Lvrt.dll error in application

Hi, I have built an application from my development PC and I am running it on a target PC. The application crashes regulary on the target PC, within 20 min. Windows displays an error measage that states that lvrt.dll caused the failure. I have been searhing the forum for answers, and found other people with the same problem, however there were no clear solutions to the problem. Does anyone have a solution?
My labview version is 8.5.
My hardware is a CompactDAQ chasis, with modules 9472, 9265, 9205. Moreover I am reading out temperatures from an Agilent 34970A though a GPIB interface.
With kind regards,
Jesper

I too have been experiencing this problem, only with 8.2. I have
a built application that crashes semi-randomly on my development
machine - XP blames LVRT.DLL. I bundled the 8.2 LVRT.DLL into my
build as suggested, that didn't help. The application thus far is
just a fairly complicated GUI with no hardware being addressed (yet)
and no external libraries being called (yet).
Insight, anyone?
Thanx.

Similar Messages

LVRT.dll error everytime I build a deployment

HI all,
I have struggled with this for 2 days now and tried to use the forum to figure this one out, but I cannot. I have built quite a few deployments before, however, when I try to put a new deployment on a clean Win7 32-bit PC, I get the same issue:
Whenever I try to run the deployment I get the lvrt.dll error...please see JPEG. I am not sure why I am getting this. However, I have two concerns that may be causing it.
1. If you look at the error, it is looking in the Program Files (x86) folder....I don't have that folder on my Win 7 32 bit machine....only Program Files.
2. It seems like when I run the deployment, it is totally skipping the model. I believe this because the error it gives is for a sequence in main, and I have a vi call in the model. However, i do have the cfg folder in my workspace.
Any ideas?
Thanks,
Ryan
Attachments:
error.jpg ‏105 KB

Hi, I am using 4.2. I believe I have solved that issue. It was an issue with the wrong engine below loaded.
However, I am stuck here now. When I build, I get the following warnings, and I cant seem to solve it. Please advise. I realize it wants me to add some paths in the search directories but I'm not sure exactly what it should be.
Thanks,
Ryan
Warning: There is no relative path between the following files. You may need to add a path to your search directories.
From [TestStand]\Components\Models\TestStandModels\FT_ParallelModel.seq to [Installation Directory]\vi\user_stats.vi
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\SeqEdit\layout_Small Screen Example.bin
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\SeqEdit\layout_Large Screen Example.bin
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\Users.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\ToolMenu.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\TeststandPersistedOptions.opt
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\TestStandModelReportOptions.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\TestStandModelModelOptions.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\TestExec.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\Templates.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\StationGlobals.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\PLPropertyLoader.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\Filter.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\EngineParts.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\DeploymentUtilityOptions.ini
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\DeploymentUtility.log
From [Installation Directory]\TS\MF_Final_Test.tpj to [TestStand Application Data Directory]\Cfg\Deployment Utility RecentFiles.ini
+++++++++++++++++++++++++++++++++++++++

Lvrt.dll Error

I am using the LabView RTE 8.2.0.4002 to execute a LV app that was built in LV 8.2. My app sporadically crashes. The output error file says the error is in TDUtility.cpp (1432) and sometimes (1041), Unexpected: 8, 4, tc: 48, 48. The PC Event log just reports that my application died and that the faulting module was lvrt.dll version 8.2.0.4002. The Microsoft error log shows that I received an Exception Code: 0xC0000005. My file reports the OS is Windows NT, OS Version 5.1, but the PC is running Windows XP, Service Pack 2.
Any ideas?
Solved!
Go to Solution.

Hi bfieldi,
I am not sure what the Unexpected: 8, 4, tc: 48, 48 message is referring to, but I wouldn't think it would be a typecast. Try the ideas that Karunya posted if you can, and if you want to send your error log in to National Instruments, you can choose to report the error when you get your TDUtility.cpp message. This will supply more information about what is happening.
Regards,
Stephen S.
National Instruments
Applications Engineering

Lvrt.dll error on Windows XP

I had an application built using LabView 5 on Win98 system and it was running perfectly, I decided to upgrade the system to Windows XP,then, i used Labview Run-Time Engine 5.1.1, i was surprized when the application ran perfectly also (I know that 5.1.1 works only till Win2000!!!), BUT, after 10 to 15 minutes from idle process, i get an error from WinXP saying that there was a problem in my exe file because of (lvrt.dll), when i restart the application it runs OK.
I'd like to add more info:
- The application is using Traditional DAQ Card.
- The application includes ActiveX & Networking.
- I don't have the source code to modify anything.
Any one has a clue what to do to avoid this error????

Thanks Jeremy, But i have to use a powerfull machine with high configuration, the processor of the machine is 800 MHz Bus Speed, which the 98 can't run on, so i have to use either 2000 or XP, i forgot to tell you that on 2000 i get an error when i try to start the application and when i click ok, it runs perfectly !!!! kind of complicated isn't it????
I can't come up with a solution, can any one????!!!!

Build dll error in application builder 8.6.1

Hello,
I get always an error in the LV 8.6 application builder, when I build a dll. There is only one function in it, that has a string and an error input, and nothing else. I attach a screenshot of the VI prototype, and hier is the error description:
Error 1 occurred at Building DLL.
A component needed for Application Builder does not support the required functionality. This might have been caused by installing an older version of LabVIEW after this version was installed. Reinstall the current LabVIEW version to correct this issue.
Possible reason(s):
LabVIEW: An input parameter is invalid. For example if the input is a path, the path might contain a character not allowed by the OS such as ? or @.
=========================
NI-488: Command requires GPIB Controller to be Controller-In-Charge.
After that I reinstalled LV8.6, I tried to reinstall only the 8.6 app builder, but no success.

Hello,
thank you for the reply.
I have solved the problem. I uninstalled the last installed LV version, this was 8.0. Then ran appbuilder again in 8.6, then I have got an instruction to run applibs\lvdllbuilder\lvdb.exe. Since then works.
regards
Mitulatbati

System error message and application crash - ModName: lvrt.dll Offset: 00080a6a

I'm running into an error message which is proving particularly difficult to debug. After my built application has been running for some time, a windows system error will pop up telling me my application has done something bad and needs to be shut down (and sorry for the inconvenience). Clicking through to the "see what the error report contains" page reveals the issue as being in the lvrt.dll module at offset 0080a6a.
This unfortunately doesn't mean much to me.
On some occasions when I click "Don't Send", another error message pops up informing me there is "Not enough memory available to complete this operation".
The program will typically run between 8 and 24 hours before the error occurs, though I've had it run error-free for upwards of 48.
My program is unfortunately fairly large, and depends on communication with proprietary hardware so can't be uploaded in a functional state. In general terms, the body of the program (which is executing when the error occurs) involves RS-485 serial communication and simultaneous display of data to 7 continuously updating strip charts (producer-consumer design), along with envalope detection and RMS calculations in real time, all of which is multiplied by two parallel channels (around 1Mb/s data rate for each). The data is also buffered and stored in binary files for later review. Binary files are closed and a new one is opened for every 10 minutes of data collection (approx 50MB of data).
There are also about 40 user controls associated with each channel, and are polled periodically (a couple times a second). The crashes occur during over night tests, however, when there is no user input. Globals are used for inter-panel communication, but no global is written to in more than one location (most are read in multiple locations).
I know this is a bit of a shot in the dark here, but does the lvrt.dll error at offset 00080a6a mean anything to anyone? Are there any "typical" causes for a failure in lvrt.dll having to do with prolonged high data rate serial communications? For reference, this has occured on multiple machines, but all the machines it has occured on are identical out-of-the-box laptop models running XP 32. I'm going to try to run an overnight test tonight on the development machine and see if I get any different results (Vista 64 vs Windows XP 32).
I can't say my hopes are high with this one, and I'm gonna continue to comb over the code for any possible conflicts, but any insight would be appreciated.

Claire,
Next time the error message comes up I will take a screenshot of it for you. Unfortunately that may not be until Monday, as tonight is the soonest I'll be able to run another long-term test. The time between failures is the most frustrating part to debug!
There are no errors on compiling or building the application in LabVIEW. My testing has been done mostly on the distribution laptops in application form, with no LabVIEW dev tools installed, Windows XP 32 bit.
The overnight test I attempted on the development machine (within the LabVIEW environment) welcomed me the next morning with a rebooted machine, and so I wasn't able to see an error message (if there was one). Vista 64 on the development machine. Reviewing the data files, I got about 9 hours worth before the crash.
Given the time between failures and the large volume of data I'm passing around, this seems like memory leak type behavior. I'm a bit confused by the fact that it seems to fail in lvrt.dll every time, though. I'm don't know what that indicates, if anything.

CS3 on Vista: VersionCueUI.DLL error

Hello,
when I tried to open .ai files I worked on yesterday this morning I got a VersionCueUI.DLL error:
The application ran out of virtual memory. Please close some windows to free memory.
After this Illustrator tries to shut down but freezes in the process untill windows asks if I want to wait or shut it down.
I checked the files on my laptop and was able to open them. Specs of my desktop:
Intel Core 2 Quad Q8300
4 GB RAM
670GB remaining disk space
NVIDIA GT120 1024MB
I am working with the CS3 version of Illustrator which I installed yesterday on my new computer which has Win Vista preinstalled. Everything worked fine untill this morning, when I tried to open the files which are all around 10MB in size.
I installed the last updates of CS3. Is this a problem caused by the last update(s)?
Sincerly,
Martin

See http://www.adobe.com/go/kb403266, the document is for Photoshop, but the solution is the same.

Application crashes in Windows 7 64bit made in Labview 2010 sp1 f2 with Fault module name%3A lvrt.dll%2C version 10.0.0.4033 and exception code c0000005

I build an application exe and then its installer along with run time environment.
The installers instals the application correctly but when I try to execute the application, I get an error that application has crashed and Windows must close it down or search for solutions online with this additional information for the crash.
Problem signature:
Problem Event Name: APPCRASH
Application Name: AGMS.exe
Application Version: 1.3.0.0
Application Timestamp: 4c24e8f5
Fault Module Name: lvrt.dll
Fault Module Version: 10.0.0.4033
Fault Module Timestamp: 4c9273f4
Exception Code: c0000005
Exception Offset: 00005310
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
I am using labview 2010 sp1 32 bit on a 64-bit machine, with the following specs
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.130318-1533)
Language: English (Regional Setting: English)
System Manufacturer: Dell Inc.
System Model: Dell System XPS L502X
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz (8 CPUs), ~2.0GHz
Memory: 8192MB RAM
Available OS Memory: 8106MB RAM
Page File: 3457MB used, 12753MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
The exe /application runs fine on my PC but when I try to run it on another PC it crashes. The other PC has similar specs as given below
Operating System: Windows 7 Ultimate 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.140303-2144)
Language: English (Regional Setting: English)
System Manufacturer: LENOVO
System Model: HuronRiver Platform
BIOS: Default System BIOS
Processor: Intel(R) Core(TM) i3-2330M CPU @ 2.20GHz (4 CPUs), ~2.2GHz
Memory: 4096MB RAM
Available OS Memory: 4010MB RAM
Page File: 1359MB used, 6658MB available
Windows Dir: C:\Windows
DirectX Version: DirectX 11
DX Setup Parameters: Not found
User DPI Setting: Using System DPI
System DPI Setting: 96 DPI (100 percent)
DWM DPI Scaling: Disabled
DxDiag Version: 6.01.7601.17514 32bit Unicode
I tried another machine, 64 bit of course, as I want to deploy my application on a 64bit PC, but still got the same problem.
This other machine was from HP, iCore 3 (4 CPUs) 2.2GHz, 4GB RAM and running Windows Professional 64 bit.
Now as I see it, it could be a Run-time environment mis-match error.
For this I tried installing a 64 bit LVRTE from NI, but still no sucess.
I checked DEP, for all 3 PCs and it was set to the following
Turn on DEP for essential Windows programs and services only (first option).
I am confused. I can not find a solution for this and it is really frustrating.

But I am assuming that when I make the installer, the 32-bit Run Time Engine is appened with the installer, as show below
Since from the picture you can see its including the support installers from '\Program Files (x86)\'
The application runs queries to fetch data from database in SQL server 2008, and for that I am using a Microsoft SQL Native Client 2008 R2 64 bit ( this is the only version that installs on either PC, even the one on which I developed my LV Application).
I am not using any driver, only toolkits for reports - and for that I un-checked the "Remove unused polymorphic VI instances" when making the executable, otherwise LV throws up an exception that share variable are not being included.
Yes I did reboot every time after I ran the installation.
Still getting the same error.

System error 988 whlie loading the LabView eun-time engine (C:\Program file\....\\lvrt.dll)

I am trying to use NI devices with Lazarus (there is no pascal section, so I post here).
When I try to run my application:
DAQmxBaseCreateTask('TaskHandle', TaskHandle);
DAQmxBaseCreateAIVoltageChan(taskHandle,'Dev1/ai0','',DAQmx_Val_Cfg_Default,-10.0,10.0,DAQmx_Val_Volts,'');
I get the following error message:
„System error 988 while loading the LabView eun-time engine (C:\Program file\....\\lvrt.dll)
nidaqmxbaselv requires a version 2010 (or compatible) LabView run-time engine. Please contact the vendor of nidaqmxbaselv to correct this problem.“
I installed LabView run-time engine 2012, but I still get the same error.
Then I tried to install LabView run-time engine 2010- the same result.
I removed LabView run-time engine 2012- same result.
I tried to install LabView run-time engine 2010 again (since I did not see it in the add/remove list)- then I noticed, that the installer shows „A newer version is already installed".
What shall I do?

Hi,
   Can I ask the same question too?
   I am using
   Windows 7 sp1 x64
   Visual Studio 2010 pro
   NI USB-6009
   ni-daqmx base 3.4.5
I created a empty win-32 console project and putted the ANSI C Example program: acquireNScans.c with the include file and lib file of nidaqmxbase in the same folder. I added this line on the top of the source code #pragma comment(lib,"nidaqmxbase.lib"), built without any error. When I tried to run it, I got this same message.
  I tried changing to shared dll mfc and delaying linking lvrt.dll, but did not work.
  Looking forward to your reply.
all the best.

PXI RT 8.6 crash with error lvrt.dll load address 0x1924000

I have an application developed with LabView RT 8.6 that run 24h/day and randomly crash evry 3-10 day with this error:
LVRT.DLL load address 0x1924000. Attached I put log file available after restarting PXI.
I dont found any information on this error, and it's very hard to found the soluction... any idea?
Attachments:
lvrt_err_log.txt ‏66 KB

Application was developed with LV 8.6, actually I have installed a LV 8.6.1 in my lap top where I develope the application. I attach some print screen of configuration of PXI.
Application running on PXI consist of several never-ending loop, one of this is a time-critical loop where I from CAN, DAQ, and I send data via CAN. There is other Hardware-timed loop that comunicate via TCP/IP with PLC and with host computer (but application on host is not developed with LV, use a client socket to comunicate with PXI for reading data).
Error Log show alwayis the same error, and for my opionon, there is no relation for when the event occur, can be in any moment.
Application in pxi has some VI that are published as web service for diagnostic only, but there is no any interaction with user, (no keyboard and no mouse), it's a silent application, that read some encoder, calculate speed and aceleration, generate some output and send all data acquired via tcp/ip... 24 h/day.
Strange is that error position is always at 0x1924000, in all the error log!
Unfortunatly system is used all the day, and it's very far from office, so debug can be done only at specific day, when production is off... and internet is unavailable...
Enabling the debug mode, It's possible to have more information about the problem without changing the performance of the system?
Thank's for you help!
Nicola
Attachments:
img1.JPG ‏36 KB
img2.JPG ‏28 KB
img3.JPG ‏29 KB

Application causes Windows fault in lvrt.dll among others...

I have an application that will occasionally crash due with a Windows error. It states that the error is in the lvrt.dll file. It lists 80 different modules in the technical information area of the warning. I have tried to reinstall all NI hardware and software and the error will still occur. it always happens at the same point in the software if it is goign to happen. This occurs right after pushing the start button the first time through the software. If I reboot the PC, the software will normally run fine for a while. Does anyone know what may be causing this problem? I have included the main application. I am running this application as an executable on the PC in question. The PC is Windows XP SP2, with a Pentium II 863 MHz and 512Mb of RAM.
Thanks,
Craig

James,
When the problem occurs, it happens at the same time, once you double click on the executable.  I was doing some testing last night, it seemed better once I reset the compact daq device in Max.  Do you think it has anything to do with the Daq device and how it sets up?  Is there a way of programatically reseting the the daq device at startup (right now daq (digital and analog) start right away once the program is executed).
I looked ath the error log file that was created and it points the ApplLib - don't know if this could help.  The system has just left to the customer for a "demo" but will be back in a few days.
Sci-Mech

Nivissvc dll error in LVRT

Hi all,
I am trying to use cRIO 9082 for image processing. When I try to deploy the vis , it shows deployed with errors. When I see the Error log it shows
LabVIEW: (Hex 0x627) The function name for the nivissvc.*:LV_AviMovieClose:C node cannot be found in the library. To correct this error, right-click the Call Library Function Node and select Configure from the shortcut menu. Then choose the correct function name.
04/09/2015 21:12:10.078 [error] LabVIEW: (Hex 0x627) The function name for the nivissvc.*:LV_AviMovieInfo:C node cannot be found in the library. To correct this error, right-click the Call Library Function Node and select Configure from the shortcut menu. Then choose the correct function name.
04/09/2015 21:12:10.098 [error] LabVIEW: (Hex 0x627) The function name for the nivissvc.*:LV_AviMovieOpen:C node cannot be found in the library. To correct this error, right-click the Call Library Function Node and select Configure from the shortcut menu. Then choose the correct function name.
04/09/2015 21:12:10.123 [error] LabVIEW: (Hex 0x627) The function name for the nivissvc.*:LV_AviMovieGetFrame2:C node cannot be found in the library. To correct this error, right-click the Call Library Function Node and select Configure from the shortcut menu. Then choose the correct function name.
04/09/2015 21:24:02.637 [error] LabVIEW: (Hex 0x627) The function name for the nivissvc.*:LV_AviMovieClose:C node cannot be found in the library. To correct this error, right-click the Call Library Function Node and select Configure from the shortcut menu. Then choose the correct function name.
What does these mean? Does this mean I cannot use AVI inside RT? or does this indicate any installation problems? It is urgent and any help is welcome

I too have been experiencing this problem, only with 8.2. I have
a built application that crashes semi-randomly on my development
machine - XP blames LVRT.DLL. I bundled the 8.2 LVRT.DLL into my
build as suggested, that didn't help. The application thus far is
just a fairly complicated GUI with no hardware being addressed (yet)
and no external libraries being called (yet).
Insight, anyone?
Thanx.

Event 1000, Application Error (Faulting application name: w3wp.exe - Faulting module name: KERNELBASE.dll)

Hello Guys,
While running a web application am getting an error like: Remote server not responding. Below are the details of event viewers which been captured at the same time when this error happened:
Event 1000, Application Error
Faulting application name: w3wp.exe, version: 7.5.7600.16385, time stamp: 0x4a5bd0eb
Faulting module name: KERNELBASE.dll, version: 6.1.7600.16850, time stamp: 0x4e211da1
Exception code: 0xe053534f
Fault offset: 0x000000000000a88d
Faulting process id: 0x%9
Faulting application start time: 0x%10
Faulting application path: %11
Faulting module path: %12
Report Id: %13
Event 1001, Windows Error Reporting
Fault bucket , type 0
Event Name: APPCRASH
Response: Not available
Cab Id: 0
Problem signature:
P1: w3wp.exe
P2: 7.5.7600.16385
P3: 4a5bd0eb
P4: KERNELBASE.dll
P5: 6.1.7600.16850
P6: 4e211da1
P7: e053534f
P8: 000000000000a88d
P9:
P10:
Attached files:
C:\Windows\Temp\WERC9CD.tmp.WERInternalMetadata.xml
C:\Windows\Temp\WERC9CE.tmp.hdmp
C:\Windows\Temp\WEREE30.tmp.mdmp
These files may be available here:
C:\ProgramData\Microsoft\Windows\WER\ReportQueue\AppCrash_w3wp.exe_30877924d6b2c607fe88a8718915f25fb79093_cab_e905f2b0
Analysis symbol:
Rechecking for solution: 0
Report Id: d46a6849-8f6a-11e1-98af-00215e6e4855
Report Status: 4
This is an priority issue which we are facing in IIS. IIS is configured for Framework 2.0 and underlying OS is - Windows
Server 2008 R2 Standard.This issue is replicable and occurring frequently Please suggest how to resolve it. Any input related to above issue is appreciable.

Please refer similar discussions and see if they help
Faulting application name: w3wp.exe
http://telligent.com/support/communityserver/community_server_2008/f/288/t/1067447.aspx
Event ID: 1000, Faulting application w3wp.exe, faulting module unknown,
http://social.msdn.microsoft.com/forums/en-US/clr/thread/9be88a2f-c8cc-4a73-9371-45ab73982123
For IIS related queries, please post them in IIS forum - http://forums.iis.net/
A UNIVERSE without WINDOWS is CHAOS !
This posting is provided "AS IS" with no warranties or guarantees and confers no rights.
About Me !!!

TS1717 On Windows Vista and tried several times to start up my iTunes, but keep getting 'application failed MSVCR80.dll error-7 (windows 126) is this an easy fix ...?

On Windows Vista and tried several times to start up my iTunes, but keep getting 'application failed MSVCR80.dll error-7 (windows 126) is this an easy fix ...?

Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99442)

Crash Application : lvrt.dll

Bonjour à tous,
Suite à quelques modifications qur mon programmer ( ajouts de listes déroulantes, de commandes personalisées et d'évènements) Et après compilation,
Mon application met entre 5 et 10 minutes à se lancer pour ensuite me mettre un message "l'application a cessé de fonctionner".
Dans la description du problème on peut voir lvrt.dll
J'ai refais un .exe de A à Z, ré-installé les Run-Time mais toujours le même problème. Auriez vous une solution ? Je dois livrer une application dans deux jours...
Merci d'avance à tous.
Résolu !
Accéder à la solution.

Bonjour...
Personne n'a d'idée sur la solution à mon problème ?
J'essaye d'enlever et remettre quelques parties de mon programme pour voir d'ou peut venir le problème mais aucun résultat jusqu'à maintenant...

Lvrt.dll error in application

Similar Messages

Maybe you are looking for