Lumia 625 4G Stuck in airplane mode after flash fr...

while updating my phone OTA it's stucked and then i flashed it using nokia care suite.
after all finished and reboot the phone.and when its power up it's on airplane mode & cannot off the airplane mode.allways on when try off.i also tryed 8.1 update.but still no solution.
please help me

Did you try the Nokia Software Recovery Tool as well?
If you re-applied the firmware again successfully and you still have no IMEI in Windows Phone » menu » settings » about » more info – in that case, I would give my phone to my retailer, who in turn sends my phone over to local, but genuine Nokia Care for further inspection.

Similar Messages

Ipad mini stuck in airplane mode and won't reset

My ipad mini is stuck on airplane mode and I can't take it off. I therefore don't have access to wifi. It keeps asking me to enter my facetime login but I can't do that. It also won't let me reset the phone. Please help, any ideas?

Have you tried a restore in DFU mode? Sometime when a normal restore doesn't work, a DFU restore does the trick.
Entering DFU Mode on iPhone, iPad or iPod touch
Plug your device into your computer with a USB cable.
Turn off the device.
Hold the Power button for 3 seconds.
Hold the Home and Power buttons for 10 seconds.
Release the Power button but keep holding the Home button.
After about 15 seconds you will be alerted by iTunes saying that it has detected a device in Recovery Mode.
Make sure that when it says in iTunes that it is in restore mode that the iPad's screen is blank, that means it's in DFU mode.
Hope it helps

My iphone 5 is stuck in recovery mode after battery change?

my iphone 5 is stuck in recovery mode after battery change, I decided to change my faulty iphone 5 battery as i was out of warrenty, I managed to chance the battery with no problems (I Think), when i put the phone back together and tried to power on with the power button, nothing happened.! i connected to itunes and it powered on, displaying the connect to itunes screen (recovery mode) all was going well, the phone was restoring, the image of the phone restoring and loading up was displayed on the screen, when it finished it restarted but to show the connect to itunes screen again, it is stuck in the recovery loop. i tried the steps with holding the power and home button etc, none worked.! now when i try to restore, it extracts software but then, ' the iphone could not be restored, an unknown error occured (3194)' comes up, any ideas out there???? and Happy Christmas to Everyone ,

Hello Andyoneill9,
It sounds like you are trying to restore your phone but keep getting an errror message 3194. I want to recommend the troubleshooting steps from this article named:
Error 3194 or "This device isn't eligible for the requested build"
http://support.apple.com/kb/ts4451
Resolution
Important: If you see one of these messages and need help updating or restoring your iOS device, Install the latest version of iTunes and try to update or restore again. After that, follow these steps if you need more help.
Check your "hosts" file
After you've updated iTunes to the latest version, you can check the hosts file to be sure your computer can contact the update server. Use the numbered steps below if you’re on a Mac.
If you’re using a Windows computer, follow steps in this Microsoft support article, noting that resetting the hosts file will affect software services that rely on hosts file redirects. If you're using Windows on a business computer, consult your IT department to be sure applications will still work correctly after resetting the hosts file.
In the Finder, choose Applications > Utilities.
Open Terminal.
Enter this command and then press Return:
sudo nano /private/etc/hosts
Enter the password you use to sign in to your computer and press Return. You won't see text appear in the Terminal window when you enter the password. Make sure you use a nonblank administrator password.
Terminal will display the hosts file. Navigate using the arrow keys and look for an entry containing “gs.apple.com”.
Add the # symbol and a space ("# ") to the beginning of the gs.apple.com entry.
Press Control-O to save the file. Then, press Enter when prompted for the filename and Control-X to exit the editor.
Restart your computer.
Try to update or restore your iOS device again.
This is the first troublehsooting step to try, so there are additional things to try if needed you need them.
Thank you for using Apple Support Communities.
Regards,
Sterling

IPhone5s stuck in recovery mode after lots of times displaying blue screen of death, cannot restore it as iTunes displays error 14 on verification, same time phone crashes again with blue screen.

hi, my iPhone5s is only 3 months old, it has been like a whole month now since it started crashing, displaying the blue screen of death, since yesterday it was in the loop of restart-crash, and now it is stuck in recovery mode after lots of times displaying blue screen.
I cannot restore it as phone continues crashing again with blue screen, when iTunes displays error 14 on verification.
help please, this phone is all the means of communication I have.

It's a hardware problem. That's it. You shouldn't bother yourself with this situation. Just see an AASP.

[Zen Xtra] Stuck in Recovery Mode after updating Hard Dr

This is a long post, but I thank you in advance if you read it and think you have any ideas for me. Parts of this post were originally posted on the Nomadness.net forums and parts of it come from my personal email correspondence with one of the experienced users on that site.
Here goes:
I just installed a new HD on my Jukebox, and now I am unable to get it to download the Firmware (current or otherwise) and it remains in a state of rescue mode.
Here is how I posted my dilemma on the nomadness.net forums:
My computer is running Windows XP. I have a Nomad Jukebox Zen Xtra 40GB that I have had for about 2 years, and have had no problems with it, using it at least 8 hours/day 5 days/week (I run it at my desk while I work). I mention that just to give you an idea of how much regular continuous use it has been getting, if that matters. I have regularly downloaded all the latest appropriate firmware, etc. from the Creative website, using the auto updater service. I have one other Creative product connected to this computer, a SoundBlaster Audigy. This will come up again in a minute.
Over time I have accumulated so much new music that I knew I had to either get a new Jukebox or upgrade the HD. Since the Xtra is no longer available new, and upgraded ones are SO expensi've on eBay, I thought I would install a new HD myself. I read the instructions posted here on nomadness.net, and purchased an 80 GB 5400 RPM Momentus 5400.3 Ultra ATA/00 Internal Hard Dri've (that's Seagate).
Ok, now. The installation went easily enough, but now I cannot get the Firmware to reload. My computer recognizes that the unit is connected - it makes the appropriate sound when I connect or disconnect the JB, and under My Computer, there is the icon for the Nomad Jukebox Zen Xtra, under the "Other" category.
When I installed the HD and powered up, I got the rescue menu as expected and started with the "FORMAT ALL". I got the confirmation that it was reformatted and the expected GB of memory showed as available. SO...then I went to "RELOAD OS" and selected the "yes" option to verify that I wanted to reload via USB --BUT-- it only showed the "Start Firmware Update Now" for a second and then went right back to the menu. I have tried using the reset, and every combination of unplugging, replugging, removing the battery, putting it back in, reformatting, etc. and nothing changes. It just goes right back to the rescue menu every time.
I have the Firmware files (old and new) saved on my computer's HD, but when I try to launch any one of them, I get the same annoying message: "Your player is not connected, please connect your player". Well, if the computer thinks it's connected, then why doesn't the firmware file? I don't get it.
If I go back to the Creative auto updater on the website, it still recognizes the SB Audigy being connected, but no longer recognizes the JB.
How can I get the Firmware into the JB if I can't get it to recognize the player being connected? And why is that my computer shows it, if the Firmware file itself doesn't see it's
I received only one response that suggested I check the instructions on the Nomadness FAQs and also the great upgrade guide by Mr. Cheow, also on Nomadness.net.
This was my follow-up post:
Since I posted this earlier today, I have tried everything, and I mean everything, suggested by all of these "guides" to upgrading a hard dri've.
The problem remains that my computer recognizes the Jukebox as a portable device that is connected, but I am unable to get the Firmware file to load because it always says that my device is not connected. It should also be noted that the Nomad Explorer and other applications also will not recognize it (Notmad, JBHTTP, etc.)
Furthermore, I will add that we have two of the exact same model Jukeboxes and two of the same Dell computers running XP, etc. and in every possible combination we have tried, my Jukebox, with the new HD is the one that can not be accessed. So, I know that the connections, drivers, ports, etc. are not defecti've. The only thing that has changed since this morning is that I installed the new HD in my Jukebox.
I would love for any of you who have done this kind of upgrade to offer suggestions, as I am willing to try anything at this point.
After my last post, as a last ditch effort, my boyfriend suggested swapping the hard dri'ves in my Jukebox and his, thinking that perhaps we could get the firmware to download into his, and then switch the hard dri'ves back. Well, it looked as though it was going to work, and then the firmware update stopped almost as soon as it started and so, we are back to the same impasse. It?s the strangest thing, considering that both of us have been using our respecti've JBs daily, and have had no other problems? until I tried this.
We both racked our brains trying to think of a way we could get the firmware from the computer into the jukebox since it won?t load as long as it doesn?t recognize the player. Is there any workaround for this? By that I mean, is there any way at all to get the firmware into the Jukebox with out just launching it as a self-executing file? I know you can't just ?put? the file into the Jukebox, but is there any other means to extract it into the Jukebox so that I can use it's?
Any help you can offer would be most appreciated. I am worried that I have ruined my Jukebox and wasted $75 on a HD that I can never use?.
***Note on the Hard Dri've I chose:
I specifically chose this HD based on information posted by others on Nomadness
In particular, the newer instructions for upgrading a Zen Xtra hard dri've that were posted by an individual who used a 5400 for his own upgrade. I even emailed him with questions before I went ahead with this HD. As someone who has done this before, he felt that since this HD fits the specs of size and type being used by others doing this type of upgrade, including his own, that it would be fine. I honestly don?t think that it is the HD itself.
Since trying the swapping of HDs and Jukeboxes last night, we now have not one, but two, that are stuck in recovery mode and flash ?Firmware Problem? when rebooted. I don?t see how the HD itself could have done this. In fact, I am certain that the HD did not ?cause? the problem.
I have been reading forums about Jukeboxes (including here), anything I can find, looking for possible solutions. I have discovered that there are many people out there with the same dilemma, even those who simply updated their Firmware and nothing else, but now are stuck in the same frustrating place that I am.
***Note on the versions of the Firmware Update files I have tried:
I was going to use the newest one, but then after reading comments on Nomadness, I decided to try the older version that everyone was saying was less problematic. (see below) One of the posters had provided a link to it, and I copied it from there. I also had two other newer versions of the Firmware Update, including the newest one that has supposedly caused all the problems for others, but none of them would launch anyway ? I just kept getting that same message saying that the ?player is not connected?. Actually, to be more accurate, as I think I described in my original post on Nomadness, when I first tried to upload the firmware, it seemed as though it was going to go through with it, but never got further than one segment on the file progress display. On the screen of the player, it said it was upgrading, but after a few hours, it had gone nowhere.
Oldest - ZenXtra_PCFW__03_02_L6
New-ish - ZenXtra_PCFW_LA__20_08
Newest - ZenXtraP4SAudible_PCFW_LB_2_0_03
If you have read this far, then please know that I appreciate it very much. If you have any further ideas or suggestions, please reply.

Amazing that someone noticed this post and took a stab at it after over a year... Actually, I found my answer long ago, and have tried to go back and post?it'son several boards where I had been looking for the answer. It seems to be such a common problem that I figure someone else can surely use this solution as I did. I would suggest that anyone?who is experiencing the frustration of not?getting their computer to recognize their device?read the very enlightening and helpful page that I am linking to here:
http://www.misticri'ver.net/forums/showthread.php?t=30939? (this is from a forum for iRi'ver, but the info and fix are uni'versal)
This simple solution involves correcting the ENUM keys in the Registry (not as scary as you might think) and deleting all instances of your player from the Device Manager and then reinstalling so that Windows and other applications will all recognize your player again. It's so simple, and once I tried it, I was amazed that's all it took to fix the problem.
?I?suggest you read the whole page and follow the instructions as they are given. I deleted and re-installed my player several times and then rebooted a couple of times before it took effect, but then it did, and I was able to download the Firmware and have had continued success with my original player that I posted about as well as others I have acquired since I first posted that message in 2006. For reasons I have not yet identified, this problem still happens every now and again, sometimes when I switch between players to synchronize. It may well be that when I use my registry cleaner or some other utility that "fixes" my registry, that it resets this particular key - but as long as it's easy to fix, it's not a problem. Hope this helps others who may stumble upon this odd little problem with the Zen Xtra.Message Edited by TrixieInDixie on -05-200709:28 PM

IPhone stuck in recovery mode after failed update.

Hi, I have a bad situation here... My iPhone 5 got stuck in recovery mode after I tried to update to iOS 7.1.1 from 7.0.4 and it failed (error code 6). If this was my iPod touch I would just restore it because all I have is music, but this iPhone has all my sisters graduation photos, important photos, important school documents, contacts, app data, videos from concerts. Etc. I was wondering if I could get the photos off the phone before restoring it, because they are important. I know I should've backed up my photos and made a backup of the phone, but I've been really busy with a lot of stuff. So I was just wondering if there is any way to get the photos and app data back. The app data doesn't really matter but the photos do. The device was not jailbroken or hacked in any way.
If you could help, tell me ASAP.
-JP

When your phone is in recovery mode, it's like it crashed. The only way that you can get it out of recovery mode is by restoring, and this erases all your data as well.
You can believe what you wish by "reading all over the internet". This is Apple's technical support forum. We do know what we're talking about.
since you have very important photos on your phone, why haven't you been importing them to your computer as soon as possible after taking them? This is how the phone is meant to be used. Keeping critical data on only a device which can be easily stolen, dropped and broken is just plain foolish. Also, did you not back up your phone (as you should be doing with any computer) before attempting any operating system update? As you've now just painfully learned, updates do not always go as planned.
I'm sorry for your data loss, but let this be a very important lesson. BTW, when was the last time you backed up your computer? I'm sure you have important data on your computer. Hard drives WILL fail.

Iphone stuck in emergency mode after downgrade from 4.0.2 to 4.0?

iphone stuck in emergency mode after downgrade from 4.0.2 to 4.0?
Upgraded to 4.0.2 last night. Immediately, itunes would no longer detect my iphone. Decided I had to downgrade back to 4.0 again. Learned I cannot do that easily, so i found a .ipsw file of firmware 4.0 online, and downloaded it. Started up my iphone attached to itunes in restore mode, held down shift, and clicked restore button. Successfully restored the 4.0 file I had downloaded.
At the first boot, it was stuck in emergency mode. I even tried to restore the default itunes backup after that, it was still stuck in emergency mode.
Anyone know how i fix this iphone? I have no interest in jailbreaks, i am in a 2 year contract with AT&T.

omg, it just fixed itself! i installed a brand new itunes on my laptop (which has never had itunes app before)
plugged in my iphone, it detected it right away and said "activated"! my phone is working again and has its phone number back.
now i did notice that the 4.0 is indeed slow, so i do want to try going back to 3.1.3 also.

My iphone 5 is stuck in recovery mode after trying to update it and know it wont sync to my computer to fix it.... help

my iphone 5 is stuck in recovery mode after trying to update it and know it wont sync to my computer to fix it.... help

Hello richardayoub1,
Thanks for using Apple Support Communities.
If your iPhone is in recovery mode, you will need to restore it with iTunes.
Use iTunes to restore your iOS device to factory settings
http://support.apple.com/kb/HT1414
Take care,
Alex H.

HT4623 Stuck in recovery mode after update. What do I do?

Stuck in recovery mode after update. What do I do? Tried holding both buttons and releasing after screen goes black. Returns to recovery screen.

Hi there Rosie Bud,
You may find the troubleshooting steps in the article below helpful.
If you can't update or restore your iOS device
https://support.apple.com/kb/ht1808
-Griff W.

Ipod touch stuck in recovery mode after update

Help! Ipod touch is stuck in recovery mode after an update. I don't want to restore and lose all pictures.

You have no other choice but to restore. You can restore from backup and get the iPod back to where it was when the backup was made.

My phone got stuck in recovery mode after update to IOS 5.0.1, how can I solve it ?

my phone got stuck in recovery mode after update to IOS 5.0.1, how can I solve it ?

Read this
http://pathumf.blogspot.com/2011/11/how-to-reboot-stuck-iphone-iphone-4s.html

Our iPad is stuck in recovery mode after attempting to update.

Our iPad is stuck in recovery mode after attempting to update to latest iOS..Help.

It IS plugged into the pc. iTunes doesn't even recognize hat any device is connected.
Reiboot isn't even working. considering trying DFU mode. no idea if that will even help.

Ipad 2 stuck in Recovery mode after trying to upgrade with ISO6

Ipad 2 stuck in Recovery mode after trying to upgrade with ISO6, help!

Restore ur iPad to iOS 5 or 6( if u have downloaded)
<edited by host>
Then connect your iPad to your computer ,open iTunes ,click on your iPad's name in the left column ,hold the shift key and press restore , chose the file u downloaded , Wait for the restore to finish.
Then set up your iPad as a new iPad .
Here you go, Now your iPad will be perfectly fine..

Ipad 2 stuck in recovery mode after updating to IOS 5, Unknow error -1

Hi Everyone,
my Ipad 2 is stuck in recovery mode after updating to the latest IOS 5. Tried to restore, it comes up with unknown error -1.
Ive tried all that I can including the tips given in the apple forums and internet. Please help.

Hello soccerlime,
Thanks for using Apple Support Communities.
The error code "9006" in iTunes when updating or restoring your device indicates that access to the iTunes update servers is being blocked. Please take a look at the information below to help resolve this error.
Check your security software
Related errors: 2, 4, 6, 9, 1000, 1611, 9006. Sometimes security software can prevent your device from communicating with either the Apple update server or with your device.
Check your security software and settings to make sure that they aren't preventing a connection to the Apple servers.
Resolve iOS update and restore errors
Take care,
Alex H.

IPhone 5 stuck in portrait mode after upgrade to iOS 8

iPhone 5 stuck in portrait mode after upgrade to iOS 8.
Phone was fine before the upgrade, iOS 8.1 did not fix the issue.
Have done a factory reset at Genius bar and they say it's a hardware issue and have gotten this response below:
"Now, when you perform an update to any iOS device many system checks are run to verify that all components are working as they should. This is part of the firmware update process. When these checks are run sometimes issues are detected, even if all seemed to be running well previously. When this happens one of two things can occur. Either the hardware will be deactivated completely, or it will be locked in a state of use so that the device can still be used. In the case of the gyroscope for screen rotation, the firmware locks in place so that while not perfect, the device can still remain on some functioning level. This is what appears to have happened when you updated. The software itself did not cause any failure, but it detected a currently upcoming issue and prevented it from becoming worse."
All I want is a replacement but they want me to pay £199 since it's out of warranty.
Anyone have the same issue?

If the device is out of warranty you must pay the out of warranty replacement fee to have your iPhone replaced. If the phone was still under warranty the phone would have been replaced at no charge.

Lumia 625 4G Stuck in airplane mode after flash fr...

Similar Messages

Maybe you are looking for