Lot creation with physical sample

Hi all,
Inspection lots with physical sample not getting created.Error message "Origin 15 not defined" pops up constantly with all materials.The settings in SPRO are maintained:
LO:15
Origin:15
Variant :01
Inspection type:15
Settings in material master: Activated inspection type '15'
No lots with physical samples exist for the material.
Regards
Binesh

I just want to check that you are using the inspection type 15 correctly.  That is used to create inspection lots (usually manually), for already exisitng physical samples in your inventory.  I.e. usuaully this is used to recheck an old sample after a customer complaint or to check shelf life or stability sample.
So the the physical samples have to be created first.  Do you have physical samples created?
You can manually create them but they are usually automatically created via the 01 and 04 lots that use a physical sample-drawing procedure and approporate inspection plans.
FF

Similar Messages

  • Lot Type 15 - Physical Samples

    Gang,
    Can someone please help me. I am trying to set up a Sandbox of Vanilla SAP.
    I have most of the initial configuration done, so I started messing around with the data.
    I have a Material that I extended the QM view to. I added Inspection Type 15 - Physical Samples to the View. There is NO selection for Inspect with Task List....There is ONLY a selection for Inspect with Material Spec.
    Can someone explain this? I want to create an Inspection Lot from a Physical Sample using transaction QPR5. But I have an Inspection plan I'd like to use.  Why can't I use Inspection Plans??
    Thanks so much

    Are you sure that it isn't just greyed out?  In the system I'm looking at the "Insp. with task list" is ticked on and greyed out.  The "Insp with mat spec." is available to use if desired.
    For physical samples you should be specifying a sample drawing procedure and you can only do that if you use an inspection plan.
    FF

  • QM _Inspection Lot Creation with Move ment type-542

    Dear All,
    The Business Scenario is when ever goods received from  Sub contracting vendor with out any processing by 542 movement type the system should create the Inspection lot automatically.
    How can achive this function?
    Your inputs are valuable.
    Regards,
    Manis

    IMG - Quality management - Quality Inspection - Inspection lot creation - Inspection for goods movements..
    You have to add new entry for movement type 542..
    complete help is available there..
    Also you have to activate the related inspection type in QM view in material master.
    You can try this in development server. (I am also not an expert in this area).
    Regards,
    Amol

  • Three Physical Samples withdraw from inspection lot 04  and then result record for all three

    Dear Gurus,
    We have 3 quality labs and each lab is sent a separate samples to inspect certain characteristics once we receive material from production. I have created an inspection plan and mapped these three labs as  work center in operation and then assigned MICs under each operation to inspect.
    Now my issue is how to map separate 3 samples to inspection lot generated from production  ( type-4) and also how to configure that to inspection plan.
    I have to result record for all these three physical sample as withdrawn from Lot based upon inspection plan as mentioned above.
    I can mention sample drawing procedure in inspection plan but how to map actual sample there.
    Any help will be greatly appreciated.
    Regards,
    Satish

    Hi Satish
    You are creating three operation for depicting three testing Labs.
    Against each lab (operation) you had assigned MICs as per your requirement.
    Now you have to assign a SDP along with inspection point type 200 for physical sample in task list.
    After prod confirmation system will create inspection lot along with a sample by default for 1st operation.
    For other operations you have to create samples manually referring the same inspection lot (QPR6).Remember to click ' Create Insp points' and mention operation.
    Release the samples in QPR4.
    Now when you go for result recording system would ask first for operation, so select the operation , then system will ask for insp point (sample no).There click on assign insp point , so system will provide the Sample no which were created in QPR6 for that particular operation.
    Please follow the steps and revert.
    Regards
    D Mohanty

  • What is the Relation between Inspection Lot, Physical Sample .....

    Hi All,
    I want to know the unique relation between Inpection Lot Number, Physical sample Number, Material Number and Warehouse Number(from LQUA ).
    I have Inspection Lot Number and Physical Sample Number on my selection screen.
    Based on this I have to fetch the details from LQUA.
    I got combination of Lot and sample from the View QAPP_QALS. There is material also in it.
    But I am not understanding how to get the details from LQUA.
    Thanks,
    Bhupal

    Hi Bhupal,
    Just a suggestion, you might consider moving your qns to MM forum, Mr. Jurgen should be able to provide the exact inputs your looking for.
    Regards,
    Vivek

  • Assign physical sample type to lot origin or inspection type

    Something is driving me crazy. I now for 100% that it's possible to change the physical sample type for the lot origin or inspection type. But i can't find the setting in customizing... Can anybody please help me!!!

    No stab studies. There are physical sample types. The physical sample types are assigned to lot origins or inspection types. When you create an inspection lot the correct physical sample type is selected according to this setting...

  • Mapping Physical Sample Quantity - Inspection Plan Characteristics Quantity

    Hello,
    There is a requirment to map Physical Sample Quantity QPRS-MENGE (Size of the Physical Sample) with PLMK-PRUEFEINH (Sample Quantity Factor for Sample(Mult. Sample Unit of Msr.)) based upon Inspection Lot.
    Thanks and Regards,
    Prabhjot Singh
    Moderator message: OK, so please start working on your requirement.
    Edited by: Thomas Zloch on Apr 1, 2011 1:56 PM

    why can't we use Physical sample drawing process (T.code:QPV2 ) for auto creation of physical samples.

  • Display of Qual Characteristics in QE03 for Physical Samples

    Hi All,
    I am using result recording with physical samples.
    I am able to record Qualitative characteristics through transaction QE01. When i want see these "qualitative characteristics" in QE03 screen, just an icon appears in the "results" coulmn in RR screen. (Code & Code Texts missing)
    Why is this so?? When I go back & see in QE01, I can see the Qual Values.
    Require some pointers to address this issue.
    Thank you a lot in advance
    Regards,
    Pradeep

    Hello,
    You may need to check QE13 to view the qualitative results for the inspection point.
    Regards,
    John

  • Availability of Standard Physical Sample Report

    QPR3 Tcode provides Physical Sample details for only one Inspection Lot at a time
    Instead I need below details
    Input Data :
    Material                From     To
    Batch               From     To
    Plant               From     To
    Inspection Lot          From     To
    Physical Sample Number     From     To
    Sample-Drawing Number     From     To
    Sample Category          From     To
    System status          From     To     (Internal Status of Physical-Sample Record)
    Physical Sample Release Date     From     To
    QM mat. auth.          From     To
    Creation Date of Physic Sample     From     To
    Output :
    1) Material No
    2) Material name
    3) Batch
    4) Inspection Lot
    5) Physical Sample No
    6) Plant
    7) Sample Category
    8) Status (Internal Status of Physical-Sample Record)
    9) Vendor ( No & Name )
    10) Manufacturer ( No & Name )
    12) Drawing number
    13) Created by
    14) Creation Date of Physical Sample
    15) Released By
    16) Physical Sample Release Date
    17) Time of Physical Sample Release
    18) Sample Quantity
    19) Unit of Measure for Physical Sample Size
    20) Sample-Drawing Procedure
    21) QM mat. auth.
    22) Insp. Lot Qty
    23) SampleSize
    24) No. Containers
    25) Lot Cntnr.
    26) Group
    27) Group Counter
    28) System Status ( Inspection Lot )
    Is there any provision for accessing same above details via SAP Standard Report
    Kunal Sheth

    Get Solved

  • How to manage physical sample in SAP?

    Hi,
    How to manage physical sample in SAP?
    Regards
    Ashish Jain

    Hi
    Physical sample is to keep the sample of a product till its shelf life expiry date. E.g. In case of any shelf life applicable product, the inspected sample will be retained till its expiry date. If any customer complaints are received, on inspecting the complaint, result may be compared with the existing physical sample.
    In SAP, Material master should have inspection type 15.
    To create physical sample, sample drawing procedure has to be created and attached to the header of inspection plan. With this set up when the lot is created, physical sample will also be created. Result recording should be done for physical sample. Physical sample storage information has to be updated through transaction code QPR2
    Regards
    Nikhilesh Ray

  • Inspection of physical samples

    Hi,
    I am trying to set up quality inspection of physical samples for a plant. Until now we don't use SAP QM for inspection in production really (neither inspection lot origin 03, nor 04) but that might change in near future. Nevertheless, we would like to start with inspection of physical samples.
    As far as I understand the SAP Help files there are "two" different inspection lots for which I can enter values. First, the lot from which a physical sample drawing was created by the system when I create the lot (in my case insp. lot origin 89 and inspection points for physical samples in inspection plan) and, second, the inspection lots I can create from the physical sample via QPR2 or QPR5 (in my case insp. lot origin 15). Although it's one step more for the users to create an inspection lot for each physical sample, I prefer the second option because a physical sample can be reworked in our plant if the results recorded are not acceptable and results have to be recorded again after rework. If I choose the second option I have an inspection lot (origin 89) I can use later on for results recording during production. The fact that irritates me is that's a lot with inspections points of type "physical sample" that I do not need necessarily in all operations.
    Why are there two lots in which results to physical samples can be recorded?
    Do you agree with my solution or are there other more reasonable ways?
    Cheers
    Marcus.

    Hi,
    I am trying to set up quality inspection of physical samples for a plant. Until now we don't use SAP QM for inspection in production really (neither inspection lot origin 03, nor 04) but that might change in near future. Nevertheless, we would like to start with inspection of physical samples.
    As far as I understand the SAP Help files there are "two" different inspection lots for which I can enter values. First, the lot from which a physical sample drawing was created by the system when I create the lot (in my case insp. lot origin 89 and inspection points for physical samples in inspection plan) and, second, the inspection lots I can create from the physical sample via QPR2 or QPR5 (in my case insp. lot origin 15). Although it's one step more for the users to create an inspection lot for each physical sample, I prefer the second option because a physical sample can be reworked in our plant if the results recorded are not acceptable and results have to be recorded again after rework. If I choose the second option I have an inspection lot (origin 89) I can use later on for results recording during production. The fact that irritates me is that's a lot with inspections points of type "physical sample" that I do not need necessarily in all operations.
    Why are there two lots in which results to physical samples can be recorded?
    Do you agree with my solution or are there other more reasonable ways?
    Cheers
    Marcus.

  • Print against new physical sample

    Dear All
    We have created a inspection plan with physical sample and inspection point 200, accordingly we have assigned sampling procedure.
    Initiallly when inspection lot creates with 04, analyst performs the physical sample and same is congirms through QPR4 tcode, Now suppose after analysis the batch is failing and as per the define procedure analyst need to take the fresh sample and do the fresh testing and RR.
    In this case we are creatin a new physical drawing number and RR performing against the new number.
    Now my user wants both the results .....
    1. First result with rejected and
    2. Secong result with rejected or accepted
    How can i get it ???
    AYK

    can anybody answer this question?
    AYK

  • Early lot creation

    Dear Gurus,
    When working with early lot creation, with batch management activated, if I received a partial quantity from an order, it is posted normally to quality, then I make the UD for this lot and it is closed, then if I receive another quantity from the order, it goes unrestricted and do not create a new inspection lot !!!!
    Is that normal or there is problem? If normal how can I overcome this?
    Regards,
    MaX

    Dear it is standard procedure system is behaving correct only.
    if you want every time stock you do GR for order stock should be posted to QI then in MM QM view keep inspection type control as "each order,batch and storage location" means for 1 order if production do multiple confirmation ( N times) system create only one inspection lot and all the confirmation stock updated to the same inspection lot.
    Cheers
    KK

  • Inspection lot creation during GR with respect to Purchase Order

    Dear Experts,
    Here is my Question
    Inspection lot creation during GR with respect to Purchase Order
    Inspection type 01 set in the material master
    inspection lot will be created during GR for a Purchase order
    from my understanding for every GR a inspection lot will be created
    No batch Management
    but the requirement is irrespective to GR qty and number of times of GR
    we need inspection only one inspection lot
    For Instance
    There is a PO for 1000 kg no batch management
    now i do GR for 100 kg for 10 times with different dates
    now i need to have only one inspection lot
    not 10 inspection lot for each 100 kg
    can any one suggest a solution, please advise my understanding is correct
    Many thanks
    Raj

    Dear Raju,
    There is a solution for that .The setting can be done two ways, either in the material master or in the configuration
    1) Material Master
    MM02> QM View> Inspection Setup> 01> Control Insplot> 'X' An inspection lot for each purchase order item/order item 0r  An inspection lot for each material document and material
    a) 'X' An inspection lot for each purchase order item/order item
    This Means
    This setting is limited for use with the inspection lot origins 01 and 04.
    An inspection lot is only created during the first goods receipt for each PO item or production order.
    b) '1' An inspection lot for each material document and material
    If you set this indicator, the system creates only one inspection lot for a material document (in a goods receipt transaction) for each material. This setting is useful, if several purchase orders or partial deliveries are processed for the same material in a goods receipt transaction.
    2) You can do this default in the config
    SPRO > Quality Management >  Quality Inspection > Inspection lot creation >  Define Default values for inspection type > 01> Control Insp lot
    Hope this helps
    Regards
    gajesh

  • Is there any Bapi for Physical Sample creation

    Hi Folks,
    Is there any Bapi for physical sample creation. My scenario is like this I have the data in the table (material, plant, batch, type,vendor, vendorbatch ). For each material i have to create a  physical sample......
    Any ideas or suggestions would be appreciated..
    thanks
    chaithanya.

    HI Chaitanya,
    You can use : BAPI_BATCH_CREATE
    it has import paramaters like Material, Plant , batch , Batch Attributes ( Vendor No, Vendor Batch etc)... I guess this is what you are looking for.
    Regards,
    -Venkat.

Maybe you are looking for