Lost connection of 2 client laptops to internet via LAN on WRT320N wireless-N dual channel router

The connection of almost 2 yr. old router to DSL modum was unstable recently. They're hardwaired to my desktop. A Cisco customer rep recommended downloading an "upgrade firmware" for the unit, and I did that. It seemed to have made the internet connection stable for the desktop, but now I can't connect the both 2 laptops to the network. The network and its properties are detected by each of them, but it appears the internal setting(s) are now out of sync with those of the router. Any help.

Assuming your two laptops are wireless, after you upgraded the firmware an reset the router you have to reconfigure it. You have to input your wireless network settings again and make them match with your laptops. Has this been done?

Similar Messages

I don't have a DSL or cable modem to access the Internet ... just a mobile WiFi (there is no cable available at our house). How do I connect my Time Capsule to the Internet via the mobile WiFi?

I don't have a DSL or cable modem to access the Internet ... just a mobile WiFi (there is no cable available at our house and the mobile WiFi is our only option). How do I connect my Time Capsule to the Internet via the mobile WiFi?

LOL!!
I am in Australia and the ISP... I think both the main ones would fit your description to a T.. big T in particular.
Your router is really unsuitable.. if it is only wireless and no ethernet.. just buy an ethernet one.
Do a search on ebay.. 3g router.
But you can get the TC to join a wireless network.
It is a non-standard setup that Apple will not support.. the option is hidden.
If you are on Lion download the 5.6 utility. Go to the wireless set up page and hold down the option key whilst selecting wireless mode.. a new option, join will appear. You can then put in the ssid and passkey of the 3g router.
But please note the end result of this setup..
very slow speed. The TC is now a second wireless hop from your clients.. this will halve the speed.
In this mode the ethernet are deactived.. for reasons only Apple know, they decided you should not use ethernet when doing this.

Satellite Pro P100 - Can't connect to Internet via LAN

I have a Toshiba Satellite Pro P100. Model No SPSA4A-005002
I used my recovery disk and wiped my computer, because of a virus and now I cant connect to the internet via cable but my wireless internet works perfectly.
Its completely dead there are no lights at the back of the laptop from where I plug the cable in.

Hi
Is your LAN card recognized properly in device manager?
In your case I would try updating the LAN driver. You can get the latest version here:
http://eu.computers.toshiba-europe.com > Support & Downloads > Download Drivers
Furthermore you check the BIOS version. The latest version should be installed and load the default settings there.
In worst case its a hardware problem and you have to exchange the whole mainboard :(

Can't connect my new iPhone 4 with internet via Time Capsule. IP4 recognized TC but will not connect with it. (Password etc. is ok)

Can't connect my new iPhone 4 with internet via Time Capsule. IP4 recognized TC but will not connect with it. (Password etc. is ok)

Do the usual wireless things.
Change the wireless name to simple name with only alphanumerics and no spaces.
Set to manual and use channels 1, 6, 11 in turn.
For testing take off the security altogether.
The iphone only works on 2.4ghz so only that band is relevant.

Hi, I'm thinking of buying the Airport Express or Extreme for my school dormitory, would i need to plug them into the already existing school internet via LAN cable or do the products just work by themselves?

Hi, I'm thinking of buying the Airport Express or Extreme for my school dormitory, would i need to plug them into the already existing school internet via LAN cable or do the products just work by themselves?

Welcome to Apple Support Communities
AirPort stations aren't modems, so they have to be connected to the modem you are already using. The AirPort Extreme and Express have a WAN port, where you have to plug an Ethernet cable that has to be connected to the modem.
After doing this, you can set up the AirPort station by using AirPort Utility. If you have Windows, download AirPort Utility from the Apple website > http://support.apple.com/kb/dl1547

Connecting laptop to internet via mobile phone

I would like to connect my Toshiba Portege laptop to the internet via my Nokia 6280 phone using bluetooth.
I have a connection between the two using nokia pc suit but cannot get internet connection to work.
The phone connects to the internet OK. I did try setting the connection up once but the could only get it to use IR the laptop wanted to know loads of information that I did not have, I think it was all set up on the phone via text message download.
Anyway, any information/experiances you have would be much appreciated.
Chris

@judinme
Welcome to the forum!
White screen on Nokia not good news, try removing battery for 10 minutes and replace, if no luck a visit to Nokia Care Point may be needed.
Happy to have helped forum with a Support Ratio = 42.5

Connecting a powerbook G3 to the internet via ethernet and a DSL modem. Does the G3 have the ability to do this?

I am trying to connect an older powerbook G3 (M4753) to the internet via ethernet and a DSL modem. Does the G3 have the ability to do this? I'm having alot of trouble. G3 Dialog box states the DHCP server will populate IP address, etc. It does not. The G3 also insists I enter the DHCP client ID.

Anything useful in the following articles?
http://support.apple.com/kb/TA20782
http://support.apple.com/kb/TA20785
Jan

Trying to Connect iBook to Internet Via Windows PC Verizon Wireless Card

I have a Windows PC laptop (IBM Thinkpad) that has a built-in Verizon wireless broadband card, which allows me to connect to the Internet from any location. I'm trying to find a way to share this connection with a Mac iBook. I can hook the two computers to each other with an ethernet cable, but then I can't figure out what to do to allow the iBook to access the PC's internet connection?
BTW - the PC is running XP, the iBook OS 10.4 (and Airport, although this doesn't seem like an Airport-related issue).
Any help would be greatly appreciated. Thanks!
Matthew

Do I need an Air Port Base station or a router? After I set up everything on my mac mini, what steps do I need to follow on the iBook to get Internet access?
The AirPort base station is a router. You are not limited to AirPort base stations as non-Apple 802.11g routers (like those from Belkin, D-Link, or Linksys) will work just as well. Using a router, your network configuration would be something like the following:
Cable modem > (Ethernet cable) > [WAN] router > (wireless) > wireless computers.
The set up for both computers, to access the router, would basically be the same.
To setup AirPort for High-Speed Cable Internet connectivity:
System Preferences > Network > Show > Network Port Configurations
- Verify that an AirPort option exists. If it does not, click "New" to create one. (Note: If you are unable to create an AirPort configuration, the AirPort card in your computer either doesn't exist or it is not recognized.)
- Verify that AirPort is "On" (checked)
- Verify that AirPort is at the top of the list. If it isn't, you can drag it to the top.
Systems Preferences > Network > Show > AirPort
AirPort tab
- By default, join: Automatic
TCP/IP tab
- Configure IPv4: Using DHCP
- Configure IPv6: Automatically or Off
Proxies tab
- Configure Proxies: Manually
- Select a proxy server to configure: <All proxies should be unchecked unless you specifically require a proxy for Internet access.>
- Exclude simple hostnames (unchecked)
- Bypass proxy settings for these Hosts & Domains: <leave blank>
- Use Passive FTP Mode (PASV) (checked)

Connect Time Capsule with Samsung LED TV via LAN - will it work?

Hi. I am from Germany and my englisch is very bad. Sorry for that.
I want to by a Time Capsual and a Samsung LED TV with LAN integrated.
I want to connect the Time Capsual via LAN to the TV to watch Movies, listen Musik and watch Pictures. I have not found any informations, if that will work.
I hope you understand my question and somebody can help me. Thanks

narfist wrote:
Hi. I am from Germany and my englisch is very bad. Sorry for that.
hi narfist and welcome to the discussion area !
I want to connect the Time Capsual via LAN to the TV to watch Movies, listen Musik and watch Pictures. I have not found any informations, if that will work.
it will not !
consider getting an Apple TV. you can store content locally on the ATV or you can keep your iTunes media folder on the time capsule but would need iTunes to be running on your Mac to stream content to the TV (via Apple TV).
good computing

Intermittent Internet Connection and VPN clients can't ping internal LAN but connected after installating cisco ASA5512x

Hi!
I wish someone can help me on this, I'm a new guy on cisco firewalls and I'm currently implementing cisco asa 5512x, here are the details:
ISP -> Firewall -> Core switch -> Internal LAN
after installing the cisco asa and terminating the appropriate lan for the outside and inside interfaces, internet seems intermittent and cisco vpn client can connect with internet connection but can't ping internal LAN.
here's my configuration from my firewall.
ASA Version 8.6(1)2
hostname ciscofirewall
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 203.x.x.x 255.255.255.0
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 10.152.11.15 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
dns domain-lookup outside
dns domain-lookup inside
dns server-group DefaultDNS
name-server 4.2.2.2 -------> public DNS
name-server 8.8.8.8 -------> public
name-server 203.x.x.x ----> Clients DNS
name-server 203.x.x.x -----> Clients DNS
same-security-traffic permit intra-interface
object network net_access
subnet 10.0.0.0 255.0.0.0
object network citrix_server
host 10.152.11.21
object network NETWORK_OBJ_10.10.10.0_28
subnet 10.10.10.0 255.255.255.240
object network NETWORK_OBJ_10.0.0.0_8
subnet 10.0.0.0 255.0.0.0
object network InterconHotel
subnet 10.152.11.0 255.255.255.0
access-list net_surf extended permit ip any any
access-list net_surf extended permit ip object NETWORK_OBJ_10.10.10.0_28 object InterconHotel
access-list outside_access extended permit tcp any object citrix_server eq www
access-list outside_access extended permit ip object NETWORK_OBJ_10.10.10.0_28 any
access-list outsidevpn_splitTunnelAcl standard permit 10.152.11.0 255.255.255.0
access-list LAN_Users remark LAN_clients
access-list LAN_Users standard permit any
access-list vpnpool extended permit ip 10.10.10.0 255.255.255.248 any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu outside 1500
mtu inside 1500
ip local pool vpnpool 10.10.10.1-10.10.10.6 mask 255.255.255.248
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 no-proxy-arp route-lookup
object network net_access
nat (inside,outside) dynamic interface
object network citrix_server
nat (inside,outside) static 203.177.18.234 service tcp www www
object network NETWORK_OBJ_10.10.10.0_28
nat (any,outside) dynamic interface
object network InterconHotel
nat (inside,outside) dynamic interface dns
access-group outside_access in interface outside
access-group net_surf out interface outside
route outside 0.0.0.0 0.0.0.0 203.x.x.x 1
route outside 10.10.10.0 255.255.255.248 10.152.11.15 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication telnet console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.0.0.100 255.255.255.255 inside
http 10.10.10.0 255.255.255.240 outside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ikev1 enable outside
crypto ikev1 enable inside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
client-update enable
telnet 10.152.11.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
enable outside
anyconnect-essentials
group-policy outsidevpn internal
group-policy outsidevpn attributes
dns-server value 203.x.x.x 203.x.x.x
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client
split-tunnel-policy tunnelall
split-tunnel-network-list value outsidevpn_splitTunnelAcl
default-domain value interconti.com
address-pools value vpnpool
username test1 password i1lji/GiOWB67bAs encrypted privilege 5
username test1 attributes
vpn-group-policy outsidevpn
username mnlha password WlzjmENGEEZmT9LA encrypted
username mnlha attributes
vpn-group-policy outsidevpn
username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 15
tunnel-group outsidevpn type remote-access
tunnel-group outsidevpn general-attributes
address-pool (inside) vpnpool
address-pool vpnpool
authentication-server-group (outside) LOCAL
default-group-policy outsidevpn
tunnel-group outsidevpn ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect http
inspect ipsec-pass-thru
class class-default
user-statistics accounting
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
hpm topN enable
Cryptochecksum:edc30dda08e5800fc35b72dd6e1d88d7
: end
thanks. please help.

I think you should change your nat-exemption rule to smth more general, like
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 no-proxy-arp route-lookup
'cause your inside networks are not the same as your vpn-pool subnet.
Plus, if you're trying to reach inside subnets, different from 10.152.11.0 255.255.255.0 (ip from wich subnet is assignet to your inside interface, and for wich above nat exception should be enough), you should check if routing is configured from that subnets to your vpn-pool-subnet through the ASA.

Connecting laptop to internet via cell phone

I heard i can use my cell phone to connect my laptop to the internet, i currently have a lg envy touch , with a 25 megabyte plan which would not be enough as I am wanting to get rid of current dsl plan and wanting to use my wireless plan as my only paid source of internet connection in my home.
I can upgrade plan to unlimited for 29.99 per month which is what i currently pay for my home dsl. I was told by verizon rep i could use a smartphone ( droid/ droid incredible) to set up a wireless connection in which i could also use my ipod and nintendo dsi to connect to internet as well at the same time as the laptop.
So my thinking is i add another line to my 2100 minute family plan for additional monthly cost of 9.99 get the droid for 199.99 with the unlimited plan of 29.99 bringing my total monthly bill to 170.00 minus taxes. I currently only use about 900-1000 minutes but the savings of dropping minutes just doesnt seem worth it to me as I have children on my plan and their minutes will increase at some point and I would rather be locked in to a plan that gives me more than needed.
So I am wondering if others on this forum could give me their opinion/advise?
Does anyone else use the unlimited 29.99 plan as their only source of internet connection? and how fast/slow etc?
If it matters I will be using the internet connection in Pasadena Texas and mainly we use the internet for general searches on basic info, job searches, facebook, ipod music, no gaming or anything complicated, just a typical basic internet family use.
Thank you so much!
Shannon

In addition to the unlimited $29.99 data plan, you would also need a $29.99 tethering plan, so it would cost you $60 a month - and the connection would not be as good as your DSL. And we use our DSL to connect to a router and have several laptops and desktops using our DSL, which would not work with a tethered connection. My advice - skip the tethering and keep the DSL.

New iMAC - want to connect PC Laptop to Internet via iMAC Airport

Hello - I have a new IMAC and the Internet connection to the IMAC is fine but I'm having trouble establishing a wireless network.
The store told me that I could use the Airport built into the MAC as a wireless router so that my PC laptop can access the Internet as well. My PC laptop is running Windows 2000 - and I have used it with a wireless router previously.
I can see the iMAC wireless network connection in my laptop's available network; however, I'm unable to connect to it.
Also, my IMAC system properties for Airport indicate that the wireless network is unavailable.
I've not selected any security settings - unless there's some default settings that I'm not aware of.
Advice or suggestions please???

The store told me that I could use the Airport built into the MAC as a wireless router so that my PC laptop can access the Internet as well.
That's correct. You will be using your Mac OS X's Internet Sharing feature to share your iMac's wired Internet connection wirelessly, using the iMac's AirPort, to your PC laptop. However, you will not be able to use wireless security, as the only option available (WEP), for Internet Sharing, will only work with other Macs.
To setup for Internet Sharing (Wired to Wireless):
Enable Software Firewall - iMac
System Preferences > Sharing > Firewall
- Click Stop to start the software firewall
Setup the Network
Cable Modem > (Ethernet cable) > [Ethernet port] iMac > (wireless) > PC laptop
Setup Port Order - iMac
System Preferences > Network > Show > Network Port Configurations
- Verify that "AirPort" and "Built-In Ethernet" are enabled.
- Verify that "Built-In Ethernet" is at the top of the list, followed by "AirPort".
- Click "Apply Now."
Configure the Internet Connection - iMac
System Preferences > Network > Show > Built-In Ethernet > TCP/IP
- Configure IPv4: Using DHCP
- Configure IPv6: Automatically or Off
Enable Internet Sharing - iMac
System Preferences > Sharing > Internet
- Share your connection from: Built-in Ethernet
- To computers using: AirPort (checked) (Note: Uncheck all other entries in the list.)
- AirPort Options
-- Network Name: <anything you want>
-- Channel: Automatic
-- Click OK
- Click Start

Lost connection between ipod and laptop

Hi there,
Not sure if this is a question for ipod or itunes, but here goes.
I recently purchased a 5th gen ipod and installed itunes on my 2 PC's and a PC based laptop. All worked fine.
Now when I connect the USB cable to the laptop, I hear three quick beeps, (not the usual 2 beeps) my ipod starts charging, but I can't see the ipod in itunes.
When I check device manager, there is an entry with a yellow question mark (labelled ipod) which says the driver is not installed. However when I load the itunes CD, the wizard says no drivers found.
My ipod works fine on the 2 other PC's.
I tried system restore but for some reason it fails to go back to any restore points. whether that's part of the problem or a red herring, I haven't a clue.
Can anyone help?
Many thanks
Packard Bell Windows XP Easynote laptop

Could you be more specific like what happened will it not let you log in or not even go to that application be more specific and I will try to help you out

Connecting a desktop computer to the Internet via the Mobile Hotspot?

Hello,
I've looked at the other postings about this but I'm still not having any luck....and I'm not really sure who to call for tech support.
I can connect my laptop to the Hotspot just fine. The desktop computer is another story.
I bought a Medialink wireless adapter and installed it per the provided directions BUT the connection says that is local only. How do I fix that?
I don't know for sure a local connection only doesn't allow me to actually connect to the Internet, right? I currently also have AT&T Internet with a router so is that complicating things? I'm going to drop the AT&T soon but I'd like to have this figured out first.
What do I need to do?
I have absolutely no idea.....
THANK YOU!

A local only connection means you are connected to the device, but the device is not letting you onto the internet. I'd bet that you have a bogus IP Address and your hotspot has not fully authenticated you to use its internet.
Make sure you are disconnected from all networks, reboot the computer and hotspot, then try connecting again. Make sure you are entering the correct credentials to connect to the hotspot.
Chances are good that the wireless adapter that you are using is the problem here. If you were going to contact a support number I would start with them. There might be another way to configure it to play nicely with the Hotspot. Report back to us if you need more help configuring the hotspot. We will need to know the specific model number so that we can provide you with specific steps.

Laptop to Internet via iPhone over Bluetooth?

Has anyone experimented with getting a laptop on the Internet using an iPhone (connected to EDGE) via a Bluetooth link to the laptop?
Thanks
G3s, G4s, G5s & XServe Mac OS X (10.4.3) Non iPhone owner.

I think bluetooth should be upgraded to allow to use
iPhone to connect to the Internet with any laptop
(i.e. Powerbooks or MacBooks), this is the only
feature I am really missing with the iPhone! Do you
think will be any software upgrade or third party
software allowing to do that? Thanks for sharing.
Wireless access from the iPhone is $20 a month. AT&T's unlimited access for laptops is $80 a month, and for other devices (PDAs, Blackberry, etc; the TOS forbids you to use the PDA as a wireless modem for a laptop) is $50 a month. Thus, if the iPhone COULD be used as a modem it would undercut all of the other wireless data services.
Anyway, you wouldn't really want wireless laptop access over EDGE; believe me, I've tried it. If you really need wireless access get a 3G aircard with a separate data plan. It's really worth the price to have DSL speeds over the cellular network.
best,
Larry
Lenovo T-60 Windows XP Pro Intel iMac, Dell Ubuntu Linux

Lost connection of 2 client laptops to internet via LAN on WRT320N wireless-N dual channel router

Similar Messages

Maybe you are looking for