Lots of Problems
I have been having quite a few problems with my Satellite A355D.
First of all my problems started with my battery not recharging. Whenever I plug in the battery I get a "Plugged in not charging message", and the battery stays at 0%. I called Toshiba and they said to replace the battery. I did that, and it worked for about 4 days, and then the same problem.
I did everything short of replacing the jack that is in the computer (i.e. updated drivers - which there was no update for, uninstalled and reinstalled drivers, updating BIOS - which there was no update for).
Now I am at the point where I just figures I will not be able to use the laptop without it being plugged in since the warrenty is out and I can't pay to attempt to fix the problem by replacing the job on the motherboard (Which I read does not alway fix it).
Now I am having a problem where I get a blue screen when I have the computer connected to an external display device (i.e. my TV connected the the SVideo jack). It will run about 30 minutes, freeze for about a minute, then go to the blue screen. Again I tried updating the video driver which there hasn't been an update to the version that I have already, and I installed the patch.
My question is, can any of these problems really be resolved by upgrading to Windows 7? I have heard that it might help since it is most likely driver OS issues that have been resolved through Windows 7.
Any advice will be very much welcomes. I have had this computer a little over a year, and have had more problems with it than I did my old Gateway laptop (This should not be!!!)
Difficult to say for sure. To shut it off unplug the AC Adapter, remove the battery, then press the Power button and hold it for at least 30 seconds. Now see if it turns on and off like it should.
We need to ascertain if you have some hardware problems or not. To check the ram you need to download the Memtest CD Iso, create the CD using the Burn From Image option, then boot to it and allow it to run through a minimum of 3 complete passes. If it shows ANY errors whatsoever then you have defective ram.
To test the hard drive determine what brand of hard drive you have. You can check the Bios/Setup to find out or run SIW or Belarc Advisor. Go to that manufacturer's support site and download their Self Booting Diagnostic CD ISO image, create the CD using the Burn From Image option (see http://iso.snoekonline.com/iso.htm for more information on doing this), then boot to it and run the most exhaustive tests available. If you have a Toshiba drive you will need to use the Hitachi Drive Fitness Test as Toshiba doesn't supply their own.
If you don't post your COMPLETE model number it's very difficult to assist you. Please try to post in complete sentences with punctuation, capitals, and correct spelling. Toshiba does NOT provide any direct support in these forums. All support is User to User in their spare time.
Similar Messages
-
As mentioned above I have just downloaded OSX Maverick to my iMac. I am now having a lot of problems with iCloud. I get the message that "This iMac can't connect to iCloud because of a problem with, and then it goes on to quote my e-mail address. It then says to open iCloud preferences to fix this problem.
I do this and no matter what I seem to do this message continues to return.
Can anybody explain how to resolve this problem (please bear in mind that I am noy very computer literate).
Many thanks
MikeHello John
Sorry I haven't got back to you sooner.
Thanks very much for your help, your solution solved my problem.
Thanks again and kind regards
Mike -
A lot of problems after installing Windows XP using Boot Camp on a Mac Book
I have been having a lot of problems after installing Windows XP Home Edition (2002).
For one, after installing Windows using Boot Camp with Mac OS X 10.5.1, I opened Windows on my Mac Book, inserted the Mac OS X Disk 1 as in the instructions and got the message: +"This package requires a newer version of the Windows installer. Do you want to update the version of the Windows Installer on your system?"+ When I clicked Yes (I had NO idea what it meant at the time), I got the message: "The required resource 'UPDATE' is missing" and the Installer quit.
How do I fix this problem?
Another problem I have is that there is no sound on the Windows XP, yet it works perfectly on Mac OS X. Is there any way to fix this problem?
A third problem I have is that I can't wirelessly connect to the internet using Window XP, yet I can on Mac OS X. I have no idea on how to fix this, and it's really messing with me. D:<
D: There are way too many problems, and I have a feeling there will be a lot more later on. Help....
~Twilight---I'm moving this topic to the Boot Camp forums.
-Twilight -
I need advise and help with this problem .
First , I have been with Mac for many years ( 14 to be exact ) I do have some knowledge and understanding of Apple product .
At the present time I'm having lots of problems with the router so I was looking in to some info , and come across one web site regarding : port forwarding , IP addresses .
In my frustration , amongst lots of open web pages tutorials and other useless information , I come across innocent looking link and software to installed called Genieo , which suppose to help with any router .
Software ask for permission to install , and about 30 % in , my instinct was telling me , there is something not right . I stop installation . Delete everything , look for any
trace in Spotlight , Library . Nothing could be find .
Now , every time I open Safari , Firefox or Chrome , it will open in my home page , but when I start looking for something in steed of Google page , there is
''search.genieo.com'' page acting like a Google . I try again to get raid of this but I can not find solution .
With more research , again using genieo.com search eng. there is lots of articles and warnings . From that I learn do not use uninstall software , because doing this will install more things where it come from.
I do have AppleCare support but its to late to phone them , so maybe there some people with knowledge , how to get this of my computer
Any help is welcome , English is my learned language , you may notice this , so I'm not that quick with the respondGenieo definitely doesn't help with your router. It's just adware, and has no benefit to you at all. They scammed you so that they could display their ads on your computer.
To remove it, see:
http://www.thesafemac.com/arg-genieo/
Do not use the Genieo uninstaller! -
I ended up letting my itunes match subscription go because I was having a lot of problems with it. I was getting a lot of music where it would play the censored version instead of explicit like I have. After attempting numerous times to fix I gave up and let match expire. I had updated my library by downloading a number of AAC versions from itunes and then manually deleted all of them and added the proper files back by re-ripping my CD's again. I also added a bunch of new music and because I use a rating system, re organized all my music and rated some stuff with new ratings and higher star ratings.
About 3 months passed and I decided to give match another try. After getting it, I found it odd that my database was put there in virtually no time. Not only that, a significant amount of music I deleted (but was in the old match subscription) showed up. I knew it was broken at that point, but today, I was listening to music and items which I know have been updated and changed, have also reverted back to old settings. Is there a way to fix this?
Also, I'm REALLY annoyed with match again. After all my work, I STILL have censored music as my match music. It is really annoying to have different music on my computer than what is in the cloud (not to mention the music which will not upload to the cloud and just constantly says "waiting"!!)Yeah, and it didn't work.
I had problems when I updated to iOS 5 (lost all my apps - a few of my friends had the same problem) and when there was an update to iOS 4 (camera wouldn't work). The iOS 5 issue was sorted by backup (but I lost the app data) but for the iOS 4 issue I had to return my iPod to get a new one. -
Lots of problems with newer MacBook Pro
I bought my first Mac about a year and a half ago. Unfortunately I've had lots of problems with it. I need to get it repaired, but I'm not sure what's wrong. I live in Thailand so I want to have some idea of what's going on before taking it to a shop (so they don't try to price gouge me).
The first problem happened about 9 months after i bought it. The computer would become incredibly slow. Sometimes it would take 15 minutes to boot up and sometimes it wouldn't boot up at all. But sometimes it was fine. If it did boot up, sometimes when I'd go into a folder in Finder, nothing would show up. The spinning loader graphic would just spin at the bottom of the Finder window. I ran a disk check and it said it found multiple errors that could not be fixed. I erased the hard drive and reinstalled Lion and everything seemed fine. Since I live in Thailand and I need my computer for work, I didn't want to ship it off to Apple to be fixed. It seemed fine after formatting the hard drive, so I figured it was fixed.
About 3 months later the problem came back, but much worse. I couldn't boot up or anything. I took it to a small Mac repair shop because at this point the 1 year warranty had expired. Of course inside the shop it booted up fine and I had to explain to the guy that for 5 days I haven't even been able to turn it on. Finally after restarting 4 times it began slowing down and he could see what I was experiencing. He said he could try replacing the hard drive, but couldn't guarantee it would fix it. I needed my computer badly at this point so I said let's try. I came back a couple days later and he had transferred everything to the new hard drive and installed it. Everything seemed to be working fine.
That worked, although sometimes (rarely) something weird would happen, like the computer would just shut down for no reason. But, the DVD drive stopped working. It loads a disc OK, but it can't read it and won't burn a DVD. One time it wouldn't eject my DVD for about 30 minutes. I was trying everything I could find on Google. Finally it spit it out.
Now, about 6 months later, I was watching a movie and about 10 small colored boxes popped up on the screen. They went away after a few seconds, so I closed my movie and went to shut down my computer. The entire screen then filled with horizontal rainbow colored static. It stayed for about 30 seconds, then the screen turned grey. I could hear and feel the fans blowing at full speed.
And then for about a full day it went away, until earlier today. As I was backing up all my files I played a quick part of a movie. The same squares popped up on the screen so I immediately closed the movie and they went away.
I finished backing up and then erased the hard disk. I started installing Mountain Lion, and it stopped at about 75%. I canceled the installer and restarted. After a few seconds the screen turned solid blue with white staticky lines. And now that happens every time I turn on the computer after about 30 seconds. There's no operating system because before I can even get to the installer before the screen goes.
Sorry for the huge amount of info. I just don't have enough experience with Macs to know what's going on. My current issue resembles a video card problem, the issues before resemble a hard drive and DVD drive issue. Replacing the hard drive fixed it temporarily. Could a problem with the logic board cause all of these issues?
Thanks for any help with this.A few things to note...
If you had contacted Apple about each of the issues that you reported here, they would have kept a log of the problems that would help them determine whether to continue support after the warranty expires.
You might consider asking about "Flat Rate Repair Pricing." See the discussion thread here and note that some users report that the flat rate repair pricing is only available in the U.S. and Japan.
gavin310 wrote:
(typically they just ship your computer to Singapore instead of working on it "in-house" from what I read).
Actually, I had great experiences with two different macs sent to the repair depot. One computer had narcolepsy on day one. Apple sent me a box, I packed up the PB and dropped it off at UPS. Apple fixed and returned to my house two days later. The second MBP had a known video card problem. I took it to an Apple Store Genius who ran a specifc test and deduct that it was the known defective video card. The store was out of parts and ordering would take a week. Knowing my past experience with the Repair Depot, I ask for that option. The genius took my MBP and shipped it to the depot that night. Three days later, I received the fixed MBP and on the work order, their tests showed failed fans that they also replaced. Three or four weeks later, the Apple Store called to tell me they got the video card in stock.
Gather up your grit, perseverance, and persistence before contacting Apple. Try bypassing phone support by contacting them via their online support system with the link I provided in the previous post. (I remember using the online support system and was able to choose to have them call me. At the time, I had AppleCare so i'm not certain with out-of-warranty.) Another option is to seek an authorized Apple service provider.
Good Luck! -
Users of imovie experience a lot of problems and crying for help and no one at Apple did not respond
I do not understand how a company like Apple puts experts to help users
Please note that anonymous experts in Internet offer their help for moneyUsers of imovie experience a lot of problems and crying for help and no one at Apple did not respond
I do not understand how a company like Apple puts experts to help users
Please note that anonymous experts in Internet offer their help for money -
I have been having lots of problems with my iPad 2 freezing since I downloaded the IOS7. It freezes for several minutes each time this happens. Is there something you can suggest that I do to eliminate this problem in the future?
First thing to try is a reset: Hold down the home button along with the sleep/wake button until you see the apple, then let go.
-
Guys,
I really am having a lot of problems with a program. I got the program to compile but it looks absolutely nothing like it is supposed to look. I have a deadline for tomorrow and sent my teacher an email but the chances of him getting back to me by tomorrow night for a weekend is pretty much slim to none. Anyways I am sending my output and if anyone could give me advice or feedback on why it does not look right if it is something small and if its alot of things go ahead and call me dumb.
here is my code:
import javax.swing.JOptionPane;
import java.awt.*;
import java.awt.event.*;
public class Checkerboard extends Frame implements ActionListener
private Panel topPanel;
private TextArea topDisplay[];
private Panel bottomPanel;
private TextField startField = new TextField(10);
private TextField stopField = new TextField(10);
private TextField stepField = new TextField(10);
private Label startLabel = new Label ("Start");
private Label stopLabel = new Label ("Stop");
private Label stepLabel = new Label ("Step");
private Button goButton;
private Button clearButton;
private boolean clearText;
private boolean first;
private int start;
private int stop;
private int step;
//constructor methods
public Checkerboard()
//construct components and initialize beginning values
topPanel = new Panel();
topDisplay = new TextArea[16];
goButton = new Button("Go");
clearButton = new Button("Clear");
first = true;
bottomPanel = new Panel();
int start = 0;
int stop = 0;
int step = 0;
bottomPanel.add(startField);
bottomPanel.add(stopField);
bottomPanel.add(stepField);
bottomPanel.add(startLabel);
bottomPanel.add(stopLabel);
bottomPanel.add(stepLabel);
bottomPanel.add(goButton);
goButton.addActionListener(this);
bottomPanel.add(clearButton);
clearButton.addActionListener(this);
clearText = true;
//set layouts for the Frame and Panels
setLayout(new BorderLayout());
topPanel.setLayout(new GridLayout(4, 4, 10, 10));
bottomPanel.setLayout(new GridLayout(3, 3, 5, 5));
//construct the Display
for(int i = 1; i <= 15; i++)
topDisplay[i] = new TextArea(null, 3, 5, 3);
//set color to the panel
//row 1
for(int x = 1; x <= 4; x++)
//set color for
setBackground(Color.white);
//row 2
for(int x = 5; x <= 8; x++)
//set color for
setBackground(Color.white);
//row 3
for(int x = 9; x <= 12; x++)
//set color for
setBackground(Color.white);
//row 4
for(int x = 13; x <= 16; x++)
//set color for
setBackground(Color.white);
//add components to frame
add(topPanel, BorderLayout.NORTH);
add(bottomPanel, BorderLayout.CENTER);
//allow the x to close the application
addWindowListener(new WindowAdapter()
public void windowclosing(WindowEvent e)
System.exit(0);
} //end window adapter
public static void main(String args[])
Checkerboard f = new Checkerboard();
f.setTitle("Checkerboard Array");
f.setBounds(50, 100, 300, 400);
f.setLocationRelativeTo(null);
f.setVisible(true);
} //end main
public void actionPerformed(ActionEvent e)
//convert data in TextField to int
int start = Integer.parseInt(startField.getText());
int stop = Integer.parseInt(stopField.getText());
int step = Integer.parseInt(stepField.getText());
for(int i = 1; i <=16; i++)
setBackground(Color.blue);
for(int i = start; i <= stop; i++)
setBackground(Color.yellow);
//test clear
String arg = e.getActionCommand();
//clear button was clicked
if(arg.equals("Clear"))
clearText = true;
start = 0;
stop = 0;
step = 0;
first = true;
setBackground(Color.white);
startField.requestFocus();
} //end the if clear
}//end action listener
}//end classThis will incorporate arrays, for loops, and Frames all in one.
Create a panel containing an array of 16 TextArea components that change color to correspond with the start, stop, and step values entered by the user. Perform the following tasks to create the Checkerboard Array application shown below. When the user enters the start, stop, and step fields and then clicks the Go button, the results are also shown below.
1. Call your application Checkerboard.java
2. You will need the following variables� declare them as private:
a. 16 component TextArea array
b. a Panel to hold the array
c. 3 TextField components with length of 10
d. 3 int variables to receive the start, stop, and step values
e. 3 Labels to display the words Start, Stop, and Step
f. a Go button
g. a Clear button
h. a Panel to hold the 3 TextFields, 3 Labels, and the 2 Buttons
3. Create a constructor method to:
a. construct each of the components declared above and initializes the start, stop, and step variables to zero (when constructing the TextArea components, use the following parameters: null, 3, 5, 3)
b. set the Frame layout to BorderLayout
c. write a for loop to loop the array and set each of the 16 TextArea components in that array so they cannot be edited. In the same loop, set each of the TextArea components text to be 1 more than the index number. Also in this same loop, set the background of each of the TextArea components to white.
d. set the Panel for the TextArea components to GridLayout with 4 rows, 4 columns, and both gaps set to 10
e. set the Panel for the TextFields, Labels, and button to GridLayout with 3 rows, 3 columns, and both gaps set to 5
f. add the components to their respective Panels
g. make the buttons clickable
h. place the Panels in the Frame� put one in the NORTH and one in the CENTER
i. Enter the addWindowListener() method described in the chapter� this is the method that overrides the click of the X so it terminates the application
4. In your actionPerformed() method:
a. convert the data in your TextFields to int and store them in the variables declared above
b. write a loop that goes through the array setting every background color to blue
c. write another loop that�s based on the user inputs. Each time the loop is executed, change the background color to yellow (so� start your loop at the user�s specified starting condition. You�ll stop at the user�s specified stopping value. You�ll change the fields to yellow every time you increment your loop based on the step value. REMEMBER: Your displayed values are 1 off from your index numbers!!)
5. Write a main() method that creates an instance of the Checkerboard Frame.
a. set the bounds for the frame to 50, 100, 300, 400
b. set the title bar caption to Checkerboard Array
c. use the setVisible() method to display the application Frame during execution
6. After you get all of this complete, include error handling to make sure:
a. the values entered in the TextFields are valid integers
b. the start value is greater than or equal to 1 and less than or equal to 16
c. the stop value is greater than or equal to 1 and less than or equal to 16
d. the step value is greater than or equal to 1 and less than or equal to 16
e. the start condition is less than the stop condition
f. when an error occurs, give an error message in a dialog box that is specific to their error, remove the text from the invalid field, and put the cursor in that field so the user has a chance to re-enter� this can be accomplished by using multiple try/catch statements
g. only change the colors if the numbers are valid
7. Create a clear button as seen in the example below. This button should:
a. clear out all 3 TextFields
b. change the background color of all TextArea array elements to white
c. put the cursor in the start field
8. Document!!
I know you guys are probably busy with your own stuff but any help and I would certainly appreciate itgot the yellow boxes to come up but just one box.....so is there something wrong with my yellow set background because I am not seeing any more errors
//packages to import
import javax.swing.JOptionPane;
import java.awt.*;
import java.awt.event.*;
public class Checkerboard extends Frame implements ActionListener
private Panel topPanel;
private TextArea topDisplay[];
private Panel bottomPanel;
private TextField startField = new TextField(10);
private TextField stopField = new TextField(10);
private TextField stepField = new TextField(10);
private Label startLabel = new Label ("Start");
private Label stopLabel = new Label ("Stop");
private Label stepLabel = new Label ("Step");
private Button goButton;
private Button clearButton;
private boolean clearText;
private boolean first;
private int start;
private int stop;
private int step;
//constructor methods
public Checkerboard()
//construct components and initialize beginning values
topPanel = new Panel();
topDisplay = new TextArea[16];
goButton = new Button("Go");
clearButton = new Button("Clear");
first = true;
bottomPanel = new Panel();
int start = 0;
int stop = 0;
int step = 0;
bottomPanel.add(startField);
bottomPanel.add(stopField);
bottomPanel.add(stepField);
bottomPanel.add(startLabel);
bottomPanel.add(stopLabel);
bottomPanel.add(stepLabel);
bottomPanel.add(goButton);
goButton.addActionListener(this);
bottomPanel.add(clearButton);
clearButton.addActionListener(this);
clearText = true;
//set layouts for the Frame and Panels
setLayout(new BorderLayout());
topPanel.setLayout(new GridLayout(4, 4, 10, 10));
bottomPanel.setLayout(new GridLayout(3, 3, 5, 5));
//construct the Display
for(int i = 0; i <= 15; i++)
topDisplay[i] = new TextArea(null, 3, 5, 3);
topDisplay.setText(String.valueOf(i+1));
topDisplay[i].setEditable(false);
topPanel.add(topDisplay[i]);
//add components to frame
add(topPanel, BorderLayout.NORTH);
add(bottomPanel, BorderLayout.CENTER);
//allow the x to close the application
addWindowListener(new WindowAdapter()
public void windowClosing(WindowEvent e)
System.exit(0);
} //end window adapter
public static void main(String args[])
Checkerboard f = new Checkerboard();
f.setTitle("Checkerboard Array");
f.setBounds(50, 100, 300, 400);
f.setLocationRelativeTo(null);
f.setVisible(true);
} //end main
public void actionPerformed(ActionEvent e)
boolean done = false;
//test go
String arg = e.getActionCommand();
//go button was clicked
if(arg.equals("Go"))
//convert data in TextField to int
int start = Integer.parseInt(startField.getText());
int stop = Integer.parseInt(stopField.getText());
int step = Integer.parseInt(stepField.getText());
while(!done)
try
if((start <= 1) && (start > 16)) throw new NumberFormatException();
else done = true;
} //end try
catch (NumberFormatException f)
JOptionPane.showMessageDialog(null, "You must enter start between 1 and 16", "Error", JOptionPane.ERROR_MESSAGE);
startField.setText(" ");
startField.requestFocus();
} //end catch
try
if ((stop < 1) && (stop > 16)) throw new NumberFormatException();
else done = true;
} //end try
catch (NumberFormatException f)
JOptionPane.showMessageDialog(null, "You must enter stop between 1 and 16", "Error", JOptionPane.ERROR_MESSAGE);
stopField.setText(" ");
stopField.requestFocus();
} //end catch
try
if ((step < 1) && (step > 16)) throw new NumberFormatException();
else done = true;
} //end try
catch (NumberFormatException f)
JOptionPane.showMessageDialog(null, "You must enter step between 1 and 16", "Error", JOptionPane.ERROR_MESSAGE);
stepField.setText(" ");
stepField.requestFocus();
} //end catch
try
if (start > stop) throw new NumberFormatException();
else done = true;
} //end try
catch (NumberFormatException f)
JOptionPane.showMessageDialog(null, "Stop cannot be larger than start", "Error", JOptionPane.ERROR_MESSAGE);
startField.setText(" ");
stopField.setText(" ");
stepField.setText(" ");
startField.requestFocus();
} //end catch
} //end while
for(int i = 0; i <=15; i++)
topDisplay[i].setBackground(Color.blue);
for(int i = start; i <= stop; step++)
topDisplay[i].setBackground(Color.yellow);
} //end the if go
//clear button was clicked
if(arg.equals("Clear"))
clearText = true;
startField.setText("");
stopField.setText("");
stepField.setText("");
first = true;
setBackground(Color.white);
startField.requestFocus();
} //end the if clear
}//end action listener
}//end class -
I'm having a lot of problems with the hotmail account, regularly is indicating an error in the server, that I have to introduce the password again that late that this is wrong. I have changed the password making this shorter but it does not work.
bump? Is bumping allowed? Lol.
I just really need some help here. -
A lot of problems with Oracle BI SEE 11g
I have a lot of problems with Oracle BI SEE 11g
1. I upgraded my BI SEE 10 repository and can it openning in offline mode.
2. I can't deploy my upgraded repository in EM MW Control 11g - when i try to open Farm_bifoundation_domain->Business Intelligence->coreapplication, i get error "Stream closed
For more information, please see the server's error log for an entry beggining with: Server Exception during PPR, #41".
Opening Logs by EM control doesn't work too.
in file middleware\user_projects\domains\bifoundation_domain\servers\AdminServer\logs\AdminServer.log i see this event:
<Error> <HTTP> <oratest.itera.ru> <AdminServer> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <b639ac3e56e9a463:bd6fa7f:12ac7271e09:-8000-00000000000009e8> <1283408423378> <BEA-101019> <[ServletContext@329875093[app:em module:/em path:/em spec-version:2.5]] Servlet failed with IOException
java.io.IOException: Stream closed
Have you any ideas?
3. Ok, i taking sample repository and adding a new datasource in it:
Database: Oracle 8i
Connection pool:
Call interface OCI 8i/9i
Data source name:
(DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP) (Host = oraapp) (Port = 1521) ) ) (CONNECT_DATA = (SID = MYSID) ) )
This settings are working fine in BI 10.
In BI 11g i get this funny error: "The connection has failed". I lost my time in attempts to connect to Oracle DB 8, but have not results. After that i hacked button "Query DBMS" at "Features" tab, pressed it and when get error "ORA-03134: Connections to this server version are no longer supported.".
Therefore Oracle 8 DB as datasource not supported. Am i right?
4. In sample repository i added oracle DB 10 as datasource, then added two dual tables and their connection to all layers.
Now i open BI Answers, and trying to create report with one dummy column, Now i have this error:
Error
View Display Error
Odbc driver returned an error (SQLExecDirectW).
Error Details
Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 42016] Check database specific features table. Must be able to push at least a single table reference to a remote database (HY000)
SQL Issued: SELECT s_0, s_1 FROM ( SELECT 0 s_0, "ORA10G"."dual"."dummy" s_1 FROM "ORA10G" ) djm
Database features are defaults.
Does anyone solve this problem?Turribeach, Thanks for you time.
1. It was not a question
3. Yes, i have read platforms, but not supported datasources. Now i see, that BI 11g support as datasource Oracle DB 9.2.0.7 or higher. I am sorry.
4. I'm using OCI connection type
Now i recreate Database in Physical schema and answers is showing report data for me! But only from one table, when i use columns from to tables from one datasource, i geting error:
Error View Display Error Odbc driver returned an error (SQLExecDirectW). Error Details Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 46008] Internal error: File server/Utility/Server/DataType/SUKeyCompare.cpp, line 875. (HY000) SQL Issued: SELECT s_0, s_1, s_2 FROM ( SELECT 0 s_0, "Ora10g"."hierarchy_obj_cust_v"."sort_order" s_1, "Ora10g"."NSI_SCHEMA"."SCHEMA_NAME" s_2 FROM "Ora10g" ) djm
Edited by: serzzzh on 03.09.2010 3:44 -
FACING A LOT OF PROBLEM WHEN USING CONNECTOR
dear all, i am using the 9.0.4.2 Outlook Connector and i am facing a lot of problems can u plz help me
1-when forward a message with an attachmant it dosent forward that attachmant,
i have to create a new message and attache the file on it.
2-if i recived an email how was sent by a user to a DList and when reply to this email it dosent reply to the emai sender but rather to the list.
3-change password work on 2000 but in xp and 2003 it shows invisabel (grayed)
4-syncronizing global address list can be done form 2000 but form xp and 2003 there is no sync. option. how can i donwload the address book.
ihave OCS R2 on RHAS 3.0forwardin emails attachements might be part of the new functions in outlook2003 which very unhelpfully simply removes some types of attachments. seach for
the following reg hack will allow attachements cmd,exe and vbs for example. Search for parts of that string in google for more details if that is your problem.
[HKEY_CURRENT_USER\Software\Microsoft\Office\11.0\Outlook\Security]
"Level1Remove"="cmd;exe;vbs" -
A lot of problems with Lion Server in Mac Mini Server
I have a new Mac Mini Server and I have a lot of problems.
The server application works well for a day, then start to have problem, for example: I can not change the configuration of the share folder, I add a new user but he can not see some folders.
Then if I login the Mac Mini with another user, he can not see the starting folder and if you open a new folder you see a lot of strange documents.
Later, with administrator user, I can not login the server application, I put the user name and password but it refuses it (user name and passowrd are correct)
In the end I also can not login the computer.
I reinstalled the Lion Server 2 times but nothing change, after 2 days it doesn't work like before.
I'm very upset, this is the first time in more then 20 year I have a problem with an Apple computer.
What can I do?
Please help me
ThanksTurribeach, Thanks for you time.
1. It was not a question
3. Yes, i have read platforms, but not supported datasources. Now i see, that BI 11g support as datasource Oracle DB 9.2.0.7 or higher. I am sorry.
4. I'm using OCI connection type
Now i recreate Database in Physical schema and answers is showing report data for me! But only from one table, when i use columns from to tables from one datasource, i geting error:
Error View Display Error Odbc driver returned an error (SQLExecDirectW). Error Details Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 46008] Internal error: File server/Utility/Server/DataType/SUKeyCompare.cpp, line 875. (HY000) SQL Issued: SELECT s_0, s_1, s_2 FROM ( SELECT 0 s_0, "Ora10g"."hierarchy_obj_cust_v"."sort_order" s_1, "Ora10g"."NSI_SCHEMA"."SCHEMA_NAME" s_2 FROM "Ora10g" ) djm
Edited by: serzzzh on 03.09.2010 3:44 -
Facing a lot of problem in connecting to 3G speed on my iphone4 . Done with all the checks as network reset and also done with clearing cache n cookies still the problem is same . I hardly get 2g speed even . Thus I request to help to fix this problem.
Your code is absolutely unreadable - even if someone was willing to
help, it's simply impossible. I do give you a few tips, though: If you
understand your code (i.e. if it really is YOUR code), you should be
able to realize that your minimum and maximum never get set (thus they
are both 0) and your exam 3 is set with the wrong value. SEE where
those should get set and figure out why they're not. Chances are you
are doing something to them that makes one 'if' fail or you just
erroneously assign a wrong variable! -
Custom Tags starting with $: lots of problems
I'm building an extension for MovableType template tags.
Those tags can be delimited in several ways: <MTNameOfTheTag>
or <$MTNameOfTheTag> or even <$MTNameOfTheTag$>. Since
the dollar sign is not allowed as tag name, i put a
prefix="<$" in tag definition, but now i have some problems:
1. even if in tag chooser i can see the dollar-prefixed tags,
i cannot see them in code hints (I mean "automatic" code hints,
those floating menus automatically made for every tag/every
attribute/every enumerated attriboption in library).
2. I tried to manually code tags in codehints.xml file with
the "<$ pattern (so i can change the icon associated to my
custom tags, too. That's will be very elegant) but I loose "child"
codehints menus: the first codehints menu (the one i manually made)
comes up, but those for attributes and attributes values don't.
3. With the solution in point 2 not only i loose "automatic"
codehints, but i have to write THREE files for every tag
(taglibrary, codehins, third party tags file). Lot of time :/
4. Dollar signs, in both start and end, are NOT part of the
name, but part of the tag, like a prefix or a suffix. With an
attribute i should have:
<$MTBlogName donald="goofie"$>
and not:
<$NTBlogName$ donald="goofie">
as actually i have
so, as i said...a lot of problems! i hope someone can help
me...its really an hard sunday, today! :/
tnx in advanceI think you might be moving into creating your own server
model.
Just a thought. -
my iphone3 its ben havin g a lot of problems it will not lock i open a game and
it will go to ipod im going to get a new one but i would like to know what is rong with itYeah, and it didn't work.
I had problems when I updated to iOS 5 (lost all my apps - a few of my friends had the same problem) and when there was an update to iOS 4 (camera wouldn't work). The iOS 5 issue was sorted by backup (but I lost the app data) but for the iOS 4 issue I had to return my iPod to get a new one.
Maybe you are looking for
-
Display shortcuts stop working
Display shortcuts stop working. Reboot starts everything up again.
-
Hi Friends, I am working as a xi consultant, I have no idea about cost centre,profit centre and orgarnizational structure. Please expain me with real life example in an organization. Thanks, Suresh.
-
CAF case insensitve search using QueryFilter
Is it possible to do case insensitive search in CAF using QueryFilter? By default it does case sensitive searches in data elements of Entity Services. I am using 7.0. Also according to http://help.sap.com/saphelp_nw70/helpdata/en/44/6359a603b13674e10
-
Not able to open the existing PDF files from Content Server in VL02N
Hi All, In Delivery transaction VL02N, we are not able to open the PDF file attachments which were created in the Past (Ex. 01/01/2014) from the Content Server. Recently upgraded to Enhancement Pack 7 and not sure whether the issue is due to this upg
-
I am trying to have a card printed and the printer is asking that I make the image in "spot color". I have no idea how to go about doing this. I created the image in Illustrator and formated it in InDesign. Can anyone help me out?? I am posting links