LOST TCP SESSION, LDP AND BGP, OVER ONE INTERFACE

On 7609 PE router, lost only TCP session attach to one interface (Te3/3). The router shows this log
Aug 4   13:17:31.424: %LDP-5-NBRCHG: LDP Neighbor 200.111.117.251:0 (1) is DOWN   (Session KeepAlive Timer expired)
Aug 4   13:19:52.493: %BGP-5-ADJCHANGE: neighbor 200.11.96.126 Down BGP Notification   sent
Aug 4   13:19:52.493: %BGP-3-NOTIFICATION: sent to neighbor 200.11.96.126 4/0 (hold   time expired) 0 bytes
Aug 4   13:42:11.265: %BGP-5-ADJCHANGE: neighbor 200.11.96.126 Up
Aug 4   13:42:23.549: %LDP-5-NBRCHG: LDP Neighbor 200.111.117.251:0 (1) is UP
The device did not present a interface flap.
The device did not present lost of OSPF adyacency, over the same interface
The device did not present lost of TCP session over oher interfaces
Please help me,
I suspect a bug, but I failed to find
Christian

Hi Nagendra
This is output og sh tcp brief
PE2-PCS-RANCAGUA#sh tcp brief
TCB       Local Address               Foreign Address             (state)
4B558124 200.11.98.9.646             200.11.98.37.51654          ESTAB
53336910 200.11.98.9.646             200.111.117.61.49833        ESTAB
4B4CF2A0 200.11.98.9.646             200.111.117.20.64138        ESTAB
536E56A4 200.11.98.9.61369           200.11.96.126.179           ESTAB
53359454 200.11.98.9.22913           200.11.96.81.646            ESTAB
4B6C25EC 200.11.98.9.646             200.111.117.251.53802       ESTAB
537CFBE4 200.11.98.9.62975           200.11.96.125.179           ESTAB
5330A774 200.11.98.9.646             200.111.117.86.62367        ESTAB
4B4D97EC 200.11.98.9.18753           200.11.96.88.646            ESTAB
4B018A28 200.11.98.9.61292           200.11.98.8.646             ESTAB
4B0B176C 200.11.98.9.23              190.151.64.218.36508        ESTAB
4B1976F0 200.11.98.9.17760           190.151.97.92.646           ESTAB
4B261BD0 200.11.98.9.646             200.72.146.42.64641         ESTAB
537CEFF8 200.11.98.9.646             200.111.117.74.54785        ESTAB
531F4890 200.11.98.9.15536           190.151.97.77.646           ESTAB
5359F5B4 200.11.98.9.24658           190.151.97.74.646           ESTAB
PE2-PCS-RANCAGUA#
Christian

Similar Messages

HT3406 what if i lost my original sim, and couldnt secure one? can't it be activated without sim?

what if i lost my original sim, and couldnt secure one? can't it be activated without sim? i updated to 5.1.1

can i restore the iphone to backups with out the need of the carrier sim?

How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

Hi ,
Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA outside interface .
Accordingly you can configure NAT
HTH
Sandy .

Collecting and Bundling Messages - One Interface

Hi ,
I am trying this Collecting and Bundling Messages - One Interface my interface is File .
Followed all the steps in the SAP documentation under Examples and Usage cases.
But I get only one message from the inbound channel .
when I check the Mapping in the MONI . It shows 2 instances of interface in the MessageIn but the output message of the BPE moni shows only 1 message . Message that is in the first instance of the Mapping IN .
Is it error in the multi mapping ? can some body through some light on this ..
Regards,
KLK

Hi Behaves & Moor,
S, I am trying the pattren given by SAP . Following the weblink given by Mr.Moorty.
I made source and Target Msg type as 0.. Unbound and Multiline for Transformation step.
But when I test the mapping in the Design time by importing a XML with following structure (Please dont mind bad syntax)
<Messages >
   <ns0:Message1>
      <Filesender_MT >
         <Record>
            <Row>
               <ID>1</ID>
            </Row>
         </Record>
      </ns1:Filesender_MT>
   <Message1>
   <Message2>
    <Filesender_MT >
         <Record>
            <Row>
               <ID>2</ID>
             </Row>
         </Record>
      <Filesender_MT>
   <Message2>
</Messages>
I get only one message :
<Messages >
   <ns0:Message1>
      <Filesender_MT >
         <Record>
            <Row>
               <ID>1</ID>
            </Row>
         </Record>
      </ns1:Filesender_MT>
   <Message1>
<Messages>
which is wht i am getting from the inbound CC.
how do I test Multi Mapping ? and when I check the MONI->PE --> Technical Details --> Mapping --> MappingIN
It shows 1 entry but the nestted table shows both the file contents that I have put in the Sender Communication channel.
I am putting 2 files in the Sender CC and expecting these two file contents to Merge and give me 1 file as out put . this is the scenario understood from the SAP documentation please correct me if I am wrong .
Thanks and Regards
K.L.K

How to provied Redundancy for VRF MGMT with help of BGP over MPLS(MPBGP)

Hi,
Please find the Network Topology.
This is One Remote site and mamaged by Mgmt office.
All devices on remote site is accessed by MGMT Office. My organisation seek for Redundancy for Managing devices.
My administration is from MGW to R1. I am new to MPLS.
AS u can see in diagram, R1 have 3 VRF(Voice,Signal and MGMT).Currently i have primary link over whitch we are running MPBGP.
Traffic from these VRF goes to this primary link. Currently Secondary link is not connected.
Now my organisation proposed for the secondary link and they want that only traffic from VRF -- MGMT should go through MPLS RTR R2 (the secondary link ) , when the mgmt routes not learned from MPLS RTR R1 (Connected to the SP1 ).
Current R1 config
There is IBGP betweem R1 to both MPLS RTR.
BGP Config
router bgp 64513
synchronization disable
neighbor 10.36.150.1 remote-as 64513
neighbor 10.36.150.1 activate
neighbor 10.36.150.1 update-source loopback1
address-family ipv4 vrf signalling
    redistribute connected
    redistribute static
$
address-family ipv4 vrf voice
    redistribute connected
    redistribute static
$
address-family ipv4 vrf OAM-T
    redistribute connected
    redistribute static
$
address-family vpnv4
    neighbor 10.36.150.1 activate
    neighbor 10.36.150.1 send-community
$
!<ospfv2>
router ospf 100
interface gei-3/3
    network point-to-point
$
network 10.36.150.49 0.0.0.0 area 0.0.0.0 --- loopback ip (Configured)
network 10.36.149.60 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R1.(Configured)
network 10.36.149.64 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R2. ---------- (till now not configured as secondary link is not connected)
router-id 10.36.150.49
so what configuration need to done at R1 to achiev the redunancy for MGMT vrf ?
if possible please reply with sample configuration.
or
IN MPBGP protocol, where i will apply routing policy to apply as- path prepand    so that Route would be secondary to neighbor.
IGP-OSPF and BGP over MPLS is running.
on Which address-familiy nbr,should i apply, is it in VPNV4 or IPV4 or IPV4 VRF ?
if i want 10.36.128.0/26 prefix should go to Neigbhor MPLS R2, what should i use access-list or Prefix list?
please provide the reply with its config .
thanks in advance,
Regards,
Ajay
Message was edited by: Ajaykumar yadav

Hi,
Please find the Network Topology.
This is One Remote site and mamaged by Mgmt office.
All devices on remote site is accessed by MGMT Office. My organisation seek for Redundancy for Managing devices.
My administration is from MGW to R1. I am new to MPLS.
AS u can see in diagram, R1 have 3 VRF(Voice,Signal and MGMT).Currently i have primary link over whitch we are running MPBGP.
Traffic from these VRF goes to this primary link. Currently Secondary link is not connected.
Now my organisation proposed for the secondary link and they want that only traffic from VRF -- MGMT should go through MPLS RTR R2 (the secondary link ) , when the mgmt routes not learned from MPLS RTR R1 (Connected to the SP1 ).
Current R1 config
There is IBGP betweem R1 to both MPLS RTR.
BGP Config
router bgp 64513
synchronization disable
neighbor 10.36.150.1 remote-as 64513
neighbor 10.36.150.1 activate
neighbor 10.36.150.1 update-source loopback1
address-family ipv4 vrf signalling
    redistribute connected
    redistribute static
$
address-family ipv4 vrf voice
    redistribute connected
    redistribute static
$
address-family ipv4 vrf OAM-T
    redistribute connected
    redistribute static
$
address-family vpnv4
    neighbor 10.36.150.1 activate
    neighbor 10.36.150.1 send-community
$
!<ospfv2>
router ospf 100
interface gei-3/3
    network point-to-point
$
network 10.36.150.49 0.0.0.0 area 0.0.0.0 --- loopback ip (Configured)
network 10.36.149.60 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R1.(Configured)
network 10.36.149.64 0.0.0.3 area 0.0.0.0 ---- p2p ip bet R1 and MPLS R2. ---------- (till now not configured as secondary link is not connected)
router-id 10.36.150.49
so what configuration need to done at R1 to achiev the redunancy for MGMT vrf ?
if possible please reply with sample configuration.
or
IN MPBGP protocol, where i will apply routing policy to apply as- path prepand    so that Route would be secondary to neighbor.
IGP-OSPF and BGP over MPLS is running.
on Which address-familiy nbr,should i apply, is it in VPNV4 or IPV4 or IPV4 VRF ?
if i want 10.36.128.0/26 prefix should go to Neigbhor MPLS R2, what should i use access-list or Prefix list?
please provide the reply with its config .
thanks in advance,
Regards,
Ajay
Message was edited by: Ajaykumar yadav

Why not jdeveloper creates the persistance unit and the session client and

why you do not create the persistance unit (outside) and the session client and ...the interface and other required opjects automatically when I create the application or the project?
why you are using symbols like AFD, JSF, JSP, JPA,.JEE...and tens more, why you do not use a meaningfull names of these process symbols.
Thanks
Ali

Asalman,
I'm quite happy the JDeveloper behaves the way it does. Why? Because in most of my scenarios I don't want to be driven in a particular direction of development. This my choice of development and I don't like tools that dictate this to me.
--olaf

How to make VPN TCP session stateful?

I found if I set up interface rules for VPN, even from higer security level interface to lower security level interface, the TCP session is not stateful. I have to open relative ports on both interface. Is there anyway can make VPN connection TCP session stateful, just like using normal interfaces (like with out VPN?) ? Thanks!

here is the configuration on PIX,
group-policy DfltGrpPolicy attributes
wins-server value 10.0.0.67 10.0.0.68
dns-server value 10.0.0.67 10.0.0.68
vpn-simultaneous-logins 20
vpn-idle-timeout 5
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn-acl
default-domain value mydomain.com
address-pools value vpnpool group-policy DfltGrpPolicy attributes
wins-server value 10.0.0.67 10.0.0.68
dns-server value 10.0.0.67 10.0.0.68
vpn-simultaneous-logins 20
vpn-idle-timeout 5
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn-acl
default-domain value want-want.com
address-pools value vpnpool

Application Manager and the wanted language interface

I am a very oldtimer with Adobe and Photoshop. I was brought up in the States and Worked for US Corp's. Before CS6 I always installed an English Interface. Now, Adobe application Mgr is in French eventhough I requested and insisted in using the US connections from start! How can I get a US version running? The CS6 is in French and only offers one interface in the pulldown menus (preferences). My Lightroom is in English and I want everything in English.Thanks PdeRumine

Which operating system are you using? Also you can check the language selection in the Adobe Application Manager. If you click on your name and go to Preferences there will be an option to choose your language there.
This may not resolve your issue though which is why I need to know which operating system you are using before giving any additional instructions.

I can only open one PDF in session. If I try to open a different one, I get the same as before. The only way to see a different PDF is to close the browser and start over. A bit hassle with sites requiring a password.

Many web sites have links to multiple PDF files. I have no trouble reading the first PDF file, but if I try to open a different one, I always get the first one I opened. Firefox ignores the other links and goes back to the first one. The only remedy seems to be to close Firefox and start over again. This is a hassle for sites requiring a username and password to enter. What's wrong here?

Do you have Adobe Reader X or Adobe Reader 9.something?
I think this is a problem with the newest version of Adobe Reader which came out about 5-6 days ago.

I lost my iPod touch and now have a new one. Is there a way to transfer all the songs on have in iTunes onto the new iPod?

I lost my iPod touch and bought a new one? Is there a way to transfer all the songs I have in iTunes onto the new iPod? I am scared I will lose it all when I sync the new one or that I have to start all over. Please help!!

You can do better than that. You can click on the Restore button that appears under your device in iTunes. This will restore your iPod to factory settings as if it were fresh out of the box. But don't worry. By doing a restore, you will then be given the option to "Restore from Backup." This will allow you to restore the state of your previous iPod!!

Work is lost after illustrator freezes and then crashes when copying over to photoshop

work is lost after illustrator freezes and then crashes when copying items over to photoshop, then when re-opening the illustrator file it gets to the end of reading the file to open then quits again? this keeps happening!

afrill,
It seems that you file has become corrupted.
One thing often tried first is to create a new document and File>Place the corrupted one to see how much may be rescued that way.
Here is a website where you can see whether it can rescue the file, and if it can, you may pay for a subscription to have it done,
http://www.recoverytoolbox.com/buy_illustrator.html
and another similar website,
http://markzware.com/adobe-software/fix-illustrator-file-unknown-error -occurred-pdf2dtp-file-recovery/
As far as I remember, the former is for Win and the latter for Mac.
Here are a few pages about struggling with it yourself:
http://daxxter.wordpress.com/2009/04/16/how-to-recover-a-corrupted-ill ustrator-ai-file/
http://helpx.adobe.com/illustrator/kb/troubleshoot-damaged-illustrator -files.html
http://kb2.adobe.com/cps/500/cpsid_50032.html
http://kb2.adobe.com/cps/500/cpsid_50031.html

Session method and call transaction methos which one is the sap recomonded

hi
PLease give me the answer to these questions.
session method and call transaction methos which one is the sap recomonded why .
2) if we want to maintain BDC program in all the systems.wt to d0

Hi Revethi,
Here is the difference between the Session and Call Transaction method.
Session
Session method supports both small amount of data aswell as large amount of data
2) data processing is asynchronus and data updation is synchronus.
3) it process multiple apllication while perfomaning validations.
4) in session method data will be updated in data base only after processing session only.
5) system provide by default logfile for handling error records.
6) it supports both foreground aswell as background process
in bdc we use FM ... bdc_open_group " for creating Session
bdc_insert " adding transaction and bdcdata table for updating database
bdc_close_group " for closing Session
Call Transaction
Call transaction exclusively for small amout of data
2) it supports only one apllication while perfoming validations
3) there is no default logfile, We can explicitly provide logic for creating logfile for handling error records.
we can create logfile by using structure....BDCMSGCOLL
4) it doesn't support background processing.
5) data processing is synchronous and Data updation is Synchronous( default), in
this method also supports daya updation in asynchronus process also.
Syntax:
Call transaction <transaction-name> using BDCDATA
mode <A/N/E> update <L/A/S>
messages into BDCMSGCOLL.

I own a ipod touch and a ipad but i lost my ipod touch and downloaded the find iphone app on my ipad and when i opened the app my ipod touch wasnt even listed on it as one of my products but i use the same apple id for all of my products??!! Please Help

i own a ipod touch and a ipad2g but i lost my ipod touch and downloaded the find iphone app on my ipad and when i opened the app my ipod touch wasnt even listed on it as one of my products but i use the same apple id for all of my products??!! Please Help

Ive never used that but I think there is a find ipod app. But im not sure. The ipod might have had to have it on?

My macbook pro recently got swiped and I lost all my data, problem is, just before it was swiped I set up my new iphone 5 which transferred all my photos and music over which is no longer on the computer. What will happen to my phone if I plug it in?

My macbook pro recently got swiped and I lost all my data, problem is, just before it was swiped I set up my new iphone 5 which transferred all my photos and music over which is no longer on the computer. What will happen to my phone if I plug it in?

I never used icloud before so there is no data to back up from. I just spoke to the apple store and they said that if I do plug it in, all the data will be swiped....is there a program I can use to transfer my data from my phone to computer without loosing it all ???
Renee

My ipad has gone in lost mode by mistake and now i have it and i enter the password and i cant enter my ipad how can i enter or restart the ipad and start back over new

my ipad has gone in lost mode by mistake and now i have it and i enter the password and i cant enter my ipad how can i enter or restart the ipad and start back over new

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.

LOST TCP SESSION, LDP AND BGP, OVER ONE INTERFACE

Similar Messages

Maybe you are looking for