Loosing connection with my xbox360

Hi everyone, I just purchased a wrt160n router and I am wireless with my xbox360. While on xbox live playing an online game "cod4" I can't get through a game most of the time without loosing a connection, with the 54gs router I had there was not an issue. Any help would be appreciated!!

Try few wireless settings on the Router ...
Access setup page of router ....
Click on Advanced Wireless
settings>>Change the Beacon Interval to 75 >>Change the Fragmentation
Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" ....
See if it shows stable connection with X-BOX ....

Similar Messages

Why my IPAD2 sometimes loose connection with my router and I need to enter again the WPA password?

Why when my IPAD2 loose connection with the router sometime I need to enter again WPA2 password?

same problem here.
MBA (latest os), even my ip5 (latest ios) & ipm (also latest ios) looses the connecntion.
Ive tried to figure out what causes the problem - neither my xbox360 nor (and i guessed they will be the problem) the pcs here...
the connecntion runs well.. switching also (MBA-IP5-IPM).. but not for longer than an hour.. or even minutes. When the connection looses a high-frequency noise is followed by silence. A restart fix that problem and all devices streaming well... but not for long...
any suggestions?

I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows 8?

I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows

Hi, stig2013.
I would recommend the steps in the article below. See the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
If you are receiving an error message, find the exact error number that you recieved in the article below and process the steps.
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if you manually disconnect the device during the restore process. You can resolve this issue by using USB troubleshooting, using a different Dock Connector or Lightning Connector to USB cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
Cheers,
Jason H.

Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen. Full Wifi signal on both devices

Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen. Full Wifi signal on both devices so can't think what could be causing it to happen. Any suggestions please?

Sorry, I updated another thread I was a part of but didn't update my own thread.....ughhh!
I updated all of my ATV 2's and 3's to the latest firmware when it was released and have been problem free since. I do believe the major issue of not being able to connect after a period of inactivity has been corrected with the latest ATV firmware.
I can look at my network connection table using "netstat -an" in a CMD window and I do not see the massive number of connections I saw before the update.
Here is a link to the other thread I was referring to above:
https://discussions.apple.com/message/19952545#19952545
Have you applied the latest firmware updates to your ATV 3's?

MacBook looses connection with external monitor

Hey Apple humans!
I have a MacBook Pro (mid 2009) and an external monitor Samsung SyncMaster XL2370 connected via DVI/DisplayPort. Works fine since the mid of 2009 but in the last few days the MacBook looses connection with the monitor and isn't able to get the connection up again. The button "Monitore recognise" (don't know the exact translation of it in english) in preferences doesn't work, even a reboot brings nothing.
I've changed nothing on the setup, only the newest patches for OS X were installed. Any ideas?
Thanks in advance and sorry for my bad english, right now I'm to ****** to concentrate
Message was edited by: FabianFerdinand
Message was edited by: FabianFerdinand

have a Mac Pro with 2 Samsung syncmasters and after updating os x to 10.6.6 computer loose the connection with the monitors. Randomly it seems, might work for a while and suddenly go black.
Have to restart the Mac. I'm sure it's related to the os update. Tried all resets, throwing prefs, emptying
cache but nothing helps.
Jesper

HT1414 Since updating to iso6.0 I have had problems with my email exchange account syncing correctly - I keeps loosing connection with the server.

Since updating to iso6.0 I have had problems with my email exchange account syncing correctly - I keeps loosing connection with the server.

Are you losing the connection to iTunes on the iPad or the computer? You are saying that iTunes is updated. Of course iTunes is updated when you update the iOS software. That's a no brainer.
If you mean that iTunes is updated on the computer, that has absolutely nothing whatsoever to do with downloading and updating apps on the iPad itself so changing the date on the iPad, signing in and out of the stores on the iPad .... Doing any of that on the iPad would have nothing to do with iTunes on your computer.
If .... you have not been able to connect to the iTunes or app stores at all on the iPad - try this ...
Settings>Privacy>Location Services>System Services (swipe to the bottom of the page to find this)>Location Based iAds>Off.
If the downloads are stalled or "waiting" - try these suggestions.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
Make sure that you do not have a stalled download in iTunes - a song or podcast .... if you have a download in there that did not finish, complete that one first. Only one thing can download at a time on the iPad so that could be what is causing the problem.
If you can't connect at all - you can also try rebooting your router. Unplug it from power for about 30 seconds and then plug it in again.

Issues with client looses connection with 6.0.196.0

Hi,
We recently upgraded our Wisms to version 6.0.196.0 and after the upgrade we have seen the clients sometimes looses connectivity and has problems to connect. We use an network with 802.1x and PeapMschapv2 with dynamic WEP.
We have disabled aggresive load-balancing but still see the issues.
Any ideas anyone?
Regards,
Martin

Hi,
Any news for these problems? Did the version 7.x fix these CAPWAP UP/DOWN problems with HREAP APs? It seems that I'm having these same problems now. Local APs seems to be fine, but HREAP APs goes UP/DOWN with versions 6.0.196.0 and 6.0.199.4.
There are three 4404 WLCs, where are different sites' office and warehouse APs connected to. The environment is configured as N + N + 1
like following:
WLC1 is for officeAPs. APs are 1131 and they're configured as H-REAP
WLC2 is for warehouseAPs. APs are 1242 and they're configured as Local
WLC3 is for backup and I used this for testing.
After I updated all the WLCs at summer to version 6.0.196.0, there have been issues where the clients looses randomly WLAN-connections. But the complaints just came from the two largest offices. And these didn't happend immeaditly after the update, but after few months. It can be that the summer holidays was reason for it. After some investigations, I updated the WLC3 for version 6.0.199.4, which just got released at the time, and moved these two largest offices' APs to there. Complaints stopped but after a month the second largest office informed that the clients' disconnections started to raise again and the WLAN-network has become unstable again. First there was just couple of issues but it have been raised as the time goes by.
When I made some more investigation to this site, I noticed that the APs' CAPWAP goes DOWN and UP randomly for a second:
*Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN
*Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Nov 12 07:39:29.759: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Nov 12 07:39:29.811: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 12 07:39:29.812: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Nov 12 07:39:29.849: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 12 07:39:29.850: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 12 07:39:29.889: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Then I investigated some more and noticed that this happens on all of the H-REAP APs and almost in the same time:
*Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's AP (6.0.199.4)
*Nov 12 07:40:17.439: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's other AP (6.0.199.4)
*Nov 12 07:41:20.297: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, largest site's AP (6.0.199.4)
*Nov 12 07:42:31.928: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC1, random site's AP (6.0.196.0)
When I checked the warehouseAPs, which are configured as local in the WLC2 (6.0.196.0), there was nothing like this in the logs. Logs are clean.
But when H-REAP is configured for these APs, the clients should not be disconnected when the CAPWAP goes down? And this whole "process" seems to last just for a second. Not sure if this is the real reason for these client disconnections, but at least this is not normal. I haven't heard complaints from smaller sites, even when APs at them also does the same.
I don't feel great to update the WLCs for the version 7.x, because it just seems to be new feature release, but if it fixes these, then I should think about it. Has someone, who had these same problems, got this fixed with version 7? Or has TAC provide some other patches for this?
Thanks,
Joni

IPhone 5S loose connection with soundlink bluetooth bose

The iPhone 5S loose the connection with the soundlink Bluetooth Bose ? When I connect iPhone 4 with the some device there is no problem.
Do you know if there is some solutions ?
Thank you very much
Zampilla

Not a generic issue ,my iPhone 5S works with Sounddock 10, soundlink and soundlink mini all perfect
Check to see if you have too many paired devices on Bose and sometimes you can only pair with one device at a time

Router looses connection with modem

My WRK54G wireless router keeps losing connection with my Comcast broadband modem. My connection with the router remains, but I lose internet connection. After rebooting the modem and router, my connection lasts no more than 5 minutes.
I tried to upgrade my Firmware but it did not install corrctly. (error during upgrade).
Any ideas on what I can try?

If you loose the connection on all the computers(wired and wireless) then, you should connect a computer straight to the modem and test the internet connection...See what happens and if you face the similar problem then it is not your router...
If you have stable connection straight from the modem, then, you should upgrade your router's firmware...
As the upgrade failed, you need to download TFTP Utility...Also download the router's firmware from here , make sure you select the correct version and then download the firmware...
Double click the tftp.exe file and click run :
For Server- Enter the IP Address of the router that you assigned. By default, the router is 192.168.1.1...
For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
For File- Click the triple “…” button and browse for the .bin firmware file...
Click Upgrade button to start upgrading. A progress bar should show up to show the progress.
Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

PC Running LabView Program Looses connection with the FieldPoint FP1600 4.11

If works for a while and looses communication with the PC. I tried to ping the module but it is timing out. If I reset the Power on the modules it starts working again. Any remedy of this problem

I had a similar problem. I checked and tried lots of things. I finally solved it by: 1) moving the FP1600 to a different location and 2) putting a ferrite bead on the network cable. I think it is 2) that solved the problem. These devices are apparently very sensitive to EMI. You can read more about EMI protection in the knowledge base article:
http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/2758edc0fb26d27a86256a6b0073b5d4?OpenDocument
Another suggestion was to run the FP1600 with no modules attached to see if the problem was coming from the modules. They could then be added one-by-one to see which one, if any, was causing the problem. The solution might again be EMI protection.
Rich

My E71 looses connection with Motorola 820's when ...

When I walk my dogs I can't listen to music because my E71 and Motorola 820 won't stay connected. If I'm sitting still I can listen to all the music I want but when I go outside and walk the music cuts in and out, speeds up, slows down then finally looses connection all together. I tried searching the forums but did'nt find an answer to my problem, I also tried searching for a list of confirmed headsets but could'nt find any.
Thanks alot
Pat

Troubleshooting Wi-Fi issues

Speedgrade loose connection with all volumes.

Dear SpeedGraders
I am working with R3D loaded from EDL 24 fps. Last Speedgrade CC. OSX 10.8 upgraded to 10.8.4
MACPRO 12 CORE ATI 5770
The RAW files readed from internal RAID 0.
During the session lost connection with the clips. When try to save proyect i realize that nothing could be written by SG. Check all volumes. Internal and external. Also a pendrive for save a look and same problem. Speedgrade see all the volumes as READ ONLY and could't writte on it.
Outside SG system writes and read on every volume.
Thank you for your help.
Sebastian Toro
BS AS. ARGENTINA

I found that if i close the current timeline the system appears to return to normal.
I can later save a new proyect or a look or browse the r3d files that went offline in the past minute with the ORIGINAL timeline and proyect
any help?
best regards

Double IP-adr. and loosing connection with Home Share.

I'm getting two IP-addresses for my Apple TV3, Why? (both WiFi & Cable ??) And I also loose connection to Homeshare/iTunes, have to restart iTunes every now and then. Also have a Apple TV2 in the network. When I only had Apple TV2 in the network I experienced none of these problems.

I see them in the list in my router (list of connected device and their IP-adr). I have also named my device "Apple TV Upstairs" but when it getting more than one IP-adr the name in the router, wich also is displayed in Airplay from for example in iPhone, change to "Apple TV Upstairs (2)".

Wired Time Capsule is loosing connection with my 1 gigabit connected MacPro

I have MacPro connected with my Time Capsule 1TB disk.
MacPro is connected with Cat 6 50 feet cable so a 1 gigabit wired connection.
before i had a Netgear GS 608v2 Switch in between. But I removed that to see if that would solve my issue.
But the issue has now happened 6 times now:
I start to backup and after a while the Time Capsule hard disk disconnects (the internet keeps on working fine) because i have an an audio streaming playing at the same time.
I have MacOS 10.5.2 and everything is updated to latest versions . My Macmini G4 has been copied fine so far. But my MacPro keeps on failing.
In my system.log I get following errors:
Apr 13 16:00:44 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: doing reconnect on /Volumes/MVO's Time Capsule-1
Apr 13 16:00:44 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 16:00:50 Quad-Raid kernel[0]: AFP_VFS afpfs_Reconnect: posting to KEA EINPROGRESS for /Volumes/MVO's Time Capsule-1
Apr 13 16:00:50 Quad-Raid KernelEventAgent[98]: tid 00000000 received VQ_NOTRESP event (1)
Apr 13 16:00:50 Quad-Raid KernelEventAgent[98]: tid 00000000 type 'afpfs', mounted on '/Volumes/MVO's Time Capsule-1', from 'afp_0TSQUm0Xl2BJ00mmYF0Pyetl-1.2e00000a', not responding
Apr 13 16:00:50 Quad-Raid KernelEventAgent[98]: tid 00000000 found 1 filesystem(s) with problem(s)
Apr 13 16:00:50 Quad-Raid loginwindow[97]: 1 server now unresponsive
Apr 13 16:00:55 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 51.
Apr 13 16:00:55 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 16:00:59 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 51.
Apr 13 16:00:59 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 1 seconds and then try again
Apr 13 16:01:00 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 16:01:04 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 51.
Apr 13 16:01:04 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 2 seconds and then try again
Apr 13 16:01:06 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 16:01:09 Quad-Raid dnsupdate[113]: Caching external address
Apr 13 16:01:20 Quad-Raid loginwindow[97]: 1 server now unresponsive
Apr 13 16:01:41 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 51.
Apr 13 16:01:41 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 16:02:09 Quad-Raid dnsupdate[113]: Caching external address
Apr 13 16:02:16 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 51.
Apr 13 16:02:16 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 16:02:51 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 51.
Apr 13 16:02:51 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1

Sorry but this doesn't help, because this article is talking about streaming to Airport Airtunes, but my problem is that Time Machine stops backing up after a while because the Time Capsule isn't connected anymore. Because the Time Capsule is disconnected:
Here just my 8th attempt to backup with Time Machine:
Apr 13 20:52:23 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 60.
Apr 13 20:52:23 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 20:53:10 Quad-Raid dnsupdate[113]: Caching external address
Apr 13 20:53:38 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 60.
Apr 13 20:53:38 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/MVO's Time Capsule-1
Apr 13 20:54:10 Quad-Raid dnsupdate[113]: Caching external address
Apr 13 20:54:53 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/MVO's Time Capsule-1 failed 60.
Apr 13 20:54:53 Quad-Raid KernelEventAgent[98]: tid 00000000 received VQ_DEAD event (32)
Apr 13 20:54:53 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: max reconnect time reached 646 > 600 /Volumes/MVO's Time Capsule-1
Apr 13 20:54:53 Quad-Raid KernelEventAgent[98]: tid 00000000 type 'afpfs', mounted on '/Volumes/MVO's Time Capsule-1', from 'afp_0TSQUm0Xl2BJ00mmYF0Pyetl-1.2e00000c', dead
Apr 13 20:54:53 Quad-Raid kernel[0]: AFP_VFS afpfs_DoReconnect: posting to KEA to unmount /Volumes/MVO's Time Capsule-1
Apr 13 20:54:53 Quad-Raid KernelEventAgent[98]: tid 00000000 found 1 filesystem(s) with problem(s)
Apr 13 20:54:53 Quad-Raid kernel[0]: AFP_VFS afpfs_unmount: /Volumes/MVO's Time Capsule-1, flags 524288, pid 98

Problem With loosing connection with wired PC

I have a model WRT54GS wireless router. My computer is wired into the back of the router. I loose the connection to the internet sometimes and when I check the connection status it says my computer is connected to another Router. Then it asks me if I want to configure it. If I turn the router off and on it will run again. The firmware version is 7.5. Can anyone help with this issue?

Do you use the sleep or hibernate mode? I have a similar problem, v 8.0, but so far the only time I lose the connections is when the computer goes to sleep. If I leave it up, the bits keep on moving. Just curious.
Treg

Loosing connection with my xbox360

Similar Messages

Maybe you are looking for