Loss of connectivity of a wireless network when more than one laptop connects to the internet.

Hi,  I have a wired network of 20 computers controlled by a net gear wired router from a DSL modem. The router is plugged into a hub. I have a linksys router WRT54GX4 which is plugged into the hub to allow wireless internet access. The DHCP has been disabled on the wireless router. I have added three access points WAP54G which are plugged into the wired network in outer rooms to expand the wireless network. The wireless network works just fine with only one laptop connected to the internet but when two laptops connect they both lose connectivity. That is my problem. Does anyone have any suggestions? The IP address of the wired router is 192.168.2.1, the IP address of the wireless router is 192.168.2.3, the IP address of the access points are 192.168.2.245, 192.168.2.246, 192.168.2.247. All the devices are on channel 11. All have the same SSID. The default gateway on the access points is 192.168.2.1. It is an unsecured network. Please help.  Thanks   Peter Z

Hi MnM Show,
Tim is correct, if you are using ISCSI Storage and using the network to get to it, it is recommended that the iSCSI Storage fabric have a dedicated and isolated network. This
network should be disabled for Cluster communications so that the network is dedicated to only storage related traffic.
This prevents intra-cluster communication as well as CSV traffic from flowing over same network. During the creation of the Cluster, ISCSI traffic will be detected and the network
will be disabled from Cluster use. This network should set to lowest in the binding order.
The related article:
Configuring Windows Failover Cluster Networks
http://blogs.technet.com/b/askcore/archive/2014/02/20/configuring-windows-failover-cluster-networks.aspx
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Similar Messages

  • How to allow access to my airport extreme network for more than one wirelss device at the same time

    I received a Kobo Vox ereader for Christmas and have not been able to connect to my home wireless network. It works with unsecured networks and I tested it out at an Apple reseller with their airport extreme netwok and it connects fine.
    It seems as if I cannot have more than one wireless device connected to my home netork at the same time.
    So here is what I did to test this out:
    - I powered off the Kobo vox
    - I shut down my macbook
    - I turned off the modem and unplugged the power cord and removed the cable connection from the modem.
    -  I also unplugged the airport extreme router.
    - I waited for about 15 minutes and then set it all up again and turned on the power to the router and the modem
    - I turned on the kobo  vox (I left my laptop shut down)
    - my kobo vox was able to connected to the internet.
    - I powered up my laptop and it couldn't connect to the internet.
    So, I went through the above steps again and powered up my laptop first and was able to connect to the internet. I then turned on my Kobo and was not able to connect.
    It seems as if I can only have one device connected to my wireless network at one time and that device is the first one to be powered on and connected to the internet.
    Am I missing some network or airport extreme settings...
    thanks

    Try the following on your Mac.....
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click Manual Setup
    Click the Internet icon
    Click the Internet Connection tab
    Change the setting for Connection Sharing to read Share a public IP address
    Click Update

  • I have a macbook and its hooked up to my airport express, however, I have a 5 year old dell pc that is connected to my wireless network, yet i'm unable to get on the internet with the pc.   Does something need to be adjusted on the pc?

    I have a macbook and its hooked into my airport express.  I get on the internet through my network with no problem.  Now I have a pc that says its connected to my network through airport express, yet I can't get on the internet with it - its around 5 years old with Windows XP.  What should be adjusted on the pc ?

    I have a macbook and its hooked into my airport express.  I get on the internet through my network with no problem.  Now I have a pc that says its connected to my network through airport express, yet I can't get on the internet with it - its around 5 years old with Windows XP.  What should be adjusted on the pc ?

  • Can I change which nic is used for a cluster network when more than one nic on the node is on same subnet?

    This cluster has been up and working for maybe a year and a half the way it is.  There are two nodes, running Server 2012.  In addition to a couple network interfaces devoted to VM traffic each node has:
    Management Interface: 192.168.1.0/24
    iSCSI Interface: 192.168.1.0/24
    Internal Cluster Interface: 192.168.99.0/24
    The iSCSI interfaces have to be on same subnet as management interfaces due to limitations in the shared storage.  Basically if I segregate it I wouldn't be able access the shared storage itself for any kind of management or maintenance tasks. 
    I have restricted the iSCSI traffic to only use the one interface on each cluster node but I noticed that one of the cluster networks is connecting the management interface on one cluster node member with the iSCSI interface on the other cluster node member. 
    I would like for the cluster network to be using the management interface on both cluster node members so as not to interfere with iSCSI traffic.  Can I change this?
    Binding order of interfaces is the same on both boxes but maybe I did that after I created the cluster, not sure. 

    Hi MnM Show,
    Tim is correct, if you are using ISCSI Storage and using the network to get to it, it is recommended that the iSCSI Storage fabric have a dedicated and isolated network. This
    network should be disabled for Cluster communications so that the network is dedicated to only storage related traffic.
    This prevents intra-cluster communication as well as CSV traffic from flowing over same network. During the creation of the Cluster, ISCSI traffic will be detected and the network
    will be disabled from Cluster use. This network should set to lowest in the binding order.
    The related article:
    Configuring Windows Failover Cluster Networks
    http://blogs.technet.com/b/askcore/archive/2014/02/20/configuring-windows-failover-cluster-networks.aspx
    I’m glad to be of help to you!
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Multiple select queries used in Excel BI report ,fetching data from Sharepoint DB(SP2010_Prod_ProjectServer) causing blockage on DB ,when more than one workbook(same copy of Excel BI Report) refreshed using Refresh All option.

    I am using mutiple select queries to fetch data from Project Server 2010 DB(its sharepoint DB) and these queries fetch data in Excel BI report by establishing connection with DB using instance name and all. I have enhance all these select queries and data
    is being fetched in secs. but when more than one copy of same Excel BI report is refreshed using 'Refresh All' option, then these select queries cause blockage on DB.
    Please let me know mitigation for this blockage issue.
    Should I use begin transaction and commit transaction statements/ shared lock statements.
    please reply

    Hi,
    run same query at the same time?

  • I need to connect my iPad to a projector and USB ports. What do I need to do this and where can I get the suitable fittings? I really need to have more than one USB connection port. Help

    I need to connect my iPad to a projector and have USB ports. What do I need to do this and where can I get the suitable fittings? I really need to have more than one USB connection port. Help

    You can connect via a cable or wireless using an Apple TV.
    http://ipad.about.com/od/iPad_Guide/a/How-To-Connect-Your-Ipad-To-Your-Tv.htm
    Connect an iPad to a Television or Projector
    http://www.everymac.com/systems/apple/ipad/ipad-faq/how-to-connect-ipad-to-tv-te levision-projector.html
    Connecting iPad iPhone or iPod to TV or Projector
    http://www.disabled-world.com/assistivedevices/computer/ipad-tv.php
    iPad Accessories: Connections for a TV or Projector
    http://www.dummies.com/how-to/content/ipad-accessories-connections-for-a-tv-or-p rojector.html
    You may be interested in AirPlay on the Apple TV:
    http://www.apple.com/airplay/
    Alternately, there are Apple Digital AV Adapters for hardwired connections:
    http://support.apple.com/kb/ht4108
    If your location does’t have wifi to use with the Apple TV, use a portable router.
    Portable routers http://compnetworking.about.com/od/routers/tp/travel_routers.htm
     Cheers, Tom

  • HT4437 is there a way to connect my ipad with airplay to more than one airplay enabled speaker? at the moment it allows me to connect to only one?

    is there a way to connect my ipad using airplay to more than one airplay enabled speaker?  when i tap the airplay icon on my ipad i see the list of all the speakers in each room but i can only connect to one at a time. Itunes, on my laptop, allows me to connec to all of them at the same time but Music on my ipad allows me to choose only one speaker at a time. Can several be connected at the same time using Music on Ipad or iphone?

    That's great, but not what we want to do. I've been looking at all the boards for a solution to this and, you are correct. There isn't one - at least not one native to iOS. What I think EricB2 would like, as well as many of us, is the ability to take any audio stream (pandora, tune-in radio, etc.) and stream directly to multiple airplay devices from our iPads and iPhones without having to use the computer. Just walk into the house from the car, hit a button on the iDevice and start listening to the same stream we were listening to in the car on all of our home speakers. I know, this is like science fiction.  My own opinion is that it would cut into Apples lucrative iTunes business model and really isn't in their best interest, so I don't think it will be happening anytime soon. Bottom line is if you want to use your Apple devices for whole house streaming, you need a computer and music from iTunes($$). Otherwise it's $$ out of Apples pocket.

  • More than one device connected?

    I am testing out a project for a mobile device and  when I package the apk and attempt to launch it on my phone, I get an error message sying that it can't be done because I have more than one device connected. I only have one device connected.
    I've tested this project before n my phone and it launched as it was supposed to, but I added a document class to the project and think that might be causing the problem. Previously, I added all of my action script to a keyframe on the timeline, and everything worked fine.
    I'd like some feedback as to whether or no the document class issue is the likely problem and how to get around it. If that's not the problem, I'd like to what what might be going on. As always, any help is greatly appreciated. Thanks.

    using a document class is not the problem (though your document class may be a problem if it has errors).
    use a file explorer to see if your computer lists more than 1 connected device.  or restart your computer to reset its external connections.

  • Can I use more than one database connections in a jdeveloper project?

    I use jdeveloper version 9.0.4.0 (build 1407),Can I use more than one database connections in one jdeveloper project?

    9.0.4 is a fairly old version, so you may only find a few people who know how it worked.
    Assuming you're using ADF BC, once known as BC4J, once know as JBO, in the project, and that the architecture hasn't changed much, then the answer is only 1 connection per project.
    Programmatically you're free to use as many connections via JEE as you see fit, but ADF BC is limited to one connection.
    CM.

  • Can more than one laptop use a wireless network at a time?

    Hi...quick question and this may be a stupid one .. but a few months ago my uncle was living with us and had a laptop which had a wireless Internet connection. I had already had my Ibook set up and was using a wireless Internet connection. When he turned on his mine stopped working? Why was that happening? Also ... my dad is buying my mom a laptop for Xmas and I'm sure that it will have a wireless connection as well? I'm hoping that same thing will not happen again. Why would the wireless router only read one laptop in the same house? Aren't wireless routers suppose to read more than one computer? I just don't want my MAC to be unable to use the Internet once another laptop is in our house. Does anyone have any suggestions? Thanks a ton!
    IBook   Mac OS X (10.4.8)  
    IBook   Mac OS X (10.4.8)  

    Karen, welcome to the discussions.
    Using a wireless router will enable you to connect upwards of 50 computers all at the same time and simultaniously.
    Take care to read the set up procedure for the particular Wireless Router you are using for your Network.
    There are several different ways to confiqure a wireless Network.
    AS long as all of the computers you have, do in fact have wireless cards in them you shouldn't have a problem.
    There is a difference in the set up for PC and a Mac.
    There is also a difference in Wireless Routers and there capabilitys, some are for older wireless 802.11b compliant systems. Whereas the newer Routers or Base stations are for both older 802.11b and the newer 802.11g connections.
    They will say 802.11b/g or something close.
    Most will require you connect your Internet Service Providers Modem to the WAN Port of your choice of Wireless Router. Like I said follow the directions.
    Good Luck
    Don

  • Use of layout when more than one parameter - Error Missing Parameter Values

    Hi,
    Is it possible to use a crystal report which has more than one parameter as the layout for the bill of materials report.
    I have 3 parameters
           1. DocKey@       The Bill of Materials to be printed
           2. Number of levels to be printed
           3. type of levels to print.
    When I try to print it gives me the error Missing Parameter Values.
    I have tried changing the DocKey@ to CodeKey@ but the same error.
    Does anyone now where to find a list of these tokens?
    Thanks
    Chris

    I looked at the crystal report conversion to try to find what parameters it used and found none.
    I have managed to create and use a crystal report to replace the production order using DocKey@ as the parameter.  This works within SAP.  However I have converted the system production order to crystal reports and from the converted report I cannot see any parameters at all.
    How and where can you find out what paramters you need to use to replace any PLD report?  Several reports have multiple selection criteria before the report prints.  How can you find out what their tokens are called?  I am starting to pull my hair out.  I am getting great help from this forum, but do you know any documentation which actually explains this area.
    Thanks
    Chris

  • [JS CS3] Need an array of paragraphs when more than one story

    Hello,
    If I have a document with only one story the following line returns an array of all the paragraphs. I can then iterate through the array to my hearts conent.
    var paraRef = app.activeDocument.stories.everyItem().paragraphs;
    However, if there is more than one story, then, according to the Data Browser, some of the object Paragraphs contain more than one paragraph and some of the object Paragraphs are invalid. The length of paraRef is correct, i.e. it equals the total number of paragraphs in the document, but each member of this array either  "bunched up" or contains nothing.
    How can I write this so that  when I have more than one story I can get an array of all the paragraphs?
    Thanks,
    Tom

    Thanks, Harbs and Dave!
    Before I saw your answers I came up with a (longer) solution:
    var storyRef = app.activeDocument.stories;
    var arrStories = [];
    for(var j = 0; storyRef.length > j; j++){
        arrStories.push(storyRef[j])
        }//end for
    var arrParas2 = [];
    for(var x = 0; arrStories.length > x; x++){
        for(var y = 0; arrStories[x].paragraphs.length > y; y++){
            arrParas2.push(arrStories[x].paragraphs[y]);
            }//end for y
        }//end for x
    But I am curious about something. Your solution and my solution both result in an array of all paragraphs in the document but the data browser shows these arrays in different ways. I am wondering how to intrepret them.
    Your solution does not show the indexed paragraphs, mine does. See the images below.
    Your solution:
    My solution:

  • The file is not readable, when more than one file open

    Get this error when I try to open more than one file. Happens on different files, but especially on jobs that have side panels on packaging. The files have placed .psd images. Happens on different computers (10.6 & 10.8.2).
    Can get the file open usually by closing the othere open file, but then is hard to copy and paste between files. Sometimes I get this when trying to open one file, but restarting Illustrator usually fixes this.
    Have tried working directly from the hard drive, and still get this problem. Does to follow an exact pattern, can try to open file a, then b one day thsi will work another will fail. Seems like something is corrupting the memory, and usually happens with more complex files. Happens in CS5 & CS6, though I mostly work in CS5.

    Anyone else getting this error?

  • Macbook freezing when more than one program runs

    Hello all,
    My Macbook is about a year and a half old. A few weeks ago, it crashed catastrophically, and the geniuses at my local store replaced the logic board.
    Since getting it back, it's been crashing almost every time I try to run more than one program, such as itunes and safari. Ichat video or photobooth on their own cause it to freeze. The freezing process is gradual; first the program I'm looking at freezes, but I can navigate to other programs, but within a few minutes those freeze as well. During the freeze, the cursor moves (in beachball shape) but the screen is unresponsive and apple-option-escape has no effect; the only solution is to manually turn it off. It's also taking longer and longer to boot up. This happens when it's plugged in as well as on battery power. It's gotten to the point that I'm scared to do work on it, because I can't trust it to work long enough to save my data. What happened? Is this the result of my "fixed" logic board or something else? I am getting SO FRUSTRATED by how unreliable my macbook has become!!

    To rule out any 3rd part apps/additions are causing the problem, try booting into Safe Mode...
    http://docs.info.apple.com/article.html?artnum=107392
    Have you replaced/changed Ram lately? ...if so, try reverting back to the old.
    You could also ensure you've run your standard Maint. scripts (via Onyx, Cocktail etc...) and perhaps boot to the Install DVD to verify/repair the hard drive and its permissions. Booting to the Install DVD and running the Apple Hardware Test (hold 'D' on startup) could also reveal things.
    Failing all that, try resetting the SMC and Pram...
    http://docs.info.apple.com/article.html?artnum=303319
    http://docs.info.apple.com/article.html?artnum=2238
    To rule out a 'bad' hard drive you could either replace it physically or try booting from another Macbook via firewire...
    http://docs.info.apple.com/article.html?artnum=58583
    These are all a bunch of general procedures that the user can try to eliminate the issues - if nothing works, you'll need to make another trip to the genius bar.

  • HP 3050 will not stay on the wireless network for more than a few minutes at a time.

    My HP DeskJet 3050 J610 is constantly dropping the wireless connection. It won't stay on for more than a few minutes. If I power cycle, it comes right back on, but drops again after a few minutes. It will print fine from a USB. When it drops off, pings time out even though the device shows "ready" in Windows 7, Windows XP and OSX. I've done everything HP suggests - static IP, upgraded firmware, diagnostic tools, etc. I am out of options.
    I can hit print right now, printer shows as ready, then I will get a print error. If I go over and power cycle the printer, my document will print - most of the time. It will remain on the network for a few minutes, then stop working. As soon as I power cycle it, I get a few more minutes before it drops. It has always done this from day one.

    I don't have another wireless network close by that I could test it on. I'm a little isolated. i might be able to work out a time when I could take it by a friend's house, but he's over an hour away.
    I have a Win 7 laptop, a Win XP desktop and an old Mac Powerbook as well as an iPod Touch and iPad 3 that use my wireless network without any problems - besides the fact that hardly any of my devices will talk to the other... But that's an OS issue. They all see the network, and the printer after I cycle the power on it.
    My wireless router is a Netgear WNR2000. I remember monkeying with the channels when I frist got this printer a few months ago, but I don't remember what all I did. Since I did a firmware update on the router, the channel is now set to Auto. If there's a channel you think I should try, let me know what it is. The printer shows up on the list of devices in the router, but that may be because I have its address reserved for the static IP. Interestingly, the router sees the printer, even though my devices cannot. I did a ping just now while checking that, and got this - which is unusual. Normally they all time out.
    Pinging 192.168.1.150 with 32 bytes of data:
    Request timed out.
    Request timed out.
    Reply from 192.168.1.150: bytes=32 time=3223ms TTL=255
    Request timed out.
    Ping statistics for 192.168.1.150:
        Packets: Sent = 4, Received = 1, Lost = 3 (75% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 3223ms, Maximum = 3223ms, Average = 3223ms
    Played around a bit more pinging between devices and got this oddity - without a power cycle just a couple minutes later.
    ping 192.168.1.150 -n 50 -l 500
    Pinging 192.168.1.150 with 500 bytes of data:
    Reply from 192.168.1.150: bytes=500 time=527ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=12ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=21ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=17ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=13ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=21ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=15ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=11ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=10ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=22ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=19ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=22ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=18ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=16ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=14ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=9ms TTL=255
    Reply from 192.168.1.150: bytes=500 time=20ms TTL=255
    Ping statistics for 192.168.1.150:
        Packets: Sent = 50, Received = 50, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
        Minimum = 9ms, Maximum = 527ms, Average = 26ms
    Is there a possibility that the printer is going into a standby state and having trouble waking when traffic hits? I don't know if that's possible, just seems like it looking at this.

Maybe you are looking for

  • Error: File just captured could not be read and was deleted after capture.

    I was just recording an extremely important interview. I have recorded literally 10.000 recordings before with the same setup, every day, over a period of some three years now. I'm recorging DV PAL through SDI input on a AJA KONA LS card. It seemed t

  • I want to share my Ical with a google calendar user- how can I do that?

    I have tried sharing it, by sending them an e-mail invite- however that just ask them to sign up for icloud. I tried making it public and sending them the URL, they got a robots can't read the txt (or something like that) message. Any other suggestio

  • Address book in piserverdb tree

    Hello if my knowledge is correct, the address book is stored in the o=piservdb tree in the Directory server. but how is that data stored? because when I export an ldif of o=piservdb tree and i look for a certain user which i know has nearly 2000 cont

  • What is mean by Referential Integrity? Where do we use it and Why..?

    Hi All, Can anybody tell me, What is mean by Referential Integrity? Where do we use it and Why..? Regards, Kiran Telkar

  • IPhone 3g 16gb back housing needed

    Hi, i have an iPhone 3G 16gb that i want to sell, but because of a small 5mm long hairline crack in the back of the phone most recycling sites online will only offer me the minimum amount for it- stupid really because the rest of the phone is perfect