Lwapp upgare problem

Good Day,
I am trying to upgrade an AP-1252 from autonomous to LWAPP. I downloaded file c1250-rcvk9w8-tar.124-10b.JA3 but the upgrade tool rejects it claiming that the image is not a valid one.
Should I be using a different file. Is there some other way to upgrade?
Thanks

Oops-- found the answer on this board.
Please pardon the laziness

Similar Messages

  • LWAPP discovery problem

    I am currently setting up a 4402 controller and lwapps. Our wireless right now is all managed by corp and is a combination of autonomous and lwapp. Here is my problem.
    I have setup option43 in my dhcp scope. When I connect a fresh radio to the same subnet as the controller I see that the radio goes to the controller but then there is a message and the radio goes to the corp controller.
    Here is the boot log from a new radio.
    %LWAPP-3-CLIENTEVENTLOG: Controller address 10.200.190.10(MINE) obtained through DHCP
    %LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
    %LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.gtna.gt.ds
    %LWAPP-3-CLIENTEVENTLOG: Controller address 10.148.198.7(CORP) obtained through DNS
    I see that message about a log server. Did I miss something?
    thanks
    tony

    Hi Guys,
    I just thought that I would link this info for the LWAPP Layer 3 startup. +5 points for both Wesley and Leo for your ongoing great work here :)
    The LWAPP AP goes through this process on startup for Layer 3 mode:
    The LAP boots and DHCPs an IP address if it was not previously assigned a static IP address.
    The LAP sends discovery requests to controllers through the various discovery algorithms and builds a controller list. Essentially, the LAP learns as many management interface addresses for the controller list as possible via:
    DHCP option 43 (good for global companies where offices and controllers are on different continents)
    DNS entry for “cisco-lwapp-controller” (good for local businesses - can also be used to find where brand new APs join)
    Management IP addresses of controllers the LAP remembers previously
    A Layer 3 broadcast on the subnet
    Over the air provisioning
    Statically configured information
    From this list, the easiest method to use for deployment is to have the LAPs on the same subnet as the management interface of the controller and allow the LAP's Layer 3 broadcast to find the controller. This method should be used for companies that have a small network and do not own a local DNS server.
    The next easiest method of deployment is to use a DNS entry with DHCP. You can have multiple entries of the same DNS name. This allows the LAP to discover multiple controllers. This method should be used by companies that have all of their controllers in a single location and own a local DNS server. Or, if the company has multiple DNS suffixes and the controllers are segregated by suffix.
    DHCP option 43 is used by large companies to localize the information via the DHCP. This method is used by large enterprises that have a single DNS suffix. For example, Cisco owns buildings in Europe, Australia, and the United States. In order to ensure that the LAPs only join controllers locally, Cisco cannot use a DNS entry and must use DHCP option 43 information to tell the LAPs what the management IP address of their local controller is.
    Finally, static configuration is used for a network that does not have a DHCP server.You can statically configure the information necessary to join a controller via the console port and the AP's CLI. For information on how to statically configure controller information using the AP CLI, refer to Manually Configuring Controller Information Using the Access Point CLI.
    For a detailed explanation on the different discovery algorithms that LAPs use to find controllers, refer to LAP Registration with WLC.
    For information on configuring DHCP option 43 on a DHCP server, refer to DHCP OPTION 43 for Lightweight Cisco Aironet Access Points Configuration Example.
    Send a discovery request to every controller on the list and wait for the controller's discovery reply which contains the system name, AP-manager IP addresses, the number of APs already attached to each AP-manager interface, and overall excess capacity for the controller.
    Look at the controller list and send a join request to a controller in this order (only if the AP received a discovery reply from it):
    Primary Controller system name (previously configured on LAP)
    Secondary Controller system name (previously configured on LAP)
    Tertiary Controller system name (previously configured on LAP)
    Master controller (if the LAP has not been previously configured with any Primary, Secondary, or Tertiary controller names. Used to always know which controller brand new LAPs join)
    ....continued on next page

  • 881w lwapp license problem

    Hi all.
    I have a little problem with a router 881w with embedded AP. This AP is working as a unified image.
    I upgrade to advipservices to support ospf and others, but now, ap is not joined to wireless lan controller.
    Checking the ap console I see this event log:
    %SM_LICENSE-6-NO_LWAPP_LICENSE:  WLAN_AP_SM: Do not have a valid Router license/config to run AP unified  image. Shutting down dot11 radio
    %SM_LICENSE-6-FLASH_FAILED:  WLAN_AP_SM: Flash failed during license operation
    %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    Do you have any idea about this issue?
    Many many thanks!!
    Albert.

    Send an email to [email protected]
    Your email should contain the following details:
    1.  Your CCO login;
    2.  The router serial number;
    3.  The error message.

  • Intel 2200BG wifi nic and aironet 1131 LWAPP's

    We recently had a nice sized installation of 1131 LWAPPS's (180) w/ WLC's and a WCS. The problem I'm having is out of the blue one day my Dell Latitude D400 w/ intell 2200BG internal wifi just disconnected and I wasn't able to reconnect. I've since formatted and rebuilt the system to ensure it's the latest n' greatest drivers (I'm running 9.0.4.13) from Dell. I checked Intel's site and they have 9.0.3.26 but nothing mentioned about the connection to LWAPP's problem. I can connect at home and other locations just fine. If I put in an external nic, I can connect to the 1131 LWAPP.
    Suggestions? Help?
    -Rob-

    Hi Rob,
    My WLC current software version is 4.0.179.8. Please tell us the stability of 4.0.206.0.
    I enabled only 802.11b and 802.11g in my LWAPP environment. The LAP model is LAP1242AG-C-K9. Antenna is AIR-ANT4941 (diversity).
    I'm using L3 LWAPP transport mode; the two WLCs (within the same Mobility/RF group) are located at a centralized data center while the LAPs are located at a remote office building. WAN is MPLS L3 VPN. WLC redundancy mode is 1+1. All LAPs join to one controller; the other acts as hot standby.
    Clients use Windows Zero Configuration (WZC). Encryption is WPA2/AES and user authentication is using Microsoft PEAP against a backend AD. ACS version 4.0.
    Clients use Dell Latitude D610 with Intel PRO 2200BG chipset. Driver version is either 9.0.4.17 or the latest 9.0.4.26. They face frequent disconnections while users with 3945ABG chipset have more stable connections.
    Please advise.
    Thank you.
    B.Rgds,
    Lim TS

  • Problem converting air-ap1131ag-a-k9 to Lwapp

    i have a person on my team who converted some autonomoous air-ap1131ag-a-k9 to lwapp. I don't think they did it right.
    what they did is , booted the ap ( at this point it was running in autonomous mode), set the ip to 192.168.1.200 and their laptop to 192.168.1.100 connected the laptop directly to the AP. (I have found out that these AP's were old AP's that previously had configs on them, ( static ips, a whole config) they came from another building , they were the ones that other lwapps replaced.)
    they then went to the web gui of the AP , went to software upgrade and loaded the lwapp recovery image on the ap (c1130-rcvk9w8-tar.124-10b.JA3.tar). the software loaded fine, and converted the AP . and thats all they did
    (I had mentioned that we should use the upgrade tool, but they didn't listen)
    the aps got mounted , on the ceiling in the hospital, but when they went to turn them on, they didnt show up right on the controller , they kept joining and unjoining..
    i think there is a problem with the SSC, i remember, something like the time had to be the same on the ap and on the WLC.
    anyways, these could be older AP's before 2005 ( unknown to me) which would mean they dont hav MIC's and have SSC. and the ap is refusing them is my thought.
    the WLC is setup to accept self signed certs.
    anyways...
    these aps are now mounted on the ceilings , and when you do a show cdp nei, it has an ip address from when it was an autonomous ap.
    Also, what is the best process you have found to convert Old autonomous 1131 AP's to lightweight mode?
    thanks
    the controller is running 4.2.176 WLC code. i currently don't have Access to WCS or a spare controller to use with the upgrade utility.
    the controller is a 4404-100

    i went to the wlc and issued the command
    debug lwapp events enable
    i got the following output
    Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 Received LWAPP JOIN REQUEST from AP 00:11:20:1a:07:a9 to 06:0a:10:10:00:00 on port '29'
    Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 AP AP0011.201a.07a9: txNonce 00:00:00:00:00:00 rxNonce 00:00:00:00:00:00
    Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 LWAPP Join Request MTU path from AP 00:11:20:1a:07:a9 is 1500, remote debug mode is 0
    Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 Processing Radius Response: AP Authorization failure for 00:11:20:1a:07:a9
    Sat Jun 13 12:41:54 2009: 00:1e:f7:ed:e8:aa Did not receive hearbeat reply from AP 00:1e:f7:ed:e8:aa
    Sat Jun 13 12:41:54 2009: DTL Deleting AP 5 - 0.0.0.0
    Sat Jun 13 12:41:55 2009: 00:11:21:89:fb:30 Received LWAPP ECHO_REQUEST from AP 00:11:21:89:fb:30
    Sat Jun 13 12:41:55 2009: 00:11:21:89:fb:30 Successful transmission of LWAPP Echo-Response to AP 00:11:21:89:fb:30
    Sat Jun 13 12:41:55 2009: 00:21:55:c2:06:20 Received LWAPP DISCOVERY REQUEST from AP 00:21:55:c2:06:20 to ff:ff:ff:ff:ff:ff on port '29'
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP STATISTICS_INFO from AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Statistics Info Response to AP 00:11:5c:03:3c:b0
    Sat Jun 13 12:41:58 2009: 00:1d:70:f4:3e:50 Received LWAPP DISCOVERY REQUEST from AP 00:1d:70:f4:3e:50 to ff:ff:ff:ff:ff:ff on port '29'
    can someone help me decipher what it means, i think i need to debug to get the sha key.
    there are about 14 new ap's. and they all have problems.
    thanks

  • Fragmentation problem with Wlan Controler 4402 due to LWAPP header overhead

    Hello there,
    I have following situation.
    network---wlan controller4402----FW1---MPLS---FW2---Access points----networks
    I can see very big amount of fragmented packets coming to FW2 and getting dropped in one moment. After those packets get dropped, access points get disconnected
    I wonder, is there any documentation, or maybe some of you guys can give me some tip/trick how to set up WLC4402 to use TCP MSS, PMTU or any other settings that can help that IP Datagrams between 4402 and access points don't go over 1300B
    Thanks a lot for any help
    Regards
    Milos

    Hello,
    Thanks for your response.
    I'm a bit confused watching this document you gave me. I don't know which part of it can be related to prevention of IP Fragments between controller and AP-s.
    Problem is that controller is located on one side of the network, and we have FW (non cisco), MPLS network, other FW and then APs
    other FW across MPLS receive a lot of fragments, which of course should be defragmented for session inspection, so this leads to large CPU utilization and fragment drops.
    If we can instruct controller to set MSS bits or to be involved in PMTU, then we could try to prevent end hosts to ever create large TCP/UDP segments/datagrams to be sent via LWAPP tunnel
    Thanks for any advice
    Cheers
    Milos

  • WLC problem - Some LWAPP APs not working

    Dear All,
    Our WLC 4402 and 46 1130AG Access points in LWAPP mode have been working flawlesly for the past few years, but suddenly this week some access points have not been working (but the rest are fine). They are correctly registered on the WLC, but if anyone tries to connect they get an authentication failrue and the WLC logs the following. Nothing on the WLC has changed, the only thing that's changed on the network is a new firewall (the WIFI network is one of the subnets) but that shouldn't affect whether users can connect to the WIFI network. Anyone have any clues as to what's going on?
    Log System Time Trap
    0
    Thu Jun 16 10:29:57 2011
    Client Deauthenticated: MACAddress:00:1f:c5:f3:84:75 Base Radio MAC:00:1d:e5:4e:95:70 Slot: 0 Reason:Unspecified  ReasonCode: 1
    1
    Thu Jun 16 10:29:14 2011
    Client Deauthenticated: MACAddress:5c:59:48:55:74:49 Base Radio MAC:00:1d:e5:4e:93:80 Slot: 0 Reason:Unspecified  ReasonCode: 1
    2
    Thu Jun 16 10:28:54 2011
    Client Deauthenticated: MACAddress:5c:59:48:55:74:49 Base Radio MAC:00:1d:e5:4e:93:80 Slot: 0 Reason:Unspecified  ReasonCode: 1
    3
    Thu Jun 16 10:20:59 2011
    Decrypt errors occurred for client 04:1e:64:33:2b:d0 using WPA key on 802.11b/g interface of AP 00:1d:e5:4d:f1:f0
    4
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:d8:9e:3f:aa:ae:18 Base Radio MAC:00:13:5f:f9:a7:10 Slot: 0 Reason:Unspecified  ReasonCode: 1
    5
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:c4:2c:03:3f:92:c0 Base Radio MAC:00:1d:e5:4d:f1:f0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    6
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:b4:07:f9:f3:87:7e Base Radio MAC:00:13:5f:fb:1b:e0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    7
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:90:27:e4:b2:da:b1 Base Radio MAC:00:1d:e5:4e:8a:50 Slot: 0 Reason:Unspecified  ReasonCode: 1
    8
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:88:c6:63:c3:47:92 Base Radio MAC:00:1d:e5:4d:f1:f0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    9
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:7c:c5:37:14:f0:bb Base Radio MAC:00:1d:e5:4e:92:d0 Slot: 0 Reason:Unspecified  ReasonCode: 1
    10
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:78:ca:39:88:c2:a3 Base Radio MAC:00:1d:e5:4e:93:10 Slot: 0 Reason:Unspecified  ReasonCode: 1
    11
    Thu Jun 16 10:20:36 2011
    Client Deauthenticated: MACAddress:5c:59:48:55:74:49 Base Radio MAC:00:1d:e5:4d:f1:f0 Slot: 0 Reason:Unspecified  ReasonCode: 1

    What kind of authentication i being used on SSID that the clients connect to? If RADIUS server is involved, can you verify if it shows any logs pointing to auth failure?
    Run a debug client on the controller for one problem client and send it over.

  • Layer 3 LWAPP problems

    large pings fail over Layer 3 LWAPP when RAP's are connected over WAN (Internet)
    also cannot browse sites etc.
    The RAP's join and clients can get IP adress from DHCP server, but cannot ping over 1399b to default gateway.
    Layer2 seems OK - 10-20ms latency
    tested on 4.0.179.11, 4.0.209, 4.1.171
    using 1242, and/or 1510's
    40-70ms Latency to Wism from AP.
    Any Ideas

    Try pinging 3 or 4 times. If it works fine then try upgrading to 802.11 g technology and also take care of number of users sharing the network.

  • Wlc 2106 problem ( cant connect to 2 lwapp ( 1242 & 1131 ) need advice

    Dear All,
    could you give me some advice to configure wlc with 2 lwapp,
    i did try to used 1 lwapp ( 1242 ag ) and it's work, but when i try to connect with 2 lwapp ( 1242 & 1131 ), i can't associated with lwapp 1131 ag, i did used same configuration for both,
    need youd advice and reference guide for this issue.
    thanks and regards

    Hi Heru,
    If both are lwapp aps then they should be able to join 2106 controller. Can you confirm if 1130 is also connected to same subnet where 1242 is connected? Is management subnet/vlan different from the vlan you are connecting your LWAPP APs.
    Hope this link should help
    http://www.cisco.com/en/US/docs/wireless/controller/4.2/configuration/guide/c42lwap.html#wp1104685
    HTH
    Ankur
    *Pls rate all helpfull post

  • Problem in standared  table  upgare 4.6c to ecc6.0

    hi guru's.
    rt now i m in upgrade project 4.6 to ecc6.0.
    i  m facing  problem please suggest  some  gud ideas.
    1) how can i come to know the standared table in 4.6c where using include  and
    append structure some changes done.
    means there is any standared progam or table where these details are stores.

    Hi
    While doing Upgrade You have to aware of all related program like BDC's , Screens related errors and all dictionary related problems.
    Some function modules may become obsolete, and some screens will change
    and some new fields will be added in the new versions etc.
    Also take care of SPAU and SPDD tcodes.
    You should be able to know about Unicode concept in sap.
    check this
    http://www.thespot4sap.com/upgrade_guide_v2.pdf#search=%22upGRADE%20STEPS%20-%20SAP%22
    also chk these 2 notes in service.sap.com
    Technical Upgrade is only a version upgrade without any functionality changes.
    The objects that are needed to be upgraded are:
    Includes
    Function Groups / Function Modules
    Programs / Reports
    OSS Notes
    SAP Repository Objects
    SAP Data Dictionary Objects
    Domains, Data Elements
    Tables, Structures and Views
    Module Pools, Sub Routine pools
    BDC Programs
    Print Programs
    SAP Scripts, Screens
    User Exits
    You can refer to the below links for more information on technical upgrade:
    https://www.sdn.sap.com/irj/sdn/wiki?path=/display/profile/2007/05/07/upgradeFROMR3TOmySAPERP-PARTII&
    https://wiki.sdn.sap.com/wiki/display/profile/UPGRADEFROMR3TOmySAPERP-PARTIII
    http://help.sap.com/saphelp_nw2004s/helpdata/en/60/d6ba7bceda11d1953a0000e82de14a/content.htm
    http://help.sap.com/saphelp_nw04/helpdata/en/2e/6d66647d9011d396b60000e82de14a/content.htm
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/5ac31178-0701-0010-469a-b4d7fa2721ca
    Regards
    Anji

  • Problems Upgrading an IOS 1231G to LWAPP

    I have two 1231G AP's that I want to upgrade to LWAPP to use in my new Airespace network, but I am having trouble getting the upgrades to work. I have used the Upgrade Tool, and it says the upgrade was successful, but when we try to connect the AP's to the controller, the AP will try to authenticate, it will fail, then reboot. It stays in this boot loop as long as it is plugged up. I have made sure the port the AP is plugged into is configured correctly, and have verified that Option 43 is configured on the scope. I can plug up a LWAPP 1242A/G to the same port and it will come up fine.
    Any one have any suggestions on why the upgraded radio will not authenticate?
    Thanks in advance...

    2 things to verify :
    - your airespace WLC is in LAYER3 mode
    - option 43 is configured for aironet access Points since it's a different configuration from airespace accesspoints (see doc for upgrade to lwapp, appendix A : configuring option 43)
    GB.

  • Problems converting 1242AP from LWAPP to Autonomous

    I tried to downgrade a 1242 LAP to Autonomous through a WLC using cisco's brief instructions:
    Step 1 Log into the CLI on the controller to which the access point is associated.
    Step 2 Enter this command:
    config ap tftp-downgrade tftp-server-ip-address filename access-point-name
    Seems easy enough, i copied the IOS file (c1240-k9w7-tar.123-7.JA5.tar) to my TFTP root. Then i ran the command mentioned above from the CLI of the WLC. The WLC takes the command but nothing happens, if i hold down mode and reboot the AP it retains its previous settings? Any ideas?

    In the end i ended up using the a version of the IOS that was one iteration older and it worked......bizzare

  • Problem with roamingin in VoIP SSID...

    Hi guys,
    My client has a WLC 5508 with a two dosens  of 1262s. I set SSID for the VoIP but when the client roams there is a  loss of packest. The client is using Cisco phones. Any help will be  appreciated.
    Pete
    (Cisco Controller) >show wlan 144
    WLAN Identifier.................................. 144
    Profile Name..................................... VoIP_Network
    Network Name (SSID).............................. Inside_144
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      Radius-NAC State............................... Disabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    Number of Active Clients......................... 10
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ 144_v
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Platinum
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... 802.11b and 802.11g only
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    Radius Servers
       Authentication................................ Global Servers
       Accounting.................................... Global Servers
          Interim Update............................. Disabled
       Dynamic Interface............................. Disabled
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Enabled
             TKIP Cipher............................. Enabled
             AES Cipher.............................. Disabled
          WPA2 (RSN IE).............................. Disabled
                                                                    Auth Key Management
             802.1x.................................. Disabled
             PSK..................................... Enabled
             CCKM.................................... Disabled
             FT(802.11r)............................. Disabled
             FT-PSK(802.11r)......................... Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-Air mode....................... Enabled
          FT Over-The-Ds mode........................ Enabled
          GTK Randomization.......................... Enabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional but inactive (WPA2 not configured)
       Tkip MIC Countermeasure Hold-down Timer....... 60
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
    Mobility Anchor List
    WLAN ID     IP Address            Status
    802.11u........................................ Disabled
      Access Network type............................ Not configured
      Network Authentication type.................... Not configured
      Internet service............................... Disabled
      HESSID......................................... 00:00:00:00:00:00
    Hotspot 2.0.................................... Disabled
      WAN Metrics configuration
        Link status.................................. 0
        Link symmetry................................ 0
        Downlink speed............................... 0
        Uplink speed................................. 0
    Mobility Services Advertisement Protocol....... Disabled
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >debug client 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Nov 30 17:02:25.463: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b2:b1:10
    *apfMsConnTask_2:  Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing  IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller  apf_policy.c:1697)
    *apfMsConnTask_2: Nov 30 17:02:25.464:  2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID  255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_2:  Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e Applying site-specific Local  Bridging override for station 2c:54:2d:ea:d4:0e - vapId 144, site  'Floor_1', interface '144_v'
    *apfMsConnTask_2: Nov 30  17:02:25.464: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy  for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface  '144_v'
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e  Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId  144, site 'Floor_1', interface '144_v'
    *apfMsConnTask_2: Nov 30  17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL  'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller  apf_policy.c:1697)
    *apfMsConnTask_2: Nov 30 17:02:25.464:  2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID  255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e Processing WPA IE type 221, length 22 for mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e apfMsRunStateDec
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e apfMs1xStateDec
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20)
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfMsConnTask_2: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Initializing policy
    *apfMsConnTask_2:  Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Change  state to AUTHCHECK (2) last state RUN (20)
    *apfMsConnTask_2:  Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 AUTHCHECK (2)  Change state to 8021X_REQD (3) last state RUN (20)
    *pemReceiveTask: Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
    *apfMsConnTask_2:  Nov 30 17:02:25.464: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) DHCP  required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
    *apfMsConnTask_2:  Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3)  Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
    *apfMsConnTask_2:  Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e apfPemAddUser2  (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP  34:bd:c8:b2:b1:10 from Associated to Associated
    *apfMsConnTask_2: Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_2:  Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e Sending Assoc Response to  station on BSSID 34:bd:c8:b2:b1:10 (status 0) ApVapId 2 Slot 0
    *apfMsConnTask_2:  Nov 30 17:02:25.465: 2c:54:2d:ea:d4:0e apfProcessAssocReq  (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP  34:bd:c8:b2:b1:10 from Associated to Associated
    *dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 0)
    *dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
    *dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
    *dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Initiating WPA PSK to mobile 2c:54:2d:ea:d4:0e
    *dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Force Auth state
    *dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Skipping EAP-Success to mobile 2c:54:2d:ea:d4:0e
    *dot1xMsgTask:  Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Starting key exchange to mobile  2c:54:2d:ea:d4:0e, data packets will be dropped
    *dot1xMsgTask: Nov 30 17:02:25.466: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                   state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START  state (message 2) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:25.990: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                         state PTKINITNEGOTIATING (message 3), replay counter  00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.015: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.015: 2c:54:2d:ea:d4:0e Received EAPOL-key in  PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e apfMs1xStateInc
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3)  Change state to L2AUTHCOMPLETE (4) last state RUN (20)
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4)  DHCP required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4)  Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e apfMsRunStateInc
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.016: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4)  Change state to RUN (20) last state RUN (20)
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5362
    *Dot1x: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Adding Fast Path rule
      type = Airespace AP Client
      on AP 34:bd:c8:b2:b1:10, slot 0, interface = 1, QOS = 2
      IPv4 ACL ID = 255, IPv6 ACL ID = 2
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path  rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  Local Bridging  Vlan = 144, Local Bridging intf id = 12
    *Dot1x_NW_MsgTask_6: Nov  30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully  plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Key exchange done, data packets  from mobile 2c:54:2d:ea:d4:0e should be forwarded shortly
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                         state PTKINITDONE (message 5 - group), replay counter  00.00.00.00.00.00.00.02
    *spamApTask5: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e Sent EAPOL-Key M5 for mobile 2c:54:2d:ea:d4:0e
    *pemReceiveTask: Nov 30 17:02:26.017: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x0
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.036: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6:  Nov 30 17:02:26.036: 2c:54:2d:ea:d4:0e Received EAPOL-key in  REKEYNEGOTIATING state (message 6) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:02:26.036: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b2:b1:10
    *apfMsConnTask_2:  Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing  IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller  apf_policy.c:1697)
    *apfMsConnTask_2: Nov 30 17:03:17.385:  2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID  255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_2:  Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e Applying site-specific Local  Bridging override for station 2c:54:2d:ea:d4:0e - vapId 144, site  'Floor_1', interface '144_v'
    *apfMsConnTask_2: Nov 30  17:03:17.385: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy  for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface  '144_v'
    *apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e  Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId  144, site 'Floor_1', interface '144_v'
    *apfMsConnTask_2: Nov 30  17:03:17.385: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL  'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller  apf_policy.c:1697)
    *apfMsConnTask_2: Nov 30 17:03:17.385:  2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID  255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_2: Nov 30 17:03:17.385: 2c:54:2d:ea:d4:0e processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e Processing WPA IE type 221, length 22 for mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfMsRunStateDec
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfMs1xStateDec
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20)
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Initializing policy
    *apfMsConnTask_2:  Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Change  state to AUTHCHECK (2) last state RUN (20)
    *apfMsConnTask_2:  Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 AUTHCHECK (2)  Change state to 8021X_REQD (3) last state RUN (20)
    *pemReceiveTask: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
    *apfMsConnTask_2:  Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) DHCP  required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
    *apfMsConnTask_2:  Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3)  Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
    *apfMsConnTask_2:  Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfPemAddUser2  (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP  34:bd:c8:b2:b1:10 from Associated to Associated
    *apfMsConnTask_2: Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_2:  Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e Sending Assoc Response to  station on BSSID 34:bd:c8:b2:b1:10 (status 0) ApVapId 2 Slot 0
    *apfMsConnTask_2:  Nov 30 17:03:17.386: 2c:54:2d:ea:d4:0e apfProcessAssocReq  (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP  34:bd:c8:b2:b1:10 from Associated to Associated
    *dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 0)
    *dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
    *dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
    *dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Initiating WPA PSK to mobile 2c:54:2d:ea:d4:0e
    *dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Force Auth state
    *dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Skipping EAP-Success to mobile 2c:54:2d:ea:d4:0e
    *dot1xMsgTask:  Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Starting key exchange to mobile  2c:54:2d:ea:d4:0e, data packets will be dropped
    *dot1xMsgTask: Nov 30 17:03:17.389: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                   state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.422: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.422: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START  state (message 2) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.422: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.423: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                         state PTKINITNEGOTIATING (message 3), replay counter  00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e Received EAPOL-key in  PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e apfMs1xStateInc
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3)  Change state to L2AUTHCOMPLETE (4) last state RUN (20)
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4)  DHCP required on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2for this client
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4)  Plumbed mobile LWAPP rule on AP 34:bd:c8:b2:b1:10 vapId 144 apVapId 2
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e apfMsRunStateInc
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.433: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4)  Change state to RUN (20) last state RUN (20)
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5362
    *Dot1x: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Adding Fast Path rule
      type = Airespace AP Client
      on AP 34:bd:c8:b2:b1:10, slot 0, interface = 1, QOS = 2
      IPv4 ACL ID = 255, IPv6 ACL ID = 2
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path  rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  Local Bridging  Vlan = 144, Local Bridging intf id = 12
    *Dot1x_NW_MsgTask_6: Nov  30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully  plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6:  Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Key exchange done, data packets  from mobile 2c:54:2d:ea:d4:0e should be forwarded shortly
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                         state PTKINITDONE (message 5 - group), replay counter  00.00.00.00.00.00.00.02
    *spamApTask5: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e Sent EAPOL-Key M5 for mobile 2c:54:2d:ea:d4:0e
    *pemReceiveTask: Nov 30 17:03:17.435: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x0
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.447: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.447: 2c:54:2d:ea:d4:0e  Received EAPOL-key in REKEYNEGOTIATING state (message 6) from mobile  2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Nov 30 17:03:17.447: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *emWeb: Nov 30 17:03:46.162:  Configuring IPv6 ACL for WLAN:144, aclName passed is NULL
    *apfReceiveTask:  Nov 30 17:03:46.173: 2c:54:2d:ea:d4:0e apfSendDisAssocMsgDebug  (apf_80211.c:2162) Changing state for mobile 2c:54:2d:ea:d4:0e on AP  34:bd:c8:b2:b1:10 from Associated to Disassociated
    *apfReceiveTask:  Nov 30 17:03:46.178: 2c:54:2d:ea:d4:0e Sent Disassociate to mobile on  AP 34:bd:c8:b2:b1:10-0 (reason 1, caller apf_ms.c:5558)
    *apfReceiveTask:  Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e Sent Deauthenticate to mobile on  BSSID 34:bd:c8:b2:b1:10 slot 0(caller apf_ms.c:5678)
    *apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMsAssoStateDec
    *apfReceiveTask:  Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMsExpireMobileStation  (apf_ms.c:5716) Changing state for mobile 2c:54:2d:ea:d4:0e on AP  34:bd:c8:b2:b1:10 from Disassociated to Idle
    *apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e pemApfDeleteMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfReceiveTask:  Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Deleted  mobile LWAPP rule on AP [34:bd:c8:b2:b1:10]
    *pemReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
    *apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMsRunStateDec
    *apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e apfMs1xStateDec
    *apfReceiveTask: Nov 30 17:03:46.183: 2c:54:2d:ea:d4:0e Deleting mobile on AP 34:bd:c8:b2:b1:10(0)

    Hi guys and Saravanan thank for the ideas....
    the qualituy is getting better, not satisfactory for the customer though...
    I have upgraded the firware as advised to 1.4.3 - I forgot to mention I have 7925g wifi phonee
    I set the 802.1x + cckm with eap-fast and WPA2 and definately the quality of the calls got a huge improvement but still not enough. What can be the reason for the confinuing problems during roaming?
    Guys, is it possible to set the CCKM without ACS (or WDS - i think that was the second option)
    here is some output:
    (Cisco Controller) show>wlan 3
    WLAN Identifier.................................. 3
    Profile Name..................................... test_wifi_144
    Network Name (SSID).............................. test144
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Disabled
    Network Admission Control
      Radius-NAC State............................... Disabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    Number of Active Clients......................... 1
    Exclusionlist.................................... Disabled
    Session Timeout.................................. 65535 seconds
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ 144_v
    --More-- or (q)uit
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Platinum
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Required
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... ap-cac-limit
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... 802.11b and 802.11g only
    DTIM period for 802.11a radio.................... 2
    DTIM period for 802.11b radio.................... 2
    Radius Servers
    --More-- or (q)uit
       Authentication................................ 172.16.106.53 1645
       Accounting.................................... Disabled
       Dynamic Interface............................. Disabled
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Enabled
             FT(802.11r)............................. Disabled
             FT-PSK(802.11r)......................... Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-Air mode....................... Enabled
          FT Over-The-Ds mode........................ Enabled
    --More-- or (q)uit
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       Tkip MIC Countermeasure Hold-down Timer....... 60
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Enabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Band Select...................................... Disabled
    Load Balancing................................... Disabled
    --More-- or (q)uit
    Multicast Buffer................................. Disabled
    Mobility Anchor List
    WLAN ID     IP Address            Status
    802.11u........................................ Disabled
      Access Network type............................ Not configured
      Network Authentication type.................... Not configured
      Internet service............................... Disabled
      HESSID......................................... 00:00:00:00:00:00
    Hotspot 2.0.................................... Disabled
      WAN Metrics configuration
        Link status.................................. 0
        Link symmetry................................ 0
        Downlink speed............................... 0
        Uplink speed................................. 0
    Mobility Services Advertisement Protocol....... Disabled
    (Cisco Controller) >debug client 2C542DEAD40E
    *apfMsConnTask_3: Dec 07 13:55:49.522: 2c:54:2d:ea:d4:0e Adding mobile on LWAPP AP 34:bd:c8:b3:d9:f0(0)
    *apfMsConnTask_3: Dec 07 13:55:49.522: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b3:d9:f0
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 0 0 0 0 0 0 0 0 0 0 0 0
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state 8021X_REQD (3)
    *apfMsConnTask_3: Dec 07 13:55:49.523: 2c:54:2d:ea:d4:0e 0.0.0.0 8021X_REQD (3) DHCP Not required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
    *apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
    *apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e apfMsAssoStateInc
    *apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e apfPemAddUser2 (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Idle to Associated
    *apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b3:d9:f0 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_3: Dec 07 13:55:49.524: 2c:54:2d:ea:d4:0e apfProcessAssocReq (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Associated to Associated
    *dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e Disable re-auth, use PMK lifetime.
    *dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e Station 2c:54:2d:ea:d4:0e setting dot1x reauth timeout = 65535
    *dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Connecting state
    *dot1xMsgTask: Dec 07 13:55:49.525: 2c:54:2d:ea:d4:0e Sending EAP-Request/Identity to mobile 2c:54:2d:ea:d4:0e (EAP Id 1)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e Received Identity Response (count=1) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e EAP State update from Connecting to Authenticating for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticating state
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.574: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=85) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 1 ===> 85 for STA 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.583: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 85)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.591: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.591: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 85, EAP Type 3)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.591: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.602: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.602: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=86) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.602: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 86)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.621: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.621: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 86, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.621: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.625: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.625: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=87) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.625: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 87)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.653: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.653: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 87, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.653: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=89) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 87 ===> 89 for STA 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.655: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 89)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.671: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.671: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 89, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.671: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.676: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.676: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=90) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.676: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 90)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.691: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.691: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 90, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.691: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.702: 2c:54:2d:ea:d4:0e Processing Access-Accept for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Username entry (test960) created for mobile, length = 253
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Username entry (test960) created in mscb for mobile, length = 253
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Setting re-auth timeout to 65535 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Station 2c:54:2d:ea:d4:0e setting dot1x reauth timeout = 65535
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 2)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Adding BSSID 34:bd:c8:b3:d9:f0 to PMKID cache at index 0 for station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: New PMKID: (16)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703:      [0000] ab 8f b5 75 ad c5 8e af 50 0d ce 4a f1 7b 16 9e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e CCKM: Create a global PMK cache entry
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Sending EAP-Success to mobile 2c:54:2d:ea:d4:0e (EAP Id 90)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703:      [0000] ab 8f b5 75 ad c5 8e af 50 0d ce 4a f1 7b 16 9e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Starting key exchange to mobile 2c:54:2d:ea:d4:0e, data packets will be dropped
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                        state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Entering Backend Auth Success state (id=90) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.703: 2c:54:2d:ea:d4:0e Received Auth Success while in Authenticating state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.704: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticated state
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START state (message 2) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e CCKM: Sending cache add
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: CCKM: Sending CCKM PMK (Version_1) information to mobility group
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: CCKM: Sending CCKM PMK (Version_2) information to mobility group
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.721: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                        state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e apfMs1xStateInc
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 L2AUTHCOMPLETE (4) DHCP Not required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5253, Adding TMP rule
    *Dot1x_NW_MsgTask_: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
      IPv4 ACL ID = 255, IPv
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  Local Bridging Vlan = 144, Local Bridging intf id = 12
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *Dot1x_NW_MsgTask_6: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *apfReceiveTask: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Dec 07 13:55:49.741: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4891, Adding TMP rule
    *apfReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
      IPv4 ACL ID = 255,
    *apfReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  Local Bridging Vlan = 144, Local Bridging intf id = 12
    *apfReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e Sent an XID frame
    *pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Dec 07 13:55:49.742: 2c:54:2d:ea:d4:0e Sent an XID frame
    *DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec03)
    *DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP selecting relay 1 - control block settings:
                            dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 0.0.0.0  VLAN: 0
    *DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP selected relay 1 - 172.16.100.121 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
    *DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Dec 07 13:55:50.513: 2c:54:2d:ea:d4:0e DHCP   xid: 0xf12d461 (252892257), secs: 0, flags: 0
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   chaddr: 2c:54:2d:ea:d4:0e
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   siaddr: 0.0.0.0,  giaddr: 10.123.200.15
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   requested ip: 10.123.205.33
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP ARPing for 10.123.200.1 (SPA 10.123.200.15, vlanId 144)
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP selecting relay 2 - control block settings:
                            dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15  VLAN: 144
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP selected relay 2 - 172.16.100.122 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   xid: 0xf12d461 (252892257), secs: 0, flags: 0
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   chaddr: 2c:54:2d:ea:d4:0e
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   siaddr: 0.0.0.0,  giaddr: 10.123.200.15
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP   requested ip: 10.123.205.33
    *DHCP Socket Task: Dec 07 13:55:50.514: 2c:54:2d:ea:d4:0e DHCP ARPing for 10.123.200.1 (SPA 10.123.200.15, vlanId 144)
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec03)
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP selecting relay 1 - control block settings:
                            dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15  VLAN: 144
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP selected relay 1 - 172.16.100.121 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP   xid: 0xf12d461 (252892257), secs: 0, flags: 0
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP   chaddr: 2c:54:2d:ea:d4:0e
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP   siaddr: 0.0.0.0,  giaddr: 10.123.200.15
    *DHCP Socket Task: Dec 07 13:55:52.512: 2c:54:2d:ea:d4:0e DHCP   requested ip: 10.123.205.33
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP sending REQUEST to 10.123.200.1 (len 374, port 1, vlan 144)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP selecting relay 2 - control block settings:
                            dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15  VLAN: 144
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP selected relay 2 - 172.16.100.122 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP DISCOVER (1)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 2
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   xid: 0xf12d461 (252892257), secs: 0, flags: 0
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   chaddr: 2c:54:2d:ea:d4:0e
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   siaddr: 0.0.0.0,  giaddr: 10.123.200.15
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   requested ip: 10.123.205.33
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP sending REQUEST to 10.123.200.1 (len 374, port 1, vlan 144)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP received op BOOTREPLY (2) (len 322,vlan 144, port 1, encap 0xec00)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP setting server from OFFER (server 172.16.100.121, yiaddr 10.123.201.4)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP sending REPLY to STA (len 430, port 1, vlan 0)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP OFFER (2)
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   xid: 0xf12d461 (252892257), secs: 0, flags: 0
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   chaddr: 2c:54:2d:ea:d4:0e
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   ciaddr: 0.0.0.0,  yiaddr: 10.123.201.4
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Socket Task: Dec 07 13:55:52.513: 2c:54:2d:ea:d4:0e DHCP   server id: 1.1.1.1  rcvd server id: 172.16.100.121
    *DHCP Socket Task: Dec 07 13:55:52.514: 2c:54:2d:ea:d4:0e DHCP received op BOOTREPLY (2) (len 322,vlan 144, port 1, encap 0xec00)
    *DHCP Socket Task: Dec 07 13:55:52.514: 2c:54:2d:ea:d4:0e DHCP dropping OFFER from 172.16.100.122 (yiaddr 10.123.205.33)
    *DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP received op BOOTREQUEST (1) (len 556,vlan 0, port 1, encap 0xec03)
    *DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP selecting relay 1 - control block settings:
                            dhcpServer: 172.16.100.121, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15  VLAN: 144
    *DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP selected relay 1 - 172.16.100.121 (local address 10.123.200.15, gateway 10.123.200.1, VLAN 144, port 1)
    *DHCP Socket Task: Dec 07 13:55:52.523: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP REQUEST (3)
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP   xid: 0xf12d461 (252892257), secs: 0, flags: 0
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP   chaddr: 2c:54:2d:ea:d4:0e
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP   siaddr: 0.0.0.0,  giaddr: 10.123.200.15
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP   requested ip: 10.123.201.4
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP   server id: 172.16.100.121  rcvd server id: 1.1.1.1
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP sending REQUEST to 10.123.200.1 (len 382, port 1, vlan 144)
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP selecting relay 2 - control block settings:
                            dhcpServer: 172.16.100.121, dhcpNetmask: 0.0.0.0,
                            dhcpGateway: 0.0.0.0, dhcpRelay: 10.123.200.15  VLAN: 144
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP selected relay 2 - NONE
    *DHCP Socket Task: Dec 07 13:55:52.524: 2c:54:2d:ea:d4:0e DHCP received op BOOTREPLY (2) (len 322,vlan 144, port 1, encap 0xec00)
    *DHCP Socket Task: Dec 07 13:55:52.525: 2c:54:2d:ea:d4:0e Static IP client associated to interface 144_v which can support client subnet.
    *DHCP Socket Task: Dec 07 13:55:52.525: 2c:54:2d:ea:d4:0e apfMsRunStateInc
    *DHCP Socket Task: Dec 07 13:55:52.525: 2c:54:2d:ea:d4:0e 10.123.201.4 DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5776
    *DHCP Soc: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
      IPv4 ACL ID = 255, IPv6 ACL ID
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  Local Bridging Vlan = 144, Local Bridging intf id = 12
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e Assigning Address 10.123.201.4 to mobile
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP success event for client. Clearing dhcp failure count for interface 144_v.
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP sending REPLY to STA (len 430, port 1, vlan 0)
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP transmitting DHCP ACK (5)
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP   xid: 0xf12d461 (252892257), secs: 0, flags: 0
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP   chaddr: 2c:54:2d:ea:d4:0e
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP   ciaddr: 0.0.0.0,  yiaddr: 10.123.201.4
    *DHCP Socket Task: Dec 07 13:55:52.526: 2c:54:2d:ea:d4:0e DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Socket Task: Dec 07 13:55:52.527: 2c:54:2d:ea:d4:0e DHCP   server id: 1.1.1.1  rcvd server id: 172.16.100.121
    *pemReceiveTask: Dec 07 13:55:52.527: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x10
    *pemReceiveTask: Dec 07 13:55:52.527: 2c:54:2d:ea:d4:0e Sending a gratuitous ARP for 10.123.201.4, VLAN Id 144
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b3:d9:f0
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Removing BSSID 34:bd:c8:b3:d9:f0 from PMKID cache of station 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:57:01.509: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfMsRunStateDec
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfMs1xStateDec
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20)
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Initializing policy
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 START (0) Change state to AUTHCHECK (2) last state RUN (20)
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 AUTHCHECK (2) Change state to 8021X_REQD (3) last state RUN (20)
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) DHCP required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfPemAddUser2 (apf_policy.c:268) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Associated to Associated
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b3:d9:f0 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_3: Dec 07 13:57:01.510: 2c:54:2d:ea:d4:0e apfProcessAssocReq (apf_80211.c:6290) Changing state for mobile 2c:54:2d:ea:d4:0e on AP 34:bd:c8:b3:d9:f0 from Associated to Associated
    *dot1xMsgTask: Dec 07 13:57:01.512: 2c:54:2d:ea:d4:0e Disable re-auth, use PMK lifetime.
    *dot1xMsgTask: Dec 07 13:57:01.512: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Connecting state
    *dot1xMsgTask: Dec 07 13:57:01.512: 2c:54:2d:ea:d4:0e Sending EAP-Request/Identity to mobile 2c:54:2d:ea:d4:0e (EAP Id 1)
    *pemReceiveTask: Dec 07 13:57:01.513: 2c:54:2d:ea:d4:0e 10.123.201.4 Removed NPU entry.
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e Received Identity Response (count=1) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e EAP State update from Connecting to Authenticating for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticating state
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.654: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=86) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 1 ===> 86 for STA 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.684: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 86)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.695: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.695: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 86, EAP Type 3)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.695: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.699: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.699: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=87) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.699: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 87)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.806: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.806: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 87, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.806: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.809: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.809: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=88) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.809: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 88)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.874: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.874: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 88, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.874: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=90) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e WARNING: updated EAP-Identifier 88 ===> 90 for STA 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.880: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 90)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.903: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.903: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 90, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.903: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.909: 2c:54:2d:ea:d4:0e Processing Access-Challenge for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.909: 2c:54:2d:ea:d4:0e Entering Backend Auth Req state (id=91) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:01.909: 2c:54:2d:ea:d4:0e Sending EAP Request from AAA to mobile 2c:54:2d:ea:d4:0e (EAP Id 91)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.061: 2c:54:2d:ea:d4:0e Received EAPOL EAPPKT from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.061: 2c:54:2d:ea:d4:0e Received EAP Response from mobile 2c:54:2d:ea:d4:0e (EAP Id 91, EAP Type 43)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.061: 2c:54:2d:ea:d4:0e Entering Backend Auth Response state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.076: 2c:54:2d:ea:d4:0e Processing Access-Accept for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.076: 2c:54:2d:ea:d4:0e Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.076: 2c:54:2d:ea:d4:0e Setting re-auth timeout to 65535 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Station 2c:54:2d:ea:d4:0e setting dot1x reauth timeout = 65535
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 2)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Adding BSSID 34:bd:c8:b3:d9:f0 to PMKID cache at index 0 for station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: New PMKID: (16)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077:      [0000] 16 bf c0 3e 07 00 79 b1 51 ca d3 47 44 69 1b a1
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e CCKM: Create a global PMK cache entry
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Sending EAP-Success to mobile 2c:54:2d:ea:d4:0e (EAP Id 91)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077:      [0000] 16 bf c0 3e 07 00 79 b1 51 ca d3 47 44 69 1b a1
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Starting key exchange to mobile 2c:54:2d:ea:d4:0e, data packets will be dropped
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                        state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Entering Backend Auth Success state (id=91) for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e Received Auth Success while in Authenticating state for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.077: 2c:54:2d:ea:d4:0e dot1x - moving mobile 2c:54:2d:ea:d4:0e into Authenticated state
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTK_START state (message 2) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e CCKM: Sending cache add
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: CCKM: Sending CCKM PMK (Version_1) information to mobility group
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: CCKM: Sending CCKM PMK (Version_2) information to mobility group
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.113: 2c:54:2d:ea:d4:0e Sending EAPOL-Key Message to mobile 2c:54:2d:ea:d4:0e
                                                                                                                        state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e Received EAPOL-Key from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 2c:54:2d:ea:d4:0e
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e apfMs1xStateInc
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state RUN (20)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) DHCP required on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1for this client
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 34:bd:c8:b3:d9:f0 vapId 3 apVapId 1
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e apfMsRunStateInc
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.164: 2c:54:2d:ea:d4:0e 10.123.201.4 L2AUTHCOMPLETE (4) Change state to RUN (20) last state RUN (20)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Reached PLUMBFASTPATH: from line 5362
    *Dot1x: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Adding Fast Path rule
      type = Airespace AP Client
      on AP 34:bd:c8:b3:d9:f0, slot 0, interface = 1, QOS = 2
      IPv4 ACL ID = 255, IPv6 ACL ID = 2
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 7006  Local Bridging Vlan = 144, Local Bridging intf id = 12
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
    *Dot1x_NW_MsgTask_6: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e Stopping retransmission timer for mobile 2c:54:2d:ea:d4:0e
    *pemReceiveTask: Dec 07 13:57:02.166: 2c:54:2d:ea:d4:0e 10.123.201.4 Added NPU entry of type 1, dtlFlags 0x0
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e CCKM: Received REASSOC REQ IE
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Reassociation received from mobile on AP 34:bd:c8:b2:b1:10
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_2: Dec 07 13:57:03.265: 2c:54:2d:ea:d4:0e processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Found an cache entry for BSSID 34:bd:c8:b3:d9:f0 in PMKID cache at index 0 of station 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Removing BSSID 34:bd:c8:b3:d9:f0 from PMKID cache of station 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: Processing REASSOC REQ IE
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: using HMAC SHA1 to compute MIC
    *apfMsConnTask_2: Dec 07 13:57:03.266: 2c:54:2d:ea:d4:0e CCKM: Received a valid REASSOC REQ IE
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e CCKM: Initializing PMK cache entry with a new PTK
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Resetting MSCB PMK Cache Entry 0 for station 2c:54:2d:ea:d4:0e
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 0
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Creating a PKC PMKID Cache entry for station 2c:54:2d:ea:d4:0e (RSN 2) on BSSID 34:bd:c8:b3:d9:f0
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Setting active key cache index 0 ---> 8
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e CCKM: using HMAC SHA1 to compute MIC
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Including CCKM Response IE (length 54) in Assoc Resp to mobile
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Sending Assoc Response to station on BSSID 34:bd:c8:b2:b1:10 (status 202) ApVapId 1 Slot 0
    *apfMsConnTask_2: Dec 07 13:57:03.267: 2c:54:2d:ea:d4:0e Scheduling deletion of Mobile Station:  (callerId: 22) in 3 seconds
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Association received from mobile on AP 34:bd:c8:b3:d9:f0
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Applying site-specific Local Bridging override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Applying Local Bridging Interface Policy for station 2c:54:2d:ea:d4:0e - vlan 144, interface id 12, interface '144_v'
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Applying site-specific override for station 2c:54:2d:ea:d4:0e - vapId 3, site 'Floor_1', interface '144_v'
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1697)
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1864)
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e STA - rates (4): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Processing RSN IE type 48, length 22 for mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e CCKM: Mobile is using CCKM
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Received RSN IE with 0 PMKIDs from mobile 2c:54:2d:ea:d4:0e
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e Setting active key cache index 8 ---> 8
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e unsetting PmkIdValidatedByAp
    *apfMsConnTask_3: Dec 07 13:57:04.925: 2c:54:2d:ea:d4:0e apfMsRunStateDec
    *apfMsConnTask_3: Dec 07 13:57:04.926: 2c:54:2d:ea:d4:0e apfMs1xStateDec
    *apfMsConnTask_3: Dec 07 13:57:04.926: 2c:54:2d:ea:d4:0e 10.123.201.4 RUN (20) Change state to START (0) last state RUN (20)

  • I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .

    HI All,
    I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
    Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
    The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
    here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
    show run-config
    Press Enter to continue...
    System Inventory
    NAME: "Chassis"   , DESCR: "Cisco 5500 Series Wireless LAN Controller"
    PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    System Information
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.235.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
    Build Type....................................... DATA + WPS
    System Name...................................... WLAN Controller 5508
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... 10.125.18.15
    Last Reset....................................... Software reset
    System Up Time................................... 41 days 5 hrs 14 mins 42 secs
    System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
    Current Boot License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... US - United States
    --More or (q)uit current module or <ctrl-z> to abort
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +20 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 10
    Number of Active Clients......................... 61
    Burned-in MAC Address............................ 30:E4:DB:1B:99:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 12
    Press Enter to continue or <ctrl-z> to abort
    AP Bundle Information
    Primary AP Image  Size
    ap3g1             5804
    ap801             5192
    ap802             5232
    c1100             3096
    c1130             4972
    c1140             4992
    c1200             3364
    c1240             4812
    c1250             5512
    c1310             3136
    c1520             6412
    c3201             4324
    c602i             3716
    Secondary AP Image      Size
    ap801             4964
    c1100             3036
    --More or (q)uit current module or <ctrl-z> to abort
    c1130             4884
    c1140             4492
    c1200             3316
    c1240             4712
    c1250             5064
    c1310             3084
    c1520             5244
    c3201             4264
    Press Enter to continue or <ctrl-z> to abort
    Switch Configuration
    802.3x Flow Control Mode......................... Disable
    FIPS prerequisite features....................... Disabled
    secret obfuscation............................... Enabled
    Strong Password Check Features:
           case-check ...........Enabled
           consecutive-check ....Enabled
           default-check .......Enabled
           username-check ......Enabled
    Press Enter to continue or <ctrl-z> to abort
    Network Information
    RF-Network Name............................. OGR
    Web Mode.................................... Disable
    Secure Web Mode............................. Enable
    Secure Web Mode Cipher-Option High.......... Disable
    Secure Web Mode Cipher-Option SSLv2......... Enable
    OCSP........................................ Disabled
    OCSP responder URL..........................
    Secure Shell (ssh).......................... Enable
    Telnet...................................... Disable
    Ethernet Multicast Forwarding............... Disable
    Ethernet Broadcast Forwarding............... Disable
    AP Multicast/Broadcast Mode................. Unicast
    IGMP snooping............................... Disabled
    IGMP timeout................................ 60 seconds
    IGMP Query Interval......................... 20 seconds
    User Idle Timeout........................... 300 seconds
    ARP Idle Timeout............................ 300 seconds
    Cisco AP Default Master..................... Enabled
    AP Join Priority............................ Disable
    Mgmt Via Wireless Interface................. Disable
    Mgmt Via Dynamic Interface.................. Disable
    --More or (q)uit current module or <ctrl-z> to abort
    Bridge MAC filter Config.................... Enable
    Bridge Security Mode........................ EAP
    Mesh Full Sector DFS........................ Enable
    AP Fallback ................................ Enable
    Web Auth Redirect Ports .................... 80
    Web Auth Proxy Redirect ................... Disable
    Fast SSID Change ........................... Enabled
    AP Discovery - NAT IP Only ................. Enabled
    IP/MAC Addr Binding Check .................. Enabled
    Press Enter to continue or <ctrl-z> to abort
    Port Summary
               STP   Admin   Physical   Physical   Link   Link
    Pr Type   Stat   Mode     Mode     Status   Status Trap    POE   SFPType  
    1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
    2 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    3 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    4 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    5 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    6 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    7 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    8 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
    Press Enter to continue or <ctrl-z> to abort
    AP Summary
    Number of APs.................................... 8
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1       US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1       US       1
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1       US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1       US       1
    Anham_AP03           2     AIR-LAP1142N-A-K9     70:81:05:88:15:b5 default location 1       US       1
    ANHAM_AP01          2     AIR-LAP1142N-A-K9     70:81:05:b0:e4:62 Small Conference 1       US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1       US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9     70:81:05:96:7a:49         Copy Room 1       US       1
    AP Tcp-Mss-Adjust Info
    AP Name             TCP State MSS Size
    KNOWLOGY_DC01       disabled   -
    KNOWLOGY_DC02       disabled   -
    --More or (q)uit current module or <ctrl-z> to abort
    KN1252_AP01         disabled   -
    KN1252_AP02         disabled   -
    Anham_AP03           disabled   -
    ANHAM_AP01           disabled   -
    ANHAM_AP04           disabled   -
    ANHAM_AP02           disabled   -
    Press Enter to continue or <ctrl-z> to abort
    AP Location
    Total Number of AP Groups........................ 3  
    Site Name........................................ ANHAM8075
    Site Description................................. ANHAM 8075 Location
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Anham_AP03           2     AIR-LAP1142N-A-K9   70:81:05:88:15:b5 default location 1     US       1
    ANHAM_AP01           2     AIR-LAP1142N-A-K9   70:81:05:b0:e4:62 Small Conference 1     US       1
    ANHAM_AP04           2     AIR-LAP1131AG-A-K9   00:1d:45:86:e1:b8   Conference room 1     US       1
    ANHAM_AP02           2     AIR-LAP1142N-A-K9   70:81:05:96:7a:49         Copy Room 1     US       1
    Site Name........................................ Knowlogy_DC
    --More or (q)uit current module or <ctrl-z> to abort
    Site Description................................. DC Center Access points
    WLAN ID         Interface         Network Admission Control         Radio Policy
    2               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KNOWLOGY_DC01       2     AIR-LAP1131AG-A-K9   00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1     US       1
    KNOWLOGY_DC02       2     AIR-LAP1131AG-A-K9   00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1     US       1
    Site Name........................................ OGR
    Site Description................................. 1934 OGR Office
    WLAN ID         Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                        None
    4               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    --More or (q)uit current module or <ctrl-z> to abort
    7               knowlogy_ogr        Disabled                         None
    9               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    KN1252_AP01         2     AIR-LAP1252AG-A-K9   00:21:d8:ef:06:50 Knowlogy Confere 1    US       1
    KN1252_AP02         2     AIR-LAP1252AG-A-K9   00:22:55:8e:2e:d4 Server Room Side 1     US       1
    Site Name........................................ default-group
    Site Description................................. <none>
    WLAN ID        Interface         Network Admission Control         Radio Policy
    1               knowlogy_ogr         Disabled                         None
    2               knowlogy_ogr         Disabled                         None
    3               knowlogy_ogr         Disabled                         None
    4               knowlogy_ogr         Disabled                         None
    5               knowlogy_ogr         Disabled                         None
    6               knowlogy_ogr         Disabled                         None
    7               knowlogy_ogr         Disabled                         None
    8               knowlogy_ogr         Disabled                          None
    --More or (q)uit current module or <ctrl-z> to abort
    9               knowlogy_ogr         Disabled                         None
    10             management           Disabled                         None
    AP Name             Slots AP Model             Ethernet MAC       Location         Port Country Priority
    Press Enter to continue or <ctrl-z> to abort
    AP Config
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch IP Address.................. 10.125.18.15
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
        Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
        Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
    --More or (q)uit current module or <ctrl-z> to abort
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 11
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
    --More or (q)uit current module or <ctrl-z> to abort
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 6
    Cisco AP Name.................................... KNOWLOGY_DC01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:1d:45:86:ed:4e
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.100
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................ wireless.knowlogy.com
    Primary Cisco Switch Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1134T0QG
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 19 m 18 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:33 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 47 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
          CFP MaxDuration ........................... 60
         BSSID ..................................... 00:1d:71:09:8f:90
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
          36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
         Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 44
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
          Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    --More or (q)uit current module or <ctrl-z> to abort
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    --More or (q)uit current module or <ctrl-z> to abort
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211b
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
        Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
           11000 Kilo Bits.......................... MANDATORY
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
    --More or (q)uit current module or <ctrl-z> to abort
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 .......................... 11 dBm
         Tx Power Level 5 .......................... 8 dBm
         Tx Power Level 6 .......................... 5 dBm
         Tx Power Level 7 .......................... 2 dBm
         Tx Power Level 8 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
    --More or (q)uit current module or <ctrl-z> to abort
         Current Tx Power Level .................... 1
       Phy DSSS parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 1
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
         Current CCA Mode .......................... 0
         ED Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
         Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 12 dB
         Coverage exception level................... 25 %
    --More or (q)uit current module or <ctrl-z> to abort
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Cisco AP Identifier.............................. 3
    Cisco AP Name.................................... KNOWLOGY_DC02
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:36:c5:c4
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.22.1.101
    Gateway IP Addr.................................. 10.22.1.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
    --More or (q)uit current module or <ctrl-z> to abort
    Cisco AP Group Name.............................. Knowlogy_DC
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.3.8.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    --More or (q)uit current module or <ctrl-z> to abort
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1131AG-A-K9
    AP Image......................................... C1130-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX1230T24F
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 22
          WLAN 2 :........................................ 21
          WLAN 4 :........................................ 25
          WLAN 3 :........................................ 25
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    --More or (q)uit current module or <ctrl-z> to abort
    AP Up Time....................................... 48 days, 20 h 24 m 41 s
    AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
    Join Date and Time............................... Tue Sep 24 21:24:35 2013
    Join Taken Time.................................. 0 days, 00 h 10 m 48 s
    Attributes for Slot 1
       Radio Type................................... RADIO_TYPE_80211a
       Radio Subband................................ RADIO_SUBBAND_ALL
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 3
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:a5:0c:30
         Operation Rate Set
           6000 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           9000 Kilo Bits........................... SUPPORTED
           12000 Kilo Bits.......................... MANDATORY
           18000 Kilo Bits.......................... SUPPORTED
           24000 Kilo Bits.......................... MANDATORY
           36000 Kilo Bits.......................... SUPPORTED
           48000 Kilo Bits.......................... SUPPORTED
           54000 Kilo Bits.......................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 36
         Number Of Channels ........................ 20
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
    --More or (q)uit current module or <ctrl-z> to abort
       Tx Power
         Num Of Supported Power Levels ............. 7
         Tx Power Level 1 .......................... 15 dBm
        Tx Power Level 2 .......................... 14 dBm
         Tx Power Level 3 .......................... 11 dBm
         Tx Power Level 4 .......................... 8 dBm
         Tx Power Level 5 .......................... 5 dBm
         Tx Power Level 6 .......................... 2 dBm
         Tx Power Level 7 .......................... -1 dBm
         Tx Power Configuration .................... AUTOMATIC
         Current Tx Power Level .................... 1
       Phy OFDM parameters
         Configuration ............................. AUTOMATIC
         Current Channel ........................... 36
         Extension Channel ......................... NONE
         Channel Width.............................. 20 Mhz
         Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
           ......................................... 104,108,112,116,132,136,140,
           ......................................... 149,153,157,161
         TI Threshold .............................. -50
         Antenna Type............................... INTERNAL_ANTENNA
         Internal Antenna Gain (in .5 dBi units).... 8
    --More or (q)uit current module or <ctrl-z> to abort
         Diversity.................................. DIVERSITY_ENABLED
       Performance Profile Parameters
          Configuration ............................. AUTOMATIC
         Interference threshold..................... 10 %
         Noise threshold............................ -70 dBm
         RF utilization threshold................... 80 %
         Data-rate threshold........................ 1000000 bps
         Client threshold........................... 12 clients
         Coverage SNR threshold..................... 16 dB
         Coverage exception level................... 25 %
         Client minimum exception level............. 3 clients
       Rogue Containment Information
       Containment Count............................ 0
       CleanAir Management Information
           CleanAir Capable......................... No
    Press Enter to continue or <ctrl-z> to abort
    Cisco AP Identifier.............................. 5
    Cisco AP Name.................................... KN1252_AP01
    Country code..................................... US - United States
    Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A
    AP Country code.................................. US - United States
    AP Regulatory Domain............................. -A
    Switch Port Number .............................. 1
    MAC Address...................................... 00:21:d8:ef:06:50
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.125.18.101
    IP NetMask....................................... 255.255.255.0
    Gateway IP Addr.................................. 10.125.18.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Enabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ Knowlogy Conference Rooms Side
    Cisco AP Group Name.............................. OGR
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    --More or (q)uit current module or <ctrl-z> to abort
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... H-Reap
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W Version .................................... 7.0.235.0
    Boot Version ................................... 12.4.10.0
    Mini IOS Version ................................ 3.0.51.0
    Stats Reporting Period .......................... 180
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Disabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. PoE/Medium Power (15.4 W)
    Number Of Slots.................................. 2
    AP Model......................................... AIR-LAP1252AG-A-K9
    AP Image......................................... C1250-K9W8-M
    IOS Version...................................... 12.4(23c)JA5
    --More or (q)uit current module or <ctrl-z> to abort
    Reset Button..................................... Enabled
    AP Serial Number................................. FTX122990L5
    AP Certificate Type.............................. Manufacture Installed
    H-REAP Vlan mode :............................... Enabled
          Native ID :..................................... 118
          WLAN 1 :........................................ 111
          WLAN 2 :........................................ 111
          WLAN 4 :........................................ 112
          WLAN 6 :........................................ 112
          WLAN 7 :........................................ 111
          WLAN 9 :........................................ 112
          WLAN 8 :........................................ 112
    H-REAP Backup Auth Radius Servers :
    Static Primary Radius Server.................... Disabled
    Static Secondary Radius Server.................. Disabled
    Group Primary Radius Server..................... Disabled
    Group Secondary Radius Server................... Disabled
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    AP Up Time....................................... 26 days, 00 h 24 m 39 s
    --More or (q)uit current module or <ctrl-z> to abort
    AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
    Join Date and Time............................... Wed Oct 9 10:59:07 2013
    Join Taken Time.................................. 0 days, 00 h 00 m 50 s
    Attributes for Slot 0
       Radio Type................................... RADIO_TYPE_80211n-2.4
       Administrative State ........................ ADMIN_ENABLED
       Operation State ............................. UP
       Radio Role .................................. ACCESS
       CellId ...................................... 0
       Station Configuration
         Configuration ............................. AUTOMATIC
         Number Of WLANs ........................... 7
         Medium Occupancy Limit .................... 100
         CFP Period ................................ 4
         CFP MaxDuration ........................... 60
         BSSID ..................................... 00:22:55:df:a5:90
         Operation Rate Set
           1000 Kilo Bits........................... MANDATORY
           2000 Kilo Bits........................... MANDATORY
           5500 Kilo Bits........................... MANDATORY
    --More or (q)uit current module or <ctrl-z> to abort
           11000 Kilo Bits.......................... MANDATORY
         MCS Set
           MCS 0.................................... SUPPORTED
           MCS 1.................................... SUPPORTED
           MCS 2.................................... SUPPORTED
           MCS 3.................................... SUPPORTED
           MCS 4.................................... SUPPORTED
           MCS 5.................................... SUPPORTED
           MCS 6.................................... SUPPORTED
           MCS 7.................................... SUPPORTED
           MCS 8.................................... SUPPORTED
            MCS 9.................................... SUPPORTED
           MCS 10................................... SUPPORTED
           MCS 11................................... SUPPORTED
           MCS 12................................... SUPPORTED
           MCS 13................................... SUPPORTED
           MCS 14................................... SUPPORTED
           MCS 15................................... SUPPORTED
         Beacon Period ............................. 100
         Fragmentation Threshold ................... 2346
         Multi Domain Capability Implemented ....... TRUE
         Multi Domain Capability Enabled ........... TRUE
         Country String ............................ US
    --More or (q)uit current module or <ctrl-z> to abort
       Multi Domain Capability
         Configuration ............................. AUTOMATIC
         First Chan Num ............................ 1
         Number Of Channels ........................ 11
       MAC Operation Parameters
         Configuration ............................. AUTOMATIC
         Fragmentation Threshold ................... 2346
         Packet Retry Limit ........................ 64
       Tx Power
         Num Of Supported Power Levels ............. 8
         Tx Power Level 1 .......................... 20 dBm
         Tx Power Level 2 .......................... 17 dBm
         Tx Power Level 3 .......................... 14 dBm
         Tx Power Level 4 ..........

    Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
    Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
    There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
    Sent from Cisco Technical Support iPhone App

  • Old famous problem - AP LAP1142N can't join the controller - 4402, please participate, let's make a good guide!

    Hello folks,
    I really feel sorry for bringing up this discussion again. I wouldn't dare to ask this question if I find someone's clear cut suggestion/solution or an overview giving a detailed step-by-step procedure. People just suggest jumping through so many  hoops like resetting the AP or converting it back to standalone mode and then back to LWAPP.
    Hence I have so many questions and hope that we can make a good guide covering all possible problems.
    1) AP was originally running a standalone image.  I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode)
    I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
    ap: set
    ?=
    DEFAULT_ROUTER=10.0.0.1
    Default_router=10.9.99.1
    ENABLE_BREAK=yes
    IP_ADDR=10.0.0.1
    IP_AddR=10.9.99.9
    MANUAL_BOOT=no
    NETMASK=255.255.255.224
    NEW_IMAGE=yes
    PWR_INJECTOR_DETECT=0016.c7fa.b394
    RELOAD_REASON=9
    ROM_PERSISTENT_UTC=1014941470
    TERMLINES=0
    netmask=255.255.255.0
    2) How would do something like "write erase" or even recover the enable password while being in AP mode? Do I really need to do it ? What I see next makes me believe there's something with the AP configuration (particularly SSH) that prevents an AP join WLC.
    3) The AP is powered on, connected to the switchport on the same L2 VLAN where WLC management interface. Then it boots and gets an IP address from the DHCP server located on the other switch.
    *Mar  1 00:00:08.695: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:08.705: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR  (0000.0000.0000)
    *Mar  1 00:00:09.629: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:17.534: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.1.122, mask 255.255.255.0, hostname AP2
    Here comes the question, why do I see this on the console (pay attention at "transport input ssh" line)? Does it have anything to do  with an error for DTLS ?
    *Apr 12 12:44:21.034: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Apr 12 12:44:31.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.141 peer_port: 5246
    *Apr 12 12:44:55.000: DTLS_CLIENT_ERROR: ../dtls/dtls_connection_db.c:1924 Max retransmission count reached!
    *Apr 12 12:44:55.000: %DTLS-3-HANDSHAKE_RETRANSMIT: Max retransmit count for 192.168.1.141 is reached.
    transport input ssh
    ^
    % Invalid input detected at '^' marker.
    4) Do I have to connect the controller ap-manager interface to the network or I can rely on the AP find the WLC via its management interface. I have never worked with 4400 series controllers. Just started with 5500 and they don't have the ap-manager interface.
    Cisco guide says: "The management interface is also used for layer two communications between the WLC and access points", so I can safely assume that it is enough. Moreover I can ping the AP from the WLC while connected to WLC via SSH and its management interface.
    5) And finally, what's wrong with the discovery? This is what I see on the controller while debugging capwap packets:
    (Cisco Controller) debug>*spamReceiveTask: Apr 12 12:53:52.253: <<<<  Start of CAPWAP Packet  >>>>
    *spamReceiveTask: Apr 12 12:53:52.253: CAPWAP Control mesg Recd from 192.168.1.122, Port 57046
    *spamReceiveTask: Apr 12 12:53:52.253:          HLEN 4,   Radio ID 0,    WBID 1
    *spamReceiveTask: Apr 12 12:53:52.253:          Msg Type   :   CAPWAP_DISCOVERY_REQUEST
    *spamReceiveTask: Apr 12 12:53:52.253:          Msg Length : 29
    *spamReceiveTask: Apr 12 12:53:52.253:          Msg SeqNum : 0
    *spamReceiveTask: Apr 12 12:53:52.253:
    *spamReceiveTask: Apr 12 12:53:52.253:   Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
    *spamReceiveTask: Apr 12 12:53:52.253:          Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
    *spamReceiveTask: Apr 12 12:53:52.253:
    *spamReceiveTask: Apr 12 12:53:52.253:   Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
    *spamReceiveTask: Apr 12 12:53:52.253:          WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
    *spamReceiveTask: Apr 12 12:53:52.253:
    *spamReceiveTask: Apr 12 12:53:52.253:   Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
    *spamReceiveTask: Apr 12 12:53:52.253:          WTP Mac Type  : SPLIT_MAC
    *spamReceiveTask: Apr 12 12:53:52.253:
    *spamReceiveTask: Apr 12 12:53:52.253:   Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
    *spamReceiveTask: Apr 12 12:53:52.253:          Vendor Identifier  : 0x00409600
    *spamReceiveTask: Apr 12 12:53:52.254:
    What discovery mode are we in? L2 or L3 ?

    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.230.0
    RTOS Version..................................... 7.0.230.0
    Bootloader Version............................... 4.0.219.0
    Emergency Image Version.......................... N/A
    Build Type....................................... DATA + WPS
    System Name...................................... Cisco_8b:83:03
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
    IP Address....................................... 192.168.1.140
    System Up Time................................... 0 days 19 hrs 9 mins 20 secs
    System Timezone Location.........................
    Configured Country............................... CA  - Canada
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +41 C
    --More-- or (q)uit
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 1
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ 00:23:5E:8B:83:00
    Crypto Accelerator 1............................. Absent
    Crypto Accelerator 2............................. Absent
    Power Supply 1................................... Absent
    Power Supply 2................................... Present, OK
    Maximum number of APs supported.................. 12
    "Show inventory" on the AP doesn't give any output. Giving you the "show version" instead omitting some legal stuff
    AP2>sh ver
    Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 12.4(18a)JA, RELEASE SOFTWARE (fc4)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Fri 21-Nov-08 01:28 by prod_rel_team
    ROM: Bootstrap program is C1140 boot loader
    BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA, RELEASE SOFTWARE (fc4)
    AP2 uptime is 1 hour, 42 minutes
    System returned to ROM by reload
    System image file is "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"
    Last reload reason:
    cisco AIR-LAP1142N-N-K9    (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID FTX1329S9NB
    PowerPC405ex CPU at 586Mhz, revision number 0x147E
    Last reset from reload
    LWAPP image version 3.0.51.0
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:22:BD:18:ED:66
    Part Number                          : 73-11451-06
    PCA Assembly Number                  : 800-30554-03
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC13282UKM
    Top Assembly Part Number             : 800-31273-01
    Top Assembly Serial Number           : FTX1329S9NB
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1142N-N-K9
    Configuration register is 0xF
    And the full boot process on WAP:
    IOS Bootloader - Starting system.
    Xmodem file system is available.
    DDR values used from system serial eeprom.
    WRDTR,CLKTR: 0x84000800, 0x40000000
    RQDC, RFDC : 0x80000038, 0x0000020a
    PCIE0: link is up.
    PCIE0: VC0 is active
    PCIE1: link is up.
    PCIE1: VC0 is active
    PCIEx: initialization done
    flashfs[0]: 149 files, 8 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 32385024
    flashfs[0]: Bytes used: 7901696
    flashfs[0]: Bytes available: 24483328
    flashfs[0]: flashfs fsck took 16 seconds.
    Reading cookie from system serial eeprom...Done
    Base Ethernet MAC address: 00:22:bd:18:ed:66
    Ethernet speed is 100 Mb - FULL duplex
    Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...#############################################################################################################################################################################################################################
    File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entry point: 0x4000
    executing...
    enet halted
    Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 12.4(18a)JA, RELEASE SOFTWARE (fc4)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Fri 21-Nov-08 01:28 by prod_rel_team
    Image text-base: 0x00004000, data-base: 0x00430000
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    flashfs[1]: 149 files, 8 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 32385024
    flashfs[1]: Bytes used: 7901696
    flashfs[1]: Bytes available: 24483328
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    Ethernet speed is 100 Mb - FULL duplex
    cisco AIR-LAP1142N-N-K9    (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID FTX1329S9NB
    PowerPC405ex CPU at 586Mhz, revision number 0x147E
    Last reset from power-on
    LWAPP image version 3.0.51.0
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:22:BD:18:ED:66
    Part Number                          : 73-11451-06
    PCA Assembly Number                  : 800-30554-03
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC13282UKM
    Top Assembly Part Number             : 800-31273-01
    Top Assembly Serial Number           : FTX1329S9NB
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1142N-N-K9
    % Please define a domain-name first.
    ip ssh version 2
    ^
    % Invalid input detected at '^' marker.
    transport input ssh
    ^
    % Invalid input detected at '^' marker.
    aaa new-model
    ^
    % Invalid input detected at '^' marker.
    aaa authentication login default local
    ^
    % Invalid input detected at '^' marker.
    login authentication default
    ^
    % Invalid input detected at '^' marker.
    transport input ssh
    ^
    % Invalid input detected at '^' marker.
    RS
    Press RETURN to get started!
    SI IDB null
    RSSI IDB null
    *Mar  1 00:00:05.992: *** CRASH_LOG = YES
    Base Ethernet MAC address: 00:22:BD:18:ED:66
    *Mar  1 00:00:06.203: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
    *Mar  1 00:00:08.251: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:08.292: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 12.4(18a)JA, RELEASE SOFTWARE (fc4)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Fri 21-Nov-08 01:28 by prod_rel_team
    *Mar  1 00:00:08.318: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:08.327: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR  (0000.0000.0000)
    *Mar  1 00:00:09.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:17.157: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.1.123, mask 255.255.255.0, hostname AP2
    logging origin-id string AP:0022.bd18.ed66
    ^
    % Invalid input detected at '^' marker.
    logging 255.255.255.255
    ^
    % Invalid input detected at '^' marker.
    logging trap 3
    ^
    % Invalid input detected at '^' marker.
    *Mar  1 00:00:27.230: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
    *Mar  1 00:00:27.343: Logging LWAPP message to 255.255.255.255.
    Translating "CISCO-LWAPP-CONTROLLER"...domain server (192.168.1.40)
    *Mar  1 00:00:38.267: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:00:39.267: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
    *Apr 12 15:39:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.141 peer_port: 5246

Maybe you are looking for