Lose settings after power cycle.

I noticed the iPhone (firmware 1.1.1) will occassionally lose internet WAP settings for my carrier after power cycling (turning off then back on). The top left menu displays the correct wireless carrier and has the "E" for EDGE coverage but fails to access the network via EDGE for email/internet browsing due to the WAP settings are erased. I have to then enter the WAP settings again. Has anyone else experienced this?

I reinstalled my firmware but couldn't find a solution to this. After installing the latest firmware 1.1.2 I no longer experience the issue with the reset settings.

Similar Messages

SRW2024 Ports lose comms after power cycle

Hi
We have a medium size network consisting of about 25x SRW2024 switches and 8x SGE2000 doing the routing in layer 3 mode. We have about 100 vlans in total and everything is setup and all works fine until we have a power issue. Sometimes when the power is turned off to certain layer 2 switches for about 10 min or more and then back on sometimes the devices connected to them will not communicate. I can see them connected if I go into the webpage of the srw2024 but no communication until I power cycle the device connected. Is this a problem with the device conected or with the srw2024?
This doesn't happen all the time but cannot find any settings that might cause this. The ports on the switch are set to 100m speed and mdix.
Any help would be appreciated.
Darren

I reinstalled my firmware but couldn't find a solution to this. After installing the latest firmware 1.1.2 I no longer experience the issue with the reset settings.

Reset TC with Original Settings after Power Failure

TC blinks yellow after power failure. How can I reset to original (before power failure) network settings?

Here you go: How to reset Time Capsule

Guest domains fail to boot from SAN disk after power-cycle

Control Domain Environment
# uname -a
SunOS s0007 5.10 Generic_139555-08 sun4v sparc SUNW,T5440
# ./ldm -V
Logical Domain Manager (v 1.1)
Hypervisor control protocol v 1.3
Using Hypervisor MD v 0.1
System PROM:
Hypervisor v. 1.7.0 @(#)Hypervisor 1.7.0 2008/12/11 13:42\015
OpenBoot v. 4.30.0 @(#)OBP 4.30.0 2008/12/11 12:16
After a power-cycle the guest domains did not boot from SAN disks, they
tried to boot from the network.
# ./ldm list
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME
primary active -n-cv- SP 16 8G 0.5% 4d 20h 46m
s0500 active -t---- 5000 8 8G 12% 4d 20h 46m
s0501 active -t---- 5001 8 4G 12% 4d 20h 46m
s0502 active -t---- 5002 16 8G 6.2% 4d 20h 46m
s0503 active -t---- 5003 8 2G 12% 4d 20h 46m
s0504 active -t---- 5004 8 4G 0.0% 4d 20h 46m
s0505 active -t---- 5005 4 2G 25% 4d 20h 46m
s0506 active -t---- 5006 4 2G 25% 4d 20h 46m
s0507 active -t---- 5007 4 2G 25% 4d 20h 46m
s0508 active -t---- 5008 4 2G 25% 4d 20h 46m
Connecting to console "s0508" in group "s0508" ....
Press ~? for control options ..
Requesting Internet Address for 0:14:4f:fa:b9:1b
Requesting Internet Address for 0:14:4f:fa:b9:1b
Requesting Internet Address for 0:14:4f:fa:b9:1b
Requesting Internet Address for 0:14:4f:fa:b9:1b
If we reboot the quest domains now, it works.
It seems the disks are not ready at the
time the guest domains boot.
We see this on systems with many guest domains.
Is there any logfile, where we could find the reason for this?
Or is this a known issue?

Press F12 on boot to choose CD/DVD as a temporary boot device.
My hunch is that there's something wrong with the SSD itself, though.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

IPod 5th gen loses settings after reset

After a reset (menu & select buttons) my iPod video loses settings. Backlight timer, bass boost, shuffle mode, max volume, etc. all go back to default. Battery is fully charged. Is this normal?

I'm not sure exactly which settings are reset and which aren't, but I highly doubt that your iPod needs fixing on these matters.

WRT310N version 1: Port 4 light is on but nothing is connected after power cycle

I have the WRT310N version 1 with the latest firmware date Dec 2009. Everything is working great except when I turn off the router and power back up. I am only using port 1 but after a power cycle both port 1 and port 4 lights are on and I can't connect to the Internet. If I keep unplugging the router (2 to 5 times) with 30 secs between I can eventually get just the port 1 light and then everything is good to go until the next power cycle. I don't need or want to keep my router on 24/7 so any advice is greatly appreciated. Thanks in advance!

Hello.
Try to hard reset the router by pushing the button for 30 secs then power cycle it again.
What if you plug the computer to the other ports? Do you experience the same problem? Have you tried a different cable to connect the computer?
Not sure if reflashing the firmware could help on this one but you could also give that a try. click here
Make sure you know the hardware version of your router before reflashing the firmware. It is found underneath the router itself.

Help! Fast Internet only for short while after power cycling of AEBS

The Charter Communication tech came out to check why we weren't getting the advertised 20meg speed. Well, the speed out of the modem is ~19meg and if I plug in the laptop directly to the brand new Airport Extreme router (firmware 7.4.1), we do get the fastest speed.
I ditched the setup I had with dual band separate networks, since we don't actually transfer files between computers much. I just want fast Internet for downloads/uploads.
I have the network setup on auto bands and auto channels (and I have tried setting the channels manually). We don't have many neighbors so there isn't a lot of interference that I can tell.
If I unplug the router and plug it back in--then the wireless network speed is fast ~19 megs. However, after less than 30 min. the network bogs down and becomes 5-7megs. Then if I power cycle, it goes right back up to 19megs.
Why????

Hello,
There have been issues with Roboform in the past: http://kb.mozillazine.org/Firefox_crashes#Roboform
Try disabling it and see if you still have browsing issues.

Auto Answer will NOT stay on after power cycle or reset - C20 TC7.3.0 UCM 10.5SU1 registration

As the title suggests, I've got 2 C20 codecs running the latest 7.3.0 code I can download registered to UCM 10.5.1 SU1. Power cycling or resetting them causes the auto-answer to default to off. There is still no way to change auto-answer from within UCM, and TMS cannot manage the device anymore.
I've found a couple of instances of this with older TC and UCM code, but it seems this issue continues today.
Any ideas?

Saw that and it ended up being the right direction, but since I was on a different version I wasn't able to use that device pack.
So, I found out the following from TAC:
Auto-Answer became a configurable field presented to UCM in TC7.2.x, but the appropriate management fields on the web pages didn't become available until later in the device pack. I read through a couple of device pack readme's and I didn't see anything related, but sure enough installing 10.5.1.11005-2 presented the fields and that works fine now.

JDeveloper start VERY slowly first time after power cycle

I'm running JDeveloper Version 9.0.2 in a classroom situation on about 15 Win-2000 machines (aprox 700Mz). The first time jdevw.exe is launched after power up, it takes 5-7 minutes before the splash screen appears. Re-launching the applcation subsequent times takes 10-20 seconds for the splash screen to appear. The taskmanager show 100% CPU Usage during the 5-7 minute period. Any suggestions?
Thanks,
Ralph Wieland

Do you have any virus checker installed? Some of them want to check each and every .zip and .jar file before they OK the use of these libraries.
Georg
JDev Team

FATAL Error After Power Cycle- GVRP related?

Hello all,
Happy New Year!
I have a network of four 300 Series small business switches. All are running software version 1.3.5.58 (latest version).
Three of them are connected by 2 Port LAG groups to the central switch which in turn connects to the internet facing router. There is no loops in the architecture and spanning tree is running. There are a total of 4 VLANs and GVRP is enabled with the four VLANs statically created on the main switch.
Normally everything runs very happily and is perfectly stable.
However, a power failure this morning resulted in a power cycle on two of the switches. They did not recover gracefully and kept restarting.
I removed the ports from the LAG groups in the main switch (not impacted by the power cycle) and then rebuilt them to recover connectivity and restore normal operation.
Both of the switches which restarted had multiple entries in their log files like this:-
%GVRP-F-NOSTATREG: GVRPP_checkStaticToDynamic_update: Port isn't Statically registered on vlan 100 ***** FATAL ERROR ***** Reporting Task: BRMN. Software Version: 1.3.5.58 (date 10-Oct-2013 time 17:15:41) 0x16adbc 0x166f28 0x6df2b0 0x48fad8 0x4903e8 0x490608 0x51a234 0x79dfd8 0x7b9f8c 0x7c1500 0x445d 88 0x41e04c 0x7d4c80 0x61cb68 0x1223f0 ***** END OF FATAL ERROR *****
Has any one seen this before? Have I made some "rookie" mistake with by GVRP configuration?
Kind Regards,
Andy.

Hi Andrew, the GVRP database is kind of a strange creature (the protocol itself is just strange). By removing a VLAN or interface from the GVRP database, when the join message is sent it will send an update to the downstream switch. I suspect that by removing the LAG there was an unintended database change (in fact the database on the receiving switch didn't have the desired database as you modified the trunk which strips all VLAN). So what happens is the downstream switch "defaulted" to 1 vlan then the re-establishment of the LAG sent more VLAN and the GVRP database didn't match up.
Does this kind of make sense?
If you're in for a simple lab you can create a trunk between switches with multiple vlans tagged (do like 5 vlans, not just 2). Then remove one of those vlans off the master switch. Observe the behavior.
-Tom
Please mark answered for helpful posts

Must I reboot Windows after power-cycling the PXI?

The fans in the NI PXI-1042 are *noisy*!!! This thing is in a classroom and gets shut off everytime I turn around. Two questions: 1) is there any way to get around the reboot required to find the PXI cards on the PC every time it is power-cycled. 2) Where can I find quieter replacement fans for this thing?
Thanks,
Chris

Chris,
I don't know what type of connection you have (MXI-3 or MXI-4)... I have had some success with the following method:
With everything up and running, go to Control Panel >> System >> Device Manager (Hardware Tab). From there, expand the "tree" for System Devices. There you will see 'PCI Standard PCI-to-PCI Bridge'. Right-click on that and choose 'Disable'. The PXI chassis can now be turned off. When you are ready to use the PXI boards again, simply turn the PXI chassis back on, and then choose 'Enable' from device manager and the chassis and computer will link up once again. So, it does require some action up front, but it will save you from rebooting
I can't guarantee this will work every time and I'm not sure if it works for MXI-3 (I have MXI-4) but it may be worth a try.
<-*DrkOvrlord*->

Re: MSI Gaming 5 motherboard loses its BIOS settings after power outage.

Yup, it could be a short causing CMOS to clear whenever MB loses power for whatever reason. Also check JBAT1 (clear CMOS jumper) and insure there is no jumper or no bent pin(s) there. Check this 1st before going to the trouble of removing MB for testing.

Quote from: dmcconnaughie on Today at 21:37:53I have been wondering the same thing. I have a corsair hx750i and have connected to the CPU with the 8 pin connector. I don't have a 4 pin connector but the psu also d...

LAP1142 looses config after power cycle

We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
Best Regards,
Augusto

I would just open a tac case as it might be an issue with the APs itself.
Sent from Cisco Technical Support iPad App

RV042 v3 (v4.2.2.08) loses config after power loss

I have two RV042 units - both v3 hardware and both with firmware 4.2.2.08.
Both units lose thier configuration and return to factory default after a power loss.
I've tried re-flashing the firmware in both units - no change.
I have the configuration backed up for both units, so it only takes me a few moments to restore them after a power loss, but shouldn't the units hold their configuration in NVRAM or some such?
Any ideas as to what I'm missing?
Thanks for any replies...
-- Ray --

Well the date set back to 1969 is a classic sign of a dead battery.
Check out things in Texas Mac Man's Battery, PRAM, PMU tutorial on the subject. His tutorial is a little dated (don't believe it even mentions G5's, or Intel Macs) but the info in it, except SMU and SMC not being included, still applies. Luck ! DALE

Nexus 7010 Loses Config after power off

Recently we installed a pair of Nexus 7010's and we recently moved them to an APC rack better suited for their size. Upon powering them up we found out that the VDC's lost their configurations. The VDC's and the alloated resources were still there as well as the default VDC configuration but the other 2 we have configured had their configurations missing. We have been observing best practices and saving the configuration to NVRAM with the copy run start comand as well as the copy run start vdc-all commands yet the configurations were still lost.
Can anyone shed some light on what the problem may be?
Thank you in advance for your help!

We had the same issue TAC told us to reset the supv
,,,,, you might want to save your config ;-) it worked for us

Lose settings after power cycle.

Similar Messages

Maybe you are looking for