Losing freeview signal

Up to now, I have enjoyed a strong signal getting all the freeview channels. But, I switched my vision box on , and a error message said, "Freeview Signal Poor Quality or too low level". I'm not too sure what is going on here, is it the fault of my vision box, or is it the fault of my ariel. Anybody else had this as well.

It is usually a fault with the aerial
check that it hasn't moved position and check all the connections are OK including any signal booster being used
no trees were harmed in the sending of this message but millions of electrons were terribly inconvenienced

Similar Messages

How can I get my iphone to stop losing the signal?

How can I get my iphone to stop losing the signal?

Thanks for the tip. If only I could find somewhere where I did not lose the signal.
I am based in the United Kingdom. The carrier is Orange.
I lose the signal inside buildings and outside of buildings. It happens at work and at home. It happens in Centarl London in the open air and inside. It happens in small towns.. It happens in the countryside. It happens in motor cars. It happens in airports. It happens when the battery is fully charged, when it is half charged and when it's low on charge. It happens using the phone, when reading messages and when using the internet.
Hope this helps.

How can I get my Mountain Lion more stable on the internet? It keeps losing the signal. Lion is solid as a rock on my other Macbook using the same router.

I downloaded Mountain Lion on my Macbook Air, and it works without a hitch except for internet connectivity. It keeps losing the signal. My Macbook using the same connection is solid as a rock and never loses the connection. Is there something I can do? Since my Macbook works weell under exactly the same conditions and if memory serves so did my Macbook Air with Lion before I downloaded Mountain Lion, none of the usual fixes seem to apply.
Applehank

I have the same problem, I think. I dont lose wifi signal, the mba stays connected to the router the whole time. Pings also seem unaffected by this problem. The problem is that web pages seem to load intermittently, in other words, it loads a page in 2 minutes. It loads:
the first 25% in the first 5 seconds
the next 25% in the next 50 seconds
the next 25% in the next 5 seconds
the last 25% in the last 50 seconds
Its quite annoying considering this can be as simple a page as goolge search results or even google.com.
I thought it was my ISP and i even made a big racket about it, switched ISPs and I have the same problem.
With the previous ISP I had a cisco router. This new ISP supplied their own modem/wifi. That doesnt seem to be the problem.
Im thinking its a config issue on my mba. I have the latest updates to ML.
Any ideas?

My 3gs (11 months old) has been losing all signal

my 3gs (11 months old) has been losing all signal for calls and both 3g/wifi, goes to "searching" then "no signal", and back to some signal but not for long at all. i upgraded to ios5 couple of wks ago but this was all happening before that, was hoping the upgrade would help, but noooooooooo! battery power has gone so bad in last few days too, charging up to 3 times a day!! cant afford a new phone so any help would be really appreciated.

A reset may help. Tap and hold the Home button and the On/Off buttons for approximately 10-15 seconds, until the Apple logo reappears. When the logo appears, release both buttons.
No content is affected by this procedure.

Freeview signal too low

Hi all,
Just moved home and have installed all put BT vision equipment only to get the dreaded "signal too low" message on screen. I checked our signal levels on the signal strength checker on the BT vision and every single channel seems to have 0 signal strength?! Does anyone think I have configured something wrongly? I have tried getting signal through our inbuilt freeview on the TV, again with no success.
We live in a very rural, hilly area with many trees.. Wondering if this is perhaps the problem?! Although I checked out postcode on the BT vision coverage checker and we were firmly included.
Any help greatly appreciated and I will give more info as needed!
Thank you

Thanks for reply. Have checked site and all transmitters seem good although not enormously close so reception limited? Have spoken to previous owner and they say freeview signal fine although they did not have a bt vision box and receives freeview through integrated tv. I have attempted to get signal through our integrated tv to no avail. Have now also tried other aerial sockets in the rest of the house, again to no avail. Beginning to wonder whether my aerial cable is incorrect as it wobbles somewhat in the wall sockets? It is a male pin to a female socket. Can't see how this could be the problem, but I'm running out of options!

E4200 - Losing Internet Signal

Trying to figure out our internet problem. Not sure if it's the ISP or router! Keep losing net signal. Thought it was the modem but last time I checked it & modem looked fine. Router light wasnt steady. It dropped twice after I rebooted both, and the router's light was flashing each time. ISP shows no drops from modem. We had a storm roll through Tuesday but there were no outages in my area & the router is plugged into a surge protector.It's an E4200.

If modem's internet connection is working fine then probably it's with the router. Are you experiencing the problem wired or wirelessly thru the router? If both then what I would suggest is that you change some settings on the router. For the wired connection, you try lowering down the mtu set on the router. For the wireless connection issue, you can change the wireless settings like changing the network name for the 5Ghz network and 2.4Ghz network, changing the channel and changing the wireless security. For the steps, you may refer to this link:
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=172c1dae41534ddd818c560b60c7c230_4029.xml&pid=80&r....

Losing power/signal and no internet connectivity for WRT54G2-RM

Just installed router and using Motorola SB5101 cable modem and Comcast. Followed instructions and the router has lost losing power and needing restarts a few times. Have it installed by ethernet cable to my desktop, and using laptop (XP Pro Thinkpad P42). Cannot get internet connectivity and also loses wireless signal connection. I know there are a number of similar posted issues, and I am new to this forum. Any ideas?

Download and upgrade your router's firmware, reset and then re-configure it...
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

Ipad losing Wifi Signal

Hi
My ipad is repeated losing it's Wifi signal. It is doing this at various locations, so I don't think it is a router issue.
I've tried Reset Network Settings and the problem persists.
Any suggestions?

Hi there,
I would recommend taking a look at troubleshooting found in the article below.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
-Griff W.

XOOM Losing 3G Signal

My XOOM was losing the 3G signal for the past two days (the entire time that I have had 3G data). I did a soft reset, per VZW tech support's advice. I used it for another 20 minutes or so and the signal stayed active. Has anyone else had this problem?
Also, video does not playback well on 3G, with lots of starts and stops. Any feedback is appreciated!

Yeah, I know what you mean. I lose my 3G connection, I reset it, it comes back then after awhile it goes away. What I think is the problem is that the Xoom is meant for 4G service cuz its quite a powerful device...I dunno...right now I'm having problems with my Xoom for being in "mirror mode" everything is reversed...taking it to Verizon in the morning to get it fixed

Keep losing wireless signal

My 9300 keeps losing its wireless signal. I phoned and was told to connect to a different network and then connect back to Vodafone which worked for a couple of days but I keep losing and going to GSM and then have to connect to a different network and back to Vodafone.

I assume you are running OS X 10.5.5. Try these simple maintenance routines:
Repair Permissions - /Applications/Utilities/Disk Utility.app. Start Disk Utility, select your HD and click on Repair Permissions. When finished, quit Disk Utility and then restart your computer.
Reset PRAM - hold down Option-Command-P-R keys when starting until you hear the startup chime a 2nd time.
Safe Mode Startup - hold down the Shift-key at startup until you see the login screen. When logged-in, then go to System Preferences/Network/AirPort, click on the 'Network Name:' roll-button, select 'Join Other Network...', enter 'Network Name and select the security type you are using, and finally, enter your Password and click 'Join'. Then, click the 'Apply' button and exit System Preferences.
How are you connected to the internet - DSL model > AEBn WAN port? Check your AEBn Internet setup. Open AirPort Utility, select your AEBn, Manual Setup, Internet - is 'Connection Sharing:' set to 'Off (Bridge Mode)' - set to this if not.
Now check System Preferences/Network/AirPort/ - click on 'Advanced', TCP/IP and confirm that 'Configure IPv4:' is set to 'Using DHCP'.
The above two paragraphs assume that your ISP uses a DHCP server to distribute IP addresses (normally the case).
Hope this helps.

A88X G45 Gaming losing display signal

I have just rebuilt my computer. I elected to go with the A88X G45 gaming motherboard with an AMD A10-5800K Trinity Quad Core 3.8 GHz. G. Skill Ripjaws X Series 8 GB DDR3 SDRam 2133(PC17000) (2x4 GB).
When I start the computer, I do not hear any beeps at all which I found interesting. I log into the BIOS and it recognizes everything installed and which ports are being used. I am using the onboard graphics card until I get everything set up and then I will add a separate GPU. After installing Windows 7, I log on to update the drivers before doing anything else. I have done this 2 times, once from the DVD provided with the board and once from a flash drive downloading the current ones off the msi website. After installing the chipset drivers and rebooting back into the Windows desktop, the monitor will go blank and state "no signal." This happens between 15 seconds and 5 minutes. I have tried the DVI, VGA, and HDMI ports on the board and get the same result with all of them.
The lights on the board stay on and the fans are still running. The reset button and power button do not do anything and the only way to power down is to turn off the power supply, which I hate to do. The LED table that displays codes does not show anything as if it is off. My mouse and keyboard similarly shut off.
I have tried checking the RAM, updating the BIOS, removing everything except RAM, CPU and PSU and still get the same result. I have 5 fans plugged in including the CPU fan.
I am really at a loss here and cannot figure out why I keep losing display connection and having the board essentially lock up. Any advice is greatly appreciated. First time forum user.
Thank you.

Quote from: Nichrome on 26-September-14, 05:27:07
Hi,
Please follow this >>Posting Guide<< in more detailed way (PSU, OS etc).
Also did you try clearing CMOS? >>Clear CMOS Guide<<
Also when this started to happen? As which parts are new and which old.
Main Board: MSI A88X G45 Gaming
Bios Version: v1.2
Video Card: On board
PSU: Corsair 750W
12v rail Rating of listed PSU: Unsure
CPU: AMD A10-5800K Trinity Quad Core 3.8 GHz
Memory: G. Skill Ripjaws X Series 8GB DDR3 2133(PC17000) (2x4GB)
SSD/ HDD: Samsung 840 EVO 120GB SSD
CPU COOLER: Stock cooler that came with CPU
Raid Card:
Sound Card: On board
Any Additional hardware plugged into your system: LG optical
OC: (Yes / No) NO
Operating System: Windows 7 Home 64 bit
I have tried clearing the CMOS with the button on board but have not tried taking out the battery. Everything that is currently installed is brand new (Board, CPU, RAM, Optical, SSD) with the exception of the PSU. I have had the PSU for a few years and have not had any issue with it on my old build. I was using my old build 3 days ago, got the board, CPU, RAM, Optical, and SSD all the same day and installed it. When I am on the BIOS screen, the display connection stays on and I do not have any issues. Similarly, I do not have any issues when I run Windows in Safe Mode. Only when I log into Windows normally will the screen go blank and lock up the board.

Nokia 5800 keeps losing wifi signal

When i connect to the internet, ovi store, google maps....anything that requires a connect on my nokia 5800 using my wi-fi it only stays connected for about 30-60 seconds then it says connection lost, it makes using wifi at home just impossible. There is nothing wrong with my internet as i conect to my modem with my ps3, psp and laptop and never ever lose signal. The signal strength on the nokia 5800 is over 80% and am never more then 10 feet away from modem but still constanly loses signal.....please help

I am also having the same problem I have to wireless routers in my house never had any problems before connecting to them but just this past week it my phone keeps losing connection and if I do a refresh it picks them up but once I try to connect. I get the messiah no wlan connections available.
Am thinking of contacting orange and asking for a replacement after all I do pay the £5 a month insurance.
Peter

IPhone losing all signal when put into sleep

When I put my iPhone 4 to sleep after about a minute all of my signal drops off and I'm unable to receive calls or messages until I wake it
When I wake it to signal indicator confirms what's happening and it displays either one bar or "no service." After about 10-15 seconds the signal strength jumps back up to full again and then i get all my voicemail and messages come through
It wasn't always doing this and has only been doing it for the last week or so
Anyone else having a similar issue?

I'm having similar issues, except when I wake the phone it still shows me full bars and 3G (or sometimes even wi-fi) connection, but I can't send or receive any calls or texts. I have to shut off the phone and turn it back on and then I end up with voice mail and texts that I missed. This even happens when I haven't put the phone into standby - I can be using an app and then go to text someone or make a call and find out it's all jacked up. It's annoying because I never know if/when I need to restart the phone.

MacBook Pro 15" losing HDMI signal intermittently

MacBook Pro 15" Late 2011 (Mavericks 10.9.4); 4 GB ram. I am running HDMI to a new video projector. The HDMI signal is lost periodically for about 1-2 seconds and then comes back. It occurs about every 5-7 minutes (about 20 times during a 50 minute lecture). It loses both video and audio. Screen goes black but no displayed messages. I have read a variety of other posts with similar symptoms with various computers (e.g. Mac mini) and even with DVI cable use. In my case, I've used two different HDMI adaptors so it's not the adaptor. I'm pretty sure it's not the HDMI cable itself. (A fellow professor does not have the issue with his PC and he uses the same equipment.) Neither the computer nor the cable is touched. (I have another colleague who reports the same symptoms in his music lab.) Bottom line is that it's a distraction to my students and it's occurring off different Macs in different locations. This means to me that it may be something with the particular generation of Macs we're using. Looking for help to resolve the issue.

Assuming this is your machine - MacBook Pro (15-inch, Late 2011) - Technical Specifications you are using a DisplayPort (from the Thunderbolt/DP port) to an HDMI adapter. Non-Apple adapters have issues.
The other factor is that there are GPU issues with the AMD - problems with amd gpu on early 2011 macbook pro (there are many threads like this).
Either issue may be impacting your Mac connectivity. The third-party adapters may not be able to drive signals consistently.
Can you test with an Apple-branded DP-to-HDMI adapter and the 50' cable?

Freeview signal poor quality or too low level

Yesterday I tried to order a new YouView box to replace my Silver Vision box. Hopefully it will arrive soon.
Meanwhile I switched my box on for the first time for a few days and was met with the message in the heading.
That's rather strange as I have my TV connected via the Vision box and the TV reports a very good signal level. I have tried powering down and also what I understand to be the factory reset all with no improvement.
Has anyone else experienced this or got an answer to it?

Hi VLT,
Thanks for posting. Are you still having problems? Take a look here for help with free view issues.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

Losing freeview signal

Similar Messages

Maybe you are looking for