Looking to step up - need advice.

I am a photographer who has been getting by with a Mac Mini, iMac and Last years macbook pro.
The mini is my main machine. It is the 2009 version and I have dual monitors connected.
It's response in PSCS 5 could be faster.
Is a used mac like this for $1,000 faster or slower than my mac mini? Specs: 4 x 2.66 GHz Intel Xeon Processors, 3 GB Ram, 320 GB Hard Drive, Dual SuperDrives (DVD Burners), Bluetooth and ATI Radeon X1900 512 MB Video Card.
If so, what about a iMac vs my Mini vs a low end current Mac Pro? Is it well worth the cost?
Thanks for the advice.

I am not sure where you see $1000 system, but 2009 Mac Pro is $2100 and has 4 CORES, not processors, and would do nicely.
Then add 3 x 4GB RAM probably for next step.
The only $1000 would be 2006 Mac Pro, and no I would pass on it. Besides being 4 yrs old, unless that is your best/only option.
As for iMac, they do have Core i5/i7 4-core but easier to outgrow than a Mac Pro would be. And if you do work with CS5, RAM is really important as well as a couple internal hard drives.
http://www.barefeats.com/wst10c2.html
http://store.apple.com/us/browse/home/specialdeals/mac/mac_pro
There is a 'recall' on some of the X1900s, they are also dated; can be upgraded to ATI 5770 ($249).
Check out this article, then check the index and topics, choosing a Mac, optimizing for photography, and how to guides.
http://macperformanceguide.com/Reviews-MacProWestmere-Estimates.html

Similar Messages

I have a macbook with Tiger. What are the steps I need to take to upgrade to Lion and the cloud? I have the Snow leopard disk just received from Apple.

What are the steps I need to take to upgrade my Macbook with Tiger to Lion and the cloud? I have the install disk for Snow Leopard.

Hi Carol, good/sound advice by Ziatron so far.
We need more info about your Mac to see if it will even be capable,
So we know more about it...
At the Apple Icon at top left>About this Mac, then click on More Info, then click on Hardware> and report this upto but not including the Serial#...
Hardware Overview:
Model Name: iMac
Model Identifier: iMac7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 6 GB
Bus Speed: 800 MHz
Boot ROM Version: IM71.007A.B03
SMC Version (system): 1.21f4
You'll need to buy SL/10.6 first & get it to 10.6.8, then get Lion... if you can run it.
Or if you can erase your disk...
http://store.apple.com/us/product/MD256
Snow Leopard/10.6.x Requirements...
General requirements
   * Mac computer with an Intel processor
    * 1GB of memory (I say 2GB at least)
    * 5GB of available disk space (I say 30GB at least)
    * DVD drive for installation
    * Some features require a compatible Internet service provider; fees may apply.
    * Some features require Apple’s MobileMe service; fees and terms apply.
Which apps work with Mac OS X 10.6?...
http://snowleopard.wikidot.com/
It looks like they do still have it:
http://store.apple.com/us/product/MC573Z/A?fnode=MTY1NDAzOA
If it's a core Duo & not a Core2Duo, then it'll only run in 32 bit mode.
Snow Leopard/10.6.x Requirements...
Lion/101.7 System requirements
    •    x86-64 processor (Macs with an Intel Core 2 Duo, Intel Core i3, Intel Core i5, Intel Core i7, or Xeon processor.)
    •    At least 2GB of memory, (I say 4GB)
    •    Latest version of Mac OS X Snow Leopard (10.6.8), with the Mac App Store installed
    •    At least 4GB of disk space for downloading, (I say 40GB at least)
Like Snow Leopard, Lion does not support PowerPC-based Macs (e.g., Power Macs, PowerBooks, iBooks, iMacs (G3-G5), eMacs).
Lion also does not support 32-bit Intel Core Duo or Core Solo based Macs. Rosetta is no longer available in Lion, which means Lion no longer supports PowerPC applications.
It looks like Apple will have Lion available on USB drives for $69...
http://store.apple.com/us/product/MD256

Need advice on video software.

Need advice on video software.
I currently use adobe elements 3 and have done so for a few years now with no problems. my os is XP and my system is a couple of years old, but we do have a brand new win7 machine in the house.
I am currently look at Cyberlink PowerDirector 8 Ultra OR Adobe Premiere Elements 8. Reviews for both softwares seem very good BUT, when I dig deeper into user reviews instead of editor reviews do I find problems.
Major problems with program crashing all over the place, at start up etc, and it is still not getting along with any win7 machine? Major problems with drivers. Honestly, I do not want to have to jump through dozens of hoops to get any software to run. After I pay for it, it should run, period.
Has anyone else here used both softwares and can you give an honest opinion of each?
I am also asking these same questions on the cyberlink site.
I would like to upgrade my video software to take advantage of the new features that are coming out but I really don't want a big headache trying to run one or the other. To be fair, when I bought adobe elements 3 I had also bought pinnacle, which has gathered dust since my first week with it, which is why elements was purchased. That was money wasted and I do not wish to repeat this. I would like to go with Premiere Elements 8 but remain very unsure.

If your newer machine is Win7 64-bit, it might be worth waiting for SP-1 to be issued, and then hope that 64-bit drivers are fully included. The 64-bit drivers now seem t be an issue at this point, and that will affect any NLE program.
Also, and regardless of which particular program you choose, optimizing your computer, the OS, the hardware, and the resources management, will go a very long way to insuring success. Few programs can tax a computer, as an NLE can - any NLE. Video and Audio editing will stress your system, like almost nothing else can, except for heavy-duty CAD, or 3D work, though those are usually done only on specialized, optimized computers, designed just for those applications.
Not the specific advice that you seek, but it's the best that I can do.
Good luck,
Hunt

JMS to Synchronous Web Service Scenario (Need Advice to use BPM or Not)

Hi Experts,
We have a scenario where we fetch data from JMS Sender and Send it to MDM Webservices.
We want to have the files processed in such a way that until we get a response from webservice back that it was sucessful ,then only we need to process the next file.
We would need advice as can we use BPM for this.
We are thinking of having BPM like this:
RecieveStep(Asyn)-SynchronousSend Step(with wait)-Stop
The problem with this is when processing huge files the processing time of the Queue is taking very long and sometimes we are getting SYSFAIL.
Please would anyone advice as how can we approach this scenario either using BPM or without.
Also Can we use multiple queues or multpile instances concept for this scenario.
Please Advice.
Thanks in Advance
Regards
J

Hi Prateek,
Thank you very much for your quick reply.
The response from Webservice does not need to be sent anywhere.
We just want that after recieving the response back from webservice(SOAP) then only we need to process the next file.
Can we control something from Sender JMS adapter side as well as it is picking up all the files and all files wait at BPE until each one gets processed.
Is this possible without BPM or with BPM.
Please advice as what wud be possible steps inorder to achive it through BPM or Without BPM.
Thanks and Regards,
J

Ready to take it one higher ...need advice on best way to get more audio in

Nearly ready to upgrade to LP7...need advice on more gear.
Longtime Logic user, my old rig running with an Audiowerk 8 card (dont laugh too hard please, its worked great for years! ).
Now, after purchasing a MBP and LE7 ... how best to upgrade even further, to be able to record say 4-8 tracks (live instrument) at a time, into the optical or Firewire ports. I have an external 750Gb FW drive.
Also have a Mackie 16 chnl mixer and hoping to find a way to send the Master stereo pair (or maybe even track inserts) from the Mackie to the optical or FW input of my MBP. But how to do this ? Im guessing there's a box or gizmo somewhere that would be perfect.
Unfortunately, all of the boxes and gizmos Ive looked at so far seem to duplicate functions I already have, esp mic preamps (dont need any more of those !). I prefer 19" rackmount devices as they work well with portability, and fit into my SKB rig easily.
TIA

Also have a Mackie 16 chnl mixer and hoping to find a way to send the
Master stereo pair (or maybe even track inserts) from the Mackie to the
optical or FW input of my MBP. But how to do this ? Im guessing there's
a box or gizmo somewhere that would be perfect.
if you really want to use the pre's on your mackie, and it has multiple bus/aux outputs which I presume it does, then you can easily set up a device such as the 828 to take all your input channels from the mackie, and then to run a bunch of return pairs back out to it.
depending on your budget there are prob a few others for you to look at. RME and metric halo always get rave reviews from users, but are pricier. also the focusrite sapphire might be worth a look, as well as the apogee ensemble.
also I just noticed you are using logic express, not pro. so there may be some limitations on the number of simultaneous inputs and outputs that I'm unaware of.

New user of G4 - need advice on selection of printer, DV and digital camera

I am a recent convert to mac and need advice from experts on the following:
I plan to use my G4 MDD primarily for home computing, experimenting with digital photography, create DVDs and explore multimedia primarily as a hobby. Please advice me on selection of a decent digital camera and or a DV camera. I am not sure if I have a decent DV camera - whether this will be good enough for still photos as well. My G4 has firewire ports.
Also I am interested in buying a printer that I can use with my mac as well as connect to a two other windows systems. My printing needs are primarily documents and maybe photos.. I think that going in for a laser printer makes sense in terms of reliability .
I am not looking for the highend equipment - willing to spend upto 750 $ on all items. Thanks in advance.

raja,
welcome to discussions.
Digital Camera, DV camera and colour Laser Printer all for $750 ??
I'm afraid you'll have to go for an inkjet printer if you want colour photos. Expensive doesn't even begin to describe Colour Laser Printers. HP make good printers, but tend to be a bit more expensive to run, Epson make excellent photo printers, are are a bit more economical to run, take a look at the iP4000 and iP5000. I still use my old HP DeskJet 1200 (does A3), and a DeskJet 970Cxi (everyday), both use the same cartidges. These are about 7 years old, there are modern versions retailing now at about half of what I paid for these then(always the case).
Digital cameras can be decided by what purpose you intend to use them for. I have an 18 month old Nikon D100 digital SLR. 6M pixel (which was a lot then) but that might not matter, it takes Nikon lenses (and other manufacturer lenses to the same spec), so I can shoot with a 300mm, 400mm, 600mm lens. Nikon has a D50 out now, a cheaper, newer version of my camera. I can print A3 photo real from 6M pixels and with the right lens I don't need to crop my pictures too much. If you want to print photo real A4 (and that's a LOT of ink) a 3-4M pixel camera would be fine. Most cameras now are 5-8 M pixel, this is because the pictures they take have to be cropped drastically because they have an inadequate lens. On top of that my Nikon takes really great pictures, better than any of my other digi cameras (but not as good as my ancient Olympus 35mm muji-zoom compact with 200 film).
So if you're going to take a lot of close ups in well lit areas, product shots, interior shots with flash, ie. "snaps" rather than photography, any cheap digi camera will do. Good points are
- USB / Firewire connectivity,
- non-proprietry battery technology, ie. it uses 4 x recharable AAs instead of a battery that only fits that camera, and it comes with a AA recharger.
- non-proprietry storage technology, ie. it uses Compact Flash or some other that is used by a large portion of cameras, rather than just be that manufacturer.
- digital zoom is worthless.
If you're doing outdoor photography, wildlife, landscapes, etc, you may want something with a changeable lens and SLR technology, a digital SLR. Not all digital SLR cameras have changeable lenses. Same good points as above, but be prepared to sacrifice one of the points for a good camera. Heavy cameras are easier to hold steady with a big lens, so try for a metal case (it'll be coated in plastic anyway).
For outdoors the most important thing is the amount of light entering the camera (indoors you can control the lighting with flash / fitted lighting), digital SLRs can have enormous lenses (my 28mm hyperzoom lens has a 72mm diameter), compare this to a compact digital camera with a 12mm diameter lens, I take 36x the light of a compact. And it shows in the picture quality.
I'm a complete duffer with DV cameras so I won't lead you astray with this, but be aware some do offer the option to take digital pictures. Indeed some digital cameras can take low quality short movies.
Let us know if you have any more questions.

Need advice on a proof printer

Hello. So glad I found this site!
I'm currently a print graphic designer and starting a home based business integrating my print design knowledge with newly acquired web design skills to offer a complete package.
I am working on an HP computer, as I cannot afford the Mac I want now. I have all of the Adobe software for PC already, but need advice for a printer.
The machines I work on now are like $18k - 25k color lasers, and clearly that is not in my budget. I'm a little lost as to what to look for in a printer that can handle color proofs of my artwork. I create a lot of raster images in PS, but logo design is one of my focuses, so vector output is essential. I almost always create outlines of fonts for the final press ready file, so I'm not so worried about fonts, but color matching is important.
I've been reading about Postscript and PCL, but am still very confused. I'm also a little confused as to what a rip does or if I need one. We use one at my shop, and I know how to use it, but it lives on the server and was explained that it was only necessary for networking the printers.
I am planning to outsource all of my final printing, but I need a printer for proofing. I've been looking at inkjets for affordability reasons, but now I'm not sure if I need a color laser.
Help!!

Dear VectorGirly, I currently have an OKI Postscript c9800 printer. I use postscript printers because I calibrate and use color profiles to get the closest colour match to the outsourced commercial print that I can. I know this is more than you budgeted for, but it really depends what you end up focusing on. (ie web or print). I focus more on print, hence my printer has to proof postscript correctly for me. I am PC based but my files print to both PC and Mac platforms.
Regarding logos and colors ... firstly, my monitor is calibrated with a Pantone Huey. I use matching color profiles in all my design programs: Indesign, Illustrator, Photoshop. My print PDFs include the color profiles. When I email or post proofs of logos or corporate stationery to clients I make sure they understand that colors will look different on various monitors because they are not calibrated for print and are RGB or color prism based rather than CMYK for print. Even if you choose a Pantone color, unless everything is calibrated and with color profiles, it's unlikely that you will get the same color on your screen, let alone on the client's screen. And if the client is wanting a color that looks good on their screen, it's even harder. I always recommend they look at the proof colours on various screens including friends so they can understand how it changes according to monitors.
Regarding PCL and Postscript: When I purchased my OKI (and my former Fuji Xerox pscript), I sent an existing print PDF (that had gone to commercial print previously) to the head office and asked them to do printouts of all the printers I was interested in. All the printers based as PCL were very inaccurate color. The two with postscript took my PDF and printed correctly and were very close to the final printed output. As I am pedantic on colour (colour in Australian spelling), I had to choose the high end postcript laser. Having said that, I am also very interested in the Fuji Xerox Phaser 8500 which is postscript and solid ink (great for the environment and people with allergies and low running costs - much better than laser) - but I need the A3 and banner printing option and they haven't made one for that size yet. I am hoping the new release may offer a bigger size paper. I have a very high allergy level and have to have the window open and a mask on when changing toners and printing, hence my interest in the solid ink for the future.
I always download my fonts through the print PDF to the printer - I never use printer inbuilt fonts. This is so I know that WYSIWYG (what you see is what you get) when I print commercially as they also download/use the embedded PDF fonts.
Also, somewhere down the line you may find yourself forced to choose between focusing on web and print.
I recommend you choose what you love best.

Firmware v2.1 bricks my camera - Need advice

I need advice. I bought the FS7 a month ago and it came with Firmware 2.0. I have been getting used to the camera and I think it's a great machine, still has some bugs, but manageable. The huge issue I have found it that I cannot upgrade to V2.1 without the camera stopping to function. I do the upgrade procedure as stated by Sony http://bit.ly/1E4o32D Using a 32 GB Class 10 Sony SD card. The .md5 is correct. No lenses or adapters installed, no battery, no cards, not even the grip remote. I have tried several times, even after an ALL RESET. The procedure takes the normal amount of time in step one. When step one gets to 100% it restarts the camera and starts step 2. When step 2 ends, ussually after 9m45s, it pops a screen saying "Software Upgraded" with only one option to click on "Done". Then, I cannot push the "Done" because all buttons in the camere have ceased to respond. Nothing electronic in the body works. The on/off button does not turn off the camera, so I ended up taking the power cord out. After that the camera starts out normally but the buttons will not work. I finnally found out (I was thinking the camera was a brick by this point) that I could use the remote grip buttons. So I have ended up installing V2.0... five times I have tried it. It does not work. Any help please?

Hi Daniel, Thank you for the comments about my training video, but I'm afraid I don't have an answer about your firmware update problem if it's not the HOLD button. To be honest, I have not even bothered to update to 2.1 myself yet. Normally I try to keep my firmware updated, but in this case, I'm too busy and I just don't care enough to bother with it. None of the "improvements" interest me and I'm happy with the camera is running right now. Yes, I am guilty of not following my own advice about keeping the firmware up to date. I guess you can either reach out to Sony or just keep using 2.0 until another update is released. I know what I would do, but I don't want to offer any advice one way or the other. The scene files that can be downloaded from my website were created with v1.1 and I have not seen any reason to update them. They sitll work fine for me and nobody has reported any issues. Good luck.

I need advice: photo programm

Hello,
I need advice: which photo-software is a good option, when I don't want to pay the price of Photoshop?
iMac 10.6
Thank you!
Sonja
Nederland

If iPhoto doesn't do what you need you could have a look at Aperture (available at the Mac App Store, but have a look here for a free trial: http://www.apple.com/aperture/trial/
Pixelmator is the one I use - great value for the money and does everything I used to need to do in Photoshop. Have a look here: http://www.pixelmator.com/
If you buy it from the Mac App Store Pixelmator comes with a free upgrade to version 2 (rumoured to be in the next couple of weeks, according to the developers blog).
Usual caveat: I don't intend to sound like a commercial, just a happy user with no connections to Pixelmator.

HELP: New to Mavericks. Need advice on setting up secure user accounts

Hi,
I need advice on how to best set up user accounts on Mavericks.
I must set up an Administrative account...Any suggestion for best settings here to protect against targeted malicious exploits?
I would also like to set up two user accounts for everyday work with applications and Internet browsing done in such a way that the machine would be protected from malicious attacks but with a minimum of inconvience for the users ( myself and my wife ).
Thanks

Hi hassiman, any exploits will come in the form of users downloading suspect pieces of software like browser add-ons and extensions, device drivers and non-trusted apps.
Make sure that you do not use the admin account for any day to day use
Create two normal user accounts, one for each of you and use them day to day
When using the admin account to set up your system, pay very careful attention to the System Preferences > Privacy & Security area. There are various things to set up properly here:
There are three settings for how people can download software, 1) From Mac App Store only, 2) From App Store and registered developers and 3) from anyone. It defaults to 2) but check it and if you feel uncomfortable with that, set it to 1). This might prevent you from downloading and installing software you think you might need; but think carefully about wether you really need it and therefore wether you should temporarily allow it via a lower setting.
For the firewall, if you dont have a firewalled internet gateway device (a wireless router or similar), make sure the firewall is turned on. Most internet connection equipment does have such a firewall; make sure it is blocking any incoming connections by using its admin tool (usually a web browser interface). Consult its documentation for details.
Whenever OS X asks for a password to complete a task of any kind, look carefully at what is making it ask and if you aren't sure, don't go through with it; it is usually wanting the admin account name and ppassword to complete some kind of system modification (install, config etc.).
Make sure that you are both aware of the danger of installing any software that wants to add itself to your system or web browser. Things like custom search bars, extensions etc. If you are viewing a web page and it says you need "x" to see it or use it properly, make sure you really need to use that web site; otherwise don't do it.
It really all comes down to common sense; the worst security breaches and damage come from users who don't know what to do, but they still click "OK" when they should be clicking "cancel" or "close". Make sure you and your wife are fully aware that responsibility lies with yourselves. It is better to take a minute to decide wether to install something (even if it's 20 times a week) than spend days fixing a compromised system.

Need advice for installing flex application in touch screen Kiosks

Hello,
We have a requirement in one of our project to create touch screen interfaces and I am intending to user Adobe Flex for the development and run them in Adobe Air because, definitely it saves development time and great look and feel.
However, I need advice on how to connect the application to a touch screen events like we do on Keyborad and mouse events like, click() or onFocus etc.
Please advice.
Best Regards,
Jai Kishan Shah

Bar Code Scanners are no different than keyboards in my experience. It just sends the text to whatever application is open. Integrating it with Flex requires no effort. You just have to be sure that Flex is the current application and the field you want to put the data in is given focus.
In a point of sale application with very specific use case and limited interface, it is easy to force the app to give focus to the input field that needs to accept your input.
Credit card swipers work the same way.
I don't know about a weighing scale, but I bet it is very similar. If not, you may want to use Java for scale integration and then use Merapi to integrate with the Java applet.

Need advice on Career in SAP after completing 9 yrs in IT mainly in Telecommunication Domain with BMC Remedy Tool knowledge

Need advice on Career in SAP after completing 9 yrs in IT mainly in Telecommunication Domain with BMC Remedy Tool knowledge.
Which Module of SAP I can learn and get into as I have Tool based knowledge in BMC Remedy and fair knowledge in SQL, as I come from non-IT background. What are career prospect after completing any SAP module now will my previous experience will be taken into account?

Prashant,
One of the reasons nobody has replied to you yet is that, this is a question with so little information provided.
- There is no mention of your education background.
- Your work background is very vague.What exactly did you do in Telecommunication Domain?
- What exactly did you do in BMC Remedy? Where you just an end-user or did you do any background support work?
- What exactly did you do in SQL? Did you work on it or did you just attend training?
- Why do you want to jump into SAP? And what precisely you want to jump into in SAP?
- What are your interests? Technical or Non-technical?
- What's your career objective? Where do you want to be 5 years from now?
Without providing these information how can anyone help you? Picking a module and going with it makes no sense. What if you spend an insane amount of time and money learning a module in SAP (based on some random suggestions given here) and realize that this is not what you were looking for, or there is little scope for that module in the market? What then?
It's your career that you are planning. It definitely deserves more thought-process and planning to go into.
pk

Step-by-Step Help Needed for Deploying Some Adobe Software

We are a K-12 educational institution. I am currently working at setting up a computer lab with about 16 MacMini computers.
I'm VERY new to the realm of servers, deployment, using terminal, etc.
I've done lots of research to make it to where I am, but just can't wrap my head around what needs done next with the Adobe products.
I am using Server OSX (v3) and DeployStudio (v 1.6.3) to try and manage the computers.
Both my server and clients are running Mavericks 10.9.
I deployed my core images successfully and would like to now send Adobe products only the computers I choose since I have limited licenses.
We have volume licenses of Adobe InDesign CS6 and Photoshop Elements 12 that we would like to deploy.
I have been referencing the following sites, but just can't seem to wrap my head around the EXACT steps that need to be taken.
http://blogs.adobe.com/oobe/2010/10/adobe-provisioning-toolkit-enterprise-edition.html
http://helpx.adobe.com/creative-cloud/packager/provisioning-toolkit-enterprise.html
http://helpx.adobe.com/photoshop-elements/kb/silent-install-instructions-photoshop-element s2.html
http://forums.adobe.com/message/5781663
For Adobe InDesign CS6 - I've done the following:
Created an "Installation Package" using Adobe Application Manager Enterprise Edition (AAMEE v6.2.112.0) using the following instructions.
http://wwwimages.adobe.com/www.adobe.com/content/dam/Adobe/en/devnet/creativesuite/pdfs/Ad obeApplicationManagerEnterpriseEditionDeploymentGuide_v_3_1.pdf
If I log into the client computer, put the package ON the client computer, and run it...it takes me through the install and works wonderfully.It's not automated like I wanted/thought I set it up to do. I have to click through the steps of the installer.
If I try to deploy it using the "Package install" Workflow in DeployStudio...it loads it during the workflow, then skips through it, acts like it installed it, but it isn't actually installed.Is there a setting that I need to possibly change somewhere?
For Adobe Photoshop Elements 12 - I'm a bit lost and mostly just have questions:
I know that I can't use AAMEE and need to use APTEE (Adobe Provisioning Toolkit Enterprise Edition).
How do I deploy the software? Create my own Package using PackageMaker?
Which computer do I run APTEE on? All the instructions I can find just say, "do this" - but don't specify where.
Do I have to open terminal and run the commands on each client computer AFTER installing PE12?
OR
Do I run the commands BEFORE deployment on my package stored on my server that is ready for deployment?
It really comes down to me just not 100% understanding how APTEE works.
I hope that pertrays my dilemma. I've tried to explain best I can. If you have any questions - let me know!
Thanks in advance for any insight you can give!

We are a K-12 educational institution. I am currently working at setting up a computer lab with about 16 MacMini computers.
I'm VERY new to the realm of servers, deployment, using terminal, etc.
I've done lots of research to make it to where I am, but just can't wrap my head around what needs done next with the Adobe products.
I am using Server OSX (v3) and DeployStudio (v 1.6.3) to try and manage the computers.
Both my server and clients are running Mavericks 10.9.
I deployed my core images successfully and would like to now send Adobe products only the computers I choose since I have limited licenses.
We have volume licenses of Adobe InDesign CS6 and Photoshop Elements 12 that we would like to deploy.
I have been referencing the following sites, but just can't seem to wrap my head around the EXACT steps that need to be taken.
http://blogs.adobe.com/oobe/2010/10/adobe-provisioning-toolkit-enterprise-edition.html
http://helpx.adobe.com/creative-cloud/packager/provisioning-toolkit-enterprise.html
http://helpx.adobe.com/photoshop-elements/kb/silent-install-instructions-photoshop-element s2.html
http://forums.adobe.com/message/5781663
For Adobe InDesign CS6 - I've done the following:
Created an "Installation Package" using Adobe Application Manager Enterprise Edition (AAMEE v6.2.112.0) using the following instructions.
http://wwwimages.adobe.com/www.adobe.com/content/dam/Adobe/en/devnet/creativesuite/pdfs/Ad obeApplicationManagerEnterpriseEditionDeploymentGuide_v_3_1.pdf
If I log into the client computer, put the package ON the client computer, and run it...it takes me through the install and works wonderfully.It's not automated like I wanted/thought I set it up to do. I have to click through the steps of the installer.
If I try to deploy it using the "Package install" Workflow in DeployStudio...it loads it during the workflow, then skips through it, acts like it installed it, but it isn't actually installed.Is there a setting that I need to possibly change somewhere?
For Adobe Photoshop Elements 12 - I'm a bit lost and mostly just have questions:
I know that I can't use AAMEE and need to use APTEE (Adobe Provisioning Toolkit Enterprise Edition).
How do I deploy the software? Create my own Package using PackageMaker?
Which computer do I run APTEE on? All the instructions I can find just say, "do this" - but don't specify where.
Do I have to open terminal and run the commands on each client computer AFTER installing PE12?
OR
Do I run the commands BEFORE deployment on my package stored on my server that is ready for deployment?
It really comes down to me just not 100% understanding how APTEE works.
I hope that pertrays my dilemma. I've tried to explain best I can. If you have any questions - let me know!
Thanks in advance for any insight you can give!

Need advice about certification: do J2SE 1.4 or wait for 1.5 to go out?

I need advice here! I am studing for Java Programmer certification (310-035) and I know now that the certification does not have any expiration date, instead it's version based. So, if I get now a J2SE 1.4 certification, soon it will be outdated... I guess!
Does anyone know or have any ideia of WHEN java 1.5 sdk will be avaliable, and anyone can tell me how long it will take for a new 1.5 programmer certification be avaliable for general public?

Do both. 1.5 is far enough away that you do not want to wait for it.
And besides, 1.5 has enough new stuff in it that you'll want to recertify anyway.

Need advice on on a Mac Pro 1,1 Media Center

I currently have a 2009 Mac Mini running as my home media center, but I recently came by a FREE Mac Pro 1,1 and have decided to repurpose it as my media center so I can migrate my Mac Mini to my bedroom TV where it will live an easy life doing nothing but run Plex Home Theater, Netflix, and EyeTV. This machine falling into my lap was also quite timely because my 4-bay Drobo is running low on available expansion and another Drobo isn't in the budget at the moment.
This vintage mac pro is running Lion 10.7.5, has 1 old and crusty 500GB hardrive, dual x5160 processors, 4GB RAM (one stick i'm pretty sure is toast judging by the red light and the kernel panics), and the standard NVIDIA GeForce 7300 GT 256MB graphics card. It will be used primarily for the following: network storage for iphoto and itunes libraries, streaming video, Plex Media Server & Plex Home Theater, and Handbrake encoding. I also have a goal of safety of data for my movies, photos and music as this machine will supplement my current Drobo storage.
My plans are for a 128GB SSD boot drive installed in one of the PCIe slots and then to load up all 4 of the 3.5" drive bays with WD Green hard drives. I have also ordered 4GB of replacement RAM, so upon removal of the faulty unit I will have 7GB.
Here is where I need advice because I am not very familiar with RAID and the differences between hardware or software raid. Am I better off getting four drives of the same size and setting them up as RAID 5 (I think) using Apple's RAID utility or should I throw in three 1TB drives and then install a fourth 3TB or 4TB drive as a Time Machine backup for the other three?
Should I upgrade the OSX to the technically unsupported latest version? Or is it not worth the trouble for this application?
Also, is there any benefit to upgrading the graphics card to the ATI Radeon 5770? Would this yield an improved image quality? I am outputting to a Denon AV Reciever and subsequently to a 100" projection screen, if that makes a difference. I also noticed the 5770 has an HDMI port, wich would be nice, but not necessary since I can use a DVI converter and woud still need to use the optical audio out anyway.
Much obliged for any input

My plans are for a 128GB SSD boot drive installed in one of the PCIe slots and then to load up all 4 of the 3.5" drive bays with WD Green hard drives. I have also ordered 4GB of replacement RAM, so upon removal of the faulty unit I will have 7GB.
PCIe cards that use or support SSD are not bootable until you get to 2008 (and that is limited too).
Green are not suited for any form of array unless say NAS and WD RED. Better option would be 3 x 2TB WD Blacks in a mirror, and too many people only use two drives, well 3 is much easier safer and works better. Might want to invest in www.SoftRAID.com product even.
Best price and quality, got my 1,1 with 8 x 2GB (ideal is 4 or 8 DIMMs)
2x2GB FBDIMM DDR2 667MHz @ $25
http://www.amazon.com/BUFFERED-PC2-5300-FB-DIMM-APPLE-Memory/dp/B002ORUUAC/
With price of 250GB SSD $155 I'd go with that or stick with $89 for 128GB .

Looking to step up - need advice.

Similar Messages

Maybe you are looking for