Low speed via cable connection
So, I have this Airport Extreme 802.11ac wireless router (http://www.apple.com/airport-extreme/) and I can't get the advertised speed. My internet connection speed is 1Gb/s, but I can't get it from this router (via cable or wireless connection). I did >100 speed tests on http://www.speedtest.net/ with the router and the maximum speed was 217Mb/s. The maximum speed when I've connected my iMac directly to my ISP's internet cable was 926Mb/s.
Does anybody have the same problem?
I'd like to note that all cables for the router's clients and WAN are CAT 5e cables.
WAN to LAN throughput when the AirPort Extreme ac is set up in router mode is going to be in the range of 300-350 Mbps on a very good day. You might want review the test results below:
http://www.smallnetbuilder.com/tools/charts/router/bar/74-wan-to-lan
What speed do you see if you leave the AirPort Extreme connected to the Internet and then connect your Mac to one of the LAN ports on the AirPort Extreme?
It won't do much good to test wireless until you can get the WAN to LAN speed over Ethernet up to the 350 Mbps range.
Similar Messages
-
WRT54g v1.0 problem accesing it via cable connection
Hi i hope someone can help me.
I've got a WRT54g v1.0 and flashed the new firmware.
Via autoupdater and a cable connetion.
After reebooting and reseting i wasn't able to 192.168.1.1 via cable while using the wireless connection the access is possible.
I refashed via cable and the flash worked but still i cant access my
router via cable. Has any one an idear what might be the problem?Hi...as far as i know there is no known linksys auto updater for wrt54g v1.....so which auto updater you have used?? and what is the current firmware on the router??
the current firmware on the linksys website is "4.30.5"...if you have this firmware..then try resetting the router for 30 seconds and do a power cycle....force the card speed of NIC card of the PC to 10 mbps half mode...disable the firewalls...and check whether you can access the router now....
and also make sure that the wireless network you are connecting to is the wireless signal of your own router....meaning that you aren't connecting to your neighbour's network... -
New customer, v.low speeds. faster to connect to m...
Hi all.
As mentioned we are new customers to BT.
We only have one telephone socket in the house (the master). Which is connected direct to the incoming phone line.
We don't have a house phone.
The HomeHub 4 is connected into the test socket.
The hubs downspeed is 2mb and i am receiving 1.8mb over wireless (i know wireless is slower than wired).
If i connect to my nextdoor neighbours BtFon i can get about 3.6. We are far away from the exchange but is there anything i can do? We are unable to use iPlayer at such bad speeds. We keep checking when BT infinity is going to arrive but for the past 4 months it just says end of June.... end of July.... end of August.... end of Sept etc.
Any help is very very much appreciated.
Max1. Best Effort Test: -provides background information.
Download Speed
1.76 Mbps
0 Mbps
2 Mbps
Max Achievable Speed
Download speedachieved during the test was - 1.76 Mbps
For your connection, the acceptable range of speeds is 0.8 Mbps-2 Mbps.
IP Profile for your line is - 1.81 Mbps
2. Upstream Test: -provides background information.
Upload Speed
0.38 Mbps
0 Mbps
0.45 Mbps
Max Achievable Speed
Upload speed achieved during the test was - 0.38Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.45 Mbps
We were unable to identify any performance problem with your service at this time.
It is possible that any problem you are currently, or had previously experienced may have been caused by traffic congestion on the Internet or by the server you were accessing responding slowly.
If you continue to encounter a problem with a specific server, please contact the administrator of that server in the first instance -
Hi
This is my first time to use CAN.
I have LabVIEW 2010 and LabVIEW FPGA
I have NI 3110 Dual-Core Industrial Controller with Windows OS, NI 9157, NI 9852 CAN Low Speed Module and NI 9853 CAN High Speed Module to be used to monitor the CAN messages from an ECU unit.
The connection is done as the following:
· The High speed CAN is connected to the NI-CAN 9853 (Port 0)
· The low speed CAN is connected to the NI-CAN 9852 (Port 0)
· The baud rate of the 9853 is 500kbps
· The baud rate of the 9852 is 50kbps
· Both modules are set to “Listen Only”
· “Module Clock” in both modules is set to 20MHz
· CAN networks are 29-bit and 11-bit.
My consideration is to read all the messages from both modules without losing any message. Below is a picture from the block diagram on the FPGA target, is this the best way to read CAN messages from both modules? Also, could you please suggest what is the best way to read the messages on Host vi?
Unfortunately, I do not have the module right now to do some test, so that I cannot get the iteration time (“CAN Low Speed Loop” and “CAN High Speed Loop” show in the picture below), could you please tell how to calculate the iteration time needed for each loop depending on the above information.The way that you have proposed to use the CAN module to monitor the BUS is a bad idea. We have a prebuilt driver that will do most of this work for you. You will need to download and install the NI-CAN 2.7.3 and then you will be able to use the example finder. In the example finder look for.
The example finder is accessed through the Help menu.
Jacob K || Applications Engineer || National Instruments -
Internet connecting at much lower speed lately
I have HSI Enhanced and have had it for 10 months at this location and for a number of years at my previous location. Last October I was connecting at 3360 / 832 kbps. After some months it went down to around 2800 / 832 kpbs. I wasn't crazy about speeds getting lower as time went on rather than the connection being improved, but it was pretty much free of disconnects and reliable so I was happy with it.
In the past month or so I had noise on my voice line which Verizon fixed, but my connection is now 1792 / 448 Kbps all the time, that is a drop I will not accept if this is the way it is going to be from now on. Also there is a lot of losing the connection, not to the DSL, that light stays on but the internet light goes off. I went through the usual channels online chat, telephone support to wherever that goes. I'm done with all that, that's good for people with trouble using their modem, etc. or can't connect it but not what I am looking for.
Finally they sent out a tech who was a nice enough person, what he did was call a central office and after them first claiming the lower speed was the right speed they put the connection back in the area of 3360/832. Then they said it will probably adjust itself to down around 2800 down, which it what I had before so I was OK with it. After several days with a number of disconnects (they don't last too long but very annoying) I am back to 1792 / 448.
I am using the same modem - Actiontec GT704WGB
I don't need a tech call here in the house again, nothing has changed in here since I moved in months ago. They can check the outside signal without me waiting around for them. They don't have to stand in here to call an office on their tablet.
I need to hear from Verizon personnel that can tell me LOCAL information about why my connection speed has tanked and why there are dropouts now. And most importantly, why it can't be the same as it was for all those months. As I said, I was happy with that - especially when it was 3360 / 832 kbps.
Solved!
Go to Solution.When Verizon turns your speed back up, they have to disable the optimization system they use on the lines to maintain your speed, since it sounds like that is just turning your speed back down after a few days. Make them fix it back again.
For future note, if you do have problems with your DSL and you're also having audio quality issues with your phone, call Voice Repair, and leave DSL support out of the mix. DSL support usually dials back the speed for a line issue from what I've seen as a first try basis. If you do have noise that disappears when the DSL modem is off, then that could be from other things which DSL support OR phone support will be needed for.
Ex: Two years ago I had a problem with my Frontier DSL line having a ton of static on the line. The DSL modem was not synchronizing, however the noise stopped when I shut off the modem. It turns out, the night before lightning struck a tree outside of my home, and caused the DSL modem which was several years old to fry. The modem was still powering up, but the chip responsible for the DSL connection itself was blown. A new modem from Frontier via DSL Support fixed the DSL connection AND the static.
Ex2: At a local business with Verizon DSL, they hear static on their line from time to time, but only while the DSL is active. The problem was not with the DSL itself or any filters, but as the static got worse it began to show up without the DSL being connected. Voice repair was dispatched instead of calling DSL Support, and resolved the problem by running new cable between the building and the Verizon copper trunk. In addition, they found and corrected some corroding splices.
========
The first to bring me 1Gbps Fiber for $30/m wins! -
Connection issues and low speeds
Hi there,
my family have been with BT now for about 3 or so years and the connection had been rather good until about late last year. According to my family it's everytime I come back home from uni the internet starts to play up as in:
. Low speeds
.Drops out and loses connection
Believing it was somehow my laptop causing the issues I backed everything up and completly wiped it because BT support thought it may be a virus on my machine even the the checks came back with nothing. So I've wiped my laptop and restarted it like it was a brand new laptop...still we're having these issues so I refuse to believe it's my laptop causing the problems. I've changed the chanel on the hub so many times it just doesn't make a difference. Tried different DSL adapters tried different cables even a wired connection causes problems. I am begining to think it's because the router has had it but I am willing to try anything at this point before asking for a new router from BT. Even BT don't seem to know what the problem is all they do is reset the routers chanel every single time I ring them.
So any advice or help would be greatly appreaciated
Many Thanks
Benjamin
PS - sorry for any grammar/spelling mistakes , I've written this in a hurry before the internet drops out again...Hi Welcome to the community forums
Here is a basic guide to getting help from the community members done by CL Keith Please read through the link posted http://forumhelp.dyndns.info/speed/first_steps.html
once you have posted the information asked for then the community members can help you more
Thank You
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’ -
Many times my computer takes too long to connect to new website. I have wireless internet (time capsule) and I am running a pretty powerful real time financial work program at same time, what is the best solution? Upgrading speed from cable network? is it a hard drive issue? do I only need to "clean out" the computer? Or all of the above...not to computer saavy. It is a Macbook Pro osx 10.6.8 (late 2010).
Almost certainly none of the above! Try each of the following in this order:
Select 'Reset Safari' from the Safari menu.
Close down Safari; move <home>/Library/Caches/com.apple.Safari/Cache.db to the trash; restart Safari.
Change the DNS servers in your network settings to use the OpenDNS servers: 208.67.222.222 and 208.67.220.220
Turn off DNS pre-fetching by entering the following command in Terminal and restarting Safari:
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false -
My Canon MX 922 does not scan. My printer is connected via cable. Wireless doesn't work either.
My Canon MX 922 does not scan. My printer is connected via cable. Wireless doesn't work either. I get an error message with multiple suggestions but none of them apply to my situation.
I am so dissatisfied with this printer. I'm sorry I got it from Amazon because now it is a hassle to return it. I will never buy another Canon.
The printer menus are confusing. I hate using it. I loved my previous Canon which finally stopped working after many years, that's why I purchased a newer Canon model. Never again. Stick with cameras.
Marcy HotzThis note won't be as angry and frustrated as the last one...
Because I still had my old printer drivers and other applications on my hard drive, I think the application was trying to connect with the old printer. I deleted all the old stuff.
I also had several scanning applications on my drive which just confused me.
When I used the actual Canon MX922 application, I was able to scan but could only save as JPG, TIF or BMP (and one more, I forget which). So I did some research on the Canon site and found out how to save documents as PDF files using the Canon IJ Scan Utility.
It works now. So I'm satisfied, will keep this maching. I just had to take some time, sit down and focus on the problem. -
When I connect my Macbook Pro to my Dell DLP projector, either via cable or wirelessly, I just see a dark screen with the mouse and mouse trails only, can any one help?
jpmarkques post is a good start point, after folling his directions, you can try detect displays. Also try different rsolution and refresh rates.
Most of the projectors I have used support a 1024X768 res.
Youcan also try a pram reset if it still does not detect.
Leave theproctor connected and powered up, power down the MBP.
Power back up the MBP and hold the following keys before you hear the start up chime:
Option, command, P,R (no commas) continue to hold these keys till you hear the start up chime 2 times. -
Cannot connect via cable on Windows XP home SP2
Good Afternoon,
Maybe you can assist me here.
I cannot connect via cable my N91 (4 gb hdd) to Windows XP Home SP2. I can however connect via cable to my work computer which has the OS Windows XP Pro sp2.
In both cases both OS's are up to date, I have updated the phone OS to v2.10.013 RM-43. I am using the most up to date drivers that is available on nokia.com as well as the current ed of PC Suite (6.82.22.0)
The following is the steps I followed in both cases starting with XP Pro
1. Installed Drivers
2. Installed PC Suite
3. When prompted by PC Suite connected Phone via cable to Computer, further install steps were required. No reboot required. PC Suite then picked up phone
XP Home
Followed steps 1 + 2 in the same order
3. Connected N91 to XP Home computer, after driver install activity rebooted computer as requested. Disconnected N91 On reboot to desktop, in PC Suite I clicked on Get connected. Select Cable connection when prompted attached cable to computer and then to phone, on the phone select PC Suite. .
At this point I get the hour glass and nothing happens, Next is ghosted. It has been like this for 20 mins.
I have uninstalled both the drivers and the software. For some reason the updater can connect to the phone.
Can you advise on what I can do.Hi
Sounds lik ethe PC is having issues seeing it. Try this
/discussions/board/message?board.id=pcsuite&message.id=11480
Try this first:
1. Go to Windows' Control Panel and open "Add or Remove Programs" application.
3. Select "PC Connectivity Solution", click "Change" and then "Repair".
4. After Repair, restart PC
music -
Connecting a second computer to BThub 4 via cable
I do not think this is a BT problem but if any one has any advice it will be appreciated.
For a long time I have had 2 computers and a laptop connected through a BT hub 3. One computer (Vista) was connected by ethernet cable with the other two computers (windows XP) connected by wireless. Everything worked well.
Because hub 3 died I now have a Hub 4. However, I need to change the way my computers connect to the Hub. This means that there will be two computers connected by ethernet cable. The original computer connecterd by ethernet cable is set up just as it was prveiously and works well.
I connected the second computer with the ethernet cable supplied by BTand anticipated it would work. Unfortunately, for some reason I can't get the connection to work despite going through the wizard process of connecting from the computer both directly and via the small home network that is already establised.
One irritating thing is that, although I select a "direct cable connection" in the set up process, when trying to connect I get a screen stating dial-up failed and a retry is instigated. I am not using a modem!
I have tried re configuring things but to no avail, so getting to the end of my ideas, i wonder if anyone on the forum could give me some guidance.
Regards
DavidHi
Thanks to you guys for your help. the main problem was the absence of a net work card. This is now in place and I can make a connection tp the internet via the BT Hub. However, there is still one problem and this is as follows.
Computer A (windows XP) and computer B (Windows Vista) are connected to a small BT hub home network via ethernet cables.
On computer B (which has been successfully connected to the hub for about 2 years) clicking on network places > " view workgroup computers" shows a map which includes the BThub, it's self (B) and computer A.
If I do the same on computer A, it shows it's self but not the othe computer or the hub. Despite this it works perfectly well accessing the internet.
Because I need to transfer files via this network I need to see the othe computer(S) and open files on them, however, I have spent some time trying to establish the presence of other devices on computer A without success.
I have checked folder permissions are granted and I have tried to view the other devices with the firewall switched off but so far no success.
Suggestions gratefully received.
Regards,
David -
Is it possible to recover my data from iCloud backup without working wifi? I have as many other upgraded my iPhone 4S to iOS 7.0.2 with the result that the Wi-Fi or Bluetooth no longer works. However, i can connect to iTunes via cable but there is wrong version of backup.
Answer is no.
If you want the iCloud backup you have to have n internet connection, thus WiFi.
The not working WiFi has happened with quite a number of users.
It is not exactly clear what is the cause but there are suggestions to clear it up:
Some people have had success by removing an apostrophe from the iPhone name. If your iPhone is called something like “John’s iPhone” then this might work. Go to Settings > General > About > Name and change it to something with no apostrophe.
Some people have reported success by putting the iPhone into Airplane mode and then going to Settings > General > Reset > Reset Network Settings, but the problem may return.
You could also try going to Settings > Control Center and disable Access on Lock Screen then turn your iPhone off and on again.
Make sure that your router firmware is up to date.
Try backing up your iPhone and then restoring it. Check how to factory reset an iPhone for details.
If nothing is working for you, try contacting Apple or take your iPhone into an Apple Store.
Succes, Lex -
In case any Wi-FI is available and if I choose not to join wi-fi, on iPhone 5 it does not connect to my 3G cellular data network but it connects to 2G data network forcing me to lower speeds in Wi-Fi enabled areas.
This might help
http://support.apple.com/kb/ht3406 -
Mac Mini won't print via ethernet cable connected to airport extreme
Hi. Thanks for your input in advance. Am about to start throwing things around. I have an Airport Extreme based network which is working fine. The printer is a new HP L7590 which connects to the network with a USB cable connection to the Airport Extreme. Those with laptops and wireless cards are able to print no problem. However my Mac Mini, a 1.25 GHz PowerPC G4 is connected to the printer using a ethernet cable connected to the Airport Extreme. All was working perfectly until I upgraded from Panther to Tiger. I am now running 10.4.11. Now the Mini will not print. The jobs keep stopping. I have removed the printer and try to add it again. The print browser page finds the printer okay and lists it as connecting via Bonjour, but when you tell it to add it, it starts 'searching for new drivers' and then 'gathering printer information' and then it stops responding and I have to force quit it. Any suggestions?? I have already tried all the online mac help suggestions.
Actually it transpires that the G4 laptops are not printing either now.
-
Low speed connection, but still have input history.
Hi there,
We have done some tests in our business to see the performance difference between "low speed connection" being enabled and disabled for a system, both from a network perspective, and from a performance perspective on Citrix servers.
We have determined that the 'input history' feature doesn't cause much performance impact, but a lot of the other 'high-speed' features like images and tool tips do.
We would like to be able to have "low speed connection" for our system, but still enable 'input history'. Is there any way this can be achieved, such as through INI or registry changes?
Thanks,
Michael.I raised a message with SAP, and they responded saying that this is not possible
Maybe you are looking for
-
Handling unit creation in the out bound Process
Hi All, If we are not activate Storage Unit management/HU management in the warehouse and still create HUu2019s during outbound process via packing transfer order? We donu2019t want to manage stock at SU/HU level but create handling unit for
-
T410 - missing recovery partition
Hi everyone I've recently bought new T410 type 2537-A11 with WIN7 PRO sticker beneath a battery. Surprisingly, when I first launch OS, it appeared WIn7, but Home Edition. Moreover, I can't find recovery partition on hard drive!! I have no recovery di
-
How to set 2 points on each other in diffrent layers in easy way
Free transform, rotate, adjust angle and resize with fixed ratios; these are the steps I use to to set point A on 1 and point B on 2 every time, is there an easy way to do this metion ? please se the attached picture will help to explain what im doi
-
Java applet shows basket with ? (question mark) why?
Hi In one of the SRM Business Object . Approval preview shows as Question mark . but table wise it seems fine. why ? I wanted to know why i am seeing ? mark . i dont want this. i want get rid of this any help is appreciated. i wanted to recreate. any
-
I am not able to download apps on my iPad any longer. I get a message that says when I log into iTunes I will be able to download the app but there is nothing to download. This just started happening, I never had this problem before.