv, pets .tv, recipe .tv, comedy .tv, my destination .tv, and cars .tv which won an emmy for "outstanding lifestyle program." Another channel that is on the way is the sony movie channel in hd where sony has already confirmed that the channel will be added in the next 2-3 months to the fios guide. Now i have never seen anyone make any requests for .tv channels and i have never seen anyone say that they wanted more of them to be added but that is going to change soon where not only will there be 8 but maybe by the end of the year there may be a total of 10,11,12 or maybe even 13. It all depends on how fast byron allen can create these channels because clearly verizon is willing to add as many of them as they can. There is a really long list of channels that fios customers have been asking for to be added to the guide where the competition has added them so it is not an outrageous request to ask verizon to at least match what the competition has to offer.

Which means FiOS is better than the other services, Bob!

Looking to add more BRI Lines

Similar Messages

Maybe you are looking for