Low Speed Internet - on iMac Only

Hi,
I have an early 2008 iMac running 10.9.5. 
Recently the WiFi on it has been running painfully slow, compared to the other devices in my home.  I thought it was due to the location in my home but it doesn't appear so as I've compared it to a Macbook.
The iMac's speed test results in download speeds between:  1.2 and 5.6 mps.
The Macbook's speed test results, when right next to the iMac:  25 mps.
Around where my airport is (downstairs), speeds on the Macbook are 50+ mps, which is what I am paying for.   (The iMac is upstairs.)
Is there a way to fix this so the iMac runs at the ~25 mps like the Macbook does?  Is this a general problem with Mavericks, which I've read from others?
One solution I tried which did not work is:  Go To> /Library/Preferences/SystemConfiguration > Delete the files, reconnect and get a fresh reconfigure.  This did not solve the problem.
Any help would be greatly appreciated!

On the iMac (machine getting the low speeds)
PHY Mode: 802.11n
Channel:   1 (2.4 ghz)
Security: WPA2 Personal
Signal/Noise or RSSI:  -81
Transmit Rate: 39
On the Macbook Pro 10.9.5 (machine getting high speeds)
PHY Mode: 802.11n
Channel:   1 (2.4 ghz)
Security: WPA2 Personal
Signal/Noise or RSSI:  -75
Transmit Rate: 156
Hmmm, so clearly the Macbook Pro has a much higher transmit rate.  Is that fixable?

Similar Messages

  • Low speed internet -- intermitte​nt problems

    Usually my internet service is fine; but, occasionally it will be very slow (essentially unusable).  The past couple days it has been VERY slow and unusable.  I have tried restarting the computer and internet/router many times to no avail.

    N_e_a_l wrote:
    Usually my internet service is fine; but, occasionally it will be very slow (essentially unusable).  The past couple days it has been VERY slow and unusable.  I have tried restarting the computer and internet/router many times to no avail.
    Hi you can follow the below steps to increase your internet speed
    1)Delete all cookies and temporary files.
    2)Use different browser. Because normally some browser enabled javascript
    and flash video ,so the webpages is loaded very slow.So you can try  it
    different browser.
    3)Virus,malwares is also another important thing it will make a slow connection.
    So use a good antivirus software to remove all virus and malwares .
    4)You can try to close unwanted applications
    Finally go to this site Scanmyspeed.com then check your internet speed it will  definitely works very fast

  • INternet speed difference between iMac and MBP

    I have an imac 27" that is barely one year old and a three year old MBP. Today, I signed up for faster Fios internet service which is supposed to be a maximum of 25 Mbs both up and down. I then checked the speed on my iMac and see I am averaging about 10 Mbs down and about 8 Mbs up. I am not that concerned that I am not getting the theoretical maximum performance. For one thing I am not hardwired to my router but am using wireless g. I also ran the Mac internet tuner that seemed to actually increase the speed somewhat.
    I then checked my MBP that is sitting right next to my iMac. I am getting around 15 Mbps down and about 17 Mbps up. I repeated this several times as I did for the iMac. I am surprised at the iMac being so much slower (about 33% slower). I can only assume the hardware in the MBP is better for wireless communication than in the iMac. Can someone explain why this is so?
    thanks,
    Shannon

    Download an app such as Speedtest to your iPad.  Test both ways and see the results for yourself.

  • Internet connecting at much lower speed lately

    I have HSI Enhanced and have had it for 10 months at this location and for a number of years at my previous location. Last October I was connecting at 3360 / 832 kbps. After some months it went down to  around 2800 / 832 kpbs. I wasn't crazy about speeds getting lower as time went on rather than the connection being improved, but it was pretty much free of disconnects and reliable so I was happy with it.
    In the past month or so I had noise on my voice line which Verizon fixed, but my connection is now 1792 / 448 Kbps all the time, that is a drop I will not accept if this is the way it is going to be from now on. Also there is a lot of losing the connection, not to the DSL, that light stays on but the internet light goes off. I went through the usual channels online chat, telephone support to wherever that goes. I'm done with all that, that's good for people with trouble using their modem, etc. or can't connect it but not what I am looking for.
    Finally they sent out a tech who was a nice enough person, what he did was call a central office and after them first claiming the lower speed was the right speed they put the connection back in the area of 3360/832. Then they said it will probably adjust itself to down around 2800 down, which it what I had before so I was OK with it. After several days with a number of disconnects (they don't last too long but very annoying) I am back to 1792 / 448.
    I am using the same modem - Actiontec GT704WGB
    I don't need a tech call here in the house again, nothing has changed in here since I moved in months ago. They can check the outside signal without me waiting around for them. They don't have to stand in here to call an office on their tablet.
    I need to hear from Verizon personnel that can tell me LOCAL information about why my connection speed has tanked and why there are dropouts now. And most importantly, why it can't be the same as it was for all those months. As I said, I was happy with that - especially when it was 3360 / 832 kbps.
    Solved!
    Go to Solution.

    When Verizon turns your speed back up, they have to disable the optimization system they use on the lines to maintain your speed, since it sounds like that is just turning your speed back down after a few days. Make them fix it back again.
    For future note, if you do have problems with your DSL and you're also having audio quality issues with your phone, call Voice Repair, and leave DSL support out of the mix. DSL support usually dials back the speed for a line issue from what I've seen as a first try basis. If you do have noise that disappears when the DSL modem is off, then that could be from other things which DSL support OR phone support will be needed for.
    Ex: Two years ago I had a problem with my Frontier DSL line having a ton of static on the line. The DSL modem was not synchronizing, however the noise stopped when I shut off the modem. It turns out, the night before lightning struck a tree outside of my home, and caused the DSL modem which was several years old to fry. The modem was still powering up, but the chip responsible for the DSL connection itself was blown. A new modem from Frontier via DSL Support fixed the DSL connection AND the static.
    Ex2: At a local business with Verizon DSL, they hear static on their line from time to time, but only while the DSL is active. The problem was not with the DSL itself or any filters, but as the static got worse it began to show up without the DSL being connected. Voice repair was dispatched instead of calling DSL Support, and resolved the problem by running new cable between the building and the Verizon copper trunk. In addition, they found and corrected some corroding splices.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

  • The speed of my iMac slow only 2 weeks old why?

    the speed of my iMac slow only 2 weeks old why?

    In addition to abrody's questions, have you downloaded non-Apple software that may be automatically loading, and perhaps not Lion-compatible? Go to System Preferences, users, and look at login items under your user ID.  This is easy to check ... do a safe boot by holding the shift key down when you boot. The boot itself may take longer than normal, but once the boot finishes, if the performance is what you'd consider normal, look to your login items. Also, while looking at System Preferences, look at any programs noted at the bottom of the window.

  • Low speed

    Have very low speed - 0.225 mbs, download. On signing up I was told I will be receiving minimum of 8mbs, average of 15mbs and a maximum of 19mbs. Besides being passed from pillar to post as no-one understands why the broadband is so low I have just been informed that the maximum I can get is now 10mbs - quite a big difference? I have also been told I will be charged to have the phone line looked at even though it was only installed by BT two months previously so I will be paying twice. Is this right? I have been lied to, called a liar, transferred to every department within BT. Each member of staff has told me they can't help that I need to be transferred to a different department so after five hours on the phone I am still at square one! This has been going on for two months. Oh I was also told I would receive compensation for not receiving a service but apparently I'm suddenly not eligible for this. I can get faster broadband (more than 10mbs) for cheaper elsewhere. BT have broken the contract by not supplying me with the service that they promised. BT staff don't seem to know much as they can't even agree on the rate of broadband I should be receiving. This is not to mention how rude they have all been towards me. I am thankful that everything is recorded as this proves that I am not at fault and there are obviously training issues that need to be addressed within all departments in the company. Has anyone else had the same experience? Can any moderators respond? 

    Hello, thanks for your response.
    I can assure you that i have tried absolutely everything including replacement router, filters etc.
    The line was only installed on the 14th April, and BT only guarantee their work for a month! I paid £130 to have a line installed...
    They have admitted there is a fault in the line, but even after 6 hours of diagnostic tests still cant find the problem. These tests werent all carried out today but over the past 2 months yet they still didn't send another engineer round to check the line had been installed correctly. I was only offered this option once the "28 day" warranty on the line had expired hence I was expected to pay for it. If this information is incorrect, i have been lied to by the Technical team at BT once again.
    The end result after approx 6 hours on the phone today was that i demanded a full refund for the past 2 months of broadband that i was paying for but not receiving, which was granted after a struggle, and a cancellation of the contract due to BT breaching the contract on at least 2 counts. The first being that i was lied to by the initial sales advisor about the speed of the internet connection i was to expect and BT could not honour this and the second due to paying for a service that i was not receiving. I still have not resolved the problem with the line itself which needs to be looked at by BT regardless of which isp i decide to go with now.
    I think BT really need to look into the staff they have on the end of the phone as they have been nothing but helpless and i can imagine that they have lost BT 1000's of customers due to their lack of knowledge or training.

  • Dear sir  Thank you very much. I am not a computer davy. still I ail try to explain. I am in Chennai India. My service provider is BSNL. I have a broadband connection wit 4 mb speed - though I get only 3 to 3.3 mb. The TC is connected to the modem *** rou

    Dear sir
    Thank you very much. I am not a computer davy. still I ail try to explain. I am in Chennai India. My service provider is BSNL. I have a broadband connection wit 4 mb speed - though I get only 3 to 3.3 mb. The TC is connected to the modem *** router through ethernet in wired LAN1 socket. My iMac is connected to the modem in LAN2 socket through either net. Though the TC is permanently connected to the modem-router, it gets connected to the internet only if it is shown in the dock. If it is exited from the doc, it loses internet connection. I tried factory reset. Still the same problem. Therefore, unless the iMac is open and the Tc is shown in the dock, TC is not connected to the internet. Therefore all the time iMac need to be open and running. I hope, eih little knowledge I have explained. Thank you
    S KANNAN
    IRS(RETD)

    The TC is perhaps in the wrong mode..
    If you have a modem router the TC should be connected by ethernet and the computer plugged into the TC not the modem.
    TC will be in bridge mode.. but it can lose connection on a daily basis.. if you have that issue downgrade the firmware as later firmware is not reliable.
    I recommend 7.6.1 but the earlier ones are better on 7.5.2 .. anything more than 18mths old should go back to 7.5 firmware.

  • Connection issues and low speeds

    Hi there,
    my family have been with BT now for about 3 or so years and the connection had been rather good until about late last year. According to my family it's everytime I come back home from uni the internet starts to play up as in:
    . Low speeds
    .Drops out and loses connection
    Believing it was somehow my laptop causing the issues I backed everything up and completly wiped it because BT support thought it may be a virus on my machine even the the checks came back with nothing. So I've wiped my laptop and restarted it like it was a brand new laptop...still we're having these issues so I refuse to believe it's my laptop causing the problems. I've changed the chanel on the hub so many times it just doesn't make a difference. Tried different DSL adapters tried different cables even a wired connection causes problems. I am begining to think it's because the router has had it but I am willing to try anything at this point before asking for a new router from BT. Even BT don't seem to know what the problem is all they do is reset the routers chanel every single time I ring them.
    So any advice or help would be greatly appreaciated
    Many Thanks
    Benjamin
    PS - sorry for any grammar/spelling mistakes , I've written this in a hurry before the internet drops out again...

    Hi Welcome to the community forums
    Here is a basic guide to getting help from the community members done by CL Keith Please read through the link posted http://forumhelp.dyndns.info/speed/first_steps.html
    once you have posted the information asked for then the community members can help you more
    Thank You
    This is a customer to customer self help forum the only BT presence here are the forum moderators
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • How can I set up a home wireless network with Comcast high speed internet?

    I just signed up for Comcast High Speed Internet. I was able to get my Power Mac onto the internet. However, I connected my Airport Extreme and am unable to get it to recognize that I have an internet connection. I want to set up a wireless network in my apartment. Comcast tech support said that I only have one IP address.
    Any suggestions as to how I can get my wireless network up and going? Thanks!

    Should I change set up so that cable goes from the cable modem directly to Airport Extreme and then use the ports on the Extreme to run Ethernet Cable to Power Mac and other devices?
    Yes
    As an aside, would this setup allow me to hook my iBook up to Airport via Ethernet cable and let it get into Internet that way?
    Yes

  • I Can't Burn a CD any more! and a lower speed does nothing - HELP!

    I have been burning CDs on this machine (imac 10.3.9) the same way for years and years. (7)
    Up till last month.
    This is what I get when I burn a playlist.
    "itunes can not burn this cd because your burn speed is too fast for you cd burner or media. Choose a lower speed in the burning pane then try burning again."
    I've tried that - even though that seems silly considering I've had no problems at my current settings until now. The lowest burn speed (1) gives me the same error.
    I'm hating life and my mac right now, something I though I'd never say.
    Anyone?

    If you don't have Nero, check out http://discussions.apple.com/message.jspa?messageID=9229334#9229334. I think some people have found a way to get just the Burn Rights program.
    If that doesn't work, some people seem to have luck with editing the registry or messing with filters or gear drivers. Check out this discussion starting with Tytus (he came up with the Nero fix) on March 22:
    http://discussions.apple.com/thread.jspa?threadID=1939904&tstart=0
    Hope this helps!

  • Does backing up my hard drive to time machine gain me more space/speed on my iMac?

    I have an iMac. here are the specs:
    Hardware Overview:
      Model Name:    iMac
      Model Identifier:    iMac8,1
      Processor Name:    Intel Core 2 Duo
      Processor Speed:    2.8 GHz
      Number Of Processors:    1
      Total Number Of Cores:    2
      L2 Cache:    6 MB
      Memory:    4 GB
      Bus Speed:    1.07 GHz
      Boot ROM Version:    IM81.00C1.B00
      SMC Version (system):    1.30f1
      Serial Number (system):    QP921090ZE4
      Hardware UUID:    20AE2D9A-DB71-54DF-95F7-DAEFEE167723
    I have a TON of art/photos on this computer. I'm wondering if backing my hard drive up with time machine gains me more space and processing speed-or if it only slows my computer down? is it better to house my files on a seperate drive from the drive i am using for backing up with time machine?

    Just to add a little, Time Machine is not a storage drive. Backups on there are not in a form you can use as you would from your normal internal. If you delete your pics etc. after backup, they won't be backed up on subsequent runs, and will eventually be lost when the TM drive gets near full and starts deleting the oldest backups. Have a read of Pondini's TM articles; http://pondini.org/TM/Home.html
    To do what you want, you need another drive to which you can simply copy your pics etc and open from there while booted to your internal. (this is a basic storage drive)
    The storage drive can then also be backed up to TM (provided the TM disc is big enough).

  • I do not have a high speed internet connection. How can I get Mountain Lion on a disk for install?

    I do not have a high speed internet connection. How can I get Mountain Lion on a disk for install on my 24" Imac?

    As long as you use your Apple ID to purchase it, I don't see why they wouldn't let you download the installer on one of their Macs and put it on a pocket drive.
    Or, a friend with a high speed connection?
    I agree with you about the delivery method, just trying to help you get what you want.

  • When our iPad is in use on the internet, my iMac internet connection goes off. I can't get the two devices to work at the same time with the AirPort Express. Is there a setting somewhere I may have missed?

    When our iPad is in use on the internet, my iMac internet connection goes off. I can't get the two devices to work at the same time with the AirPort Express. Is there a setting somewhere I may have missed?

    When two or more devices conflict it typically means that the DHCP service is either misconfigured or is not running at all. DHCP provides IP addresses to local network clients.
    Is your AirPort Express base station the only router in your current network configuration? That is, is it connected directly to an Internet modem and not to another router upstream of it?

  • How can I get the Firefox browser to work with my high speed internet?

    After switching from dial-up to high speed internet, I can no longer open the Firefox browser (which I was using) even after downloading the latest version. It is set for my default, but I can only use IE to browse. What else do I need to do to make it work?

    You didn't tell me it was a user name password issue.
    Open Keychain Access. (Applications/Utilities)
    Select Passwords on the left.
    Delete the Delta keychain.
    Now from your Safari menu bar click Safari / Preferences then select the Autofill tab. Make sure:  User names and passwords is selected.
    Navigate to the Delta site. Login with your user name and password. You should be prompted to save that info to a new keychain.

  • Upgrade to High Speed Internet Enhanced : Not working

    I recently upgraded my internet connection to High Speed Internet Enhanced (7.1 Mbps to 15 Mbps) from my old plan which had a speed of 1Mbps to 3.1Mbps. The order status indicates that the service has been activated. But still I am experiencing only the old speed (approx 2.5 Mbps only). Can anyone help?

    Could you post your modem's Transceiver Statistics for us? If you don't know how to get them, finding your modem make and model and posting it up will help us help you get them.
    One key thing to lay out on the table, if it isn't a stats issue it's possible 3Mbps/768kbps is your max speed due to your line coming from a Remote Terminal or DSLAM rather than the CO itself. Remotes are currently capped at 3Mbps, with the exception of a few meant to act as Mini-COs due to the lack of capacity going to them, and especially due to some of them being quite old. This is something for a person with the right level of access to the network or your account to find out. I've got someone who will check and turn up the speed if possible but we need to see the stats first.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

Maybe you are looking for

  • Why on close am I geting " firefox.exe -Application error - The memory could not be "written" "?

    Why on close am I geting " firefox.exe -Application error "The instruction at "0x00000000" reference menory at "0x00000000". The memory could not be "written" Click OK to terminate."? This is on Window XP A program White Smoke was loaded into this un

  • Neovo X 20 DVI issue

    Hope someone can assist with this... Having disconnected the monitor's Digital RGB input to connect a data projector, I can no longer get the G5 to show itself via the monitor's digital input...the analogue input still works via the VGA adaptor from

  • Session invalidated in JDeveloper 10.1.3.04

    Hi, I have a web application. It ran properly in JDeveloper 9i (embedded OC4J). When I migrated to JDeveloper 10.1.3.04. I always get error: session invalidated. The following is the detailed error message. Can some one help? 500 Internal Server Erro

  • Pulldown selection creates new text field in a form

    I have a set of dynamic select menus that are built using Kaosweaver's http://www.kaosweaver.com/extensions/details.php?id=88 Thanks to Kaosweaver, it works fine.  However, I was wondering how someone could have an extra text field popup in a form if

  • PO Creation with 3rd party number

    Hi Gurus, I want to create a purchase order with my own number which is provided from outside the SAP and not from the number ranges? IF yes kindly tell me what could be the possible way of doing that. Regards, Ankit