Loosing internet connecti when removing router from airport extreme network

Hello. I have an older airport extreme: the alien one. For years I have had the following setup:
Modem --> Belkin Router --> Airport Extreme --> wireless signal to macbook and hardwire line to mac pro. There is also an airport express downstairs acting as a relay to boost my wireless signal. At the time i did it I had other computers so i needed the router to distribute the internet signal. I no longer need the extra capacity as I now only have a wireless macbook and a wired mac pro. Unfortunately when I disconnect the Router and connect the modem directly to the airport I no longer get internet service at either computer. I can't figure it out. The Airport Extreme is already sending all the signals to the two computers...the router is just sitting in the middle doing ostensibly nothing at all. Why, when I take it out of the loop does everything stop working? Thank you!!

Welcome to the discussion area!
Your AirPort Extreme was configured in "Bridge Mode" when it was used with the Belkin router.
Since the Extreme is now the main router, you must configure the Connection Sharing setting for "Share a public IP address".
If you are still using Tiger 10.4.x as your profile indicates, you may still have the application that came with this operating system...AirPort Admin Utility. I cannot remember back 4-5 years to tell you much about this.
If you have upgraded to Leopard or Snow Leopard, you'll use AirPort Utility.
I can help you if you have AirPort Utility. Post back if you need help.

Similar Messages

Airport Express disconnects wired internet connection when attempting to extend Airport Extreme WiFi network

I just purchased and airport express to extend my wifi network. My base station is an airport extreme, I have one wired connection and a wifi network. When I go through the recommended steps to set up the express and "extend the network", the airport extreme will no longer connect to the internet via ethernet. I have tried various settings and can't seem to resolve the problem. Any assistance would be much appreciated.

Ok so we now have a solution to the problem. A friend of mine came round to work this out with me last night and we were able to get it working, but it is not as easy as I had hoped. Fisrtly we plugged the airport express into my router using the ethernet cable (for this I am using an Airport Express Base Station") and in airport utilities selected the airport express. In edit, we then gave the airport express a new range of IP address which did not conflict with any of the other applications that I have already assigned. We also named the Airport Express with a distinguishable name. We then waited for the changes to be registered then unplugged the Airport Express from the router. I then plugged my AppleTV via HDMI into a tv to test it and selected the new wifi network with the new Airport Express distinguishable name. I was able to watch a video that I have on my ipad directly on my tv without being connected to the internet, and was able to play Airplay presentations.
No the easiest solution, and certainly not something that anyone at Apple has talked me through in my lengthy conversations with them at Applecare.
Hope this helps.

Trying to connect Verizon wireless router to Airport Extreme but error says Ethernet unplugged.

Trying to connect Verizon wireless router to Airport Extreme and error says Ethernet Unplugged.

So, AirPort Utility running on the Windows Vista desktop can "see" the AirPort Extreme and displays its icon, but gives that error message at some point in the setup process? How far does it get?
Other questions that may help me (or somebody else) understand your problem better:
Which of the pieces were verified as working before the introduction of the AirPort Extreme?
Did you have the desktop computer attached to the Verizon GT704WGB with one of the Ethernet cables you are now trying to use? Which one? Have you tried the other one to be sure it also works?
Are you using the same port on the GT704WGB? Have you tried another one?
If the desktop has multiple ethernet ports, are you using the same one?
Had you done any special configuration of the ethernet port on the Verizon GT704WGB to get it to work with your desktop?
What category ethernet cable are you using? 3? 5? 5e? 6?

When I reopen my computer (macbook pro) it connects to my dsl connection and not to my airport extreme network that I created

I purchased yesterday an airport extreme, everything works fine, but the thing is that when I close my laptop (just shutting down the screen) and then reopen it, instead of conecting to the airport extreme network I created, it connects to my DSL connection. Is this normal? Do I have to keep entering my own airport extreme network after I close/shut down my computer? Thank you very much

Hi Bob, I solved it, it had to do with the preferred networks. But thanks anyways!

How to connect a ADSL router to AirPort Extreme?

Hallo,
my local internet service provider forces all costumers to use their modem/router to connect to the Internet using a DSL connection.
I have one external public IP (v4) and the router has an editable IP for the LAN set to 192.168.1.1 .
The ISP router can act as DHCP server and NAT; I can disable the DHCP.
What I would like to do is connect it to the Airport Extreme WAN port and give all the control to the Airport extreme: I want to use his DHCP server, NAT, port forwarding etc.
My problem is that I am able to have Internet connection only if the ISP router has DHCP control and Airport Extreme is set to Bridge mode.
In this configuration, in the Airport Internet configuration panel, the connection is set to Ethernet, IPv4 is using DHCP, Airport IP is 192.168.1.133 and the ISP router has 192.168.1.1 . I also have the DNS IPs set to the ones suggested by the ISP and Bridge mode.
In this way it works: all computers can share Internet connection.
What I am trying to do is:
- disable DHCP in the ISP router;
- in the Airport extreme Internet panel I choose to manually setup IPv4 and I type the same vales it is getting when set to DHCP mode: 192.168.1.133 for the Base and 192.168.1.1 for the router using the ISP dns and I select Share pubblic IP. In the DHCP panel I choose 10.0.1 class.
I save changes and... I got that Internet is no working anymore and I cannot access the ISP router control panel.
Does anybody have suggestion about things to try to not use ISP router DHCP or configuration changes I could try?
Thanks in advance for any help about it!

Thanks for the reply,
at the end it seems that my airport extreme works too BUT with an error message saying "double NAT" and the front led turned to yellow. I have ignored such error because things seems to work and so the led color goes to green.
What I had to do here is:
- set previous router to IP 192.168.1.1
- turn off DHCP on my previous router;
- leave on the NAPT (NAT) service on previous router and set it with start and stop address to the same IP I am using for the Airport Extreme (192.168.1.100);
- open all ports and services on previous router by faking the mac address of the Computer's NIC I was using to configure router. I say faking because previous router wants to know for which computer the ports have to be open, so I had to use the same mac address of the Airport extreme. I cannot type it, previous router will get it automatically when configuring it.
- on the Airport Extreme, Internet side, I had to manually configure Internet options using Ethernet mode: I set the IP 192.168.1.100 for the Airport base. Then I have enabled DHCP on class 10.0.1.x .
Airport extreme seems to work with all features now, I hope that "double NAT" warning will not create any trouble. Anybody knows about that?

Do I have to set up internet connection? I already have Airport Extreme

Just purchased a Time Capsule to back up two MacBook Pros to save iPhotos and stuff.
Do I need to have the internet to do this?
Can I just set up the TC as a network alone?
Will I have to change networks from the Airport Extreme to the TC just to do the Time Machine back ups?
Not sure of any of this from the instructions from the book that came with the TC.
Thanks in advance for the help!
Dave

Just purchased a Time Capsule to back up two MacBook Pros to save iPhotos and stuff.
Do I need to have the internet to do this?
No, an Internet connection is not required to perform Time Machine backups.
Can I just set up the TC as a network alone?
Yes.
Will I have to change networks from the Airport Extreme to the TC just to do the Time Machine back ups?
Yes, if you are planning on doing wireless backups. The other option is to reconfigure the TC to "join the wireless network" created by the AirPort Extreme.

Pc with windows xl/sp3 can't connect / acquire ip address from airport extreme; meanwhile, my macbook in connecting fine. We have a wpa2 personal password

My husband's Dell with Windows xl (sp3) can't get an ip address from our new airport extreme. Nor can my daughter's Windows 7 computer. There are no firewalls in place. Both computers worked with my old Airport, though it was sssslllllllowwww. My Macbook works fine and is super fast compared to the old airport. We are using a wpa2 personal password.
Anyone out there have a cure for this problem so we can hook up those sad pcs?
Thanks a lot.
Elizabeth

First, make sure that the new Airport is configured exactly the same as the old one. Hopefully you saved the configuration settings in a file and can look at them to be sure.
If the Windows PC's can't connect with the same password, it's possible that the PC's were using an older wifi protocol like 802.11a or b. The new Airport is backwards compatible but has to be setup that way check to see what versions of 802.11a the windows computers support and make sure that the wireless mode of the airport is setup to accomodate them.
Can the PC's get an IP address if they are connected to the AirPort using an ethernet cable? If they can, that would help naorrow things down to a wireless issue and not some other configuration problem.

Lost connection to Westell router after Airport Extreme Update

I've looked through the discussions and have seem similar issues but haven't found one that I could say "that's it!"
I use the airport card in my MacBook OS X 10.4.11 to wirelessly connect to my Westell versalink router and have done so for over a year. I don't have an AEB. During updates, I left the airport extreme update checked. Why? I probably wasn't paying enough attention.
So now I cannot connect at all - at home. It's stating that my password is incorrect. I can connect at work; no password is required.
I went to the Westell website and changed my Network (SSID) name and password. Now, I'm picking up this new network but I'm still being told the password is incorrect.
Can I uninstall the Airport Exteme Update (and pray that it works) or is that too easy an answer?

You are not alone, have a look at this thread:
http://discussions.apple.com/forum.jspa?forumID=1015&start=0
Unfortunately, it appears that the 2007-02 update has broken Airport running on Macbooks and Macbook Pros that attempt to access wireless routers using WPA. I've spent a lot of time looking for a solution, and at this point there appears to be no reasonable fix until Apple corrects this serious flaw. If you have AppleCare, perhaps a phone call to them would help them become more aware of the situation. Until they do, many of us are without the use of Airport, particularly where it is not possible to switch off WPA in a shared environment (such as my office).

PC's disappear from Airport Extreme Network

I have an Airport Extreme and three computers (MacPro and 2 PC's) Ethernet hard-wired to it for internet connection -- which works fine on all three computers. I set up a network between the three computers about a month ago and it worked perfectly for two weeks, then the two PC's disappeared from the Mac's Finder, and the "shared" marker also disappeared. About a week later, everything reappeared and again worked fine -- now it is gone again. I am confused because there is nothing wireless in play and when the computers appear in the "shared" list, everything works flawlessly, for as long as it lasts. I have been reading about a possible problem with Airports losing printers when attached through a hub, but that is not the case here either, the printers work fine. Does anyone have any thoughts? I really appreciate your time.

check the network setting... I mean all PC + Mac accessing the same network group... check on your airport utility - advanced - wins and select the workgroup named workgroup from the drop down menu, or whatever the name of the network is. also on systems preferences - sharing - file sharing should be on, and select options on file sharing and select afp, ftp and smb.
all these things always with firewalls off. keep firewalls off until you see the pc always and then start working on firewall settings

Constant Disconnection from Airport Extreme Networked iMac (late 2009)

I keep trying to copy fairly large files (2-7GB) over my Aiport Extreme (latest—5th generation) network from a early 2011 Macbook Pro to a 27" iMac (late 2009), and I keep getting disconnected from the iMac while the file is copying. I've tried repairing permissions on every computer in the house and restarting them, but I'm still having issues. I have no issues copying files to another late 2011 Macbook Pro in the house, so it seems to be happening only when I copy them to the iMac. The iMac is running Snow Leopard and the Macbook Pros are running Lion, so could that have something to do with it?
Additionally, I had been trying a wireless extended network with another previous generation Airport Extreme, but I found the connection wasn't much stronger with the extension, so I've just been leaving the second Airport Extreme unplugged. I've had that unplugged for months and haven't had any issues, so I don't think that's the problem.
I'm hoping this isn't a sign of something being wrong with the Aiport card in the iMac. Anyone have any ideas?

Bump?

Problems connecting multiple macs to an Airport Extreme network.

I think this problem is similar to a previous post, but is individual in some ways.
I have 2 Airport Extreme basestations covering a large flat connected by Ethernet extending a single network. I did try to extend the network wirelessly, but this was plagued with problems where the network would work for 10 mins, then drop out as I think the basestations are slightly too far apart.
Connected to the network are a number of machines:
Wirelessly we have 3x iPhones, 1x G4 Cube, 1x iMac (current model), 2x MacBook Pro (previous model) & 1x PC.
Wired via a hub is an Apple TV, PS3, Nintendo Wii, Denon Home Cinema Amp, PS2
For aprox 6 months I have had major problems connecting all the wireless machines at the same time. I have played around with the security as per previous posts with varying degrees of success.
I seem to have the most problems with the iMac. The iMac will not join the network when there is any form of wireless security. Every time I try to set up a password it hangs when trying to join and I finally get the "There was a error joining xxxx network".
After more playing around I managed to get all the machines working by having no security on the network and locking the network down by MAC addresses.
Since last Thursday I now have a new problem. The iMac joins and stays on the network perfectly, but the second my second MacBook Pro is switched on and joins the network, the internet connection on the iMac drops out. In addition, as we use the iMac as a media server, all other machines connected to the iMac for either file sharing or iTunes sharing then get the error "the remote machine is failing to respond. Please check firewall settings if there are any". What is strange is that the iMac remains on the network, full signal, independent IP address and the second the MacBook Pro is switched off, works perfectly again.
I have tried wiping both the iMac & the MacBook Pro and re-installing their operating systems, but this only solves the problem for aprox 24 hours then all of a sudden the issue re-appears.
Can anyone out there help?

Let's double-check the AirPort Express Base Station's (AX) settings ...
Perform a "factory default" reset of the AX
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, check the following settings:
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing AEBSn's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

Removing Clients From Airport Extreme

Is there a program out there(whether it be for a mac or pc) that is capable of removing people that are connected to my airport? For instance, if my neighbor is using my wifi, is there a way to disconnect him?

Is there a program out there(whether it be for a mac or pc) that is capable of removing people that are connected to my airport?
None that we are aware of.
The most effective way to remove someone that you suspect may be using your network is to change your wireless network password.
Macintosh HD > Applications > Utilities > AirPort Utility
Click Manual Setup
Click the Wireless label below the row of icons
Enter a new password* (write this down)
Confirm the new password
Click Update at the lower right to save your new settings
*A good password is a non-dictionary word consisting of letters and numbers
Keep in mind that you will now need to enter your new password to log on to your network.

Trouble with internet connection when using extreme to join wireless network

I have an airport extreme that I want to use as an ethernet hub. I have successfully connected it to my wireless modem, and I have a solid green light; however, when I connected the ethernet to my tv/computer/anything there is no internet connection. I tried powering down everything in order and rebooting as appropriate modem then router then computer, but still not internet connection. Any suggestions.

The AirPort Extreme does not provide any routing functions when it is configured to "join a wireless network", so the Ethernet ports are not active in this type of setup. The only thing that really functions is the USB port, which could be used for a remote printer or hard drive.
If you have another Apple "n" wireless router acting as your main base station, you can configure the AirPort Extreme to "extend a wireless network". The Ethernet ports are enabled in this type of setup....and the Extreme will provide more wireless coverage in the area where it is located.

Using ARD remotely connecting to work computer with Airport Extreme...

So I've looked through the forums, over the interwebs, through the ARD PDF manuals online and I'm coming up short. Ugh.
I want to connect from my home laptop to my desktop at my small business where we're using an Airport Extreme for a router. I can NOT figure out how to get this configured to work. We use ARD within the business, so on the same network, no problems. With the router, I'm guessing I need to get the computer setup to have a locked in IP and whatnot but no where can I find the instructions that tell me EVERTHING I need to do. Can someone here point me in the right direction please or hit me over the head with a 2x4 of exact instructions!
Thanks for your time! Shawn

Hi Shawn,
So the steps listed bellow assume some things. They assume that the Airport Extreme Router your configuring is connected directly to the internet connection. And that the Airport Extreme is the only router between your computers and the internet.
That means we're talking about say a DSL modem plugged directly into the Airport Extreme, or a cable modem. in ether case, this assumes that said modem, is not acting as an internet router.
If your modem has multiple ethernet ports on it, or has a little antenna sticking out of it, then your modem is probable also a router, and these steps listed bellow will probable not work.
Also these steps are so one person, can connect to one computer at your work.
Open Airport Utility:
go to the dock
Click on the finder
go to the menu bar
Click on the "Go" menu
Chose "Utilities" from the "Go" Menu
double Click on "AirPort Utility"
Access the Base Station:
Double Click on your Airport Extreme BaseStation that is your internet connection router.
a new window should pop up with your Airport Base Station as the Window Name
Configure Static Address for the computer you want to connect to via ARD:
Click on the internet Icon from the toolbar
Click on the "DHCP" tab
For "DHCP Reservations:" Click on the "+" button
For the "Description" put "ARD"
For "Reserve Address by:" set "DHCP Client ID"
Click the "Continue" button
For "DHCP Client ID:" set "ARD"
write down the number in "IPv4" address field
Click the "Done" Button
Configure routing to ARD computer:
Click on the "Advanced" icon from the tool bar.
Click on the "Port Mapping" tab
Click on the "+" button
for "Service:" Chose "Apple Remote Desktop"
for "Private IP Address:" copy the exact IP address you wrote down in step "3. 8)"
Click the "Continue" button
Click the "Done" button
Click the "+" button
For the pulldown menu "Service:" Chose "Remote Apple Events"
for "Private IP Address:" copy the exact IP address you wrote down in step "3. 8."
Click the "Continue" button
Click the "Done" button
Click the "+" button
For the pulldown menu "Service:" Chose "Remote Login - SSH"
for "Private IP Address:" copy the exact IP address you wrote down in step "3. 8."
Click the "Continue" button
Click the "Done" button
Click the "Update" button.
wait for the Airport Extreme to update, and for your computer to reconnect to the airport extreme. (make sure you can load and browse websites.)
Configure the ARD computer to use the correct IP address:
Go to the computer you want to be able to remotely connect to
On that computer, Go to the menu bar
Chose the "Apple" menu bar
Chose "System Preferences…"
Click on the "Show All" button
Click on the "Network" icon
For the active network connection, (the connection on the left side with the green dot), click on it
Clock on the "Advanced…" button
Click on the "TCP/IP" tab
for the "DHCP Cient ID: field put "ARD".
Click the "OK" button
Click the "Apply" buttonNOTE: Under "Status" you should see "(connection name) is connected to (airport base station name) and has the IP address (IP address)." the "(IP address)" address displayed should match the IP address you wrote down in step "3. 8."
Find out what your public internet IP address is.
On the computer you wish to connect to over the internet, goto http://whatismyipaddress.com/
when the web page loads, you should see "IP Information:" fallow by a number like 192.168.0.1, write down what ever number it is.
At this point you should be able to connect to the computer remotely
connect to the internet from another location.
open Apple Remote Desktop
go to the file menu
chose connect to computer using ip address
set the address to the address to the IP address you wrote down for step 6. 2.
use the same password as you used to connect to the computer at work using ARD.
So here the catch. If your router gets reset... well then your going to have to configure it again. Also all the same rules you have to connect to the computer at work, also apply to connecting to the computer from over the local network. That means your computer need to be on or sleeping. And if it's sleeping it need to be configure to wake for network access.
Also some network connections change. When it comes to internet connections, some connections are static IP, while other connections are DHCP. If your connection is static... great! if it's DHCP, your address may change. If it dose.. well then your ability to connect will break. And then you'd have to do step 6 & 7 again.
Of corse there are ways around this. But that's kind of another conversation.
Some internet locations may block your ability to connect to your computer at work. This is very common at schools, and companies. Basically any place that tries to control your ability to browse the internet, may block remote access to computers; because a remote computer would completely by pass their web filter.
ALSO there is an easier option. As far as setup. There are programs designed to make remotely accessing your mac as easy as possible. For instance there is LogMeIn or Slack. With both of these programs, it's simple. make sure your computer is always on. Then install the software. Create an account with the service. And then you can connect to the computer almost any where by going to their website.
This option requires no router configuration. It handles DHCP. It's designed to work in as many locations as possible.

Automatically connecting a WEP encrypted Airport Extreme network

My Powerbook when it turns on has no trouble connecting to my WEP encrypted Airport Extreme network. My iMac G5 on the other hand requires a manual connection to the network. This even though my Apple menu -> System preferences -> network -> configure -> Airport has "by default join a specific network" with username and password selected.
Why does the Powerbook automatically connect when the iMac does not? Both are sitting side by side?

Well a variant of that article did work. I called AppleCare. They had me while I was still not connected, create a new location, Configure my airport settings, and lo and behold, preferred networks was there, I was able to edit my password for my WEP connection, hit Apply Now, restart, and Change All keychain passwords, and my network automatically connected on the next login.
Thank you.

Loosing internet connecti when removing router from airport extreme network

Similar Messages

Maybe you are looking for