Looking to buy an HDV deck

Hi,
I need to dub working copies of my master tapes. We shoot in HDV. Could anyone recomend some decent decks that copy HDV tapes?
Thanks,
Tom

You could buy a Sony M15, but a used HC3 would be way cheaper.

Similar Messages

Trouble with a SONY HDV deck HVR-M10U

I have a DSR-11 that operates thru firewire. It works properly. A client recently loaned me an HDV deck and gave me some HDV tapes to digitize. So I plugged that into the deck's Firewire connection. When I do the EZ setup for the HDV codec, it says it's not connected. Athe Mac Pro end I have a Firewire 400 cable end converted to Firewire 800. That works fine for the DSR-11. So now I don't know what to do. I'm thinking there's some way to capture without control using composite video out and RCA audio jacks. I have a decklink extreme card but I don't think it accepts composite video, only Y-in. I'm out of ideas.

When you choose HDV from the Easy Set Up, FCP looks to find an HDV deck.
If the HDV deck is set to down convert to DV, the deck identifies itself to the firewire bus as a DV deck and FCP reports not being able to find an HDV deck.
Not saying this is the problem, but it is something to check.
MtD

Unable to initialize HDV deck. Please make sure a deck is connected....

Ok, this is driving me nuts. I've done this before. I have a Canon HV20. I spent HOURS and HOURS on Sunday (two days ago) capturing 1.5 hours of video (DV, not HD) from my HV20 using iMovie09. Then spent more hours burning a DVD using iDVD09. Results were less than glamorous. Quite disappointing, video-quality-wise....
So today I reinstalled FCE 4.0 (HD) and decided to capture a few minutes of the same film and compare the results when making a DVD. My expectations are that it will look better. Naturally, I was hoping for the less-expensive, easier to use product (iMove09) would win, but so far, I can't compare because I keep getting "Unable to initialize HDV deck...". Folks, I have a firewire cable connected. I just used the same camera on the same cable on the same computer (macbook pro). the ONLY thing i changed was the software. Even switched back to iMovie for a minute to see if the cable still worked and sure enough, it's fine.
So, I'm blank on ideas here as to why "FILE/CAPTURE" in FCE would give me this error now. I'm waaaaaaaay open to ideas and even open to "stupid user error"... just tell me what it is....
This is soooooooooooo frustrating. Now I remember why I don't do video that often. Real pain in the butt sometimes...
Thoughts????

"Unable to initialize HDV deck...".
You seem to be trying to capture DV?
At the moment FCE is looking for a HDV camera and there is not one attached, a DV camera is.
Change the Easy Setup to the correct DV option to match the cameras output (audio and video), save, then try again.
Al

Final Cut Pro 7 not recognizing Sony HDV Deck on older 2008 version MacPro's

I am trying to connect a Sony HDV deck to Final Cut Pro version 7 on an older 2008 version MacPro. The problem was with the firewire mini port on the back i believe because i used a different deck which was the same model - but the only difference was it had a firewire 400 port instead of mini firewire port. Anyway, the deck with the 400 firewire port worked for logging and capturing, etc... (this also worked when i re-tested it on the 2008 MacPro) Im wondering if anyone else has had problems with the firewire mini port on the Sony HDV deck because it seems like almost every HDV deck i have with mini firewire has problems connecting to final cut pro or any editing application. I know now that the deck i had in question the mini port is not working correctly but is there a way to fix this or prevent the cable - deck from terminating the connection with the mini cable being used. I dont need an answer to the deck problem because i figured it out but just wondering if anyone has some insight on this deck problem. Thank you...
Kyle

>I dont need an answer to the deck problem ... just wondering if anyone has some insight on this deck problem
So you don't want an answer, just insight. OK, I'll give it a go. I've had several Sony VTRs with the 4pin Firewire port (proper name for what you refer to as "mini"), which is the same type of port that most DV and HDV cameras use as well. One of the main things you need to be wary of is plugging in and unplugging a Firewire cable while either the device or the computer is powered on. I know that marketing hype claims that Firewire is hot swap-able, but it really isn't safe to do so. The pins in both the 4 pin connector as well as the 6 pin connectors are very close together and if they aren't aligned exactly right with the socket, can easily cause arching and damage a Firewire port on either or both ends. Is that the kind of insight you were looking for?
-DH

Can't preview 1920x1080 timeline on HDTV via Sony HDV deck - help!

I am trying to play back from my 1920x1080 HDTV timeline (from FCP on MacBook) on an LG HDTV by connecting to a Sony HDV deck via firewire 800, and then going out from the deck via component to the tv – however, I am having problems not being able to get a clean video signal & it seems that the deck cannot process the video stream properly. After scouring the internet and various forums, the only conclusion that I can reach is that because the HD video needs to be processed, it is impossible to properly view the footage back via this method without something like a Blackmagic Decklink card/conversion syste. This is quite a big problem for me, as I will probably in the future have to use the same method just to play out to tape (on the HDV deck) and no matter what settings I have tried, it just doesn't want to work!
Any hints or tips to bypass this without the need for any other external hardware? Would something like a Mini DVI to VGA Adapter Cable help at all – we have one of those.

FW800 can't stream full uncompressed HD video, which is what the HDTV needs. You need an HDMI connection. You're going to need an AJA Knoa LHi or some other such card. You may want to look into a less expensive option such as the MXO2 if you only want to see the image on an HDTV and not on a qualified Production Monitor.
Going from FCP back to the deck is a totally different issue and not a problem. HDV is highly compressed so it can stream via FW connection. FCP using the Print To Tape function will take your Sequence and send a native HDV signal back to your deck, just when it captured from the deck.
HDTV will not be good enough for evaluating image quality and color correction, FYI. It will only give you an idea of what your vide will look like on that specific brand and model of HDTV.
DVI and VGA have nothing to do with what you're trying to do. They are only for going out to a computer monitor (not the same as a TV) or a projection system.

HDV Deck suggestion

I have a XL-H1 and am l looking for an affordable HDV. I frequently shoot 24f and have heard there might be compatibility issues for playback. Anyone have any suggestions/input?
Thanks,
Chris

Did I answer this same question in another forum...because it sounds familiar...
Canon does not make an HDV deck, so you are stuck using the camera. All the HDV formats are exclusive...A tape shot with the Sony, JVC or Canon HDV cameras will not play on any of the other companies cameras or decks.
There is no standardization for HDV...but then again there is no standardization for HD either...
Shane

Unable to Intialize HDV deck - can anyone pls help me with this FCE Issue?

I have recently moved from a MacBook Pro (circa 2 yrs old) to a new MacBook Pro with the NEW firewire 800 port. I have bought a new firewire cable and my camera does not want to be capture from my Sony A1E.
I have a MacBook Pro 2.8ghz running on OS X 10.6.2 and have all the updates installed for FCE.
Every time i try to capture the message comes up "Unable to Intialize HDV deck. Please make sure a deck is connected and try again".
The System is set up to receive the correct frame rate footage and type of footage (which is: HDV-Apple Intermediate Codec 1080i50. Formats: All formats). I am running on PAL, so 25fps.
Is there any advice / direction that you could give me at all as I am struggling!
Any help support would be appreciated!
Thanks, Martin

Hi,
Would you confirm that you are using a 9-pin to 4-pin FW cable to connect to your camcorder and that your camcorder is the only FW device connected to your Mac.
When you start up FCE with the camera connected to your Mac and already powered on in VTR mode, does FCE 'see' the camera, or do you get a warning message that FCE is "Unable to locate the following external devices ..." ?

Unable to initialize hdv deck problem

Hi all,
I'm having the 'unable to initialize hdv deck' problem. I am trying to capture HD footage from a Sony HVR-A1E camera. iLink and down conversion are off (like they should be) and I have just captured a HD tape before the problem started.
I don't understand how I could capture HD footage just fine and then without touching any settings (just trying to start capture again) I suddenly get the error message, "Unable to initialize HDV deck. Please make sure a deck is connected and try again."
Any ideas?

Definitely. Shot on HDV, definite difference between the clips I've captured so far (HD capture that worked fine before this is high quality sharp image, where as when capturing in SD, image quality is poor and smaller).
Everything has been filmed on the same camera with no setting changes between shots. Like I said before, I have already been able to capture today in HD just fine, but for some unknown reason (which I don't think is the prefs.) capture will not work. I can 'trick' FCE into HD capture but it gets stuck on cueing tape (even though video is playing fine on camera).

How do I find out if my iphone is a 3G or 3GS? I bought it used. I'm looking to buy ad install a new battery.

How do I find out if my iphone is a 3G or 3GS? I bought it used. I'm looking to buy and install a new battery. I hve seen batteries and the tool kits for sale on ebay. I replaced the motherboard in my MacBook Pro 17" so the iphone battery is not very daunting. I just ned to make sure I buy the right one.

Have a look at this article:
http://support.apple.com/kb/HT3939

Looking to Buy a New All-In-One Printer

I am looking to buy a new all-in-one Printer.
I have been using the Epson RX620 for a little over a year and have had great print results. Unfortunately I get a warning message yesterday that the printer needs servicing and nothing will work. After getting much less than desirable results from their Customer Support I am moving away from Epson, after three different Epson printers.
I have heard many good things about Canon printers. We will be printing bunches and bunches of photos(two small daughters + graphic artist wife = many, many photos). I am presently looking at the Canon MP600. Any goods or bads about said printer?
We do want a printer that can use cheap cartridges so HP is out of the question. Any other recommendations is appreciated.
Thanks in advance for your replies.
Nick

The only thing that ****** me off about Epson is that they shut down their toll free phone tech support!
I had to rely on their email support to set up my new Epson printer (CD/DVD loading tray) which wasn't so bad as it was very detailed & hands on. I just couldn't understand their manual. I was having one of my "senior moment" days.
Those Canon printers are handsome! I almost ended up getting one. But, the Epson printers won because they are the only ones who can print directly on CD/DVDs & all the software is included.

I am looking at buying a MacBook Air over the Pro mainly for the 12 hour battery. Just wondering if battery is compromised by upgrading to 8mb and upgrading to I7 Intel dual core. I am not very tech savvy so apologies if dumb question

I am looking at buying a MacBook Air over the Pro mainly for the 12 hour battery. Just wondering if battery is compromised by upgrading to 8mb and upgrading to I7 Intel dual core. I am not very tech savvy so apologies if dumb question

If both computers were configured identically, then they would both lose the same amount of battery life with respect to the same starting configuration - comparing apple to apples. I don't know how much the added RAM, etc. would reduce battery life, but it would be less for both models.
Battery life is a tricky subject because most mfgr.s like to suggest as long a life as possible, but often do so under a set of conditions that are not common to most users. Apple is no different. Their computers do have good battery life, however. But not likely as long as what is in the ads for the typical user.

Hello, I am looking to buy your publicaitons as in Adobe Illustrator Cs6 Classroom In A Book by Kordes Adobe Creative Team in all the formats, photoshop, inDesgn etc do you have a blunk price on there so where I can order them ?

Yeah I am looking to buy the book
Adobe Illustrator Cs6 Classroom In A Book
by Kordes Adobe Creative Team
and all others....is there a blunk price I can get them somewhere.

This is a Photoshop user forum site users here do not work for Adobe though some Adobe employees do drop in from time to time. Try Adobe.com search or call Adobe 1 (800) 833-6687 Adobe Systems, Customer service

Looking to buy Time Capsule. What is the best way to connect printer to network?

Looking to buy a Time Capsule. I have a wifi canon printer currently. If I connect the printer to the Time Capsule via wifi will it be shared the same as if I connected the printer via USB? I would like anyone who connects to my network be able to use the printer. I want to know the best way to configure it so that is easy to connect. Thanks
Dustin

If I connect the printer to the Time Capsule via wifi will it be shared the same as if I connected the printer via USB?
Yes, assuming that the printer is located where it can receive a strong wireless signal.
I would like anyone who connects to my network be able to use the printer. I want to know the best way to configure it so that is easy to connect
Follow the steps provided by Canon to install the printer and have it "join" the wireless network that will be provided by the Time Capsule.

Cannot preview or monitor on hdv deck

Hi,
I have a Sony HVR-10P HDV deck connected to FCP 5.1.2 with a dual 2GHz G5, 2.5GB Ram. I've just upgraded with the intention of running HDV but I can't seem to get a running signal to this HDV deck. When I select the the 'video playback' the HDV output settings are greyed out. What does this mean?
I have selected HDV editing from 'Easy Setups'. I've re-connected firewire and rebooted FCP. I can output a still frame through Firewire DV, but still, this doesn't run as video, it only presents a still frame when paused.
Is this something to do with the deck? I've also tried all the HDV Firewire Basic and 25fps HDV for PAL options.
Any help would be greatly appreciated,
thanks,
Sam
G5 Dual 2Ghz G4 Powerbook 867Mhz Mac OS X (10.4.8) 2.5GB RAM 128MB vram

you can not preview/monitor HDV live from the timeline via FW
if you want to edit with HDV and view the timeline to an external monitor, as you might with DV, then you must use third party equipment such as the Matrox MXO box, or a suitable HD card from AJA or Decklink

I'm looking to buy a Mac mini, has the tv connection issue been totally fixed yet?

As above. I'm looking to buy a Mac mini 2.6 i7 fusion drive and want to connect it to my Panasonic viera HDTV. (27") read a lot about People having issues connecting to a HDTV. My tv only has 2 hdmi ports, no dvi VGA etc. if it hasn't been fixed I'm going to have to purchase a Smaller monitor due to lack of space!
Thanks in advance.

That has helped/worked for about 96% f the people.

Looking to buy an HDV deck

Similar Messages

Maybe you are looking for