Low latency mode doesn t work?

If I enable "Low latency Mode" nothing happens, Ioaded tons of Plugins and set the limit to 1 ms....Shouldnt it bypass some plugins? Someone who knows the problem

does it work for you?

Similar Messages

  • Can't send to bus when in low latency mode?

    My colleague and I have almost the same setup, except he is running OS X 10.8.5, and I'm running OS X 10.9.4, Both are running Logic X 10.0.7. He has Apogee hardware (Symphony 64 card to DA16X/AD16X), and I have a UA Apollo.
    For some reason, this works on my setup, but not on his:
    Set up a bus send on any audio or VI channel, and assign the output of that channel to outputs 3-4 (outputs 1-2 are both of our main outs). The purpose of this is to send to a cue/headphone box.
    Set latency compensation to Instruments and Tracks (not ALL, setting it to ALL defeats this)
    Turn on low-latency mode.
    Turn on Software Monitoring (buffer is set to 64)
    Record enable that track.
    On my setup, I get signal on channels 3-4, on his, no signal as soon as record is enabled
    Auto-input monitoring is off in both cases.
    On my setup, the bus popup turns orange, but I still hear the signal, on his, it turns orange, but no signal.
    All plugins removed on the track and the bus.
    Weird.

    Bus Send is set the same on both systems, Post Pan,  Post Fader,   Pre Fader ?
    Good point, I'll check that
    Bus is set to output on 3-4 ?
    Yes, on both systems
    Bus level is the same ?
    Yes, similar anyway
    Sure you friend doesn't have any plugins on the master output bus  ?
    I didn't consider that - somehow didn't think that plugins on the master bus (which is outputting on 1-2) could effect a different bus. Will check that tomorrow.
    Do you by any chance have direct monitoring enabled on the Apollo, any input signal will be heard.
    I do use direct monitoring on the Apollo, but that is not a factor - it's prerecorded material we are trying to monitor, not input signal.
    Curious as to why are you running in Low Latency mode, it is for a specific purpose not something to be used in general recording/work.
    He is running on an older Mac tower and uses a lot of plugins and prefers software monitoring, and finds that he has problems unless he enables low latency mode. I usually leave it off, I just wanted to see if the issue was present on my system as well, and it's not.
    Thanks, will report back.

  • Low latency mode

    Hi,
    I'm doing vocal recording now,facing latency problem.Finally i'm trying to apply the LOW LATENCY MODE ,it really solve the latency when press the Rec Enable button...but howevery i try to route with Aux or Bus(Vocalist required some reverbs while singing)...it doesn't work..and level meter didn't show any input signal on the Aux or Bus!!!
    and when i apply the Low Latency from the Vocal track Send button...level meter become active on Aux or Bus but the LATENCY appear again even the Low Latency Mode i still ON it.
    What's my problem here...
    Urgent!!!!Thanks for helps...

    the better setting in recording (with Motu device) is:
    Don't use "low latency mode" (it is a logic 8 feuatures but it is not so useful)
    Sample buffer set to 256k
    PDC set to Software and Instruments (avoid to use Aux or Multi instruments mode)
    Reverbs and delay can be used on the Buss because latency on reverbs gives you a good predelay effect... (when PDC is set to All, usually, I use sample delay in reverber Buss in order to be able to have the same great reverbs sonds )
    ... PDC set to ALL gives you a lot of latency...
    if you use Multi Instruments.. the better way is: (I never use Multi out instrument... i prefer to export as audio the parts!
    Bounce the instrumental parts...
    open a new project, import the instrumental parts... set PCD to "Track and Instrument)
    When Mixing .. mastering PDC must be set to ALL...
    in every other situation (expecially in recording phase) "track and instruments" PDC setting is the better choice!
    G

  • Xperia Z2: Stamina mode doesn't work aparently

    Hi,
    Stamina mode doesn't work aparently on my phone. I try all the configurations but the sotware doesn't turn off the wifi and neither the mobile data coming from the operator when i block and turn off the screen of the device. I continue receiving information from all the apps and i haven't done any exception on the stamina configuration. Any idea to solve this?
    Solved!
    Go to Solution.

    Looks like you are talking about Low-Battery mode...
    First make sure that you have turned it ON. After that just see "Activation" section under Low Battery mode to find at what level it has been set to activate.. By default, Low battery mode gets activated at 20% battery level.

  • Low latency mode: what's the sense?

    I've read it bypasses plug ins which causes latency. But if it is so what'is the sense of this function? If I understand well in this mode I don't know exactly which plug in will work and which no....
    I cannot accept a situation like this.
    Apart from anything else I did use low latency mode (because I listened some latency after having inserted a plug) and I checked all the plugs during playback and they all seem to work. So?
    I don't understand...

    Usually I use Low Latency mode in when mixing-mastering.
    I use UAD DSP plugins on the master... this is cause of many issue... the MAIN problem is that Logic is able to compensate Plugin Audio Latency (PDC)... but not Graphics .. (GPDC is not available... instead Logic 7... Logic 7 have GPDC!!! ... in Logic 8 graphical plugin delay compensation is a missing features)
    the resulting behavior is that All meters show anticipate by the sound...
    but this is not fixable.. or better.. Apple developers must included the Graphic delay compensation in order to get metering in sync with Audio... (I hope in the 8.1 version)
    Anyway.. i love UAD sound and I use them in any case..
    return back to your question, I use Low Latency mode when i need to record some missing details .. without get DSP latency!
    It is a helpful features (not so basical but helpfull).
    Logic Pro 7 is also a great DAW!
    G

  • Low latency mode didn't bypass latent plugins, or turn them orange

    in our case it was waves' bass rider plugin.  we had low latency mode enabled, the plugin was bypassed even, and still it caused the entire output to be latent.
    i was under the impression that low latency mode was supposed to bypass these things and turn them orange right?
    our latency limit was set to zero as well.
    ideas?

    There are so many factors that affect latencey and if you're making your living or it''s really important, I'd roll up my sleeves and tackle this puppy head on.  Do you have a really high track count?  Are you running a lot of plug ins?  What is the disk buffer size set to? What do you have the processing threads set to?  How much RAM do you have? Are you using an external drive that's fighting to keep up? What sample rate are you running at........
    I think you see where I'm going with this!  It's a slippery slope my friend but nothing you can't figure out.  It really all depends on understanding what you have and how best to optimize it for what you want to do.  That's why a lot of the help forums can be so confusing because there isn't a simple answer that works for everyone.
    In the meantime, if you really wanna just get to the business of making music try monitoring through your desk when you're tracking and only use the plugins for playback (disable software monitoring, but only if you have the hardware that will enable you to do so).
    Good luck!

  • IOS 5 Safari Reader mode doesn't work on an iPad 1º generation

    iOS 5 Safari Reader mode doesn't work on an iPad 1º generation. How can I fix that?

    Hi.  I am having the same problem on an original iPad. The tabbed browsing works fine, but no "reader" button is showing up in the URL window at the top...
    Anyone else seeing this and is a reinstall of ios5 really needed?
    Thanks

  • Boot up from target disk mode doesn't work. (Why?)

    I have a 2010 Macbook Pro, and a 2013 iMac. I connected the Macbook pro with the firewire cable to the iMac, and enabled target disk mode on the laptop. (It is successful because I see the hard drive appear on the iMac desktop.
    I restart the iMac and hold 'option' to show the hard drive list, and sure enough the Mac Book Pro hard drive appears. I select it, and this lovely icon greets me.
    From this point, I have no idea what to do.
    Would you happen to know why it doesn't work and/or how to fix it?

    I am able to do that... this is not the problem.
    I have seen people boot up from the hard drive using target disk mode. When I try to do it, it doesn't work. Does this feature still exist?

  • Flashing in Windows Modes doesn't work

    I'm running Windows Vista Business, and when I try to update my BIOS in windows mode, it fails.
    I'm using MSI Live Monitor 3. After finding the bios (1.5), I use "windows mode" to flash.
    A command-line window comes up, and I can see everything getting flashed. However, after it's done it reboots automatically. After both the initial splash-scrren and the SATA-screen showing my drives, I get an CMOS checksum failed error, and I can either start fiddleing with the setting themselves, or just use defaults.
    I've tried both.
    And after both times, after I get back to windows again, Live Monitor 3 says it has an update for me - bios 1.5. So I can only conclude it wasn't installed, somehow.
    Before doing the install, I closed ALL programs, except windows itself. (I'm saying this, because Live Monitor 3 wishes me to close it..........)
    I cannot flash via a floppy-drive because I don't have one.
    Another problem is that DigiCell keeps telling med: "Failed to load driver". I have no idea what it even IS, but I'd just like to see what free software I get. :P
    Thirdly, has anyone heard of problems with external USB drives and MSI mobo's? I have a 500gb My Book drive that throws I/O errors in Vista, but not in XP on another PC...
    My PC is:
    MSI P965 Platinum,
    2.13ghz Core 2 Duo,
    2048mb DDR2 RAM, 533 Mhz
    Regards,
    Søren Andersen

    Thank you Jack!
    It is indeed updated to 1.5 - I just didn't notice, since I had the full-logo thing on.
    I also updated the drivers, but unfortunately that didn't help. :-(
    I've been trying since friday to fix this both on the WD forum (http://websupport.wdc.com/forum/topic.asp?TOPIC_ID=5948) and on Microsoft's tech forum (http://www.microsoft.com/communities/newsgroups/en-us/default.aspx?dg=microsoft.public.windows.vista.hardware_devices&tid=dc8d09ab-0d98-452c-b2d3-a0948f756dda&cat=en_us_9F280F8D-E6BF-F78C-234A-416CF09D5DC5&lang=en&cr=US&sloc=en-us&m=1&p=1)
    but we've still been unable to fix it...
    To be honest, I don't think it has anything to do with hardware. The drive doesn't work properly on this PC (MSI / Vista) but does on my laptop (Dell / XP), but it has to be checked...
    Basically, it keeps throwing 0x8007045D I/O errors, but I can see noone in here has had similar problems.
    So, thank you for your extremely swift replies and very great help!
    Regards,
    Søren

  • When Searching for attachments to mail, preview mode doesn't work

    When I am in mail and am composing a new email and I click "Attach" to attach a file, the current folder comes up and shows the preview mode of every file type (i.e. pictures and pdf previews). No problems. However, if I then do a search for something (my name for example) to narrow down my choices of files or images to select, the next search level does not show a preview of the files or images, just a .pdf icon or the .jpeg icon - NO PREVIEW. This is extremely frustrating! I tried on different folders and the same results occurred. Any ideas or is this a bug?

    Hi Pranava,
    I couldn't reproduce this issue, when I create root folder FS0 in "Shared Documents" and start a full crawl, I click the FS0 link from search results page, it will open the FS0 folder as well as folder under FS0.
    Please right-click the FS0 name hyperlink (e.g. mine is http://sp/Shared%20Documents/FS0) and paste in IE browser see if it could be accessed successfully.
    Also test if other Shared Documents have this issue in other site collection or web applications, if not, run a full crawl may do a trick (please reset search index if only full crawl still doesn't work).
    Thanks
    Daniel Yang
    TechNet Community Support

  • The lower case P doesn't work on any of my keyboards.

    Tried other keyboards and it doesn't work on any of them, so it must be a software Problem. Any ideas how to fix?
    I have a iMac  Running OS X Yosemite 10.10.2

    Please read this whole message before doing anything.
    This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
    Step 1
    The purpose of this step is to determine whether the problem is localized to your user account.
    Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
    While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
    Test while logged in as Guest. Same problem?
    After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
    *Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
    Step 2
    The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Please take this step regardless of the results of Step 1.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

  • OS 10.8 just installed. "Hot Corner" to put new iMac 2.7 GHz Intel Core i5  to sleep mode doesn't work. Have tried cordless and corded mouse with same result. Momentary sleep, immediate wake. Any idea how to fix?

    Set "hot corner" to put iMac to sleep.  Doesn't work.  Selecting the corner will momentarily put to sleep, but immediately rewakes.  Have tried all four corners with same result.  Have tried with wireless mouse and with corded mouse with same result.  Any ideas as to how to fix?

    You've been so great, I want to thank you for all the help over a very frustrating day.  Last evening, I redownloaded and installed the fresh copy of Mountain Lion.  The problem remained.  After installing the new OS 10.8, any clicks on a web page (Firefox browser) didn't open the page, but instead made a copy of the page on the desktop. Felt it must be hardware  degrading, so I set up a case with Apple support for today.  Early in the diagnostics, I had swapped out for a corded mouse and the problem remained.   As a last try, I changed out my wireless mouse for a different wireless mouse. That seems to have done the trick. My Logitech mouse is incompatible with OS 10.8.
    Thank you again, so much!
    .../awards rkaufmann87 500 points!

  • How do i add a bluetooth device to my mac? there is no " " button in my bluetooth preferences and turning the devices to discover mode doesn't work

    How do i add a bluetooth device to my mac?  There is no " +" button in my bluetooth preferences and turning the devices to discover mode doesn't work

    The Bluetooth setup assistant should "find" a device in range when that device is turned on. What are you trying to add?
    Wireless input devices: Bluetooth frequently asked questions ( How do I add or remove a wireless device to or from my Mac (pairing or unpairing)?)
    Barry

  • Pressing D on boot to get into Diagnostic mode doesn't work. Macbook Pro with OSX 10.6.8

    My charger has stopped working all of a sudden for my MacBook Pro. I tried my friends charger and it works. I've seen a few people mentioning that their charger started working again after running a Diagnostic test at boot up by pressing "D" after powering up the computer.
    I see this instruction all over the web, but it doesn't work for me! I have the OSX DVD in the drive. Holding down "C" while booting makes it boot on the DVD, and holding the Option key will give me a boot menu. But it just boots normally while holding down "D".
    Am I missing something?

    Press D during startup
    Start up in Apple Hardware Test (AHT).
    Apple Hardware Test is included on the DVDs that are shipped with some Macintosh computers. If the copy on your hard drive becomes unavailable, use the DVDs to run Apple Hardware Test.
    For Intel-based Apple computers that shipped with Mac OS X v10.5.4 or earlier, Apple Hardware Test is located on the Mac OS X Install Disc 1 and should be included with your computer.
    For Apple computers that shipped with Mac OS X v10.5.5 to 10.6.7, Apple Hardware Test is located on the Applications Install Disc 2 and should be included with your computer.
    For some Apple computers that shipped with OS X Lion, if Apple Hardware Test cannot be found on the hard drive, an Internet-based version starts up instead.

  • S3 mode doesn't work fine on K8N Neo-fsr since overclocking, please help!

    I have a K8N Neo-FSR (MS-7030) BIOS version 1.6 (I tried 1.4, 1.5), running AMD64 2800+ SK 754, 2x 256MB DDR400 Kingston valueram pluging in slot 1&2. It runs well except S3 mode    .
    Since I overclock HTT (everythings else have their own default values), S3 mode seems to work so crazy . After wake up from this usefull stop-grant standby mode, HTT is given back to its original speed, 200MHz, without notice (?!)  .
    You know that I don;t like this much, do you? 
    Who responsible for this function? Mainboard or CPU? If it's mainboard, which department will be sentenced, BIOS or chipsets/ICs? 
    Could anybody give me a solution to achive higher speed by overclocking without giving up using S3? 
    Thanks so much!

    It's a bad new! I had bad feeling about DFI with the same problem, S3 mode resuming bring FSB back to df and even sometimes led the system to the ruin. But upgrading bios solved this issue. My old Abit did S3 mode fine. Now I have a new MSI and once again I must use teknophyle's way or slow hibernation instead.
    On the same occasion, I wana ask about some shortcoming in 1.6 bios: power on by keyboard/mouse and power led options. I only found S3 wake up by keyboard/mouse but not keyboard/mouse power-on options! There is power led option in version 1.56 but it disapeared in 1.6. Now my mobo has no signal to differentiate between sleep and power-off. would you give back the useful power led option and add power on by combination keys in the near future bios version, syar? Look forward to hearing some good new from you :D.

Maybe you are looking for