Lost 5 GHz wireless network access after upgrading to Windows 10

Hello, Lost the ability to connect to (and see) my 5GHz wireless network after upgrading Windows 8.1 to Windows 10 on my Yoga 2 13. I have tried to update the wireless driver to the latest version. The WiFi card is the original Wireless-N 7260 that was installed when I bought the computer. I know for a fact that I was able to use 5GHz networks Before as I can see my saved networks and I can clearly see that I have my 5GHz network in that list. Please advice, Patrik

Good to see it fixed itself. One setting that can block Windows 10 from seeing the WD My Cloud and other devices/computers on the network is the "network location type". During the upgrade or install to Windows 10 one may not quite understand what they are reading when, or if, asked which kind of network they are connecting to. If they select "no" on that particular screen (example below), Windows 10 will block access to certain local devices possibly including the WD My Cloud. The following link gives a general overview of the issue and ways to fix it if one made the wrong selection: Change network location type (Public or Private) in Windows 10 

Similar Messages

  • Networking Issues after Upgrading to Windows 8.1

    I have a Windows 8 desktop PC that is working fine with my network.  I can browse the Internet fine using all major browsers etc.  After upgrading to Windows 8.1 through the Windows Store I noticed that my wired networking was not working correctly.
     The status of the network does not change (i.e. it doesn't change to Limited Connectivity) however browsing to sites in Chrome, IE or Firefox doesn't work as well as Windows 8.
    IE11 gives me the error "This page can't be displayed, make sure the web address is correct" and other browsers give a similar error.  I normally have to refresh 2-3 times to get a new page to load, sometimes even more.  Everything works
    fine from a laptop connected at the same time so it isn't an network issue with my provider.
    I thought this might be a driver issue with the two on-board Marvell wired network adapters.   I wasn't able to rollback the driver to older versions I found on the Internet.  I then purchased another network card, Intel Desktop gigabit and the
    issue still persists with that adapter.  I then tried a USB wireless adapter and the issue still persists using wifi with the wired adapters disabled.  I tried a new network cable and no luck either.  I also tried resetting the IP stack using
    the various netsh commands.
    After that I thought I might try reset the Windows 8.1 PC, however that didn't work as I didn't have the restore image available as I upgraded from the Windows Store.  I then tried installing Windows 8.1 fresh using a ISO with my Windows 8 key using
    some of the recent guides that are available.  That all worked but it didn't fix the networking issues.
    I re-installed Windows 8.0 and the networking is now fixed and back to working normal again.  I'd like to try again but I think I will have the same problems.  I can't imagine why this would be a driver issue as I tried 3 different network adapters
    and two installs of Windows 8.1.  Any ideas what would be the cause of the Windows 8.1 issue?

    HI,
    Since this issue only occurred in the your desktop PC, and many network adapters you tried, failed, thus I think maybe we should focus on the model of your desktop PC, I suggest you update the BIOS and chipset from the manufacture to improve
    the performance of win8.1.
    Please also test this issue in safe mode with networking.
    Please refer to:
    Windows Startup Settings (including safe mode)
    http://windows.microsoft.com/en-in/windows-8/windows-startup-settings-including-safe-mode
    I’d like to share the following article with you:
    Wired and wireless network problems
    http://windows.microsoft.com/en-IN/windows/network-connection-problem-help#network-problems=windows-81&v1h=win81tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1
    Regards,
    Yolanda
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.
    The issue occurs in safe mode as well under Windows 8.1.  The motherboard is an Asus P5B Premium, however it works on Windows 8.  How would I update the chipset when booted into Windows 8.1?  In Device Manager it wasn't allowing me to update
    the network drivers as they were newer versions already installed.
    Edit:  I also installed at Intel Chipset Device software dated 8/8/2013 with version 9.​4.​0.​1026 and the issue still occurs.  I am also running the latest BIOS that is available.

  • WRT54G wireless not working after upgrading to windows vista, please help

    Hello everyone....
    I have a few problems. I upgraded to Windows Vista and cant seem to get my wireless internet working. My router is WRT54G wireless-g broadband router. Ever since I upgraded Vista my xbox 360 will not connect.
    I just bought a new wireless web camera and that does not work either because the wireless is not working.
    Any suggestions on what I should do to solve this issue?
    I noticed when I goto 192.168.1.1 my firmware version is Firmware Version: v3.03.9 does that have anything to do with it? Is there a more up-to-date version that will help?
    Hope to hear from someone.

    I have the same problem, and so does my son, he has a toshiba satellite new laptop and I have an acer new laptop, both have Vista on them, and my wife has XP and has no problem getting on teh router, but i have this problem everyday.
    Eventually it will all of a sudden show up and connect and start working, then if you laeave your computer in standby movde overnight, it will still work in the morning, but if you shut down comeplety you will lose the connection for who knows how long. what is the fix Linksys?
    (Edited post for guideline compliance. Thanks!)
    Message Edited by JOHNDOE_06 on 12-28-2007 07:28 AM

  • Keyboard wireless key not working after upgrading to windows 8.1

    Hello,
    I am having hp pavilion dv6-6165tx notebook, where keyboard having a wireless button that turns ON and OFF all wireless devices, After upgrading to windows 8.1, HP Connection Manager is not getting installed, as well as Key is not working, key color turns red and white but no action is performed.
    Kindly suggest me some solution.
    Note: HP Doesn't provide drivers for windows 8/8.1 ONLY WINDOWS 7 for hp pavilion dv6-6165tx.
    Thanks.

    Hi @Jayesh_Bhadja ,
    Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion dv6-6165tx Notebook and the Wireless keyboard not working correctly. Here is a link to troubleshoot the keyboard.
    The HP Connection Manager is something that is for Windows 7 not Windows 8.1. I would uninstall this from your Notebook.  Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating. It has a troubleshooting tool in this.
    Make sure all your updates have been completed. I would try restarting my Notebook a few times.
    If that does not help I would uninstall the keyboard from the Device manager.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • I lost hundreds of pictures from iPhoto after upgrading to Mavericks

    I lost hundreds of pictures from iphoto after upgrading to mavericks. does anyone know why or how to retrieve them. i cannot find them on time machine either.

    and
    Why do you think you have lost "hundreds" of pictures?
    What exactly are you seeing
    You can try Back up your iPhoto library, Depress and hold the option (alt) and command keys and launch iPhoto - rebuild your iPhoto library database
    LN

  • WRT610N : laptops cannot connect to 5 Ghz wireless network !

    Hello,
    I have a Linksys WRT610N (hardware v1) router, and i configured the wireless settings for the 5 Ghz and the 2.4 Ghz
    wireless network, but the problem is that my laptops (wifi n compatible) only detect the 2.4 Ghz network, but NOT the
    5 Ghz network.  I have no clue what the problem might be :-(
    These are my configurations :
    Settings for wireless network (5 Ghz) :
    network mode : only wireless-n
    network name (SSID) : WRT610WiFi-N
    channel width : auto (20 or 40 Mhz)
    wide channel : auto (DFS)
    standard channel : auto (DFS)
    SSID broadcast : enabled
    Settings for wireless network (2.4 Ghz) :
    network mode : only wireless-g
    network name (SSID) : WRT610WiFi-G
    channel width : only 20 Mhz
    wide channel : auto
    standard channel : auto
    SSID broadcast : enabled
    Security Mode on both is "WPA2-personal", and encryption is "WPA-TKIP or WPA2-AES"
    But my laptops only see the WRT610WiFi-G, and not the other one :-(
    I am somewhat disappointed currently, as you can understand, but hopefully someone here can
    provide me with a solution for this problem...
    best regards,
    Chris.
    Solved!
    Go to Solution.

    Correct. Should be a/b/g/n

  • I lost my i-tunes online purchase after upgrade to snow leopard...

    Hi
    I lost my i-tunes online purchases after upgrade to snow leopard...
    Is there any way to retrieve them?
    Thanks

    kakalos wrote:
    you are both great!!!
    i found them
    it was at the folder you suggested!!!
    i am so happy
    thanks so much!!!!
    Awesome. I had a feeling it could still be there. I'm very happy for you!
    Two things you can do now:
    1.) Add all of these files into iTunes by using "Add to Library" and selecting the iTunes Media folder. This is the easiest method, but you lose your original iTunes settings, playlists, play counts, ratings, etc.
    2.) A slightly more advanced method however will let you salvage your iTunes library and restore it the way it was before. Use finder to look at Music/iTunes/Previous iTunes Libraries. In that folder, check to see if there is one dated near today's date (or when the reset happened to you). If there is a very recent one, you can restore to that date. What you'll want to do is take that file, and MOVE it back up one level to the iTunes folder.
    Currently in your iTunes folder is a file named iTunes Library (this is the active, and blank one) and now you should have the dated one as well. You can DELETE the iTunes Library one, and rename the dated one "iTunes Library".
    Then hold OPTION while loading iTunes, and when asked to choose a library, select Choose Library, and navigate to Music/iTunes, and pick the "iTunes Library" file you just moved and renamed.
    If all goes well, your songs, playlists, ratings, and etc. should all be back to the way it was. Just do "Add to Library" and select the iTunes Media folder to make sure nothing was excluded between the backup and your copy before it reset.
    Hope this helps!

  • Lost you tube from home screen after upgrading to os6?

    I've lost you tube from home screen after upgrading iPad software. Is this normal?

    Sorry, no YouTube in IOS 6.
    You can use the iPhone version of YouTube or Jasmine
    http://itunes.apple.com/sg/app/youtube/id544007664?mt=8
    https://itunes.apple.com/sg/app/jasmine-youtube-client/id554937050?mt=8

  • E4200 Can't see my network shares after upgrade

    I can't see my network shares after upgrade altough everything works fine , the network scanner shows all the atatched devices but in Eplorer when I click Network there is nothing shown on two computers running Win7 64.
    I did downgraded the firmware back to .01 but still no network .
    Any help ?

    After upgrading the firmware did you reset the E4200? After successful firmware upgrade you need to reset the router. It is recommended to reset the router once. Steps to reset the router:
     Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. Power light should blink when you perform the reset process.
    After reset, reconfigure the router and then check the connectivity status…

  • I unable to see my network messages after upgrading to ios6 on my iphone4,can anyone help me for this issue?

    I unable to see my network messages after upgrading to ios6 on my iphone4,can anyone help me for this issue?

    Try to perform SMC and PRAM resets:
    http://support.apple.com/kb/HT3964
    http://support.apple.com/kb/ht1379
    Then try a safe boot:
    http://support.apple.com/kb/HT1564
    Ciao.

  • TS3276 I lost the ability to send email after upgrading to maverick.

    I lost the ability to send email after upgrading to maverick.  Has anyone  else had this problem?

    Mail troubleshooting - Yosemite
    What does Mail/Window/Connection Doctor Show? If the server is red, select it and look at the Show Details box.
    Troubleshooting sending and receiving email messages
    Troubleshooting sending email messages

  • Linksys Easy Link Advisor for WRT310N Wireless Router after upgrading to Windows 7 (64bit)

    I can't reinstall Linksys Easy Link Advisor for WRT310N Wireless Router after upgrading to Windows 7 (64bit).  When I went to Linksys site for solution for new drivers, it asked me for Hardware Version Number.  This model doesn't show one.  Any thoughts?
    Thanks!

    Sabertooth is right. If you are able to go online from your Router then you don't need to install LELA software on your Computer.

  • After upgrading my windows 8.1 PC to windows 10, my Acer T272HL 27" touchscreen lost touch functions

    After upgrading my windows 8.1 PC to Windows 10, my Acer T272HL 27" touchscreen monitor is no longer listed as being touch compliant, has lost all touchscreen functionality, and the hid touchscreen listing has disappeared from the device manager: frustrated! Have, of course, uninstalled & reinstalled the monitor correctly,& windows still denotes it as non touchscreen. Of course, hdmi cable & USB 3.0 cables firmly connected....Thanks much in advance..

    cathound7,
    There should be something listed in the USB section for the monitor touch functionality. My only suggestion would be to uninstall the drivers for the monitor (again), remove the USB cable, and restart the system. See if it picks up the monitor and tries to install the drivers, then connect the USB cable and see if it tried to install the touch functionality.

  • S3-S440 no wifi after upgrading to Windows 8.1

    After upgrading to windows 8.1, the wifi is not working anymore.
    I cannot find the wifi driver in the device managerment and I cannot see any information about wifi driver.
    I try to re-setup the driver many times and checked the wireless module was enabled in the BIOS. But it is no progressing at all. I can only access to the Internet through the wire now...
    Please help me.!!!

    Salheureux, welcome to the forum.
    You should go into the Control Panel / Sound to assure that your sound device is set to Default.  Also, right click on the speaker icon in the Taskbar / Playback devices and check that your speakers are displayed.
    Please click the "Thumbs Up+ button" if I have helped you and click "Accept as Solution" if your problem is solved.
    Signature:
    HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
    HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
    HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
    HP Photosmart 7520 AIO
    ++++++++++++++++++
    **Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
    Intelligence is God given; Wisdom is the sum of our mistakes!
    I am not an HP employee.

  • Wifi problem of G560 after upgrading to windows 8.1

    Hi,
    I have a lenovo G560. After upgrading from windows 8 to windows 8.1, I cannot connect to wifi. I was wondering if someon else has the same problem.

    hi amardoukhi,
    Welcome to the Forums.
    Your issue might be similar to this thread. Try the solution that was posted to rollback to an older driver version.
    The solution was to:
    1. Open Device Manager (press WInkey+R > type devmgmt.msc)
    2. On the Device Manager, navigate to Network Adapters > right click on the wireless adapter and choose Update Driver Software
       - Link to picture
    3. On the Driver Update Window, choose Browse my computer for driver software >  Let me pick from a list of device drivers on my computer and choose the wireless card on the list.
       - Link to picture
       - Link to picture
       - Link to picture
    Regards
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

Maybe you are looking for

  • Web application platforms for Azure

    I have an application that resides in Azure and consists of a SQL database, a website that serves as the UI, and a Web API that exists simply to provide data from the SQL database to the API. The UI is a lightweight SPA developed in Durandal and Knoc

  • TypeError: Error #2007: Parameter text must be non-null

    I am new to AS period, but I am following some training videos for AS 3.0 to create a portfolio site where the images and text are loaded by xml. I have followed the instructions to the letter; however I am getting the #2007 Parameter text must be no

  • Get cl_gui_alv_grid header commentary

    Hello, I am using BADI FI_ITEMS_MENU01(t. FBL3N ...)  for upload cl_gui_alv_grid content to Excel, but i dont know how i can to get alv header commentary from the reference to cl_gui_alv_grid. Is there any possibility to do that? Thank you in advance

  • Displaying images through forms6 stored as bfile

    The image is stored in a database as bfile datatype. How the image can be displayed using forms6?

  • Error in an Invoice Form Printing?

    Hi All, The customer is facing a problem when he is trying to generate a invoice with more than 3 line items in the line items window, whenever he is trying to process more than 3 line items, it is printing but overlapping the subtotal window, pleas