Lost controll of mouse, new folders opening

lost controll of mouse, new folders being created without my imput, different apps opening up without my concent, only way to shut down computer is just to hold power button down as i have no control over mouse to do anything. cant use apple hardware test, wont boot into the hardware test, its as if someone else is controlling my 15` macbook pro, lion, 2011. is this a virus or hardware or software problem. help please!!!! peter

There are several possible causes for this issue. Please take each of the following steps that you haven't already tried until it's resolved. Some may not apply in your case.
1. Follow the instructions in this support article, and also this one, if applicable. A damaged or defective AC adapter could be the cause, even if it's the right kind.
2. Press down all four corners of the trackpad at once and release. If there's any effect, it's likely to be temporary, and in that case the unit must be serviced or replaced.
3. Open the Bluetooth preference pane in System Preferences and delete all pointing devices other than the trackpad, if applicable. Disconnect any USB pointing devices. By a "pointing device," I mean a peripheral that moves the cursor, such as a trackpad, mouse, trackball, or graphics tablet. A plain keyboard is not a pointing device.
4. Start up in safe mode and test, preferably without launching any third-party applications. If you don't have the problem in safe mode, but it comes back when you restart as usual, stop here and post your results. Do the same if you can't start in safe mode. If there was no difference in safe mode, go on to the next step.
5. Reset the System Management Controller.
6. If you're using a Bluetooth trackpad or mouse, investigate potential sources of interference, including USB 3 devices.
7. A swollen battery in a portable computer can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced without delay.
8. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built-in trackpad of a MacBook to behave erratically. If you're using such an adapter, disconnect it and test.
9. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
10. If none of the above applies, or if you have another reason to think that your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
11. Make a "Genius" appointment at an Apple Store to have the machine and/or external trackpad tested.

Similar Messages

Pass control to a new window opens a small window.

I am using the following:
WETargetPath ("rpt", "Name", "My Report", "weWindow=New")
How do I open the new window so that it is in Full Screen mode (maximized). Right now, it opens a small window. On Maximizing the window, the report window still remains small?
Thanks

hi shabirdewji,
i have attached syntax for a new weWindowUtilities function which will address the resizing issue when a New window (not a named window but a new un-named window) is opened. this means that when a New window is opened using the webelements target functions, you can then resize the new window and have no resizing issues.
please note that you need to use the weTargetPathExt function instead of weTargetPath if you want to specify the initial new window size. please see the weSubmitMethods report in the webelements 246 download for an example.
the syntax below will open a new window with a size of 500px X 500px. please see the user guide for more info on the wetargetpathext function.
stringvar item1:= WETargetPathExt ("rpt", "Name", "myreport", "", 500, 500, true, 400, 200, true, true, true, true, true, "");
WESubmit("cw1", "link", "Open Report in New Custom Window", item1, global stringvar fontlink);
please replace your webelements246 > admin > wewindowutilities function with the attached syntax.
thanks,
jamie

Lost all my thumbnails - new tabs open only a blank page. How do I get them back?

The support topic on this question says to look for a "pin" icon in the upper left corner of the browser. I do not show one. Firefox used to just automatically populate my new tabs page with the thumbnails, but it is no longer doing that, and I don't know how to fix it.
I downloaded some freeware that changed a number of browsing options (default browser, added Bing bar without my full knowledge, etc.). Got that all removed but then Firefox wasn't working well, so I had to uninstall/reinstall the program. Now my thumbnails are gone and I can neither get them back nor create new ones.
Help!
Cheers, Dolly

MOST EXCELLENT. Not only did this work, but I was able to do it all very easily AND it brought back all my previously set up thumbnails in the order I had them arranged on the new tab pages! Wonderful.
I will definitely keep these instructions for future reference, but I had already gone in and deleted all apps and extensions that I did not recognize as from Firefox or that I hadn't added myself. So I'm pretty sure I got rid of the pesky malware that caused the problem already. Great links for that task however.
Thank you SO much!!
Cheers, Dolly

Setting to open folders in new folders

Upgraded from SL to Mavricks. In SL, there was a preference to open folders in new folders instead of replacing the current open window. Did that go away as an option in Mavericks?

open folders in new folders
To open folders in new Window? Try Finder/Preferences/General - open folders in... Then control click the folder and you can open it in a new Window.

Every time i click my mouse an ad opens in a new tab. how so i stop it

i have a macbook air, OSX 10.9.5,
WHEN I AM ON THE INTERNET EVERY TIME I CLICK MY MOUSE A NEW TAB OPENS UP WITH VARIOUS DIFFERENT ADS ON IT. HOW DO I STOP THIS FROM HAPPENING?

There is no need to download anything to solve this problem. You may have installed a variant of the "VSearch" ad-injection malware.
Malware is always changing to get around the defenses against it. These instructions are valid as of today, as far as I know. They won't necessarily be valid in the future. Anyone finding this comment a few days or more after it was posted should look for a more recent discussion, or start a new one.
The VSearch malware tries to hide itself by varying the names of the files it installs. To remove it, you must first identify the naming pattern.
Triple-click the line below on this page to select it, then copy the text to the Clipboard by pressing the key combination command-C:
/Library/LaunchDaemons
In the Finder, select
          Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
A folder named "LaunchDaemons" may open. Look inside it for two files with names of the form
          com.something.daemon.plist
and
           com.something.helper.plist
Here something is a variable word, which can be different in each case. So far it has always been a string of letters without punctuation, such as "cloud," "dot," "highway," "submarine," or "trusteddownloads." Sometimes the word is "apple," and then you must be especially careful not to delete the wrong files, because many built-in OS X files have similar names.
If you find these files, leave the LaunchDaemons folder open, and open the following folder in the same way:
/Library/LaunchAgents
In this folder, there may be a file named
          com.something.agent.plist
where the word something is the same as before.
If you feel confident that you've identified the above files, back up all data, then drag just those three files—nothing else—to the Trash. You may be prompted for your administrator login password. Close the Finder windows and restart the computer.
Don't delete the "LaunchAgents" or "LaunchDaemons" folder or anything else inside either one.
The malware is now permanently inactivated, as long as you never reinstall it. You can stop here if you like, or you can remove two remaining components for the sake of completeness.
Open this folder:
/Library/Application Support
If it has a subfolder named just
           something
where something is the same word you saw before, drag that subfolder to the Trash and close the window.
Don't delete the "Application Support" folder or anything else inside it.
Finally, in this folder:
/System/Library/Frameworks
there may an item named exactly
            v.framework
It's actually a folder, though it has a different icon than usual. This item always has the above name. Drag it to the Trash and close the window.
Don't delete the "Frameworks" folder or anything else inside it.
If you didn't find the files or you're not sure about the identification, post what you found.
If in doubt, or if you have no backups, change nothing at all.
The trouble may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow. Never install any software that you downloaded from a bittorrent, or that was downloaded by someone else from an unknown source.
In the Security & Privacy pane of System Preferences, select the General tab. The radio button marked Anywhere should not be selected. If it is, click the lock icon to unlock the settings, then select one of the other buttons. After that, don't ignore a warning that you are about to run or install an application from an unknown developer.
Then, still in System Preferences, open the App Store or Software Update pane and check the box marked
          Install system data files and security updates (OS X 10.10 or later)
or
          Download updates automatically (OS X 10.9 or earlier)
if it's not already checked.

My mouse will not open any files or folders

My mouse will not open any files or folders. I've had to do a hard reboot but nothing changes. The mouse will scroll across the screen but it will not left or right click on anything on my desktop

Hmmm, does the right button also not work?
One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
Reboot, test again.
If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or some USB or Firewire device, or 3rd party add-on, Check System Preferences>Accounts>Login Items window to see if it or something relevant is listed.
Check the System Preferences>Other Row, for 3rd party Pref Panes.
Also look in these if they exist, some are invisible...
/private/var/run/StartupItems
/Library/StartupItems
/System/Library/StartupItems
/System/Library/LaunchDaemons
/Library/LaunchDaemons

What would cause the screen to swith between backgrounds as if it is being controlled remotely? the system had created 7 new folders on it's own.

System is currently switching between mutliple screens without me touching it. The system has created several new folders. The system is performing as if it is being remotely controlled.

How recently did you switch? If it's less than 60 days, then Verizon simply reinstates your previous account. The fact that you were on the EDGE plan and mailed the devices back, and they apparently are somewhere in the system, could cause complications, and it might just work out that you just go back on the same plan and they set you up with the same devices. I'm not sure how it will go - but since you are still being billed for the devices...

USB Hard / Thumb Drives and lost / hidden / duplicate new folders

It seems I can force this problem to happen consistently on multiple MacBooks with different USB storage devices. Her is what happens:
Connect a USB external hard drive or data stick
Open Finder on that device
Create a new folder with keyboard short cut command (CMDShiftN)
quickly type the name of the new folder
THEN the following happens:
two! new folders will appear with the new name
Sometimes an adjacent folder gets renamed to the new name, yet the contents in both folders are the same (which is empty, due to the newly created folder)
if I switch views (from Icon to panes or list), both of the new folders disappear
If I switch back to icon view, both re appear
If I delete one (does not matter which) then both are deleted (sent to trash, thank goodness) including the adjacent folder which had other data in it!
IF I type the new name of the newly made folder real slow, then all seems to work well
I purchased my mac in June 06. This just happened today. I run 10.4.10 with latest firmware. Plugged in a USB 1GB Centon Data Stick.
Two days ago, my buddy, who just bought his MacBook last month, described the same problem. He had an external W.D. USB drive (powered from the Mac). He spent a day creating folders and organizing data. He said every once in a while, it would happen to him, especially on new folders with short names). I thought it was user error, since he was new to the architecture. Ironically, he was sitting next to me when it happened to me today.
What are your thoughts?
Chaplain Dan
US Army (AIRBORNE)
Mesopotamia, Iraq

I have only seen this reported as happening with things on a server, or on an external drive that is formatted for Windows (FAT32). How is your USB drive formatted? If it is not Mac OS Extended, see this thread:
http://discussions.apple.com/thread.jspa?messageID=4036998
It appears to be a Finder bug. You can either live with it, or else copy the files somewhere else then reformat the drive and put them back.
Francine
Francine
Schwieder

Cannot create new folders on desktop. Cannot drag new items onto desktop. Desktop in Finder opens with Terminal. Not sure if this has anything to do with upgrading to Mavericks but I need help if anyone has ideas. Thank you.

I can no longer create new folders on my desktop. The option to do that is now light gray on the drop down menu and can't be selected.
I cannot drag new items onto desktop any longer either.
The Desktop in Finder opens with Terminal.
Folders and items on Desktop open and work normally.
Not sure if this has anything to do with upgrading to Mavericks but I need help if anyone has ideas.
Thank you.

Take these steps if the cursor changes from an arrow to a white "prohibited" symbol when you try to move an icon on the Desktop.
Sometimes the problem may be solved just by logging out or rebooting. Try that first, if you haven't already done it. Otherwise, continue.
Select the icon of your home folder (a house) in the sidebar of a Finder window and open it. The Desktop folder is one of the subfolders. Select it and open the Info window. In the General section of the window, the Kind will be either Folder or something else, such as Anything.
If the Kind is Folder, uncheck the box marked Locked. Close the Info window and test.
If the Kind is not Folder, make sure the Locked box is not checked and that you have Read & Write privileges in the Sharing & Permissions section. Then close the Info window and do as follows.
Back up all data.
Triple-click anywhere in the line below on this page to select it:
xattr -d com.apple.FinderInfo Desktop
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You should get a new line ending in a dollar sign (“$”). Quit Terminal.
Relaunch the Finder.
If the problem is now resolved, and if you use iPhoto, continue.
Quit iPhoto if it's running. Launch it while holding down the option key. It will prompt you to select a library. Choose the one you want to use (not the Desktop folder.)

Random mouse movements and folders open and close unaided

The mouse cursor wanders around the screen, folders open and close by themselves, dashboard opens and closes, etc. Either a bit of malware or a hardware problem?

See if this -> http://www.thesafemac.com/mmg-infected/#remotecontrol - addresses your problem.
Good luck,
Clinton

I can't control my mouse in games [SOLVED]

Hi
I can't control my mouse in games like nexuiz, teeworld, sauerbraten, open arena... My mouse connected at usb and i have a laptop. I'm not using touchpad. Here's my xorg conf:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder62) Tue Mar 24 06:16:11 PST 2009
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "True"
Option "AutoAddDevices" "False"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "glx"
EndSection
Section "ServerFlags"
Option "Xinerama" "0"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Monitor0"
VendorName "Unknown"
ModelName "LPL"
HorizSync 30.0 - 75.0
VertRefresh 60.0
ModeLine "800x600" 40.000 800 840 968 1056 600 601 605 628 +hsync +vsync
ModeLine "640x480" 25.200 640 656 752 800 480 490 492 525 -hsync -vsync
ModeLine "768x576" 34.960 768 792 872 976 576 577 580 597 -hsync +vsync
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 8600M GS"
Option "NoLogo" "True"
Option "TripleBuffer" "True"
Option "OnDemandVBlankInterrupts" "True"
Option "AddARGBGLXVisuals" "True"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
Option "metamodes" "1280x800_60 +0+0; 800x600 +0+0; 640x480 +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
and my xorg.log
X.Org X Server 1.6.1
Release Date: 2009-4-14
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.29-ARCH x86_64
Current Operating System: Linux dragonball 2.6.29-ARCH #1 SMP PREEMPT Fri Apr 17 14:14:28 CEST 2009 x86_64
Build Date: 15 April 2009 11:01:49AM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr 22 15:43:25 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Layout0"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Device0"
(**) |-->Input Device "Keyboard0"
(**) |-->Input Device "Mouse0"
(**) Option "Xinerama" "0"
(==) Automatically adding devices
(==) Automatically enabling devices
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Keyboard0
(WW) Disabling Mouse0
(II) Loader magic: 0x15c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7
(--) PCI: (0@0:1:3) nVidia Corporation MCP67 Co-processor rev 162, Mem @ 0xd0600000/524288
(--) PCI:*(0@2:0:0) nVidia Corporation GeForce 8600M GS rev 161, Mem @ 0xd1000000/16777216, 0xc0000000/268435456, 0xd2000000/33554432, I/O @ 0x00004000/128
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[22] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[23] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) "dri2" will be loaded by default.
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 180.44 Tue Mar 24 06:11:47 PST 2009
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers//nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) NVIDIA dlloader X Driver 180.44 Tue Mar 24 05:51:43 PST 2009
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 02@00:00:0
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "wfb"
(II) LoadModule: "wfb"
(II) Loading /usr/lib/xorg/modules//libwfb.so
(II) Module wfb: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[22] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[23] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Option "NoLogo" "True"
(**) NVIDIA(0): Option "TwinView" "0"
(**) NVIDIA(0): Option "MetaModes" "1280x800_60 +0+0; 800x600 +0+0; 640x480 +0+0"
(**) NVIDIA(0): Option "TripleBuffer" "True"
(**) NVIDIA(0): Option "AddARGBGLXVisuals" "True"
(**) NVIDIA(0): Option "OnDemandVBlankInterrupts" "True"
(**) NVIDIA(0): Enabling RENDER acceleration
(II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) NVIDIA(0): enabled.
(II) NVIDIA(0): NVIDIA GPU GeForce 8600M GS (G86) at PCI:2:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 524288 kBytes
(--) NVIDIA(0): VideoBIOS: 60.86.51.00.33
(II) NVIDIA(0): Detected PCI Express Link width: 16X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce 8600M GS at PCI:2:0:0:
(--) NVIDIA(0): LPL (DFP-0)
(--) NVIDIA(0): LPL (DFP-0): 330.0 MHz maximum pixel clock
(--) NVIDIA(0): LPL (DFP-0): Internal Dual Link LVDS
(II) NVIDIA(0): Assigned Display Device: DFP-0
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "1280x800_60+0+0"
(II) NVIDIA(0): "800x600+0+0"
(II) NVIDIA(0): "640x480+0+0"
(II) NVIDIA(0): Virtual screen size determined to be 1280 x 800
(--) NVIDIA(0): DPI set to (98, 96); computed from "UseEdidDpi" X config
(--) NVIDIA(0): option
(**) NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[22] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[23] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) NVIDIA(0): Initialized GPU GART.
(II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
(II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
(II) NVIDIA(0): configuration option may not be set correctly. When the
(II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
(II) NVIDIA(0): try to use it to receive ACPI event notifications. For
(II) NVIDIA(0): details, please see the "ConnectToAcpid" and
(II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
(II) NVIDIA(0): Config Options in the README.
(II) NVIDIA(0): Setting mode "1280x800_60+0+0"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(==) NVIDIA(0): Disabling shared memory pixmaps
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(**) Option "dpms"
(**) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(II) Loading extension XINERAMA
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing extension GLX
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 2.2.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device AlpsPS/2 ALPS GlidePoint
(**) AlpsPS/2 ALPS GlidePoint: always reports core events
(**) AlpsPS/2 ALPS GlidePoint: Device: "/dev/input/event9"
(II) AlpsPS/2 ALPS GlidePoint: Found 5 mouse buttons
(II) AlpsPS/2 ALPS GlidePoint: Found x and y relative axes
(II) AlpsPS/2 ALPS GlidePoint: Found x and y absolute axes
(II) AlpsPS/2 ALPS GlidePoint: Found absolute touchpad
(II) AlpsPS/2 ALPS GlidePoint: Configuring as touchpad
(**) AlpsPS/2 ALPS GlidePoint: YAxisMapping: buttons 4 and 5
(**) AlpsPS/2 ALPS GlidePoint: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "AlpsPS/2 ALPS GlidePoint" (type: TOUCHPAD)
(**) AlpsPS/2 ALPS GlidePoint: (accel) keeping acceleration scheme 1
(**) AlpsPS/2 ALPS GlidePoint: (accel) filter chain progression: 2.00
(**) AlpsPS/2 ALPS GlidePoint: (accel) filter stage 0: 20.00 ms
(**) AlpsPS/2 ALPS GlidePoint: (accel) set acceleration profile 0
(II) config/hal: Adding input device PS/2 Mouse
(**) PS/2 Mouse: always reports core events
(**) PS/2 Mouse: Device: "/dev/input/event7"
(II) PS/2 Mouse: Found 3 mouse buttons
(II) PS/2 Mouse: Found x and y relative axes
(II) PS/2 Mouse: Configuring as mouse
(**) PS/2 Mouse: YAxisMapping: buttons 4 and 5
(**) PS/2 Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "PS/2 Mouse" (type: MOUSE)
(**) PS/2 Mouse: (accel) keeping acceleration scheme 1
(**) PS/2 Mouse: (accel) filter chain progression: 2.00
(**) PS/2 Mouse: (accel) filter stage 0: 20.00 ms
(**) PS/2 Mouse: (accel) set acceleration profile 0
(II) config/hal: Adding input device A4Tech PS/2+USB Mouse
(**) A4Tech PS/2+USB Mouse: always reports core events
(**) A4Tech PS/2+USB Mouse: Device: "/dev/input/event10"
(II) A4Tech PS/2+USB Mouse: Found 8 mouse buttons
(II) A4Tech PS/2+USB Mouse: Found x and y relative axes
(II) A4Tech PS/2+USB Mouse: Found scroll wheel(s)
(II) A4Tech PS/2+USB Mouse: Configuring as mouse
(**) A4Tech PS/2+USB Mouse: YAxisMapping: buttons 4 and 5
(**) A4Tech PS/2+USB Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "A4Tech PS/2+USB Mouse" (type: MOUSE)
(**) A4Tech PS/2+USB Mouse: (accel) keeping acceleration scheme 1
(**) A4Tech PS/2+USB Mouse: (accel) filter chain progression: 2.00
(**) A4Tech PS/2+USB Mouse: (accel) filter stage 0: 20.00 ms
(**) A4Tech PS/2+USB Mouse: (accel) set acceleration profile 0
(EE) A4Tech PS/2+USB Mouse: Read error: Resource temporarily unavailable
(EE) A4Tech PS/2+USB Mouse: Read error: Resource temporarily unavailable
I searched the forum and find a wiki page about x11 hotplug and i disabled it, not worked, added this;
Section "Module"
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
EndSection
not worked too.
dmesg | grep -i mouse
input: Macintosh mouse button emulation as /devices/virtual/input/input0
mice: PS/2 mouse device common for all mice
input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input7
input: A4Tech PS/2+USB Mouse as /devices/pci0000:00/0000:00:04.0/usb4/4-1/4-1:1.0/input/input10
generic-usb 0003:09DA:000E.0001: input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:04.0-1/input
Thanks, waiting your helps.
Eren
Last edited by eren (2009-04-28 15:27:33)

new xorg log
[goku@dragonball ~]$ cat /var/log/Xorg.0.log
X.Org X Server 1.6.1
Release Date: 2009-4-14
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.29-ARCH x86_64
Current Operating System: Linux dragonball 2.6.29-ARCH #1 SMP PREEMPT Fri Apr 17 14:14:28 CEST 2009 x86_64
Build Date: 15 April 2009 11:01:49AM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Apr 26 01:51:28 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Layout0"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Device0"
(**) |-->Input Device "Keyboard0"
(**) |-->Input Device "Mouse0"
(**) Option "Xinerama" "0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(**) Extension "Composite" is enabled
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Keyboard0
(WW) Disabling Mouse0
(II) Loader magic: 0x15c0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 5.0
X.Org XInput driver : 4.0
X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7
(--) PCI: (0@0:1:3) nVidia Corporation MCP67 Co-processor rev 162, Mem @ 0xd0600000/524288
(--) PCI:*(0@2:0:0) nVidia Corporation G86 [GeForce 8600M GS] rev 161, Mem @ 0xd1000000/16777216, 0xc0000000/268435456, 0xd2000000/33554432, I/O @ 0x00004000/128
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[22] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[23] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) "dri2" will be loaded by default.
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 180.44 Tue Mar 24 06:11:47 PST 2009
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers//nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) NVIDIA dlloader X Driver 180.44 Tue Mar 24 05:51:43 PST 2009
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 02@00:00:0
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "wfb"
(II) LoadModule: "wfb"
(II) Loading /usr/lib/xorg/modules//libwfb.so
(II) Module wfb: vendor="X.Org Foundation"
compiled for 1.6.1, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[22] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[23] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Option "NoLogo" "True"
(**) NVIDIA(0): Option "TwinView" "0"
(**) NVIDIA(0): Option "MetaModes" "1280x800_60 +0+0"
(**) NVIDIA(0): Option "TripleBuffer" "True"
(**) NVIDIA(0): Option "AddARGBGLXVisuals" "True"
(**) NVIDIA(0): Option "OnDemandVBlankInterrupts" "True"
(**) NVIDIA(0): Enabling RENDER acceleration
(II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) NVIDIA(0): enabled.
(II) NVIDIA(0): NVIDIA GPU GeForce 8600M GS (G86) at PCI:2:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 524288 kBytes
(--) NVIDIA(0): VideoBIOS: 60.86.51.00.33
(II) NVIDIA(0): Detected PCI Express Link width: 16X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce 8600M GS at PCI:2:0:0:
(--) NVIDIA(0): LPL (DFP-0)
(--) NVIDIA(0): LPL (DFP-0): 330.0 MHz maximum pixel clock
(--) NVIDIA(0): LPL (DFP-0): Internal Dual Link LVDS
(II) NVIDIA(0): Assigned Display Device: DFP-0
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "1280x800_60+0+0"
(II) NVIDIA(0): Virtual screen size determined to be 1280 x 800
(--) NVIDIA(0): DPI set to (98, 96); computed from "UseEdidDpi" X config
(--) NVIDIA(0): option
(**) NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[17] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[22] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[23] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) NVIDIA(0): Initialized GPU GART.
(II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
(II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
(II) NVIDIA(0): configuration option may not be set correctly. When the
(II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
(II) NVIDIA(0): try to use it to receive ACPI event notifications. For
(II) NVIDIA(0): details, please see the "ConnectToAcpid" and
(II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
(II) NVIDIA(0): Config Options in the README.
(II) NVIDIA(0): Setting mode "1280x800_60+0+0"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(==) NVIDIA(0): Disabling shared memory pixmaps
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(**) Option "dpms"
(**) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(II) Loading extension XINERAMA
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing extension GLX
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.6.0, module version = 2.2.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 4.0
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device AlpsPS/2 ALPS GlidePoint
(**) AlpsPS/2 ALPS GlidePoint: always reports core events
(**) AlpsPS/2 ALPS GlidePoint: Device: "/dev/input/event9"
(II) AlpsPS/2 ALPS GlidePoint: Found 5 mouse buttons
(II) AlpsPS/2 ALPS GlidePoint: Found x and y relative axes
(II) AlpsPS/2 ALPS GlidePoint: Found x and y absolute axes
(II) AlpsPS/2 ALPS GlidePoint: Found absolute touchpad
(II) AlpsPS/2 ALPS GlidePoint: Configuring as touchpad
(**) AlpsPS/2 ALPS GlidePoint: YAxisMapping: buttons 4 and 5
(**) AlpsPS/2 ALPS GlidePoint: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "AlpsPS/2 ALPS GlidePoint" (type: TOUCHPAD)
(**) AlpsPS/2 ALPS GlidePoint: (accel) keeping acceleration scheme 1
(**) AlpsPS/2 ALPS GlidePoint: (accel) filter chain progression: 2.00
(**) AlpsPS/2 ALPS GlidePoint: (accel) filter stage 0: 20.00 ms
(**) AlpsPS/2 ALPS GlidePoint: (accel) set acceleration profile 0
(II) config/hal: Adding input device PS/2 Mouse
(**) PS/2 Mouse: always reports core events
(**) PS/2 Mouse: Device: "/dev/input/event8"
(II) PS/2 Mouse: Found 3 mouse buttons
(II) PS/2 Mouse: Found x and y relative axes
(II) PS/2 Mouse: Configuring as mouse
(**) PS/2 Mouse: YAxisMapping: buttons 4 and 5
(**) PS/2 Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "PS/2 Mouse" (type: MOUSE)
(**) PS/2 Mouse: (accel) keeping acceleration scheme 1
(**) PS/2 Mouse: (accel) filter chain progression: 2.00
(**) PS/2 Mouse: (accel) filter stage 0: 20.00 ms
(**) PS/2 Mouse: (accel) set acceleration profile 0
(II) config/hal: Adding input device A4Tech PS/2+USB Mouse
(**) A4Tech PS/2+USB Mouse: always reports core events
(**) A4Tech PS/2+USB Mouse: Device: "/dev/input/event10"
(II) A4Tech PS/2+USB Mouse: Found 8 mouse buttons
(II) A4Tech PS/2+USB Mouse: Found x and y relative axes
(II) A4Tech PS/2+USB Mouse: Found scroll wheel(s)
(II) A4Tech PS/2+USB Mouse: Configuring as mouse
(**) A4Tech PS/2+USB Mouse: YAxisMapping: buttons 4 and 5
(**) A4Tech PS/2+USB Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "A4Tech PS/2+USB Mouse" (type: MOUSE)
(**) A4Tech PS/2+USB Mouse: (accel) keeping acceleration scheme 1
(**) A4Tech PS/2+USB Mouse: (accel) filter chain progression: 2.00
(**) A4Tech PS/2+USB Mouse: (accel) filter stage 0: 20.00 ms
(**) A4Tech PS/2+USB Mouse: (accel) set acceleration profile 0
(EE) A4Tech PS/2+USB Mouse: Read error: Resource temporarily unavailable
(EE) A4Tech PS/2+USB Mouse: Read error: Resource temporarily unavailable
(EE) A4Tech PS/2+USB Mouse: Read error: Resource temporarily unavailable
and my xorg.conf
[goku@dragonball ~]$ cat /etc/X11/xorg.conf
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder62) Tue Mar 24 06:16:11 PST 2009
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "glx"
EndSection
Section "ServerFlags"
Option "Xinerama" "0"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mouse3"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Monitor0"
VendorName "Unknown"
ModelName "LPL"
HorizSync 30.0 - 75.0
VertRefresh 60.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 8600M GS"
Option "NoLogo" "True"
Option "TripleBuffer" "True"
Option "OnDemandVBlankInterrupts" "True"
Option "AddARGBGLXVisuals" "True"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
Option "metamodes" "1280x800_60 +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
My head gonna explode Btw i wonder this problem comes with hwd may be I can't control it again damn!

Cannot create new folders in Outlook

I just bought a new PC computer. I installed MSFT Office Professional Plus 2010. I opened Outlook and added in (i) the pst folder I had set up from my previous Vista
computer (also with Outlook 2010), (ii) my hotmail account, (iii) my at&t/yahoo account and (iv) my gmail account. I cannot create new folders in any of them.
When I right click anywhere in the navigation pane and select "New Folder..." I get the following error message:
"Outlook cannot read the registry information.
-Close and restart Outlook.
-Reinstall Outlook
-Reinstall Microsoft Exchange or other e-mail system."
I tried all three, including removing and reinstalling Office and removing all of the email accounts/pst files and re-adding and still have the problem.
If I try to right-click properties on any of the accounts, I get the same error message, with the following additional language first:
"Cannot display 'General' page. This page will remain visible, but is not available."
Not sure what is left to try.
Appreciate any ideas.

Hi
Thank you for using
Microsoft Office for IT Professionals Forums.
From your description, If the PC from clean install, you can follow these steps to test this issue.
1.
Start the Outlook in safe mode,
Press and hold the CTRL key,
and then click Outlook.
If the problem does not occur in the safe mode, this issue might be related to some third-party add-ins in the Office program, we can try to disable them.
2.
Create a New profile & PST file to test this issue
If this problem does not occur in the new Outlook profile & PST, the old Outlook profile is corrupted. We can delete that and use a new Outlook profile.
3.
Make sure the HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Office
key permissions to allow full permissions to all users
Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might
occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how
to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756  How
to back up and restore the registry in Windows
a)
Exit Outlook if it is running.
b)
Click
Start, and then click Run. Copy and paste (or type) the following command in the
Open box, and then press ENTER: regedit
c)
Locate and select the following key:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Office
d)
On the
Edit menu, click Permissions.
e)
Click the registry key for the user who is currently logged on, and ensure that
Read and Full Control permissions are both set to
Allow.
f)
Click the Advanced button, ensure that the user who is currently logged on is selected, that
Full Control is listed in the Permissions
column, and that This Key and Subkeys is listed in the
Apply to column.
g)
Click to select the Replace permission entries on all child objects with entries shown here that apply to child objects check box, and clear
the check box
Windows 7: Include inheritable permissions from this
object’s parent
Windows XP: Inherit from parent the permission entries that apply to child objects. Include these with entries explicitly defined here.
h)
When you are prompted to continue, click Remove.
i)
Click Apply, and then click Yes when you are prompted to continue.
j)
Click OK, and then click OK again.
k)
On the Registry menu, click Exit.
Please take your time to try the suggestions and let me know the results at your earliest convenience. If anything is unclear or if there is anything
I can do for you, please feel free to let me know.
Hope that helps.
Sincerely
William Zhou CHNPlease remember to mark the replies as answers if they help and unmark them if they provide no help.

IWork bug won't let me save in new folders

Hi I'd like to know why all my iWork apps won't let me save my files in new locations.
Every time I try to save something it only lets me save my file to the page it automatically shows me (my documents).
When I try to make a new folder within my documents to save my files, it tells me that the folder is a read-only location. See picture here:
When I checked the permissions in the info of my documents, or the subfolder I try to make new folder in, it says that anyone who accesses my computer can read and write. See picture here:
Please let me know how I can resolve this because I find it very hassle at this point to organize my files without this feature. I have already restarted the computer, Repaired and verified disk permissions, updated all the software and nothing seems to be working. The only way I can make new folders is by making one through Finder first, placing it in the right location, and saving my files there.
Thanks

Back up all data before proceeding.
This procedure will unlock all your user files (not system files) and reset their ownership, permissions, and access controls to the default. If you've intentionally set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it, but you do need to follow the instructions below.
Step 1
If you have more than one user, and the one in question is not an administrator, then go to Step 2.
Triple-click anywhere in the following line on this page to select it:
sudo find ~ $TMPDIR.. -exec chflags -h nouchg,nouappnd,noschg,nosappnd {} + -exec chown -h $UID {} + -exec chmod +rw {} + -exec chmod -h -N {} + -type d -exec chmod -h +x {} + 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window by pressing command-V. I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
You'll be prompted for your login password, which won't be displayed when you type it. Type carefully and then press return. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command may take several minutes to run, depending on how many files you have. Wait for a new line ending in a dollar sign ($) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1, if you prefer not to take it, or if it doesn't solve the problem.
Start up in Recovery mode. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open. In that window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window will open. You’re not going to reset a password.
Select your startup volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

HT1349 Can anyone help I have lost my settings app on the opening screened my iPad 2. After re setting factory settings its still not there how can I get it back?

Can anyone help I have lost my SETTINGS app on the opening screen of my iPad and can't find out where to retrieve it. I have re set the factory settings but it did not re-appear. Without this app I can't change any settings. Thanks if anybody can help with idiot guide instructions I would be very grateful.

Hello
Lost mind last week. Remembered a post: impossable to delete this app and one should look in all the folders on the home pages.
Found it in a news folder. So have a look in all of your folders. Hope you haven't to many
Best of luck
Shaun

How to create new folders on iCloud Drive from iOS or with document picker?

Recently I wanted to share several files from my iWorks suite with my colleagues. I do not want them to edit these files, instead I made templates in Numbers for easier management of hours worked. Everyone could download their copy and keep a track of their hours themselves. The problem is, not everyone has an Apple product.
Unfortunately, iOS does not support native browsing of iCloud Drive (except the document picker, which, to me, isn't helpful at all), the only way I know of - to create a new folder - is to open iCloud.com in Safari, request the desktop site and make a new folder from there.
Is there another way of creating new folders, preferably an official app from Apple or from within an iWorks app or the document picker that I do not know of? Or is this actually a missing feature?
Also, if Apple could make an app similar to Microsoft OneDrive, that would be great.

Yes, there is a way. Here is the workaround. You can add notes folders directly with your iPad or iPhone.
http://keeplifesimple.weebly.com/1/post/2013/11/add-folders-to-native-notes-app- on-ios.html
Enjoy! Please pass it on, leave a comment on the page, or "like us" on Facebook if you find this information helpful.

Lost controll of mouse, new folders opening

Similar Messages

Maybe you are looking for