LR 3.4.1 does not filter hot pixels from Nikon D7000

Lightroom has so far been able to filter hot/stuck pixels from my old D70s raws quite well. For some reason however, it doesn't seem to recognize them in raw files from my D7000 and noise reduction leaves them completely untouched.
The camera doesn't really support mapping (except through potentially multiple multi-week customer support roundtrips), and the built-in noise reduction for long exposures effectively doubles the time per picture. It'd be really useful to have mapping from a static black frame in LR, or a despeckling/denoising method that picks up the "new and improved" stuck subpixels.

There were reports of "hot pixels" when shooting videos:
http://www.engadget.com/2010/12/22/nikon-d7000-firmware-update-released-cools-down-hot-pix els/
....and with still images:
http://www.photosig.com/go/forums/read;jsessionid=awkf4asZE9kc0r15__?id=245003
http://www.microstockgroup.com/cameras-lenses/nikon-d7000-sensor-problem/
There is a firmware update to fix or minimize the issue with videos, but that won't help your RAW still images. I downloaded your image file and most of the hot pixels are actually groups of 3-5 pixels at 150-180 level (out of 255) viewed in PS. I'd return it if you can, or take it in for repair under Nikon warranty. I am sure Nikon is well aware of this "quality control issue" (i.e. bad sensor chips).....Not acceptable! I tested my less expensive Canon 600D at 30 sec. and ISO 1600 and found no hot pixels above 35, all of which clean up nicely in LR with minimal luminance NR.

Similar Messages

LR2.7 does not bring up images from Nikon D7100

LR 2.7 does not bring up images from Nikon D7100 which I have just purchased. I have downloaded latest DNG raw converter 7.4 but does not work. The images come through fine in Bridge but not Lightroom. What is the problem?

Since camera makers insist on their own proprietary file formats, Adobe must provide support for each new camera as it is introduced. When a new version of Lightroom is released all development and support for the previous version ends. Your camera wasn't even mentioned or introduced when Lightroom 2.7 was released. Consequently, there can be no support for it. When you buy the newest camera model you should expect to also buy updated software to support that camera. In any event, the raw processing in the latest version of Lightroom is so far superior to what you have you really need to upgrade your Lightroom. You might consider using the Lightroom 5 beta until the official release.
Are you sure the DNG converter doesn't work? You only point it to the folder containing your raw files. The DNG converter doesn't list the contents of the folder. You will only see a list of your NEF files after you click the button to convert them.

Lightroom not fix hot pixels from my Nikon D7100

Hi there.
I have a problem with my cam D7100: there are tons of hot/dead pixels on the sensor.
I am going to bring this cam to the service center.
But I have a lot of images captured with this cam, and need to remove hot pixels from them.
One my friend say about auto-removing in Lightroom.
So I try Lightroom 4.4, 5.0, 5.2. No one can remove hot pixels.
(sample images are here:
http://www.ex.ua/get/327247286713/74274705
http://www.ex.ua/get/327247286713/74274765
http://www.ex.ua/get/327247286713/74274845
http://www.ex.ua/get/327247286713/74274919
iso 100-200-400-800, shutter 1/250)
Is this operation going automatically, or I need to chose some tools or options in Lightroom?
Please, help me somebody, cause thouthands of images are flaking!!!
Thanks a lot!

Nikon-User-D7100 wrote:
I understand, that I have camera's sensor issue, but I can't understand why Lightroom not "repair" that images?
LR actually does more than find and repair 100% level "stuck pixels," it also finds and corrects low-level hot pixels and higher-level "random" hot pixels. The problem is that you have "many" higher level hot pixels and LR's processing algorithm thinks they're image data. A different raw processor may work better or worse. Feel free to "trial" any of them and report back here what you find. Even with my 600D set +2EV higher in exposure (ISO 100, 1/30 sec. versus ISO 200, 1/250) your noise levels are much higher. IMHO you've got a defective camera!
(Click on image to see full-size)
Nikon D7100 ISO 200, 1/250 sec. Canon 600D ISO 100, 1/30 sec.

HT204655 Photos for Mac does not support semi professional camera Nikon D7000!

Since Nikon does not support USB storage mode, the (semi)professional line of Nikon cannot be used to import pictures!!
This is a serious flaw in the program. Aperture supports Nikon D7000, Image Capture supports the camera but the latest and greatest has forgotten all about supporting market leader's camera's?
The main and only reason NOT to use Photos... Or did I miss something here?

Sorry guys, forget all about it. I switch my camera off and on again (while it was connectoed to the Mac) and it appeared in Photos.
No idea what happened, but I can import my pictures.
Cheers,

Aperture does not recognise TIF files from Nikon CoolScan

The TIF files from my Coolscan are good in every other application, but Aperture does not recognise them. I've tried re-saving the TIFs as JPG and PDS but Aperture doesn't recognise any file generated from the TIF. Maybe it's something to do with the scanner driver? Any ideas how to load these files into Aperture?

You might check the color space that is assigned to the files. If you are using Nikon Scan software to manage your CoolScan, there is a preference for setting the color space of the saved file. FWIW, Nikon CoolScan .nef files are a 'raw' file, not camera raw, that was/is a Nikon proprietary format for their scans. If you use the Nikon Scan for image editing, the edits are non-destructive in saved files and can be adjusted by re-opening the file in NS. Adobe first made editing camera raw available in early 2003 and the Nikon format preceded that. Nikon's camera raw format also has the .nef extension, but is not the same as the CoolScan .nef-- really confusing. I suggested checking the color space, because Nikon has different internal names for Adobe RGB(1988) as well as their own Wide Gamut space.
All said, I've not had a problem opening .tif scan files in Aperture.

PhotoShop Elements 11 does not recognize NEF files from Nikon D600

Hi , I'm using PhotoShop Elements 11. while trying to open NEF files from Nikon D600 I'm getting message "Could Not Complete your request because the files appears to be from a Camera Model which is not supported....." . Now I tried to update but its showing software is upto date. Camera Raw version I can see 7.1.0.354. Please help me to solve this issue.
Thanks,
Jeet

You are not up to date. The latest version of camera raw is 7.4
Try again from Expert Mode
Help >> Updates

Not recognized raw files from Nikon D7000

Hi,
I have just bought a Nikon D7000 in stead of my D60. Now my Photoshop Element 9 cannot recognize the files/pictures, which I do not understand. Can anyone help me?

Hi,
That's strange, I have just managed to download it on a windows system.
As I said earlier, I don't have a MAC system so I'm not sure what to check there.
You could try this - it's the 6.3 update
http://www.adobe.com/support/downloads/thankyou.jsp?ftpID=4919&fileID=4578
Hopefully a MAC expert might jump in.
Brian

PSE7 does not support raw files from nikon d90

Can someone please help me , i have pse7 and just bought a new nikond 90 but i cant upload my raw files with pse 7. is there a patch with easy to follow instructions?
thanks
for any help
vanessa

You need the 5.6 camera raw plugin from here:
http://www.adobe.com/support/downloads/detail.jsp?ftpID=4626
MTSTUNER

Aperture 3.4.5 does not open raw files from Nikon P7800

Apple's list of supported cameras includes the P7800, but I get unsupported image format when I try and import nrw (raw) files. What gives?

Check your installed DCR version in the "About Aperture" panel and use Software update to see if a later version is available.
But I think you may be out of luck.
You indicate you are using OS X Lion, for which the last RAW update looks like 4.0.9 - http://support.apple.com/kb/ht4757
Support for the P7800 was introduced in RAW update 5.0.1 - http://support.apple.com/kb/ht5371 - which looks to be for Mountain Lion up.
Andy

RE1000 - Does not filter MAC ADDRESS

I bought this to extend the range of my new Linksys 3200, thinking that they would be compatible. Silly me! After spending 3 plus hours screwing around with this, I got online and happened to stumble on a post from another user, that stated that this device DOES NOT FILTER MAC ADDRESSES! So, if you want to use mac filtering you can't use this! Ridiculous! Some basic instructions to inform users of this fact would be helpful. But it comes with no manual or instructions whatsoever. Save your money.

I have a E2500 router, I was adding the Extender because of the size of the office. I set my router up to "Permit only" Mac IDs', right there I should have questioned why nothing worked. The Package & the base of the unit both had a matching MAC ID - to bad that the unit had a different one. I don't remember how much time I spent but finally disable the MAC ID Filter on the router and got the real one. From that point on, everything worked, I even was able to setup with the router internal security switch. Just think how a little thing like an ID would make an IT Guy just a little more mis-trustful, not count the grey hair.

Slider does not filter graph

Hi,
We just converted from 10g to 11g. I created a bar chart with a slider on month. The slider slides but does not filter the graph.
In the graph filter I have "month >= Jan. 2010 and month <= Dec. 2010", both values come directly from the month dimension table.
What have I missed?
Thank you.
June

user625912 wrote:
Hi,
We just converted from 10g to 11g. I created a bar chart with a slider on month. The slider slides but does not filter the graph.
In the graph filter I have "month >= Jan. 2010 and month <= Dec. 2010", both values come directly from the month dimension table.
What have I missed?Well, what does raise a concern is using strings for for date comparison. A date is not a string.
So irrespective of where/how/what your code is and does, make sure that dates are correctly evaluated - as dates.
If that predicate is part of a SQL statement, then it should look as follow instead:
month >= to_date( 'Jan 2010', 'Mon yyyy') and month <= to_date( 'Dec 2010','Mon yyyy')Note that the "+between+" operator can also be used (and is more readable too).
If the month value includes the day and the date can be the 31st of Dec and needs to be included in that range predicate, then use the last_day() function to convert +'Dec 2010'+ to the last day of the month.

Hp officejet pro 8100 and it does not print bar codes from UPS or USPS

have an hp officejet pro 8100 and it does not print bar codes from UPS or USPS. Can you please please help? i have used my ipad, by HP G62-355DX Notebook and neither will give me printed bar codes. The balance of the mailing label do print, just not the bar code. It may be my imagination, by I believe it used to print thebar codes.

Hi,
Try adding an alternate driver and try to print.
To use an alternate print driver for HP printers in Windows 7:
1. Click on the Start menu.
2. Click on Devices and Printers.
3. Click Add a Printer
4. Add a local Printer
5. Select Create a New Port
6. Select Standard TCP\IP port
7. Enter Printer IP address (Printer IP address can be found by printing network config page from printer
8. Under Manufacturer select HP and under printer select HP Officejet 8000 pirinter or Officejet 7410
9. Click apply and try printing
Although I am an HP employee, I am speaking for myself and not for HP.
--Say "Thanks" by clicking the Kudos Star in the post that helped you.
--Please mark the post that solves your problem as "Accepted Solution"

[Solved] The requested object does not exist. (Exception from HRESULT: 0x80010114)

I have a 8 node cluster with Hyper-V, which will be 10 nodes when it's finally done.
Recently I've been try to add nodes and though that went fine, after about a week I could not open the Failover Cluster Manager anymore.
After some checking I found out that the latest added node was giving problems.
VM's on the node still run and function properly, but most Powershell commands result in a "The requested object does not exist. (Exception from HRESULT: 0x80010114)".
I can suspend the node with Suspend-ClusterNode, but draining roles was unsuccesful in one case.
In the other there were no VM's on the node so suspending went fine.
What I did find out was that when I tried to ping the node from another, proper functioning node, it took a while before the pinging started. It felt like the interface had to come back online on the problem node.
After that, I could add the cluster to the Failover Cluster Manager. However, Powershell commands still give a 0x80010114 error or a CIM error for when I use Get-NetAdapter.
A reboot resolves the problem, but only for about a week.
I know there is a topic with the same title already, but the wbemtest en rollup update "answer" is totally unclear to me why I should change something with wbemtest, or why to install updates that to me have nothing to do with this problem.
Before I did the ping test from a functioning node I pinged my DC and another node from the problem node just fine.
No waiting at all.
The cluster has three networks. Management (host only), Live Migration and iSCSI (also a VMSwitch for certain VM's).
I have no idea where to look. Evenviewer doesn't give me anything I can work with that I can find...

Hi,
Are you using the HP servers? It seems is the HP Nic team service was causing the issue, please try to
disabled the HP NIC team service from services and restarted the WMI service.
The related third party information:
Advisory: (Revision) HP ProLiant Servers - Systems Running Microsoft Windows Server 2012 or 2012 R2 May Experience a Memory Leak Up To 5 Mb/ Hour for Some NIC Teaming Configurations
http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken&javax.portlet.prp_ba847bafb2a2d782fcbb0710b053ce01=wsrp-navigationalState%3DdocId%253Demr_na-c04209163-2%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.tpst=ba847bafb2a2d782fcbb0710b053ce01&ac.admitted=1401176219136.876444892.199480143
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

TS3276 My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that o2 account (offline) my mac I have no problem with my iPhone or mac laptop. any suggestions please.

My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that o2 account (offline) my mac I have no problem with my iPhone or mac laptop. any suggestions please.

Sorry for the delay...
I did what you've told me, new account and manually copied my files from Time Machine. I had lots of permissions problems, but at the end, almost everything is in order... It seems it had to be with some of the Apple Preferences, but I can't be sure, as most of them were dumped to the trash can.
I still don't have my Mail Rules back, unfortunately, although I did goggled some. It is a pity, as I had around 30 or 40 of them, getting my mail in order to each of its mailboxes, but it is a small price as the rest doesn't show the before syntoms.
Thanks for the help, anyway!!

HT1688 Messaging does not let me move from one conversation to another without going to the contact info of the person and choosing "send a message", then I can continue the conversation. I'm sure it's a setting I have made by mistake, but can't figure it

Messaging does not let me move from one conversation to another without going to the contact info of the person and choosing "send a message", then I can continue the conversation. I'm sure it's a setting I have made by mistake, but can't figure it out

Hi Elaine
Here si what I do:
Since I tend to message with teh same people I leave the messages available to me. If you are in one conversation with "Karen" and want to message with "Kathy" tap the message back arrow and select Kathy.
As always just be careful to rememeber who you are messaging to!

LR 3.4.1 does not filter hot pixels from Nikon D7000

Similar Messages

Maybe you are looking for