LWAPP upgrade tool and Windows 7 (64 bit)

I know this tool does not have a version for windows 7 but the company foisted the OS off on me to "Test" It works fine with windows 7 32 bit but I have windows 7 64 bit.
So, I was attempting to install and use the autonomous to LWAPP tool to upgrade an 1131 AP to LWAPP. I DL'ed version 3.4 which is the most current I could find. unfortunately, it gives me an error installing saying it could not read from the IPUT file and after installation it is convinced I already have a TFTP server running, which I do not. In addition to all that, when attempting to Uninstall the tool it says _SETUP.DLL is missing.
With that information in hand I found the _SETUP.DLL on another machine I use and copied it over which resulted in no improvements of note. I did register the dll as well. Any ideas?

I assume you are using the RTM (Release To Manufacturing) version. I would suggest, if possible, you might want to use the new XP Virtual PC feature (run XP on Windows 7), if the version of Windows 7 you are running supports it. I think the VM runs XP SP3 32-bit.
http://www.microsoft.com/windows/virtual-pc/download.aspx
You could also try changing the advance properties of the executable and indicate that it should be run in "compatability mode" of Windows XP 32-bit (I think that's an option, but my Windows 7 computer is at home)
Whatever route you take, you will receive no support from Cisco in this configuration. If you can avoid it, it might be better to not do LWAPP upgrades with Windows 7 until something official comes out.
petenugent - please be aware that Windows 7 was released to many people on August 6th. The general public release (of the exact same media) is due on October 22.
http://windowsteamblog.com/blogs/windows7/archive/2009/07/21/when-will-you-get-windows-7-rtm.aspx

Similar Messages

Action list not found error when trying to install Flash 11. I have IE8 and windows 32 bit. What can

action list not found error when trying to install Flash 11. I have IE8 and windows 32 bit. What can I do? Thanks

Hi, Please try to download the installer from the links provided in the following page: http://helpx.adobe.com/content/help/en/flash-player/kb/installation-problems-flash-player- windows.html#main-pars_header
Thanks,
Sunil

Window 8 and Windows 8.1 Upgrade Information and Windows 8 Tips

Need a tip on "how-to" do something in Windows 8 then the below links might provide the information that you need.
Microsoft Windows 8 upgrade assistant and FAQs.
HP Windows 8 Upgrade - Important Information Before You Upgrade.
HP Windows 7 to Windows 8 conversion information for Notebooks.
Test my HP PC for Windows 8 Compatibility.
Windows 8 – Tutorial Index and Windows 8 Tips
Windows 8 Apps more Windows 8 Apps
Windows 8 System Requirements
Additionally, if you Google "Windows 8 tips", you will find many excellent articles posted on the internet.
Windows 8.1 upgrade suggestions:
There are some important steps to take prior to doing the upgrade. Review this MS posted document. Be sure to run the upgrade assistant.
Be sure that Windows 8 has all of the latest MS updates installed. There are prerequisite patches that are required.
Be sure that you have at least 40 GB of hard disk free space.
Back up your data to external media.
Make a Windows 8 recovery media to external media before doing the upgrade. I prefer to use a third party hard drive imaging program.
Temporarily disable the antivirus software.
You will need to reinstall your programs after the upgrade so make note of which ones are required.
Check the HP Support site for Window 8.1 updates for your particular PC. If you don't see any updates then your PC has not been tested/certified with Windows 8.1.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

I've been running 64-bit Windows 8 Consumer Preview very nicely for several months and want to upgrade to 64-bit Windows Pro on my Pavilion a1440n. When I've tried to install from within the OS I get weird messages indicating that it can't be installed on a USB Flash drive (which I'm not trying to do). When I tried doing a clean install I got an odd message saying that certain installer files were missing and it would not complete. I called Microsoft customer support and the agent there thought my cpu would work because it wouldn't support Hyper-V, even though I understand that it optional. From running coreinfo.exe I can see that I have the PAE, NX, and SSE2 on the cpu enabled as meets requirements.
When I ran through th HP site I saw that this machine has not been tested. Is there any way of getting confirmation that Windows 8 Pro 64-bit will or won't run on my machine? The HP Product code for it is ER904AA#ABA.
Thanks!

Upgrade from 10G windows 32-bit to 11G linux 64-bit

Hi,
I am moving a 10g database on windows 32-bit environment to 11G linux 64-bit environment. I am using rman to restore the database on the new environment. The restore completes successfully after which when I open the database in upgrade mode and run utlirp.sql in order to migrate it from 32-bit to 64-bit I encounter the following error:
create or replace package STANDARD AUTHID CURRENT_USER is -- careful on this line; SED edit occurs!
/********** Types and subtypes, do not reorder **********/
type BOOLEAN is (FALSE, TRUE);
type DATE is DATE_BASE;
type NUMBER is NUMBER_BASE;
subtype FLOAT is NUMBER; -- NUMBER(126)
-- to your own code as it may in future interfere with the package
-- consistency maintenance mechanisms and could have dire results.
--#### timestamp pragma (please keep this last)
pragma TIMESTAMP('2006-04-18:00:00:00');
end;
create or replace
ERROR at line 1:
ORA-00604: error occurred at recursive SQL level 1
ORA-00942: table or view does not exist
Thanks in advance for your help.

According to
ID 757245.1 Can you Upgrade RDBMS and Convert From 32-bit to 64-bit Binaries Directly on Linux or Windows based Intel Platforms Using the Database Upgrade Assistant (DBUA)oracle does not support upgrading and changing the wordsize at the same time. A workaround is to upgrade it on the same platform and then move it to the new oS and change wordisize.
Ioan
Edited by: ioan on 15.1.2010 3:32

Upgradeing oracle 9i Windows 32 bit to Oracle 10.2.0.3 Windows 64bit

I have a DB in oracle 9.2.0.5. I have two questios
1 ) How can I upgrade this to Widnows 64 bit oracle 10.2.0.3 without doing an export import.
2) Is it possible to upgrade 9.2.0.5 straight to 10.2.0.3 Windows 64 bit without export import.
My plan is to copy the 9i DB to Windows 10.2.0.3 64 bit server , startup upgrade, then run utlip.sql and utlrp.sql.
Thank you

Just copy the datafiles and upgrade your database directly onto your target system, that'll convert automatically your db in 64-bit :
"+If you are installing 64-bit Oracle Database 10g software but were previously using a 32-bit Oracle Database installation, then the databases will automatically be converted to 64-bit during the upgrade to Oracle Database 10g except when upgrading from Release 1 (10.1) to Release 2 (10.2).+"
http://download.oracle.com/docs/cd/B19306_01/server.102/b14238/intro.htm#sthref26
Nicolas.

Autonomous - LWAPP Upgrade Tool & Vista

I tried to install the v. 3.4 upgrade tool on Vista Business 64 bit. The installation fails with a pop-up titled "Severe" with error "Error in opening iput file."
The real problem I'm having is that I can't uninstall the failed installation. It shows up in the installed programs list, but upon uninstalling pops up with "Setup Initialization Error" "Setup is unable to find _SETUP.DLL, which is needed to complete the installation. Error 103."
Any advice on how I can excise this thing out of my system?

Unfortunately that didn't do the trick. I did look at the uninstall.bat file and tried running the isuninst command manually with the same options and compatibility mode, but it just immediately exists without doing anything.

AP-to-LWAPP-Upgrade-Tool won't install

I have downloaded 3 versions, 3.0, 3.2 and 3.4.... all of them hang after extracting the files and launching setup.exe....
I have tried on several different Win XP machines... same result
Don't know if it matters at this point, but the intended WAP is an AIR-AP1252G-A-K9...
any ideas?

You can't use the tool for that:
Here is direction from a member on this forum:
It took me a while to get this information, so thought I'd share. Here it is:
You cannot use the upgrade tool to do the IOS to LWAPP for the 1250 APs.
Here is a method to do the conversion.
*Method 1 : ( Mode Button )*
1. Install an external TFTP tool such as tftpd32 tool from http://tftpd32.jounin.net/
2. Assign IP address in the range 10.0.0.2 - .254 ( Ex : 10.0.0.3) to the tftp server (your laptop or pc).
3. Download the IOS to lwapp image onto the tftp's root directory. Use http://www.cisco.com or
http://tools.cisco.com/support/downloads/go/IPCheck.x?defAdv=N&sftAdv=N&image=c1250-rcvk9w8-tar.124-10b.JA3&filepath=/swc/esd/02/crypto/3DES/281235915/guest&filename=c1250-rcvk9w8-tar.124-10b.JA3&advUrl=null&isk=Y&defInd=N&mdfid=281235915&sftType=Autonomous%20To%20Lightweight%20Mode%20Upgrade%20Image&optPlat=&relVer=12.4(10b)JA3&fileId=271159&treeMdfId=278875243&treeName=Wireless
4. Rename c1250-rcvk9w8-tar.124-10b.JA3 to c1250-rcvk9w8-tar.default
5. Make sure you set the IP address on the BVI interface of the AP if not set. Set it in the 10.0.0.x range. Default is 10.0.0.1.
6. Connect the Ethernet port on AP to your TFTP Server ( Laptop )
7. Hold the mode button and power off the AP.
8. Power back the AP while continually holding the mode button for 20-30
seconds.
*Method 2 : ( Archive Command )*
1. Install an external TFTP tool such as tftpd32 tool from http://tftpd32.jounin.net/
2. Assign IP address in the range 10.0.0.2 - .254 ( Ex : 10.0.0.3) to the tftp server (your laptop or pc).
3. Download the IOS to lwapp image onto the tftp's root directory. Use http://www.cisco.com or
http://tools.cisco.com/support/downloads/go/IPCheck.x?defAdv=N&sftAdv=N&image=c1250-rcvk9w8-tar.124-10b.JA3&filepath=/swc/esd/02/crypto/3DES/281235915/guest&filename=c1250-rcvk9w8-tar.124-10b.JA3&advUrl=null&isk=Y&defInd=N&mdfid=281235915&sftType=Autonomous%20To%20Lightweight%20Mode%20Upgrade%20Image&optPlat=&relVer=12.4(10b)JA3&fileId=271159&treeMdfId=278875243&treeName=Wireless
4. Make sure you set the IP address on the BVI interface of the AP if not set. Set it in the 10.0.0.x range. Default is 10.0.0.1.
5. Connect the Ethernet port on AP to your TFTP Server ( Laptop )
6. On AP, type archive download-sw /overwrite /force-reload tftp:///c1250-rcvk9w8-tar.124-10b.JA3
Going the other way (lwapp to autonomous)
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272
If you need to manually "prime" the LWAPP:
AP#lwapp ap ip address
AP#lwapp ap ip default-gateway
AP#lwapp ap controller ip address
AP#lwapp ap hostname
(optional)
Hope someone finds this useful!

HP Protect tools and windows 10 (HP 6930p)

Now that windows 10 is upon us... i want to ask a few simple questions. I know that HP will say that it doesnt support windows 10 for the 6930p because of yada yada yada... but windows 10 is now available for any windows 7 device and that includes the 6930p that comes with windows 7 support. So the way i see it, anyone with windows 7 should have windows 10 support. so will HP release the drivers to support windows 10. i ask this important question because i ran a seperate hard drive to test windows 10. On it, it told me to remove HP protect tools, my encryption (sounds like communism doesnt it?), and Display link. because i like HP Protect tools and the set up of my computer... i do not understand why it would force me to remove these. so after doing some searching, i noticed there are updates to protect tools but i want to ask will these updated versions support windows 10 and if so can someone post a link. Thank you

Yesterday, I gave a try by installing the same software ( compatible for 8.1 ) sp63727.exe on Windows 10. After restarting it didn't show the finger reader option while login. Today, after login using password, the Protect tools pops up and shows the finger reader setting ( setting which was in Windows 8.1 before upgrade ) taken automatically, and asked to save the config. Now I can login using finger reader successfully. I am not sure Windows 10 updated any files automatically after findin the Protect tools. Give a try reinstalling the same sp63727.exe and update this thread.

HP Protect tools and windows 10

Now that windows 10 is upon us... i want to ask a few simple questions. I know that HP will say that it doesnt support windows 10 for the 6930p because of yada yada yada... but windows 10 is now available for any windows 7 device and that includes the 6930p that comes with windows 7 support. So the way i see it, anyone with windows 7 should have windows 10 support. so will HP release the drivers to support windows 10. i ask this important question because i ran a seperate hard drive to test windows 10. On it, it told me to remove HP protect tools, my encryption (sounds like communism doesnt it?), and Display link. because i like HP Protect tools and the set up of my computer... i do not understand why it would force me to remove these. so after doing some searching, i noticed there are updates to protect tools but i want to ask will these updated versions support windows 10 and if so can someone post a link. Thank you

Solution to what, what exactly is your problem with Protect Tools and the upgrade process? No way anyone can help if you are not specific with your issues.

Quicktime and Windows 64-bit OSs

Hello,
Does anybody know how to get Quicktime to show the control bars on an web video when the OS is Windows and it is 64-bit.
I have tried in XP 64-bit, Vista 64-bit and 7 64-bit, but all I get is the first picture in the video, no controls to get it to start.
Thanks

The bars never show up in 64bit Vista with QT 7.6.4. They do show up in 7.6.6 but 7.6.6 has some play issues that have not been resolved yet.

Potoshop's tools and windows disappears with Leopard's Spaces.

Dear friends,
I was having very annoying problem with PS CS3 and spaces. Interface disappears when you focus a program that is on other space. This was with Photoshop CS3 and Flash CS3 trials. I'm very sad about this. Instead of optimizing the process its actually making it more annoying. For photoshop I used "tab" key twice to hide/show the interface, then it gets back. For flash, F4 does the same thing. But it's annoying.....
Mac Pro 2 x 2.8GHz Xeons with 2GB RAM.
I've seen a couple of guys having the same thing. Anyone found a solution?
Thanks.

I've noticed that same issue if I use the dock icons to act as application/space switchers but only on Adobe apps most notably Photoshop but occasionally Illustrator too it seems. I've adopted a different solution which seems to solve that options bar/tool box disappeaing act. In System Preferences/Exposé there is an option to use hot corners. I've assigned Spaces to my lower right corner. Flicking my cursor to that corner gives me a graphic image of all my spaces and windows open in each. In that image I can select my Photoshop space and don't experience the interface disappearing issue.

SAPBobsCOM.dll and windows 64 bits

When i try to connect to sap using di api, i have a exception:
Retrieving the COM class factory for component with CLSID {632F4591-AA62-4219-8FB6-22BCF5F62007} failed due to the following error: 80040154
I have a web service on windows 64 bits and I have reinstalled di api

Hello
When you compile your application, you must use x86 type as target CPU. reason: B1 and SDK components are running in 32 bit mode under x64 machines. x64 application cannot communicate x86 applications in .COM components. Your addon is compiled to x64, and the DI API is x86 compiled.
This is the reason why you receice error message,
Also nice, if you give the directirve Win32 = True to the compiler when you build you appliaction.
Regards
János

Experiences with 10.1.8.3. and Windows 32 bit

Hi all,
we successfully installed 10.1.8.3. on Windows 2003 Server 32 bit. After the installation the crawling jobs works fine. But invoking https:\\<OSES_HOME>search/query/search and searching a keyword we get PLS-00306: wrong number or types of arguments in call to 'GETRESULT'.
Does anybody else receive the same problem ?
regards Rainer

hello RaiFri..
Did you get an answer for this question? Were you able to solve the error?
We have an instance where we are getting this error but we are running on Solaris 10 64-bit version but the SES version is same (10.1.8.3.0).
Getting this error after the upgrade from 10.1.8.2.
Thank you,
Taj

Cannot upgrade an AP to LWAP using the upgrade tool on Windows 7

Hello,
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success. Help!
Thanks,
Kristen Woodard
Network Engineer II

As an aside here, if the AP are newer, manufactured after 6/2005(Has a MIC and not a SSC), you can do a normal archive download command to run the upgrade to the recovery image. Can even be scripted to run multiple times via shell/cron
HTH,
Steve
Please remember to rate helpful posts or to mark the quesiton as answered so that it can be found later.

Lightroom 6 and windows 32 bit

Hi,
I just wanted to start with the next level of photo shooting/editing.
Thus I purchsed Lightroom 6 and when I installed it, a error message came up ...
it needs obviously a 64bit computer.
What can I do now?!?!
I the only chance to buy a new desktop?!?!
Thx,

I also bought the download LR version 6 as an update of LR version 5.7 and tried to install it with the same error message of a 64bit windows version.
But this is not mentioned in the "Systemanforderung". They write following for:
Windows
- Intel®- oder AMD-Prozessor mit 64-Bit-Unterstützung*
- Windows 7 mit Service Pack 1, Windows 8 oder Windows 8.1
* Doppelkern-Prozessor für HD- oder AVCHD-Funktionen empfohlen
The same is mentioned for LR version 5
There isn`t given any directive to use a 64bit Win 7 version, only the recommendation for the processor *...
Does it really mean for LR6 is a 64bit WIN version necesary?
If yes, what can I do to reject version LR6 and get my money back?
Thx

LWAPP upgrade tool and Windows 7 (64 bit)

Similar Messages

Maybe you are looking for