LSI Megaraid 9260/9261 driver issue on Solaris x86-64

We have several x4170 M2 machines with either the LSI 9260 or 9261 megaraid cards (same driver) where SUN uses the "SUNWmr_sas" driver, and you can download the latest driver from LSI website as "mr_sas". Using SUN Solaris 10 update 9 with latestl patches, x86 64-bit version .
Created two RAID arrays in the card BIOS (RAID1 using 2 disks and a RAID5 using 6 disks). Each disk is a 146GB 10k RPM SAS drive. The firmware on the card is the latest version from April 2011.
A copy from the RAID1 array to the RAID5 array yields a measly 5MB/s transfer speed. Tried both drivers with the same result. Tried all sorts of RAID array settings with no luck.
Installed Ubuntu Linux 10.04 LTS 64-bit version without touching the RAID array settings and the transfer speed jumped to over 100 MB/s (expected results).
Network copies to a single array and local copies within a single array perform as expected. Only the copy from one array to the other seems to be effected.
This leads me to believe the LSI driver for Solaris is at fault. Any thoughts? Anyone else noticing this poor performance?

Hi.
Read thread:
X4x70 (M1) with extremely slow disk I/O
Try workaround the problem by adding the following line to /etc/system and then reboot:
set idle_cpu_no_deep_c = 1
Regards.

Similar Messages

Small Business Server 2011 Essentials failed lock bios on LSI MegaRaid 9260 8i on Gateway GT350 F1

I had SBS 2011 Essentials on my Gateway GT350 F1 server setup in LSI MegaRaid 9260 8i Raid 1. I bought 2 x 900gb sas drives to replace the 2 x 300gb i have. When i try to install SBS 2011 Essentials i get a error message saying
failed bios
lock this installation media may be used only on hardware
Windows 7 installs without any problems. I updated the firmware of LSI MegaRaid 9260 8i. I also see that the OS Support for the mb is only till windows sbs 2008 R2. What i don't understand is how they got SBS 2011 Essentials to work and why can't
I re-install it.
Thanks

Maybe try OS installation using the "Smart Setup DVD" that came with the server. If you need to download it, it may be avaliable at:
Support Gateway Products
(Select your server by product name, select your OS [Win2008R2], then look under Applications tab)
http://www.acer.ae/ac/en/AE/content/driver-gw
Merv Porter
==========================

OSB Version 10.2 device driver issue on Solaris 10

I have a media server running 64-bit Solaris 10, fibre-attached SL500 library with two LTO tape drives. 'installdriver' appears to run without error but when I do
du -a /devices | grep ob | cut -f2
no 'ob' tape devices are listed.
All devices are visible following the 'probe-scsi-all' command.
There are plenty of 'st' devices created when I run 'installdriver', generally with name
st@w<WWN>,0:<bus name instance>
There is an 'sgen' device created with bus name instance 'changer'.
does this look OK? Should I be seeing 'ob' (rather than 'st') devices?
Some additional information.
This is a Sun T2000 server acting as both an Admin and Media server. I've tried running 'installob' but it complains that no 'ob' devices can be found, so this looks like a bug to me. The 'probe-scsi-all' and the devices created as a result of running the 'installdriver' command are shown in the output below.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2008.03.14 11:42:40 =~=~=~=~=~=~=~=~=~=~=~=
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0,1/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0,1/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0,1/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0,1/fp@0,0]ls -l
total 4
drwxr-xr-x 2 root sys 512 Feb 29 15:09 sgen@w500104f0009b8abb,0
crw------- 1 root sys 151, 0 Mar 14 10:25 sgen@w500104f0009b8abb,0:changer
drwxr-xr-x 2 root sys 512 Mar 14 10:25 st@w500104f0009b8ac8,0
crw-rw-rw- 1 bin bin 300, 256 Mar 14 10:24 st@w500104f0009b8ac8,0:fp0
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0,1/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0]ls
fp@0,0 fp@0,0:devctl fp@0,0:fc
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0]cd fp@0,0
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0/fp@0,0]ls -l
total 2
drwxr-xr-x 2 root sys 512 Mar 14 10:25 st@w500104f0009b8ac5,0
crw-rw-rw- 1 bin bin 300, 0 Mar 14 10:24 st@w500104f0009b8ac5,0:fp2
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0/fp@0,0]
[root@ukldvbsm01:/devices/pci@7c0/pci@0/pci@8/SUNW,qlc@0/fp@0,0]cd
[root@ukldvbsm01:/export/home/petes]
[root@ukldvbsm01:/export/home/petes]cat scsi_info
/pci@7c0/pci@0/pci@8/SUNW,qlc@0,1
QLogic QLE2462 Host Adapter Driver(SPARC): 1.24 11/15/06
Firmware version 4.00.26
Adapter portID - 10e00
************** Fabric Attached Devices **************
Dev# 0 PortID 10000 Port WWN 202500a0b838b13d
Dev# 1 PortID 10100 Port WWN 202500a0b838b18d
Dev# 2 PortID 10200 Port WWN 500104f0009b8ac8
LUN 0 TAPE HP Ultrium 3-SCSI M63S
Dev# 3 PortID 10f00 Port WWN 500104f0009b8abb
LUN 0 STK SL500 1201
/pci@7c0/pci@0/pci@8/SUNW,qlc@0
QLogic QLE2462 Host Adapter Driver(SPARC): 1.24 11/15/06
Firmware version 4.00.26
Adapter portID - 10e00
************** Fabric Attached Devices **************
Dev# 0 PortID 10000 Port WWN 202400a0b838b13d
Dev# 1 PortID 10100 Port WWN 202400a0b838b18d
Dev# 2 PortID 10200 Port WWN 500104f0009b8ac5
LUN 0 TAPE HP Ultrium 3-SCSI M63S
/pci@780/pci@0/pci@9/scsi@0
MPT Version 1.05, Firmware Version 1.09.00.00
Target 0
Unit 0 Disk SEAGATE ST973402SSUN72G 0400 143374738 Blocks, 73 GB
SASAddress 5000c50006f27d39 PhyNum 0
Target 1
Unit 0 Disk SEAGATE ST973402SSUN72G 0400 143374738 Blocks, 73 GB
SASAddress 5000c50006f28451 PhyNum 1
Has anybody ever got a T2000 to act as an OSB media server before? If so, how?
Message was edited by:
user625084

Thanks for the assistance.
I raised an SR for this and was pointed to the Release notes for 10.1.0.3 which has a description of how to set up devices on Solaris 10. Why these notes were not incorporated into the Install and Config Guide for 10.2 I don't know!

Unable to install Orable Enterprise Linux with LSI MegaRAID 8300XLP

I could not install Oracle Enterprise Linux on the PC with LSI MegaRAID 8300XLP
On the boot prompt, i typed "linux dd" with USB floppy driver, but it did not detect the driver.

I got the megaraid driver from fujitsu siemens and followed instruction from “Linux Driver for Primergy Servers” to create Linux driver image.
Note: mega_sas.ett, mega_sas.sh and mega_sas.biz
I formatted the floppy disk, then I run the script, mega_sas in Linux. The script will generate some files which need for LSI MegaRAID 8300XLP.
The three files (mega_sas.ett, mega_sas.sh and mega_sas.biz) have to be on the same directory.
RedHat 4 U4 x86 64 bits
On the boot prompt, I typed a command “linux dd ” with the LSI MegaRAID 8300 XLP driver image , and it detected the driver. I could load OS on TX150-S5.
Oracle Enterprise Linux x86 64 bit R4-U4
On the boot prompt, I typed a command “linux dd” with the same driver image which I used it on RedHat 4 U4 x86 64 bit, and it could not detect the driver.
During the installation, on the page which gives me two options for partitioning the disk,
“Automatically partition
Manually partition with Disk Druid
After I chose one of them, I clicked “Next” and I got an error message such as
“ No Drivers Found
An error has occurred – no valid devices were found on which to create new file
systems. Please check your hardware for the cause of this problem.
.

Solaris 10 and LSI MegaRaid 320 problem

I have problem with installation of Solaris 10 on LSI MegaRaid 320 SCSI controller....
Driver which in the solaris is SUNWlsimega and has VERSION: 11.10.0,REV=2005.09.15.00.24 and contains path
http://sunsolve.sun.com/search/document.do?assetkey=1-21-122829-02-1
Driver at http://www.sun.com/download/products.xml?id=431fd1be
has VERSION=11.10.0,REV=2005.08.08.12.43
and during install process always freeze at 97%....
how can i make floppy disk image with the latest driver or how can i set up driver from Solaris DVD?

Dear Sun manager!
Our competitors OS and their distributives - freeBSD and mandrake have a nice Support and a very advantages - complires an development tools!
I setup Solaris 10 systems on the IDE HDD - but thos is a first and last experiments with Solaris 10
I think that many users GNU OS and software take a high rate our " High support level"!
Good Luck

Cannot enter BIOS or boot from LSI MegaRAID SAS 9271-8i

Hello,
I have a LSI MegaRAID SAS 9271-8i installed in a C220 M3 (in PCIe1). When I go to CIMC, I can see the adapter there and I can create RAID arrays. I can set the first logical drive to be the boot drive too without a problem. If I boot from ESXi installer it will see the disks and install to them.
The problem is, the server won’t boot from the disks, and I don’t see any problems for the card’s BIOS during boot. I have disabled the on-board RAID controller.
How do I get the server to boot from the RAID card?

Hi,
Glad to see the issue is resolved now (I never saw your post before) was it that the OptionROM for the PCIe card was not enabled or the boot order was not properly set?
-Kenny

Mounting a Solaris x86 CD/DVD from a remote Windows CD/DVD-ROM drive

Greetings, all.
Is it possible to mount a remote Windows CD/DVD-ROM drive? I have the Solaris 10x86 Companion Software DVD sitting in a CD/DVD-ROM drive that's installed on a Windows server on my network. It is shared-out (F:) and the two servers can ping each other. I've also confirmed the NFS services/daemons are running on the Solaris x86 machine. I've tried the following variations but, all have failed to produce successful results:
# mount -F nfs x.x.x.x:/f /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f
# mount -F hsfs x.x.x.x:/F /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F
[FYI: S10_106_SOFTWARE is the DVD's label as reported by Windows Explorer.]
# mount -F hsfs x.x.x.x:/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/s10_106_software
# mount -F nfs x.x.x.x:/S10_106_SOFTWARE /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F nfs x.x.x.x:/s10_106_software /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/s10_106_software
# mount -F hsfs x.x.x.x:/F/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/s10_106_software
# mount -F hsfs x.x.x.x:/f/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/F/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/S10_106_SOFTWARE
I've also tried mounting it at bootup by adding the appropriate entry in the /etc/vfstab file but, this does not work as well. I've tried Google'ing for an answer to my issue but, I haven't been able to find anything that applies directly to what I'm reporting. It's usually chatter about mounting from one UNIX server to another. Any advice from the community would be greatly appreciated.

After three weeks, you deserve a reply. Windoze does
not natively support NFS.Also deserves a decent answer...
There are two ways to do this:
Install Microsoft's free "Windows Services for UNIX," which includes a Windows NFS server; or
Install the 'sharity' package (google for it); it provides Solaris systems the ability to mount Windows shares

UCS C240 M3 LSI MegaRAID VD Info

Hello,
I did replacement a new drive form a server(about 2 days ago and new physical drive number(slot) 6),
and I check storage log about new physical disk is rebuild finish and VD state change degraded to optimal from Cisco IMC.
But virtual drive's health is "Severe Fault" and also Overall Server Status same status.
I have to experience about replacement another C-series rack type server.
but I can't understand in this case. Is it bug?or something wrong?
Server : C240 M3(Ver : 2.0(1b))
RAID Card : LSI MegaRAID SAS 9271-8i
RAID Conf : SSD 2ea -> RAID 1
SAS 4ea -> RAID 10

can you share the "Virtual drive Info" tab?
-Kenny

C210M2 LSI MegaRAID has slot2 missing, where did it go?

CIMC doesn't have any errors, just seems the Slot:2
, SAS, HDD 135.972GB is missing in action
See attached screen show from MegaRAID BIOS Config Utility.
I have applied the latest host upgrade 1.3.1d.1

I swapped a known good 146GB drive into that slot. I then swapped the LSI MegaRAID card with a known good (I have a lot of spare parts:) and it seems to be the chassis drvie enclosure, which doesn't seem to be field replaceable. Calling TAC.

Sometimes my computer takes too long to connect to new website. I am running a pretty powerful work program at same time, what is the best solution? Upgrading speed from cable network, is it a hard drive issue? do I need to "clean out" the computer?

Many times my computer takes too long to connect to new website. I have wireless internet (time capsule) and I am running a pretty powerful real time financial work program at same time, what is the best solution? Upgrading speed from cable network? is it a hard drive issue? do I only need to "clean out" the computer? Or all of the above...not to computer saavy. It is a Macbook Pro osx 10.6.8 (late 2010).

Almost certainly none of the above! Try each of the following in this order:
Select 'Reset Safari' from the Safari menu.
Close down Safari; move <home>/Library/Caches/com.apple.Safari/Cache.db to the trash; restart Safari.
Change the DNS servers in your network settings to use the OpenDNS servers: 208.67.222.222 and 208.67.220.220
Turn off DNS pre-fetching by entering the following command in Terminal and restarting Safari:
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false

Very slow wine game/nouveau driver issue

Hello everyone, I'm trying to play a game (Civ 4) using wine. However, it was extremely laggy, and since it runs well on Windows (I have dualboot) plus it's not a very recent game and my laptop is reasonnably well-equipped, I thought it should work well on arch as well. Here is the link in the wine db. I should also add that I'm a very novice wine user so that might well be the (a) source of problem(s). Apart from the lagging, according to the sensors, the CPU's temperature rose from ~50°C to ~100°C within about A MINUTE.
I checked cpupower to see that the cpu was allowed to run at max speed and tried optirun to use the NVIDIA graphics card rather than the Intel graphics card I have installed. I'm by no means sure that the drivers are installed or configured properly by the way...
Starting with optirun looked to work (the loading screen came up) but when the main window should've been loaded, the application terminated with the following output:
err:winediag:wined3d_dll_init The GLSL shader backend has been disabled. You get to keep all the pieces if it breaks.
libGL error: dlopen /usr/lib32/xorg/modules/dri/nouveau_dri.so failed (/usr/lib32/xorg/modules/dri/nouveau_dri.so: wrong ELF class: ELFCLASS64)
libGL error: unable to load driver: nouveau_dri.so
libGL error: driver pointer missing
libGL error: failed to load driver: nouveau
libGL error: dlopen /usr/lib32/xorg/modules/dri/i965_dri.so failed (/usr/lib32/xorg/modules/dri/i965_dri.so: cannot open shared object file: No such file or directory)
libGL error: unable to load driver: i965_dri.so
libGL error: driver pointer missing
libGL error: failed to load driver: i965
[VGL] ERROR: glXCreateContextAttribsARB symbol not loaded
terminate called without an active exception
Before today I only used optirun for VLC (though I don't really see a difference) and to check whether it would run with glxgears. Neither case had any problems. I tried softlinking nouveau_dri.so from the "/usr/lib/..." to the "/usr/lib32/..." directory as well as copying it but neither helped.
Some info:
Graphic cards:
01:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M/820M / GT 620M/625M/630M/720M] (rev ff)
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
Packages:
local/xf86-video-intel 2.99.916-2 (xorg-drivers xorg)
X.org Intel i810/i830/i915/945G/G965+ video drivers
local/xf86-video-nouveau 1.0.11-1 (xorg-drivers xorg)
Open Source 2D acceleration driver for nVidia cards
local/nouveau-dri 10.2.8-1
Mesa drivers for Nouveau
local/bumblebee 3.2.1-3
NVIDIA Optimus support for Linux through VirtualGL
Some advice how to fix the driver issue or about what else might be causing the problems is greatly appreciated!

Besides agreeing with the notion above, you lack lib32-nouveau-dri and thus are unable to use acceleration with 32bit programs which is the undelying issue here.

Hard drive issues after update 10.10.3

Question also posted here:Hard Drive Issues (Both new and old)
I'm trapped in a HDD nightmare with my MacBook Pro mid-2012.
I updated to Yosemite 10.10.3 (with the Photos app). A couple of days after the update, I was watching a movie on my TV screen via HDMI. In the middle of the movie I removed the HDMI cable from the MacBook Pro and everything freezes. I forced shut down (Note: My HDD was encrypted). After I forced shut down, I tried to turn on and the loading screen would never stop loading - like, 14 hours stuck with the progress bar. Since I have backups, I decided to access DU and format my HDD. I tried everything. For real. Every command line I could type on Terminal to format, repair, erase and/or partition. I read almost every issue-related questions on the forums and stack exchange groups for a week (even posted my issue here: http://apple.stackexchange.com/questions/181090/erasing-and-partitioning-hard-dr ive-from-internet-recovery?noredirect=1#comment215695_181090).
So, I decided that it was a HDD failure and bought a new one.
I bought the Seagate 1TB SSHD Hybrid - ST1000LM014. Installed the new fresh disk and guess what? All those same problems again. I´m not able to restore from Time Machine because it doesn't recognize the disk in the restore page. But the disk is recognized in the DU. When I try to erase or partition the new SSHD, the same old errors: File system formatter failed. Yes, I tired GUID Partition Table, all of the security options, etc.
Please. Any light that you can throw at this issue, I'll be very grateful for. BTW, the new SSHD is recognized and the SMART Status says: Verified.
Any ideas on *** is going on?
Thanks in advance!
MacBook Pro (13-inch Mid 2012), i7, 8GB RAM

After I erase the hard drive (I assume one pass of writing zeros is good enough, 7 passes not needed?) do I turn off the laptop, then turn on and insert the Install Disk? Will there be a prompt telling me when to put in the disk? Or do I put in the disc right after erasing?
One pass is fine. If you've previously backed up your hard drive to an external hard drive using SuperDuper!, which is what I use and recommend, or another program, if it created a bootable drive, you want to boot off of it, bring up SuperDuper! and copy the drive back to the internal hard drive. SuperDuper also makes the drive bootable. When done, reboot, and you should be all set. If you're using Time Machine, you'll want to install the operating system, then restore the Time Machine backup. SuperDuper! is available from http://www.shirt-pocket.com/superduper/superduperdescription.html
Finally- should I update the OS? Is there a problem with the newest update that caused this crash, or was it just a spurious glitch/bad luck?
I've been running 10.5.8 for awhile with no issues, and would recommend moving to it.

Can you use a Mac Mini to share documents between several devices? iPhones, MacBooks, iPads, etc...? We are a home based business with several locations across the state and are having Google Drive issues, looking into Mac Mini options.

We are having Google Drive issues (some files won't sync) and it's causing us trouble with our business communication. Is there any way to use a Mac Mini to share documents between two people in different areas similar to google drive? Would this just be done through iCloud?

If you use Numbers, Pages and KeyNote it si very easy to sync those document among all the Apple devices. You need montain Lion on the Mac and at least iOS 5 on the mobile devices.
I show those document on my Mac, iPad 4 and iPhone 4S

Apple iPod USB Device driver issue on Win XP - syncing shuffle 2nd gen.

Hello fellow iPod shuffle users. Any of you run into this problem using the following configurations? Any advise/recommendations/workarounds much appreciated as I've burned 3 days on this issue and I'm still stonewalled.
I personally think it's a device driver issue/bug and am searching for a way to update my Apple iPod USB device driver for Win XP. Two brand new ipod shuffles (received for Christmas 2008) are both behaving this way, so the problem most likely points to a global software issue more-so than to shuffle hardware issue.
PROBLEM STATEMENT: Driver data i/o streaming issue does not allow shuffle to sync data with iTunes after initial sync (i.e. reading the content of the shuffle is good, but writing modified content fails). Posted error message "The ipod ... cannot be synced. Required disk cannot be found". After cracking the hood on my device driver, the problem seems to point to the Apple iPod USB device driver for Win XP. Driver will recognize the shuffle and read to it, but subsequent write attempts will result in device driver balks that "this device cannot start (code 10)".
ATTEMPTED WORKAROUNDS:
*Read All "How to Get Started Manuals" to make sure I was using the right technique for syncing my two shuffles from within iTunes... tried and failed
*Ensure only one shuffle was plugged in at a time (saw notice that two shuffles plugged in at the same time is not yet a supported config)... tried and failed
*The 5 R's as recommended by Apple Support... tried and failed.
*I've tried all 3 built in USB ports on my Lenovo T60. no love... tried and failed.
*Per discussion board: From Window's Device Manager-> Scaned for new hardware while shuffle was syncing...tried and failed.
* Per Discussion board: From Window's Disk Management -> Ensured shuffle came up as a FAT32 filesystem... connection tore down as quickly as windows recognized it.... tried and failed.
*From Windows Software config utility: Ran repair to re-install itunes 8... same results.
*From Windows software management utility: Uninstalled and reinstalled itunes 8... same results.
Hardware: IBM Thinkpad/Lenovo T60. Using build in k/b & no external mouse. Has 3 USB built in ports.
Software: Windows XP Pro SP2/iTunes 8.0.2/shuffle (2nd gen) driver 1.0.4 (same behavior using the original driver 1.0.3).
Apple iPod USB Device properties:
Driver Provider - Microsoft
Driver Date - 7/1/2001
Driver Version - 5.1.2535.0
Digital Signer - Microsoft Windows Publisher

Hi. Ive got pretty much the same problem.... Got a new shuffle for christmas..having real problems syncing with itunes. Funnily enough I managed to get 25 tracks on it but then it just stopped. error message says " The ipod shuffle cannot be synced. The required disk cannot be found." Ive done restore, and downloaded a reset utility thingy to try but still no joy.

Pixma ip6000d windows 7 driver issue. How do you get one?

Has anyone solved the windows 7 driver issue? The canon website does not have one yet is reported windows 7 capatable.

Hello ricksterofmi,
The PIXMA iP6000D Drivers are included with the Windows 7 Operating System through Windows Update. Please connect the PIXMA iP6000D to your computer and automatically install the drivers. Once this has been done, visit our website by selecting this LINK to download and install the Add On Module for full compatibility.
I hope this helps.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

LSI Megaraid 9260/9261 driver issue on Solaris x86-64

Similar Messages

Maybe you are looking for