Lwapp - Command is disabled

We have some 1131 lightweight access points which were once registered with a controller which is no longer available. When we issue the command "clear lwapp private-config" The message "ERROR!!! Command is disabled."
This error message indicates that the static configuration commands are locked out because either:
This command was entered while the LAP is registered to a controller.
The LAP was previously registered to a WLC, but the username/password was not changed from the default.
OK both these things apply. The point is how do I clear the AP and start again since I cannot connect it to the controller???

Hi Ian,
What a pain (we have all been down this road and at least we won't forget to enter a username/password again :) I was working with some folks recently who were experiencing this same issue;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&topicID=.ee6e8b8&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cbf883c
Hope this helps!
Rob

Similar Messages

Outdoor Mesh 1522 - ERROR!!! Command is disabled.

I'm trying to configuring ip address static in LAP1522 but i can't.
The command clear lwapp private-config doesn't work.
clear lwapp private-config
ERROR!!! Command is disabled.
Tks

Hi Mario,
The AP needs the username/password that must be configured while the AP is connected to the WLC If no username/password was configured via the WLC this command is not available.
If the LWAPP AP did have the username and password changed while the LAP was joined to the controller then this is available via the AP's console connection
Note This command requires the controller configured Enable password to enter the CLI EXEC mode.
clear lwapp private-config
From this Troubleshooting doc;
http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html#wp1091061
setting of a Username/Password on an LWAPP AP becomes a valuable step in the configuration process;
Resetting the LWAPP Configuration on a Lightweight AP (LAP)
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00808e2d27.shtml
Deleting the LWAPP Configuration File to Redeploy the AP
When you redeploy an access point after moving it from one location to another, you must first delete the LWAPP configuration file and restore the access point to the factory default settings. Deleting the LWAPP configuration enables the commands on the access point console to configure the static IP address on the access point, the IP address on the controller, the access point hostname, and the default gateway IP address.
To delete the LWAPP configuration and restore the factory defaults, enter the following command in EXEC mode on the access point console:
clear lwapp private-config
The clear lwapp private-config command becomes available on the access point console after the controller pushes a new username and password to the access point.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp169479
Hope this helps!
Rob

ERROR!!! Command is disabled.

I have a lwapp 1130 here and it's no longer associated with the controller. I issued the clear lwapp private-config, it went through and cleared the config. Now when I try to issue the lwapp commands to set the ip and such i get ERROR!!! Command is disabled. I read that this means the static configuration is locked, but it did not say how to "unlock" it. Any ideas or suggestions on how to get this re-enabled.
This information has been added in the following Document - https://supportforums.cisco.com/docs/DOC-21897

Hi everyone, I was stuck with an AP that were on a Lab and associated to a WLC we don’t have anymore.
None of the procedures were working and we never change the enable password of the ap while it was associated, so I decide to perform the last procedure (erase de .JA2 file). Now the AP its not booting. It gets stock right here:
ap:
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 3 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 14848
flashfs[0]: Bytes available: 31854080
flashfs[0]: flashfs fsck took 13 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 00:27:0d:e4:03:6c
The system is unable to boot automatically because there
are no bootable files.
C1250 Boot Loader (C1250-BOOT-M) Version 12.4(18a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Fri 23-Jan-09 20:46 by prod_rel_team
I check an the recovery image still on the AP:
4 drwx 320 Jan 26 2010 01:58:26 +00:00 c1250-k9w8-mx.124-21a.JA2
5 drwx 128 Mar 1 2002 00:02:02 +00:00 c1250-rcvk9w8-mxp
It is a LWAPP 1250.
Any help? please.

Windows 8.1 Pro Need command to disable "Use default gateway on remote network" option on VPN connection"

Hello!
I want to create bat script to create several VPN connection.
There is powershell command to create vpn connection:
add-vpnconnection -name "Test VPN" -serveraddress "vpn.example.com" -splittunneling -tunneltype "pptp"
And I need to create VPN connection without the option "Use default gateway on remote network" option on VPN connection"
Or modify this option on existent VPN connection with command.
Please help me to find command option or other command to disable "Use default gateway on remote network" option on VPN connection" feature.

http://technet.microsoft.com/nl-nl/library/ee431701%28v=ws.10%29.aspx RouteIPv4TrafficOverRAS True – Add a default gateway on the VPN connection False – Do not add default gateway on the VPN connection

What is the Command to disable Printer Sharing via the Terminal?

What is the Command to disable Printer Sharing via the Terminal?

cupsctl is the command.
man cupsctl(8)
Hope that helps.

Some commands are disabled. How to fix it?

Photoshop Elements 11 - after opening the program few commands under 'Edit' are disabled (such as 'Copy', 'Paste', etc) are disabled or greyed out. What can I do to enable the commands?

And you do have an active selection? If so, can you post a screenshot? You'll need to come to the forum's webpage to do that. It doesn't work via email.
This discussion is at:
Some commands are disabled. How to fix it?
Then use the camera icon above the message composition area to post the image.

AP1240 LWAPP commands

We've got some new AP1240 running LWAPP. In experimenting with how they get their connection and Config to the 4400 Controller we found doco stating there are some LWAPP commands available.
Configuring Controller Information
To manually configure controller information on a new (out-of -the-box) access point using the access point CLI interface, you can use these EXEC mode CLI commands:
AP# lwapp ap ip address <IP address> <subnet mask>
AP# lwapp ip default-gateway IP-address
AP# lwapp controller ip address IP-address
AP# lwapp ap hostname name
We don't seem to find these commands available in CLI. Don't show up under help and command not found when typed in manually. Any ideas ??
Yes we know about the DHCP and DNS options we are just testing out everything.

Try this link
http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a00806a7975.html

Lwapp commands

I can set the second wireless lan controller with static command. My access are configured with lwapp command:
AP#lwapp ap controller ip address <IP-address-wlc>
but, How I can set the second ip address of my controller with lwapp comands?
thanks

Hi Ricardo,
Using the CLI, follow these steps to configure primary, secondary, and tertiary controllers for a specific access point and to configure primary and secondary backup controllers for a specific controller.
Step 1 To configure a primary controller for a specific access point, enter this command:
config ap primary-base controller_name Cisco_AP [controller_ip_address]
Note The controller_ip_address parameter in this command and the next two commands is optional. If the backup controller is outside the mobility group to which the access point is connected (the primary controller), then you need to provide the IP address of the primary, secondary, or tertiary controller, respectively. In each command, the controller_name and controller_ip_address must belong to the same primary, secondary, or tertiary controller. Otherwise, the access point cannot join the backup controller.
Step 2 To configure a secondary controller for a specific access point, enter this command:
config ap secondary-base controller_name Cisco_AP [controller_ip_address]
Step 3 To configure a tertiary controller for a specific access point, enter this command:
config ap tertiary-base controller_name Cisco_AP [controller_ip_address]
http://www.cisco.com/en/US/docs/wireless/controller/5.0/configuration/guide/c5lwap.html#wp1279106
Hope this helps!
Rob

UNIX Commands to disable Expose and Dashboard

Teacher looking to block/disable Expose and Dashboard on iMac 2.2 gHz running 10.6.1
I use ARD 3.2 and want to use a UNIX command to disable features on the students computers. If you know other Commands, maintenance scripts, permissions, etc..those would be helpful as well.
Thanks for your time and help.
David

Hi David
To disable Dashboard:
defaults write com.apple.dashboard mcx-disabled -boolean YES
You have to restart the Dock afterwards:
killall Dock
You still have to tear Dashboard off the Dock although you could amend the com.apple.dock.plist If you wanted to? Amend the persistent-apps tile data settings. To re-enable Dashboard at a future date:
defaults write com.apple.dashboard mcx-disabled -boolean NO
Restart the Dock again with the same command.
Not sure if there is a command to disable Expose? I think some of its settings can be found in com.apple.systempreferences.plist? If it looks like it has what you want you should be able copy it either using the Copy feature in ARD or sending a Unix command like cp (man cp) instead.
Alternatively apply the plist to an OD Group as a managed preference assuming you've an OD environment?
Tony

Add Voice Command Enable/Disable Bluetooth

Add Voice Command Enable/Disable Bluetooth
Do you think apple will ever add additional voice commands like one to enable and or disable Bluetooth so that I am able to save battery life and time with trying to use my Bluetooth Headset?
It’s annoying having to unlock my phone go to Home / Settings / General / Bluetooth every time I get into my car so I can use my headset.
Thanks

Hard for us to tell, since we are just users like you. You can provide feedback to Apple letting them know that you would like to see that feature. Use this link to provide feedback http://www.apple.com/feedback/iphone.html

Error Command is disabled - from lwapp CLI

Hello,
i keep getting this message when trying to restore back to default or clear controller ip definations in the lwapp ap. How do i get around this?

Hi Friend,
East way is let it join controller first and then you can reset the configuration of AP from controller GUI.
If that is not possible for you for any reason you can console into AP and issue a command "dir flash" and you will see 2 files name "env_vars" and "private" name file. Delete it from flash running a command "delete flash:env_vars" and same command to delete second file and just reload the AP and it will delete old configuration regarding controller ip address.
HTH
Ankur
*Pls rate all helpfull post

Unix command to disable DVD drive?

My DVD drive on my 20" intel imac is failing to eject the disk. It won't come out. I have done everything like restarting with the mouse held down etc etc. I am going to buy a cheap external DVD writer as a solution. The drive however is making a noise every 10 secs in what I guess is in an attempt to read the disk or eject it? What ever the noise is I want it to stop! Is there a command I can type in the terminal to kill or disable the drive so it quits trying to do what it is doing?
Thanks in advance.
Martin.

Ask at the Unix forum under OS X Technologies. BTW, this Terminal command should eject the disc:
*drutil eject -drive internal*

Is there a terminal command to disable the "Boing' sound ?

Hello, Everyone
I was wondering if any one knows if there is a terminal command that can
be used to disable the "boing" sound that folders and files make (in Tiger)
as they are being moved about the desktop and or into finder windows.
A couple of people have looked in the System preferences,usual areas but
can not locate the file for this "Boing" sound. If any one knows I would love
the answer. TIA for reading this & any help.; )
Regards , Eme
 Power PC G4 (3.3) ♥ iMac Flat Panel 10.3.9 ] 15 Alum.PowerBook Tiger Mac OS X (10.4.6) AEBS & iMac Intel Core Duo 2gb
Message was edited by: Eme~

Mine doesn't make a sound when I do this.
I presume you have unchecked the "Play user interfacesound effects" > in System Preferences> Sound. The other OP wants to disable only the infamous boing. I found both the files you wrote of. Thank you very much !
I just needed to summarize this & then undoing if so desired.
Bill, please what would the command be for undoing this action ?
Launch Terminal and type this: sudo gzip
enter ~~
password prompt,
then this : /System/Library/PrivateFrameworks/ScreenReader.framework/Versions/A/Resources/S ounds/SpringForward.aiff
Is this correct ?
Thanks so very, very much for your expertise, patience and sharing it with me.~ Eme
 Power PC G4 (3.3) ♥ iMac Flat Panel 10.3.9 ] 15 Alum.PowerBook Tiger Mac OS X (10.4.6) AEBS & iMac Intel Core Duo 2gb

Print commands are disabled in File menu (Multisim 10)

I want to print my circuit, but all Print commands in the File menu are grayed out. I do have a printer installed on my system, which works on other applications. I'm running Multisim 10 (Student Evaluation) on Windows Vista Ultimate 32-bit.
Thanks,
Ricardo Costa

The print option is disable in the evaluation version, it not your printer problem. When you activate this version, the print option will be active.
Tien P.
National Instruments

Commands are disabled

Photoshop Elements - after opening the program few commands under 'Edit' are disabled (such as 'Copy', 'Paste', etc) are disabled or greyed out. What can I do to enable the commands?

You're in the wrong forum. This is not the Elements forum.
Here's the link to the forum you want:
https://forums.adobe.com/community/photoshop_elements/content

Lwapp - Command is disabled

Similar Messages

Maybe you are looking for