Low speed of the printing on Inkjet 2800

Hello!
I'm guy from Kazakhstan, so sorry for possible grammatical mistakes.
We have HP Inkjet 2800 in office. His speed of the printing is very low. Processing lasts around 1 minute...
This problem appeared since windows 7 was installed on PC (I'm calling it #1), which have connection with printer. Our printer was good when windows XP was installed. Other PCs are connected with PC #1 in LAN. PCs with windows 7 can print. PCs with windows XP have drivers for 2800 but can't print.
Also we used little Wi-Fi printserver to connect printer in LAN. It allowed to print from PCs with windows XP, but the speed of the printing was very low too (around 1 minute), even in case of 0.5Mb-sized files.
I have 2 questions:
1. Are there any variants how to provide normal speed of the printing (according to technical characteristics of the printer)?
2. How to provide work of windows XP and windows 7 at the same time?
Perhaps purchase of the additional device will help?
Yours faithfully, John_White

Hi,
Try these steps given below to help solve the issue :
Check the port setting: The port setting configuration in your system might not be set to ECP. See the documentation that came with the computer for information on how to change the port setting, or contact the computer manufacturer.
Check the printer software settings: The printer prints slower when Best or Maximum dpi is selected as the print quality. To increase the print speed, select different print settings in the printer driver.
I work for HP but my posts and replies are my own.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

Similar Messages

Is there any way to speed up the printing from my Mac to my HP LaserJet?

I just bought an HP LaserJet Pro 400 M451dn and it works wonderfully and prints amazing quality but the only problem is it takes a VERY long time for my MacBook Pro to send the data to the printer. It's suppose to be up to 21ppm but I was literally getting 2ppm. Granted it was a rather detailed page I was printing, but 2ppm is still way to slow. Used the generic PCL driver printed way faster but only printed in Black and White.
Specifics
Mac OS X 10.7.5
HP LaserJet Pro 400 M541dn
USB connected (about 12 feet)
Downloaded lastest driver and firmware from HP's website
Tried generic PCL driver, prints waaaaaay faster but only in Black & White.
I download something called GutenPrint but I have no idea how to install. If thats a good option and someone has instructions I would greatly apreciate it.
I'm not a tech wiz, but I consider myself good with computers.
Thanks in advance!

Gutenprint drivers are intended for non-laser printers. HP supplies the proper drivers, and you can download the latest version directly from HP's support site. Or you can install the most recent HP drivers provided by Apple.
Printing speeds do not include the time it may take to transfer data to the printer. It also doesn't take into account the time it takes for the printer to be prepared to start printing. Color is much slower than B/W.
Contact HP for any additional assistance you may need since these forums do not provide support for non-Apple products.

Crazy low speed from the off

hi all,
im a (relatively) new BT customer in a brand new build house. Before moving in i did some digging around to see what sort of speeds i could get with different providers and settled on BT as they seemed to be the best average and i preferred the BT home hub compared to the other ISPs offerings. (i would also add that im an IT engineer so did the usual **bleep** studying beforehand although whether this is a disadvantage remains to be seen)
i have been on the service for a month or two now and am getting dreadful low speeds. On average i get 750kbps down (max 950kbps) and 200kbps up. i have checked the disitance to the exchange with all the usual tools and its 0.9 miles away apprently. I have checked out all of my wiring and tried several ADSL filters but this is the speed i am stuck with.
I opened a case with BT and am getting the usual. (i would mention at this point that there is an issue with the BT site where you check what speeds you MAY get, if you're not a BT customer (which i wasn't) and you stick your address you get the 'up to 12meg' result, if you ARE a BT customer then you put your actual phone number in you get the REAL result. in my case i was advised i would get 'around 12meg' but then i was told i would actually get 'around 1meg', this is not good)
i am advised by BT that my exchange will get ADSL2 by the end of this year (2x-3x? ADSL) but im not counting my chickens. For info i came from a great 20meg cable connection in my old house so theres a big old step in the right direction
Im sure that this has been covered many a time on these forums so apologies if i just havent found my answers and feel free to just link me somewhere or copy and paste some jazz
anyone have any ideas or suggestions?
thanks in advance
David

As already been advised in bits and bobs:
The top tips for a good connection on a long line are as follows:
1) Is removing the bell wire as I have already advised and to have a good clean socket, with all the wires moved away from the connected wires, or snipped off all together, just to ensure as little interference as possible.
2) Would be to get a business hub, there are two available on Ebay, the 2701 (pictured right) and the 2700hgv (pictured left), now the 200HGV's seem to give a better sync speed by about 300kbps give or take, but I find they are less stable, whereas the 2701 decreases the sync speed but is far more stable, and good at holding onto low SNR's, I've seen it hold all night at -2dB Noise Margin and Im on a 9km line.
3) Would be to get a shieled RJ11 cable, as this can reduce the amount of interference, and also importantly it has the twists in as the telephone cables do to refract UV radiation, and Impulse noise just to name a few things. And the ends of them are gold plated with 24k gold just to ensure maximum transition .
Regards Edd
Check your Line
BT Speedtester

Bt infinity 2 low speed from the off.

Hello there, I upgraded to bt infinity 2 with home hub 5 a few weeks ago. My BT internet and wireless in the house had previously been quite good.
I was told the new cabinet could give me download speeds of 80mps.
Right from the off the speed with fibre-optic has been poor. Have been testing from the off and the download speed has been averaging out at around 40 (best ever 44mps). Upload has been averaging around 7. Ping reading usually around 30. Lowest speed was 3.6 mps upload!
Most of these test results were achieved with direct ethernet connection (which means a cable across the room so its not my ideal option). Wireless connection gives similar results. davolo home plugs have been the slowest of all - reducing speed to a crawl. Weird since they previously worked well with my old school broadband and are the 500mps type.
After a week of slow speeds and many phone calls and tests an engineer was sent out. He said the initial engineer had failed to establish the correct main socket which is outside the house. He did some work in there and went away saying speeds would gradually rise. Ansd that 80 mps wasn't realistic but something around 60 was do-able. Its now a week later and things have not improved.
I've enclosed 2 recent test/performance results. My line profile now seems to have very low projections.
would much appreciate any help/thoughts. Should add that I've not switched the hub on or off.
cheers again for the assistance.

many thanks for the prompt replies.
It would be great to think the speed will just rise after another week or so.
In case there is still a problem here is the data requested.
cheers
G

Reg:Low speed of the fibre link

Hi,
A strange issue has risen as few fibre links connected from core using STM1 and of 2Mbpsare showing following output and there speed is very slow,kindly help me find out the issue and help resolving the issue.Output of one of the links is as given below,
CORE#sh int Se1/1/0.1/1/4/3:0
Serial1/1/0.1/1/4/3:0 is up, line protocol is up
Hardware is SPA-1XCHSTM1/OC3
Internet address is x.x.x.x/30
MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec,
     reliability 255/255, txload 116/255, rxload 6/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Last input 00:00:01, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 12055
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 56000 bits/sec, 64 packets/sec
5 minute output rate 937000 bits/sec, 91 packets/sec
     1351190 packets input, 155951746 bytes, 0 no buffer
     Received 12974 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     751628 input errors, 94423 CRC, 54516 frame, 0 overrun, 0 ignored, 602689 abort
     1596894 packets output, 1478271189 bytes, 0 underruns
     0 output errors, 0 collisions, 11 interface resets
     0 output buffer failures, 0 output buffers swapped out
     9 carrier transitions no alarm present
VC 11: timeslot(s): 1-31, Transmitter delay 0, non-inverted data
Thanks,

Look at your interface counters. you have crcs, drops and aborts.
1. clear the counters on this interface & note the time you did so.
2. do a show interface at 15 minute intervals for one hour, then again 24 hours after the orginal clear counters.
    this will give you a measure of how bad things might be.
3. you need to then double check all the hardware from your router to the network point of presence clean connectors and verify light level.

Internet connecting at much lower speed lately

I have HSI Enhanced and have had it for 10 months at this location and for a number of years at my previous location. Last October I was connecting at 3360 / 832 kbps. After some months it went down to around 2800 / 832 kpbs. I wasn't crazy about speeds getting lower as time went on rather than the connection being improved, but it was pretty much free of disconnects and reliable so I was happy with it.
In the past month or so I had noise on my voice line which Verizon fixed, but my connection is now 1792 / 448 Kbps all the time, that is a drop I will not accept if this is the way it is going to be from now on. Also there is a lot of losing the connection, not to the DSL, that light stays on but the internet light goes off. I went through the usual channels online chat, telephone support to wherever that goes. I'm done with all that, that's good for people with trouble using their modem, etc. or can't connect it but not what I am looking for.
Finally they sent out a tech who was a nice enough person, what he did was call a central office and after them first claiming the lower speed was the right speed they put the connection back in the area of 3360/832. Then they said it will probably adjust itself to down around 2800 down, which it what I had before so I was OK with it. After several days with a number of disconnects (they don't last too long but very annoying) I am back to 1792 / 448.
I am using the same modem - Actiontec GT704WGB
I don't need a tech call here in the house again, nothing has changed in here since I moved in months ago. They can check the outside signal without me waiting around for them. They don't have to stand in here to call an office on their tablet.
I need to hear from Verizon personnel that can tell me LOCAL information about why my connection speed has tanked and why there are dropouts now. And most importantly, why it can't be the same as it was for all those months. As I said, I was happy with that - especially when it was 3360 / 832 kbps.
Solved!
Go to Solution.

When Verizon turns your speed back up, they have to disable the optimization system they use on the lines to maintain your speed, since it sounds like that is just turning your speed back down after a few days. Make them fix it back again.
For future note, if you do have problems with your DSL and you're also having audio quality issues with your phone, call Voice Repair, and leave DSL support out of the mix. DSL support usually dials back the speed for a line issue from what I've seen as a first try basis. If you do have noise that disappears when the DSL modem is off, then that could be from other things which DSL support OR phone support will be needed for.
Ex: Two years ago I had a problem with my Frontier DSL line having a ton of static on the line. The DSL modem was not synchronizing, however the noise stopped when I shut off the modem. It turns out, the night before lightning struck a tree outside of my home, and caused the DSL modem which was several years old to fry. The modem was still powering up, but the chip responsible for the DSL connection itself was blown. A new modem from Frontier via DSL Support fixed the DSL connection AND the static.
Ex2: At a local business with Verizon DSL, they hear static on their line from time to time, but only while the DSL is active. The problem was not with the DSL itself or any filters, but as the static got worse it began to show up without the DSL being connected. Voice repair was dispatched instead of calling DSL Support, and resolved the problem by running new cable between the building and the Verizon copper trunk. In addition, they found and corrected some corroding splices.
========
The first to bring me 1Gbps Fiber for $30/m wins!

I Can't Burn a CD any more! and a lower speed does nothing - HELP!

I have been burning CDs on this machine (imac 10.3.9) the same way for years and years. (7)
Up till last month.
This is what I get when I burn a playlist.
"itunes can not burn this cd because your burn speed is too fast for you cd burner or media. Choose a lower speed in the burning pane then try burning again."
I've tried that - even though that seems silly considering I've had no problems at my current settings until now. The lowest burn speed (1) gives me the same error.
I'm hating life and my mac right now, something I though I'd never say.
Anyone?

If you don't have Nero, check out http://discussions.apple.com/message.jspa?messageID=9229334#9229334. I think some people have found a way to get just the Burn Rights program.
If that doesn't work, some people seem to have luck with editing the registry or messing with filters or gear drivers. Check out this discussion starting with Tytus (he came up with the Nero fix) on March 22:
http://discussions.apple.com/thread.jspa?threadID=1939904&tstart=0
Hope this helps!

Read per axis status / run-stop don't work at low speed

Hello,
This is my fisrt motion program. I don't understand why the "read per axis status" don't send me the correct status for "run/stop" (only this status) when I run a low speed. The other status are all right. Impultions are still generated (In realyty motor run...)
I put a simple example to illustrate. Perhaps is it a wrong configuration in MAX but this seems unlikely. I can't join my Max config because ".nce" are not accepted in attached files.
Thank you wery much
Attachments:
One-Axis Move (Accel - Max Velocity - Decel) with read status.vi ‏26 KB

I realize this is an old post but wanted to post the solution in case others run across it. The reason the indicator is not working at low speeds is because it operates on a threshold. The default setting is for it to display false when running under 4000 steps or counts per second. Refer to KnowledgeBase 4XHD6DZY: Why does my Run/Stop bit not appear active while my motor is running?
Alex Person
NI-RIO Product Support Engineer
National Instruments

No image in the preview screen in the print module = gray print

I have been using LR for some time now. Today, in the middle of printing, I suddenly printed a grey print. It did have the copyright on it and contained a message in red "Out of memory Abe" in reverse in the lower right of the print. I started looking for the problem and noticed that there was no photo showing in the perview screen in the left most panel while in the print module. I restarted the machine, and cycled the printer several times - all no change and still printing gray.
printer is Epson 7800, OS is windows XP
thanks in advance

I have done this across several different folders, yet the problem still remains. Really odd that this is suddenly started in the middle of one of my print jobs.
Thanks

HP business inkjet 2800 Print black only option not showing in Windows 7 64 bit operating system

HP business inkjet 2800 Print black only option not showing in Windows 7 64 bit operating system
Please help, if any one knows any solution.

Hi @Firoskhan,
Welcome to the HP Forums!
I am sorry, but to get your issue more exposure I would suggest posting it, in the commercial forums since this is a commercial product. You can do this at HP Enterprise Business Community.
Hope this helps!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

HP Business Inkjet 2800 Printing Magenta Instead of Red

Hi,
We've got an HP Business Inkjet 2800 in the office that is printing magenta instead of red. I'm printing from Windows XP. I've aligned the cartridges and cleaned the cartridges, and still haven't been able to solve the problem. Any suggestions?
Thanks,
Cory

Hello mikesorr,
On the bottom of the ink cartridge is a small chip that the printer reads to help determine information about the ink. You may want to inspect that area to ensure it is clean and inspect inside the printer where the chip makes contact with the printer contacts to ensure there are no spillage or other debris which may cause the chip to not be read properly.
Also it may help to also post your question on the HP Enterpise Business Community since the product is a business model, the community there may have additional troubleshooting steps or other information that may assist you.
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

HP inkjet 2800 connected via USB only prints blank pages

I have a new Wndows 7, 64 but PC. My HP inkjet 2800 connected via USB only prints blank pages. What is wrong?

Not all printers are supported by the airport products alas. have a look here for a list of printers which are supported:
http://www.ifelix.co.uk/tech/8013.html

I received a low ink warning on my mac for my epson artisan 837 printer. I replaced the cartridge that was low but it still reads low ink on the mac but reads full on the epson control panel. I am also receiving a communication error between the mac

I received a low ink warning on my mac for my epson artisan 837 printer. I replaced the cartridge that was low but it still reads low ink on the mac but reads full on the epson control panel. I am also receiving a communication error between the mac

What exactly is the error?
And, we'd need some info re. your Mac model and OS version - you are not running iOS on it.
You need to realize that this model has been discontinued and the last driver updates are dated about a year ago. If you are running Mavericks, there may not be an updated driver for it. But you can try to delete the printer and add it again to see if that will work.

All my pdf files can be printed in low quality on my Brother printer but can't print in high quality in the printer menu.

My problem is that all my pdf files can be printed when I choose "low quality printing" in my Brother printer menu but cannot be printed in "high quality". When trying to print in high quality, the documents load in the printer tray and it says 1 document then disappears and 0 document printing is showing. I have some pdf files that I want to print in color in high quality and black and white but I'm unable to do so. It only prints in low quality for both color and black and white.

Hello,
1. Please make sure that your Reader is updated to 11.0.09. Go to Help -> Check for Updates.
2. Also, please check if there is any new update available for your Printer Driver.
Regards,
Anoop

My Lr5.7.1 doesn't recognize my Epson XP-760 printer and after customising the printout in the Print Module the Print options (lower right AND Main Menu Archive Print) are disabled

I am running Lr5.7.1 on an iMac Retina 5K (OS X Yosemite 10.10.1). My printer (Epson XP-760) works fine with all other applications but not with Lr!!! After selecting my printout preferences in the Print Module it works if I select Print File and save it to the desktop and then take it up as a Preview and print it from there. This is not what I want. I expect that the Print button (low right corner) should be abled rather than disabled and send to printer directly from within Lr's Print Module. It doesn't matter if the printer is on Wi-Fi or USB (or even both).
What is the problem? What else can or should I do to make it work as I expect?
Gunnar

Thank you very much, Modesto,
I have updated Yosemite to 10.10.2 and my problems remain. Reading About Lightroom 5.7.1, the pop-up window doesn't specifically say 5.7.1 and there is no choice to select More details (I can only trust that I am running really 5.7.1). I am sure that I really am Printing to file since this is the only choice I have ever seen enabled in my Lr5.7.1, whereas I have NEVER seen the Print option enabled. I enclose a screen dump (in Swedish) fyi.
So, I am still confused but on a somewhat higher level!
I really appreciate your help, Modesto
Gunnar

Low speed of the printing on Inkjet 2800

Similar Messages

Maybe you are looking for