Loss of FN-Keys after installation of Microsoft security updates on L500

I'm using a satellite L500-19U
After installation of Microsoft security updates the FN keys lost their functin except the Brightness + / - function.
also the soft keys which appear at the upper monitor border by pressing the FN key didn't appear after the security packages were installed.
I solved The problem by removing the update by means of the roll-back function (Wiederherstellungs punkt) of W7.
The following security packages are selected to be installed:
Security update for Windows 7 for x64-based Systems (KB978601)
Security update for Windows 7 for x64-based Systems (KB979309)
Security update for Windows 7 for x64-based Systems (KB979683)
Security update for Windows 7 for x64-based Systems (KB980232)
Security update for Windows 7 for x64-based Systems (KB981332)
Windows MRT x64 - April 2010 (KB890830) (malicoius software removal tool)
Which of them are unsuspicios, which shall be posponed, which updates are necessary after installation of the updates?
Message was edited by: JoJo58

hi,
If you read about these update on the Microsoft site: (Non of them should influence on FN-Keys)
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=998164b7-4b8c-468b-8d39-f242633c8838
I have checked the history of updates on my computer and all of them are installed except for Windows MRT x64 - April 2010 (KB890830) (malicoius software removal tool). Everything works fine, try to remove this update.

Similar Messages

I received a pop up regarding security certificates when opening a PDF document today. Is it safe to say "yes" to the installation of the security updates?

I received a pop up regarding security certificates when opening a PDF document today. Is it safe to say "yes" to the installation of the security updates?

If you opened it with Adobe Reader, then yes: "Yes" is safe (I just did the same thing one minute ago).

Each time my iMac reboots i am prompted to enter my FaceTime password. This just started occurring after the most recent security update.

Each time my iMac reboots I am prompted to enter my FaceTime password. This just started occurring after the most recent security update. When I put my password in the pop up just comes back, if I press cancle it goes away. Any ideas on how to get rid of this annoying popup?

I had the same problem. Try this. Launch FaceTime. Click the toggle to turn it off; or Command-K. Quit. Do a restart, you shouldn't get the popup. You could then turn FaceTime back on if you wish. Either way, the popup should be gone from then on.

Cannot download adobe flash even after i disable microsoft security essentials. what do you suggest???

i just got an hp p7 q7 quad desktop. i'm having great difficulty downloading adobe flash player apparently because i'm using firefox as my browser. i disabled microsoft security essentials as instructed, but i'm still unable to download.
any suggestions???

I suggest that you download and run the Acrobat Cleaner Tool http://labs.adobe.com/downloads/acrobatcleaner.html
Next download and run the offline installer from http://get.adobe.com/reader/enterprise/ - all availabel Reader versions 9.5, 10.1, and 11.0 should run fine on Windows XP.
[topic moved to Adobe Reader forum]

Problems after installation 16.0.3 update for Windows

I propose here to report problems appeared after installation 16.0.3 Illustrator update for Windows.
As for me:
Don’t display Stray and Center Points in Outline mode;
Eyedropper+Shift works incorrectly;
Graphic Style Libraries -> Additive make disappeared Fill.

Hi K,
Thank you for you reply and sorry if the information was a bit too truncated. well here goes.
I am using a MacBook Pro (3.1) 17 inch, 2.4GHz processor, 2 GB ram. I edit video using Final Cut Studio 2. i am having a problem with Final Cut Pro 6 after downloading the latest update (6.0.3). Before I downloaded the update I used to be able to export my movies on the Quicktime option of FCP (not compressor or Quicktime conversion) giving me the option to view the the movie while in an FCP Project. The viewer used to scale the exported video to 16.9 (720 by 576 anamorphic), it no longer does this, instead playing it in 4.3. I have tried exporting both from the time line and the canvas but the viewer will only preview in 4.3. As I want to see it in 16.9 because that is what the movie was made in, captured and edited in. The original settings have not changed but there seems to be this annoying problem.
I hope that is enough detail
Ivan

IE unexpectedly exits after installation of MS security patch KB918899

We installed Microsoft security patch KB918899 (MS06-042) on W2K Clients (IE6 SP1) and found that afterwards IE terminates unexpectedly when trying to access our local EP6 or sdn.
Meanwhile Microsoft describes this problem in KB923762
http://support.microsoft.com/kb/923762/en-us and delivers a hotfix via Microsoft Product Support Services.

We installed Microsoft security patch KB918899 (MS06-042) on W2K Clients (IE6 SP1) and found that afterwards IE terminates unexpectedly when trying to access our local EP6 or sdn.
Meanwhile Microsoft describes this problem in KB923762
http://support.microsoft.com/kb/923762/en-us and delivers a hotfix via Microsoft Product Support Services.

Mac Mini won't boot after applying 2009-001 Security Update

I'm stuck at the gray startup screen with the Apple logo and the "gear wheel" progress indicator. Still stuck there after 60 minutes of "letting it brood."
How to I fix this?

The easiest way to solve the problem is to restore the drive from the backup you made just before installing any update or software on your computer, then do the installation again following the suggestions at the end of this post. Failing that...
First, try the routine repair disk and repair permissions with Disk Utility on your installer disc. Boot from the installer disk, select language if applicable, choose utilities, run Disk Utility and verify (and repair if necessary) the drive. You can verify a drive from DU on your main drive while booted but I have found this can result in incorrect reporting of errors. To repair your drive you have to run it from a drive other than the boot drive anyway.
Next, boot from your drive in [Safe Mode|http://docs.info.apple.com/article.html?artnum=107393] and repair permissions. You can repair permissions while booted from the installer disc but this uses the permissions configuration on the installer disc which may be out of date if you have run any updates on your computer. Booting your computer to Safe Mode restricts the number of things running on your computer while permissions are being run and done a bit of spring cleaning at the same time.
[Resolve startup issues and perform disk maintenance with Disk Utility and fsck|http://docs.info.apple.com/article.html?artnum=106214]
[Using Disk Utility in Mac OS X 10.4.3 or later|http://docs.info.apple.com/article.html?artnum=302672]
[Disk Utility's Repair Disk Permissions|http://docs.info.apple.com/article.html?artnum=25751]
From BDaqua (couldn't have said it better):
"Try Disk Utility
1. Insert the Mac OS X Install disc that came with your computer (Edit: Do not use this disc if it is not the same general version as what you have currently on your computer, e.g. use a Tiger disc for a Tiger drive, not a Panther disc), then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
Then Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes."
If you don't have an installer disc available you can try effecting repairs using [fsk in Single User Mode|http://docs.info.apple.com/article.html?artnum=106214].
[Post by japamac about using fsk|http://discussions.apple.com/thread.jspa?threadID=1649143&tstart=0]
If the above don't work, two things seemed to be solutions for Security Update 2008-008 problems.
One is Archive and Install which will replace the corrupted system but then requires you reapply all your updates. Select the keep settings and preferences when doing A&I. Make sure you select that option when doing A&I if you want settings and preferences kept. Some third party applications may need reinstalling if they have special components.
[Mac OS X: About the Archive and Install feature|http://support.apple.com/kb/HT1710?viewlocale=en_US]
[X-Lab Archive and install|http://www.thexlab.com/faqs/archiveinstall.html]
[Kappy's A&I instructions|http://discussions.apple.com/thread.jspa?threadID=1823034&tstart=0 ]
[How to get files from a previous home directory after Archive and Install|http://docs.info.apple.com/article.html?artnum=107297]
The other is to try to re-install the security update on the main drive while booted from a secondary drive or in Single User Mode. This could be from another Mac computer while your first one is in Target Disk Mode, perhaps a bootable backup drive, or possibly from your installer disc. Here's references for those methods:
http://discussions.apple.com/message.jspa?messageID=8728797#8728797
http://discussions.apple.com/message.jspa?messageID=8733921#8733921
http://discussions.apple.com/thread.jspa?messageID=8634535#8634535
Updating
There's been recent discussions as to what steps are truly necessary in doing a minimal problem update.
I think #1 to which all agree is to make sure you have a backup of your computer in case you do need to back out of it again.
Some like to boot from their installer discs or an external backup and verify (and if necessary repair) their internal drives as well as drive permissions. This is done with Disk Utility. You can verify a drive while booted from the same drive but sometimes this produces spurious errors. Repairing a drive (if necessary) has to be done while booted from another disk. Permissions repair can, and is probably best, done when booted from your internal drive.
[Resolve startup issues and perform disk maintenance with Disk Utility and fsck|http://docs.info.apple.com/article.html?artnum=106214]
[Using Disk Utility in Mac OS X 10.4.3 or later|http://docs.info.apple.com/article.html?artnum=302672]
[Disk Utility's Repair Disk Permissions|http://docs.info.apple.com/article.html?artnum=25751]
You can also go to the step of booting into safe mode to do the install.
[Mac OS X: Starting up in Safe Mode|http://docs.info.apple.com/article.html?artnum=107393]
[What is Safe Boot, Safe Mode? (Mac OS X)|http://docs.info.apple.com/article.html?artnum=107392]
[Safe Boot takes longer than normal startup|http://docs.info.apple.com/article.html?artnum=107394]
I like to download the update onto my computer and install it from there rather than let Software Update do it. I know a few people who had problems with doing the update via software updater found a manual install to work.
Repair permissions again afterward.
It also helps to only install one update at a time and to run the computer for a while to make sure it is behaving well.
Almost all of the above steps (except backup) have been questioned as to necessity because probably many people have done successful updates without doing them. I say they can't hurt, they can very likely do good (especially if your computer isn't regularly maintained), so why not do them to be safe.
[BDaqua's comments on updating problems|http://discussions.apple.com/message.jspa?messageID=8948595#8948595]

IMac G5 freezes on start up after ITunes, Quicktime and Security update

On June 2nd, the following event occurred on my IMac G5 (model year 2005) equipped Mac OS 10.4.9
Upon completion of the automatic update for Itunes, Quicktime and a security update, the computer restarted.
However, the start-up sequence freezes on a grey screen with the logo for the power button displayed in the middle and a message inviting to hold down the poer button down for 5 sec to re-start.
the only way to complete the start up sequence is to hold down the apple key while pressing the power button.
Does anyone have any suggestions to regain control of my computer ?thank you in advance.

Welcome to Discussions - Hopefully, you repaired permissions both before and after updating, if not, it might be a good thing to do now. Also, you are not alone in having problems with the update, take a look at this.
Generally, it's better to install updates one by one, so that if you have problems, you know which one caused them.
Miriam

Issues With Microsoft Security Update Q2855844

On every one of our Windows 2008 Standard Edition 32-bit servers the Q2855844 update errors out during the installation. Is anyone else having an issue with this update? This is what is in the WindowsUpdate log:
2014-08-06 09:04:07:171 3612 e40 Misc =========== Logging initialized (build: 7.0.6002.18005, tz: -0400) ===========
2014-08-06 09:04:07:171 3612 e40 Misc   = Process: C:\Windows\system32\wusa.exe
2014-08-06 09:04:07:171 3612 e40 Misc   = Module: C:\Windows\system32\wuapi.dll
2014-08-06 09:04:07:156 3612 e40 COMAPI ----------- COMAPI: IUpdateServiceManager::AddScanPackageService -----------
2014-08-06 09:04:07:171 3612 e40 COMAPI   - ServiceName = Windows Update Standalone Installer
2014-08-06 09:04:07:171 3612 e40 COMAPI   - ScanFileLocation = C:\3e436a1d0e597e7d7fb1ed77f33df5\wsusscan.cab
2014-08-06 09:04:07:187 1004 908 Misc Validating signature for C:\Windows\SoftwareDistribution\ScanFile\91e7e2cd-c456-4147-ac0f-a4a217628611\Source.cab:
2014-08-06 09:04:07:218 1004 908 Misc Microsoft signed: Yes
2014-08-06 09:04:07:374 1004 908 DtaStor Default service for AU is {9482F4B4-E343-43B6-B170-9A65BC822C77}
2014-08-06 09:04:07:374 3612 e40 COMAPI   - Added scan package service, ServiceID = {91E7E2CD-C456-4147-AC0F-A4A217628611}
2014-08-06 09:04:07:374 3612 e40 COMAPI -------------
2014-08-06 09:04:07:374 3612 e40 COMAPI -- START -- COMAPI: Search [ClientId = wusa]
2014-08-06 09:04:07:374 3612 e40 COMAPI ---------
2014-08-06 09:04:07:405 3612 e40 COMAPI <<-- SUBMITTED -- COMAPI: Search [ClientId = wusa]
2014-08-06 09:04:07:405 1004 b10 Agent *************
2014-08-06 09:04:07:405 1004 b10 Agent ** START ** Agent: Finding updates [CallerId = wusa]
2014-08-06 09:04:07:405 1004 b10 Agent *********
2014-08-06 09:04:07:405 1004 b10 Agent   * Online = Yes; Ignore download priority = No
2014-08-06 09:04:07:405 1004 b10 Agent   * Criteria = "IsInstalled=0"
2014-08-06 09:04:07:405 1004 b10 Agent   * ServiceID = {91E7E2CD-C456-4147-AC0F-A4A217628611}
2014-08-06 09:04:07:624 1004 b10 PT +++++++++++ PT: Synchronizing server updates +++++++++++
2014-08-06 09:04:07:624 1004 b10 PT   + Offline serviceId = {91E7E2CD-C456-4147-AC0F-A4A217628611}
2014-08-06 09:04:07:624 1004 b10 PT WARNING: Cached cookie has expired or new PID is available
2014-08-06 09:04:11:617 1004 b10 PT +++++++++++ PT: Synchronizing extended update info +++++++++++
2014-08-06 09:04:11:617 1004 b10 PT   + Offline serviceId = {91E7E2CD-C456-4147-AC0F-A4A217628611}
2014-08-06 09:04:11:758 1004 b10 Agent   * Added update {DDD48962-1B38-478A-91B4-5DF779748AF7}.501 to search result
2014-08-06 09:04:11:758 1004 b10 Agent   * Found 1 updates and 54 categories in search; evaluated appl. rules of 271 out of 284 deployed entities
2014-08-06 09:04:11:820 1004 b10 Agent *********
2014-08-06 09:04:11:820 1004 b10 Agent ** END ** Agent: Finding updates [CallerId = wusa]
2014-08-06 09:04:11:820 1004 b10 Agent *************
2014-08-06 09:04:11:820 3612 d68 COMAPI >>-- RESUMED -- COMAPI: Search [ClientId = wusa]
2014-08-06 09:04:11:820 3612 d68 COMAPI   - Updates found = 1
2014-08-06 09:04:11:820 3612 d68 COMAPI ---------
2014-08-06 09:04:11:820 3612 d68 COMAPI -- END -- COMAPI: Search [ClientId = wusa]
2014-08-06 09:04:11:820 3612 d68 COMAPI -------------
2014-08-06 09:04:15:783 1004 908 DnldMgr *********** DnldMgr: Copy update to cache [UpdateId = {1941692E-A102-4EA0-804E-76906EDC3E82}.501] ***********
2014-08-06 09:04:15:783 1004 908 DnldMgr Asking handler to generate non-range requests.
2014-08-06 09:04:15:798 1004 908 Handler Generating request for CBS update 1941692E-A102-4EA0-804E-76906EDC3E82 in sandbox C:\Windows\SoftwareDistribution\Download\d82fa884c766048f3875ae3333d09441_ctc
2014-08-06 09:04:15:798 1004 908 Handler Selecting self-contained because update does not have express payload.
2014-08-06 09:04:15:798 1004 908 Handler Selected payload type is ptSelfContained
2014-08-06 09:04:15:798 1004 908 Handler Detected download state is dsStart
2014-08-06 09:04:15:798 1004 908 Handler Adding Windows6.0-KB2855844-x86.cab (entire file) to request list.
2014-08-06 09:04:15:798 1004 908 Handler Request generation for CBS update complete with hr=0x0 and pfResetSandbox=0
2014-08-06 09:04:15:829 1004 908 Misc Validating signature for C:\Windows\SoftwareDistribution\Download\d82fa884c766048f3875ae3333d09441_ctc\Windows6.0-KB2855844-x86.cab:
2014-08-06 09:04:15:876 1004 908 Misc Microsoft signed: Yes
2014-08-06 09:04:15:876 1004 908 DnldMgr Asking handler to generate non-range requests.
2014-08-06 09:04:15:876 1004 908 Handler Generating request for CBS update 1941692E-A102-4EA0-804E-76906EDC3E82 in sandbox C:\Windows\SoftwareDistribution\Download\d82fa884c766048f3875ae3333d09441_ctc
2014-08-06 09:04:15:876 1004 908 Handler Selecting self-contained because update does not have express payload.
2014-08-06 09:04:15:876 1004 908 Handler Selected payload type is ptSelfContained
2014-08-06 09:04:15:876 1004 908 Handler Detected download state is dsHavePackage
2014-08-06 09:04:15:876 1004 908 Handler Request generation for CBS update complete with hr=0x0 and pfResetSandbox=0
2014-08-06 09:04:15:970 3612 e40 COMAPI -------------
2014-08-06 09:04:15:970 3612 e40 COMAPI -- START -- COMAPI: Install [ClientId = wusa]
2014-08-06 09:04:15:970 3612 e40 COMAPI ---------
2014-08-06 09:04:15:970 3612 e40 COMAPI   - Allow source prompts: Yes; Forced: No; Force quiet: No
2014-08-06 09:04:15:970 3612 e40 COMAPI   - Updates in request: 1
2014-08-06 09:04:15:970 3612 e40 COMAPI   - ServiceID = {91E7E2CD-C456-4147-AC0F-A4A217628611}
2014-08-06 09:04:15:970 3612 e40 COMAPI   - Updates to install = 1
2014-08-06 09:04:15:970 3612 e40 COMAPI <<-- SUBMITTED -- COMAPI: Install [ClientId = wusa]
2014-08-06 09:04:15:970 1004 e78 Agent *************
2014-08-06 09:04:15:970 1004 e78 Agent ** START ** Agent: Installing updates [CallerId = wusa]
2014-08-06 09:04:15:970 1004 e78 Agent *********
2014-08-06 09:04:15:985 1004 e78 Agent   * Updates to install = 1
2014-08-06 09:04:15:985 1004 e78 Agent   *   Title = Security Update for Windows (KB2855844)
2014-08-06 09:04:15:985 1004 e78 Agent   *   UpdateId = {DDD48962-1B38-478A-91B4-5DF779748AF7}.501
2014-08-06 09:04:15:985 1004 e78 Agent   *     Bundles 1 updates:
2014-08-06 09:04:15:985 1004 e78 Agent   *       {1941692E-A102-4EA0-804E-76906EDC3E82}.501
2014-08-06 09:04:16:859 1004 e78 Agent WARNING: LoadLibrary failed for srclient.dll with hr:8007007e
2014-08-06 09:04:16:859 1004 e78 Handler Attempting to create remote handler process as NT.MH.COM\ssiapp in session 2
2014-08-06 09:04:16:937 1004 e78 DnldMgr Preparing update for install, updateId = {1941692E-A102-4EA0-804E-76906EDC3E82}.501.
2014-08-06 09:04:16:937 3192 e74 Misc =========== Logging initialized (build: 7.0.6002.18005, tz: -0400) ===========
2014-08-06 09:04:16:937 3192 e74 Misc   = Process: C:\Windows\system32\wuauclt.exe
2014-08-06 09:04:16:937 3192 e74 Misc   = Module: C:\Windows\system32\wuaueng.dll
2014-08-06 09:04:16:937 3192 e74 Handler :::::::::::::
2014-08-06 09:04:16:937 3192 e74 Handler :: START :: Handler: CBS Install
2014-08-06 09:04:16:937 3192 e74 Handler :::::::::
2014-08-06 09:04:16:953 3192 e74 Handler Starting install of CBS update 1941692E-A102-4EA0-804E-76906EDC3E82
2014-08-06 09:04:16:953 3192 e74 Handler CBS package identity: Package_for_KB2855844~31bf3856ad364e35~x86~~6.0.1.2
2014-08-06 09:04:16:968 3192 e74 Handler Installing self-contained with source=C:\Windows\SoftwareDistribution\Download\d82fa884c766048f3875ae3333d09441\Windows6.0-KB2855844-x86.cab, workingdir=C:\Windows\SoftwareDistribution\Download\d82fa884c766048f3875ae3333d09441\inst
2014-08-06 09:04:42:522 3192 dc0 Handler FATAL: CBS called Error with 0x80070643,
2014-08-06 09:04:42:631 3192 e74 Handler FATAL: Completed install of CBS update with type=0, requiresReboot=0, installerError=1, hr=0x80070643
2014-08-06 09:04:42:631 3192 e74 Handler :::::::::
2014-08-06 09:04:42:631 3192 e74 Handler :: END :: Handler: CBS Install
2014-08-06 09:04:42:631 3192 e74 Handler :::::::::::::
2014-08-06 09:04:42:646 1004 e90 AU Can not perform non-interactive scan if AU is interactive-only
2014-08-06 09:04:42:646 1004 e78 Agent *********
2014-08-06 09:04:42:646 1004 e78 Agent ** END ** Agent: Installing updates [CallerId = wusa]
2014-08-06 09:04:42:646 1004 e78 Agent *************
2014-08-06 09:04:42:646 3612 fc8 COMAPI >>-- RESUMED -- COMAPI: Install [ClientId = wusa]
2014-08-06 09:04:42:646 3612 fc8 COMAPI   - Install call complete (succeeded = 0, succeeded with errors = 0, failed = 1, unaccounted = 0)
2014-08-06 09:04:42:646 3612 fc8 COMAPI   - Reboot required = No
2014-08-06 09:04:42:646 3612 fc8 COMAPI   - WARNING: Exit code = 0x00000000; Call error code = 0x80240022
2014-08-06 09:04:42:646 3612 fc8 COMAPI ---------
2014-08-06 09:04:42:646 3612 fc8 COMAPI -- END -- COMAPI: Install [ClientId = wusa]
2014-08-06 09:04:42:646 3612 fc8 COMAPI -------------
2014-08-06 09:04:47:638 1004 b10 Report REPORT EVENT: {42E5F80A-0B1F-449D-A915-B25411912282} 2014-08-06 09:04:42:631-0400 1 182 101 {DDD48962-1B38-478A-91B4-5DF779748AF7} 501 80070643 wusa Failure Content
Install Installation Failure: Windows failed to install the following update with error 0x80070643: Security Update for Windows (KB2855844).
2014-08-06 09:04:49:354 3612 e40 COMAPI ----------- COMAPI: IUpdateServiceManager::RemoveService -----------
2014-08-06 09:04:49:354 3612 e40 COMAPI   - ServiceId = {91e7e2cd-c456-4147-ac0f-a4a217628611}
2014-08-06 09:04:49:495 3612 e40 COMAPI IUpdateService removing volatile scan package service, serviceID = {91E7E2CD-C456-4147-AC0F-A4A217628611}
2014-08-06 09:04:49:495 1004 870 Agent WARNING: WU client fails CClientCallRecorder::RemoveService with error 0x80248014
2014-08-06 09:04:49:495 3612 e40 COMAPI WARNING: ISusInternal::RemoveService failed, hr=80248014
PDC

Hi,
I havea similar problemsomeonewas able tofix it?
I tried to install
manually kb but I can not
install any updates on many of my servers.
Manually:
014-08-13   21:10:55:373   572   ca0   Handler   Starting install of CBS update 627B5D1A-4F3F-4038-8C70-1824EAD5CEDC
2014-08-13   21:10:55:545   572   ca0   Handler   CBS package identity: Package_for_KB2918614~31bf3856ad364e35~amd64~~6.1.1.4
2014-08-13   21:10:55:561   572   ca0   Handler   Installing self-contained with source=C:\Windows\SoftwareDistribution\Download\0e7476712b0c0b923c90204546edc6d6\windows6.1-kb2918614-x64.cab,
workingdir=C:\Windows\SoftwareDistribution\Download\0e7476712b0c0b923c90204546edc6d6\inst
2014-08-13   21:11:02:082   572   958   Handler   FATAL: CBS called Error with 0x80070643,
2014-08-13   21:11:02:347   572   ca0   Handler   FATAL: Completed install of CBS update with type=0, requiresReboot=0, installerError=1, hr=0x80070643
014-08-13   20:45:42:449   948   2bc   Agent   *************
2014-08-13   20:45:42:449   948   2bc   Agent   ** START ** Agent: Finding updates [CallerId = AutomaticUpdates]
2014-08-13   20:45:42:449   948   2bc   Agent   *********
2014-08-13   20:45:42:449   948   2bc   Agent      * Online = No; Ignore download priority = No
2014-08-13   20:45:42:449   948   2bc   Agent      * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1
and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1"
2014-08-13   20:45:42:449   948   2bc   Agent      * ServiceID = {9482F4B4-E343-43B6-B170-9A65BC822C77} Windows Update
2014-08-13   20:45:42:449   948   2bc   Agent      * Search Scope = {Machine}
2014-08-13   20:45:42:449   4792   13e4   CltUI   AU client got new directive = 'Install Complete Ux', serviceId = {9482F4B4-E343-43B6-B170-9A65BC822C77}, return = 0
2014-08-13   20:45:42:449   948   2b4   AU   No featured updates notifications to show
2014-08-13   20:45:42:449   948   2b4   AU   Successfully wrote event for AU health state:0
2014-08-13   20:45:42:449   4792   13e4   CltUI   AU client got new directive = 'Shutdown', serviceId = {9482F4B4-E343-43B6-B170-9A65BC822C77}, return = 0
2014-08-13   20:45:42:481   948   12cc   AU   AU received handle event
2014-08-13   20:46:56:753   948   2bc   Handler   FATAL: UH: 0x80070490: EvaluateApplicability failed in CCbs::EvaluateApplicability
2014-08-13   20:46:56:940   948   2bc   Agent   WARNING: Failed to evaluate Installed rule, updateId = {8D75381D-A3D2-452F-A13E-67FF59E2081B}.101, hr = 80070490
2014-08-13   20:47:02:977   948   2bc   Handler   FATAL: UH: 0x80070490: EvaluateApplicability failed in CCbs::EvaluateApplicability
2014-08-13   20:47:47:001   948   2bc   Agent      * Added update {1E993966-A3B7-4075-9ECC-FF4290C4E811}.201 to search result
2014-08-13   20:47:47:001   948   2bc   Agent      * Added update {E20C4A54-DEE0-4641-A7D1-8EE452F8B54B}.200 to search result
2014-08-13   20:47:47:001   948   2bc   Agent      * Added update {2BDE2BA3-EF93-49C6-A3C6-A806835A680F}.200 to search result
2014-08-13   20:47:47:001   948   2bc   Agent   Update {0EEBE242-F0AD-4A1A-8796-4BFB54642198}.202 is pruned out due to potential supersedence
2014-08-13   20:47:47:001   948   2bc   Agent      * Added update {AEF6280F-8C4D-4804-9913-407582227E75}.202 to search result
2014-08-13   20:47:47:001   948   2bc   Agent      * Added update {9842D9DB-8AE8-4F0B-B974-66787AEC8FBC}.201 to search result
2014-08-13   20:47:47:001   948   2bc   Agent   Update {14C2118E-1CE2-447D-BFE7-BDB8F99969C0}.201 is pruned out due to potential supersedence
2014-08-13   20:47:47:001   948   2bc   Agent   Update {CB1F1FAE-F738-49E7-AE3E-7A0C2308838B}.201 is pruned out due to potential supersedence
2014-08-13   20:47:47:001   948   2bc   Agent   Update {23AE2211-ABC3-497A-BB21-D9782B26A6EC}.202 is pruned out due to potential supersedence
2014-08-13   20:47:47:001   948   2bc   Agent   Update {1494DE3C-4764-42DB-B5D5-A5509D7EEB26}.201 is pruned out due to potential supersedence
Any idea? Thx!

Sunfire X2250 endless restarting after putting on all 'security' updates

Hello all, yeserday I did a fresh Solaris install and once that was done i ran updatemanager. I selected only the 'security' updates. They downloaded and then installed. I then got a screen prompted me to reboot, so i ticked the box and let the machine do its thing. So the machine goes through and installs the remaining patches and the reboots. Upon reboot right after grub where i select Solaris to boot i get the Sun solaris copyright screen and right after that a bunch of 'unknown symbol' messages all over the place. The machine doesn't even get back to the desktop or login and enters maintenace mode. I was stuck at this point, I didn't know what to do and couldn't go any further and so I did a complete reinstall of the OS again. Once it came back up I again ran updatemanager and selected only the 'security' updates. It did the same thing again! upon the shutdown/reboot sequence the system hangs again, endless reboot loop. Why are these basic security patches messing up the machine? is there a known bad patch that bonks everything? I now have everything reinstalled again (3rd OS reinstall) and it's running great but i'm scared to run the patches again. Can anyone please help or provide an explaination? thank you very much in advance

Thanks for your reply, scapesuiter.
I suppose i can rule out third party software, as, after i reinstalled my OS after the first freezing (after 2007-003), i did not add anything else. At that point there was nothing on my computer but what came on the original install disks. I tried downloading and installing 2007-003 again and the same thing happened, and i had to reinstall again.
However, i do have 1GB RAM that i did not order from Apple. My computer originally came with 512 but i bought more some time ago (can't remember exactly when).
I also bought a new hard drive, also not from Apple, at around the same time.
But i should say again that i've had no problems since getting the new hardware, other than with these particular security updates (2007-003 and 2006-007). All the other security updates went well, as well as all other software updates.
(I also did a hardware check with my Apple Hardware Test disk and it indicated that everything was working fine.)
PowerBook G4 Mac OS X (10.3.9) Ti 800MHz 1GBRAM 100GB Internal Drive

After downloading the latest security update of lion 107.3, I lost the app store and when attempting to download anything lion I receive a plug in failed message?

after downloading lion security update 10.7.3 I lost the app store and when attempting to download anything lion I receive a plug in failure message, what is the fix?

Download a fresh Firefox copy and save the file to the desktop.
* Firefox 4.0.x: http://www.mozilla.com/en-US/firefox/all.html
* Firefox 3.6.x: http://www.mozilla.com/en-US/firefox/all-older.html
* Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
* Do not remove personal data if you uninstall the current version.
* It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
Your bookmarks and other profile data are stored elsewhere in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder] and won't be affected by a reinstall, but make sure that you do not select to remove personal data if you uninstall Firefox.

After installing recent java + security update, computer will not sleep

After installing the recent java, daylight savings, and the security update. my computer will not sleep. Does anyone else have this problem? I do have an adaptec usb2 card installed but nothing is plugged into it. Also i don't have any Ipods or external things plugged in. I have had the same setup for the past year with no problems, now it will not sleep. I have also tried repairing the permissions. Please help

When you select Sleep from the Apple Menu nothing happens, is that correct? Try this: Go menu > Home > Library > Preferences. Drag the whole of the Preferences folder to the desktop. Restart your mac, don’t worry if things look different, you have not lost anything. Can the mac sleep now? If yes, then its a damaged or corrupted .plist or preference. If you are using Apple Mail, drag the com.apple.mail.plist back to the new preferences folder created on reboot, you dont really need anything else but keep hold of the old preferences (the one you dragged to your desktop) just in case for a month or two. If everything else is OK you can safely delete it. If it has not cured the problem then remove the new preferences folder created on reboot by taking it to the trash, drag back the preferences folder you moved to the desktop and reboot. Now reinstall a clean OS. See how you go from there

Mouse problems after 11/29/05 Security Update?

I installed the 11/29/2005 Security Update 2005-009 via Software Update. Right afterwards (even before the required reboot), I began having mouse oddities. The cursor disappears from the screen, or just stays there and doesn't move. Moving the mouse won't make the cursor move. I must click the mouse before the cursor "wakes up" and responds to the mouse. It's fine after that.
I'm using a Logitech cordless optical mouse. Batteries are fresh and this only begain right after installing the Security Update. Anyone else experiencing this?
[ Edited by Apple Discussions Moderator; added update ID 2005-009 ]

I have resolved the issue! As I mentioned, I am using a Logitech cordless optical mouse. I connected up my Apple keyboard & mouse and disconnected the Logitech. The problem no longer occurred with the Apple mouse.
I removed the batteries from the Logitech mouse and disconnected the USB receiver. Restarted the computer, reconnected the Logitech setup, disconnected the Apple stuff, and now it is working.

IBook G4 won't start up after installing promted itunes & security update

HELP.
My iBook G4 was prompted to update iTunes & some security update. I always do this when prompted, and restart as requested.
I installed the updates and restarted, but this time my iBook won't boot up. It makes the regular chime noise, goes to the gray screen, gets past the apple logo, then goes to a blue screen with the cursor in the upper left corner. The cursor moves just fine, the caps & num lock lights work, but it just never gets past the blue. If I leave it alone for a while, the cursor disappears, and I get the turning circle in the lower middle of the screen (the one that comes up during the gray screen). It just sits and sits on the blue. Hard drive isn't making any unusual sounds.
I tried starting it up from the Install Disc, which worked fine. I ran the disk utility and it said it didn't need any repairs.
Still won't start up.
I did the cmd + opt + p + r to get the 3 chimes... no change.
I tried the fsck thing, it didn't do anything.
HELP.
Am I a goner?
I saw that some other people had problems, but it seems like everybody's is just slightly different. My display looks totally normal, just won't get past the blue screen. My disk utility said that it didn't need any repairs? Looks like most other people at least saw some errors in there...

I think Carolyn misunderstood the "3 chimes" comment. I think what you meant was that you held down the key combo until you heard the normal startup chime for the third time, not that the iBook gave you the 3 long beeps of a failed POST (power-on self test) which could indeed indicate a RAM problem.
It's more than likely not a RAM issue. These bad updates occasionally happen and the way to handle it is to do what you're doing now; backup what you can and then do an Archive and Install of the OS (although usually a couple of reboots, start in safe boot mode and reinstall the update is usually all that's needed).

Login status Error after install of new security update on 3-11-15

I am having this issue only after I installed the latest Security update. Now I am unable to install the iMovie update, or log into the app store.

As Patrick says Apple having server issues since early AM at least.
As I posted else where…
Hey everyone with Apple problems right now…
Apple is having server problems affecting App Store, iTunes, iCloud, etc…
Check the Apple Service Status(***) page… http://www.apple.com/support/systemstatus/
Wait for all systems green. This is always a good idea if you have problems with anything Apple.
Here is what Apple message says…
Multiple Store Services - All users are affected
Customers may be unable to make purchases from the App Store, iTunes Store, iBooks Store, or Mac App Store.
iCloud Mail - All users were affected
Users may have been unable to access iCloud mail.
iCloud Account & Sign In - All users were affected
Users may have been unable to sign in.
This means no downloads, updates, iCloud and other issues. You may get pop-up windows asking you for password for iCloud, etc…
Wait, try again after all go to go on *** page.
Hope this helps, Greg

Loss of FN-Keys after installation of Microsoft security updates on L500

Similar Messages

Maybe you are looking for