LWAPP won't joint controller. Possible US/Mexico Issue
I have some LWAPPs in Mexico that will not join a controller set to MX country code until I first join them to a US controller, let it update the firmware, then join them to the MX controller. Is this normal? It seems very inefficient to do it this way. Any help would be appreciated. Thanks, Dan . . .
Hi Dan,
No, this doesn't sound normal at all. I have not worked with AP's in different countries (Canada only :) but it sounds like you have some sort of mix and match between Country codes on the AP's vs WLC. Maybe you could look into what Country Code is set on each WLC. In WLC 4.1.171.1 and later you can set the controller for Multiple Country Codes. Maybe this would help;
Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 4.1.171.0
Multiple country code support-This release allows you to configure up to 20 country codes per controller. This multiple-country support enables you to manage access points in various countries from a single controller. This feature is not supported for use with Cisco Aironet mesh access points.
-A (U.S., Canada, and Philippines), -N (Mexico, Australia, Hong Kong, India, and New Zealand),
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/c41170rn.html#wp257406
Hope this helps!
Rob
Similar Messages
-
2014 April 29, Firefox works fine but April 30 it won't start, the possible to work is running compatibility (troubleshoot). Is there any solution for this without running compatibility or without formatting computer? And works during 2014 April 29.
I've already uninstall anti virus
I try also restore and repair windows
I've also uninstall and reinstall firefox.
still doesn't work :(If you had an update of Firefox, the firewall may be the problem.<BR><BR>
This problem occurs when your Internet security program was set to trust the
previous version of Firefox, but no longer recognizes your updated version as
trusted. Now how to fix the problem: To allow Firefox to connect to the Internet
again:<BR><BR>
* Make sure your Internet security software is up-to-date (i.e. you are running the latest version)<BR><BR>
* Remove Firefox from your program's list of trusted or recognized programs, then add it back. For detailed instructions, see Configure firewalls so that Firefox can access the Internet. -
Analysis could not be performed in time. There is a possible serious performance issue
Can someone please advise what I need to do to correct this critical error?
My computer is VERY slow and when I ran the event viewer, this is listed as CRITICAL. Any information would be appreciated.
Log Name: Microsoft-Windows-Diagnostics-Performance/Operational
Source: Microsoft-Windows-Diagnostics-Performance
Date: 6/24/2010 10:18:46 AM
Event ID: 400
Task Category: System Performance Monitoring
Level: Critical
Keywords: Event Log
User: LOCAL SERVICE
Computer: user-PC
Description:
Information about the system performance monitoring event:
Scenario : System Responsiveness
Analysis result : Analysis could not be performed in time. There is a possible serious performance issue
Incident Time (UTC) : 6/24/2010 5:17:07 PM
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Diagnostics-Performance" Guid="{cfc18ec0-96b1-4eba-961b-622caee05b0a}" />
<EventID>400</EventID>
<Version>1</Version>
<Level>1</Level>
<Task>4005</Task>
<Opcode>37</Opcode>
<Keywords>0x8000000000010000</Keywords>
<TimeCreated SystemTime="2010-06-24T17:18:46.941Z" />
<EventRecordID>5491</EventRecordID>
<Correlation ActivityID="{00000000-E6C8-0000-F4BB-058D9113CB01}" />
<Execution ProcessID="1884" ThreadID="5956" />
<Channel>Microsoft-Windows-Diagnostics-Performance/Operational</Channel>
<Computer>user-PC</Computer>
<Security UserID="S-1-5-19" />
</System>
<EventData>
<Data Name="ShellScenarioStartTime">2010-06-24T17:17:07.442Z</Data>
<Data Name="ShellScenarioEndTime">2010-06-24T17:17:12.442Z</Data>
<Data Name="ShellSubScenario">1</Data>
<Data Name="ShellScenarioDuration">5000</Data>
<Data Name="ShellRootCauseBits">0</Data>
<Data Name="ShellAnalysisResult">2</Data>
<Data Name="ShellDegradationType">1</Data>
<Data Name="ShellTsVersion">1</Data>
<Data Name="ShellMachineUpTimeHours">0</Data>
<Data Name="ShellMachineSleepPattern">0</Data>
</EventData>
</Event>I do get the same problem. It believe it started after I switched from HDD to SSD some month's ago. My machine is very fast now so I do not have performance problems (only a very slow power on boot).
The description above is exactly the same as I have.
Does somebody has the same problems? -
Cisco AP1142N won't join controller
Hi
When upgrading one of our WISM controller cards a problem occurred with some AP1142N.
The can’t join controller with 7.6.120.0, upgrading was from 7.4.121.0
When CLI into the AP I got this messages:
Reboot and tries to connect to the WISM2 with 7.6.120.0, but it fails.
Then tries to connect to another WISM2 with 7.4.121.0 and this work
But then the image on the AP is not correct (have a 7.6.120.0 image)
Downgrading AP to 7.4.121.0 image
Reboot and are back to number 1.
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I '(index 0).
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:29.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
Translating "CISCO-CAPWAP-CONTROLLER.net.yyyy.se"...domain server (xxx.xxx.xxx.xxx) [OK]
*Mar 1 00:00:59.550: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I '(index 0).
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:29.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Sep 10 11:25:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.17.16.25:5246
*Sep 10 11:26:00.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I (index 0).
*Sep 10 11:26:00.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:30.000: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
examining image...
extracting info (292 bytes)
Image info:
Version Suffix: k9w8-.124-23c.JA8
Image Name: c1140-k9w8-mx.124-23c.JA8
Version Directory: c1140-k9w8-mx.124-23c.JA8
Ios Image Size: 4915712
Total Image Size: 5110272
Image Feature: WIRELESS LAN|LWAPP
Image Family: C1140
Wireless Switch Management Version: 7.0.250.0
Extracting files...
c1140-k9w8-mx.124-23c.JA8/ (directory) 0 (bytes)
extracting c1140-k9w8-mx.124-23c.JA8/T5.bin (23836 bytes)
*Sep 10 11
extracting c1140-k9w8-mx.124-23c.JA8/8001.img (174932 bytes):25:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.17.16.25:5246With a WISM, you have by definition an etherchannel between your controller & APs. Try setting the load balancing algorithm on the switch housing the WISM to src-dst-mac before connecting the AP. There is/was an issue that shows itself rarely where other load balancing mechanisms interfere with an AP's initial join to a controller. The problem declined significantly over the years, but you may be running into it.
Once the AP joins, you can reset your load balancing and you shouldn't have the problem even if the AP reboots later. It usually impacts APs that have never joined your controller. Don't know why. Since this was an upgrade it may not be your problem, but it won't hurt to try. -
ITunes 8.2 won't start? Possible solution
After a bunch of software updates downloaded to my wife's iBook (G4, 14", 1.33 GHz, 768 MB RAM, OS X 10.4.11) last week, iTunes wouldn't start.
I tried other discussion suggestions (temporarily removing .itdb files in the [username]/Music/iTunes folder and deleting the folder's iTunes Library). iTunes still wouldn't start.
I trashed iTunes and followed other suggestions to remove all traces of it. I emptied the trash, restarted and reinstalled: Did iTunes work? Nope.
The crash report mentioned Quicktime. I tried to start it. No go. Hmmmm.
So I trashed Quicktime.app and all traces of it in /Library, /Library/Preferences and ~/Library (get to those by choosing Finder/Go/Go to Folder . . .)
I noticed the Quicktime folder for Library/Preferences also contained files for Flip for Mac WMV. So I deleted the Flip for Mac application, too. I emptied the trash. Two items wouldn't delete: an apple service -- can't remember what -- and a Flip for Mac service. The Mac said they were in use. So I emptied the trash again after the restart to delete those things.
Then I reinstalled Quicktime (7.6.2 for Tiger).
Viola. iTunes (and Quicktime) started working.
I suspect Flip for Mac and its parts were the culprits. I can't prove it. It was an older install and possibly incompatible with the latest update.
At the very least, removing Quicktime and reinstalling it solved my problem.same boat...8.2 won;t install.
Trouble shooting advises to uninstall itunes and QTime and download, can't download, machine locks up everytime at 97% complete. Now I can;t acces itunes at all...
And of course no support from Apple. Can't find anyone to answer an email or get a number to call...//
Anybody?
If you get something please respond and I will do the same... -
Decommissioning a domain controller - Possible Scenarios
Hello,
I am in the process of upgrading my window server 2003 to 2012 R2.
I have introduced a swing DC,installed 2012 on it,ensured that replication is occuring between the two and succesffully transfered the roles from the old DC to the new temporary 2012 DC.
Refer to this thread for the procedures in use
http://social.technet.microsoft.com/Forums/en-US/1c742612-ff44-4521-bb68-53b17b287fae/upgrade-domain-controller-from-windows-server-2003-sp2-to-windows-server-2008-or-2012?forum=winservergen
Now i intend to decommission the old 2003 server , and to a fresh reinstallation of 2012 in it,then once i ensure replication has occured, transfer back the roles and decommission the swing DC
Both server are global catalogs..
My question is this, Do i just do a fresh reinstallation of the 2012 on the old server 2003 without first demoting it? or do i demote it ,test and then install 2012 on it...
Since the servers are GC both,is there a possibility that when i demote the old DC the DNS,AD details that had replicated dissapears?
What any other cautions should i check?
ThanksHello,
demotion is ALWAYS required except you do in-place upgrades which is not recommended on DCs.
If you don't do a correct demotion, also removing it from AD UC after removing the server complete from the network, checking DNS zones and zone properties and Name server tabs and removing the DC from AD sites and services (not done during demotion),
you may run into trouble when installing a new DC with the same name and also have always replication errors as the AD database doesn't know that the DC is removed correct.
With a not correct demoted DC AD metadata cleanup is required.
BEFORE demoting the old OS machine ASSURE that the enw DC has also the NETLOGON and SYSVOL share available and they contain the same content as on the old DC.
Also the new DC MUST become DNS server if you don't have any domain member server that handles DNS zones.
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://msmvps.com/blogs/mweber/
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights. -
Originating more than 1 EoIP tunnel to an anchor controller possible?
I'm attempting to set up (for testing purposes) a 2nd 'guest' SSID on an internal WLC (WLC-A), and terminate it in a DMZ on an anchor controller (WLC-B). We already have a guest SSID originating on WLC-A and terminating on WLC-B though. Is it possible to originate a 2nd guest SSID on WLC-A?
WLC-A - 2504 (7.2.x)
WLC-B - 5508 (7.2.x)
The problem I'm seeing is I'm getting no DHCP address assigned on the test SSID. If I statically assign IP information I still have no connectivity. It's as if the EoIP tunnel for the 2nd test SSID isn't functional.
TIAAlso when you do this, makes sure you have the same SSID configuration on both WLCs. If you created a new test SSID on the foreign, you need to create a new test SSID in the anchor. The only difference in the configuration should be the interface. Also make sure the test SSID in the anchor is anchored to itself (local) and the test SSID in the foreign WLC is anchored to the anchor WLC. The test SSID in the anchor can share the same interface as the guest.
Sent from Cisco Technical Support iPhone App -
Just unboxed my first new 3700 AP. Fired it up and it doesn't appar to like my controller. Anyone have any suggestions?
IOS Bootloader - Starting system.
flash is writable
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 12 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 7354880
flashfs[0]: Bytes available: 33803776
flashfs[0]: flashfs fsck took 10 seconds.
Base Ethernet MAC address: 3c:08:f6:6c:f5:04
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...##########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 12 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 7354880
flashfs[0]: Bytes available: 33803776
flashfs[0]: flashfs fsck took 10 seconds.
Base Ethernet MAC address: 3c:08:f6:6c:f5:04
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx;flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...######################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Sat 16-Nov-13 10:46 by prod_rel_team
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 12 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 7354880
flashfs[2]: Bytes available: 33545728
flashfs[2]: flashfs fsck took 10 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete.
Copying radio files from flash: to ram:
%Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/R2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Q2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/C2.bin (No such file or directory)
Uncompressing radio files...
File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/R5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Q5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/C5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/8006.img
...done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3702I-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FTX175071RZ
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.1.118
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 3C:08:F6:6C:F5:04
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17482H3B
Top Assembly Part Number : 068-05054-01
Top Assembly Serial Number : FTX175071RZ
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-A-K9
% Please define a domain-name first.
Press RETURN to get started!
APAVC: Initial WLAN Buffers Given to System is 2500
APAVC: WlanPAKs 18174 RadioPaks 17566
set_radio_pwr_mode: bad radio unit# 0
set_radio_pwr_mode: bad radio unit# 1
*Mar 1 00:00:13.663: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:15.707: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:16.067: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Sat 16-Nov-13 10:46 by prod_rel_team
*Mar 1 00:00:16.107: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:16.107: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default configlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:16.231: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:17.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to upERROR: Failed to configure ethernet promiscuous mode. Interface Descriptor mismatch
*Mar 1 00:00:20.919: DPAA Initialization Complete
*Mar 1 00:00:20.919: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:21.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:34.859: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:53.751: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.13.1.85, mask 255.255.254.0, hostname AP3c08.f66c.f504
Translating "CISCO-CAPWAP-CONTROLLER.childrenshc.org"...domain server (10.12.18.255)
*Mar 1 00:01:03.731: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.11.0.210 obtained through DHCP
*Mar 1 00:01:03.731: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.11.0.212 obtained through DHCP
*Mar 1 00:01:03.731: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:03.731: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.childrenshc.org
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'c5508-2.cpt'running version 7.5.102.0 is rejected.
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:03.735: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.11.0.212
*Mar 1 00:01:13.735: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'c5508-2.cpt'running version 7.5.102.0 is rejected.
*Mar 1 00:01:13.735: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.Just confirmed with the Cisco guys, thats a mistake. 7.6 code is needed, 7.5 not supported with 3700.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
LWAPP cannot join WLC2504 controller
Hello.
I have WLC5204 controller and AIR-CAP1602 access points.
I have the latest software version on the wlc.
I connect the wlc to a trunk port. i have internal dhcp server enabled in wlc.
when i connect the ap to access port same vlan as management interface vlan, the ap cannot join the controller.
the ap is assigned an ip address from the dhcp server but the following error logs are displayed:
did not get log server setting from dhcp
invalid event 10 and state 5 combination
failed to process message type 10 state 5
failed to handle capwap control message form controller
failed to process encrypted capwap packet from 192.168.1.10
I would really appreciate your help in this matter.
Regards.1. WLC sh sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... GDNE test
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 20.20.20.10
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 38 mins 46 secs
System Timezone Location......................... (GMT +2:00) Jerusalem
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +27 C
External Temperature............................. +31 C
Fan Status....................................... 3700 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 1C:DE:A7:06:A5:40
Maximum number of APs supported.................. 10
2. WLC sh time
Time............................................. Thu Dec 4 13:26:30 2014
Timezone delta................................... 0:0
Timezone location................................ (GMT +2:00) Jerusalem
NTP Servers
NTP Polling Interval......................... 86400
Index NTP Key Index NTP Server NTP Msg Auth Status
1 0 AUTH DISABLED
3. AP show version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:56 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP7c0e.ce85.5e74 uptime is 1 minute
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-4.JB6/ap1g2-k9w8-mx.152-4.JB6"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 229366K/32768K bytes of memory.
Processor board ID FGL1833X71G
PowerPC CPU at 533MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 7C:0E:CE:85:5E:74
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC1832800C
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1833X71G
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xF
4. AP show ip interface brief
Interface IP-Address OK? Method Status Protocol
BVI1 20.20.20.101 YES DHCP up up
Dot11Radio0 unassigned NO unset up up
Dot11Radio1 unassigned NO unset up up
GigabitEthernet0 unassigned NO unset up up
GigabitEthernet0.1 unassigned YES unset up up -
Trouble getting 1130AG LWAPP to Connect to Controller
I'm having trouble getting any of my 1130AG LWAPPs to connect to my WLC.
I have not configured my DHCP server to deliver option 43 or option 60.
However, I have manually configured the LWAPP using the CLI. I have assigned a static IP address, the default-gateway, gave it a hostname, and gave it the controller ip address.
When I issue the command:
show lwapp ip config
all of the information appears correctly.
However, the controller never registers the LWAPP.
This is a completely new setup, so there are no previous configs to contend with.
If I issue the command on the LWAPP:
debug lwapp client event
Two debug messages appear consistently every 3-5 seconds. They are:
*Mar 1 00:34:26.733: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 1 00:34:36.733: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR
Any suggestions?
~ Vance R. GregoryYou have to put option 43 in hexadecimal no. below you will find an example of DHCP configurations on router that act as a DHCP for LWAPP in different network:
ip dhcp excluded-address 172.16.1.1 192.168.1.1
ip dhcp pool WAP_DHCP_SCOPE
network 192.168.1.0 255.255.255.0
option 43 hex f104c0a814f0
The hex string is assembled by concatenating the TLV values shown below:
Type + Length + Value
Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex.
WLC IP is 192.168.20.240 f1+1*4+ac10.14f0 = f104c0a814f0
default-router 192.168.1.1 -
Windows 7 won't load properly / possible HDD failure?
Well I will start off by saying I've been having problems with this since I've bought it. It used to be under warranty and I had to ship it back twice, and I've had to do countless system recoveries but this time I'm at a loss. My current problem started about 4 days ago. I had skype downloaded, and my skype started freezing randomly, but only for 30 seconds to a minute, and then come right back to working. Then this started happening more frequently, and then it got to the point to where it wasn't just skype that would freeze, it was my computer. It must have only been explorer.exe that was freezing or something because my mouse still moved, and if I was in a skype call the skype call would work but I couldnt type or click on skype without it saying that it wasn't responding. Then yesterday that problem upgraded again to nothing working very well. My computer (again I can only assume it was explorer or something) would start up normally, and then once I got to my desktop the load light would come on my tower and freeze / slow down anything and everything. Example was I had VLC media player open watching a show and the video would freeze for 2 to 5 minutes, play for 10 seconds, then freeze again. Beforehand it was only slight lock ups, but then it became full blown lockups. Once that load light came on it stayed on and never wavered and I would be forced to restart my computer to even give it a chance to run properly for a few minutes before this same problem would occur. Yesterday however the problem upgraded once again, and my computer wouldn't even let me get to my desktop normally. I was able to load into safemode with networking to try some solutions but nothing worked. Then the hangup issue started occuring in safe mode as well, forcing me to restart again. This is where it just keeps getting worse sadly. My computer would get to the "Starting Windows" screen, sit there for a couple minutes, then maybe 1 out of 10 attempts it would get to the "Welcome" screen as if it was trying to load my desktop but never would load it, and on the other 9 attempts I didn't make it to the "Welcome" screen it just sat a black screen with the load light going and it would never do anything. My mouse has never been frozen at any point so it's not a full on freeze situation, but something isn't right. I did a sytem recovery last night, put it back once again to factory settings and it still locked up a little but nothing compared to how it had been. I turned my pc off and went to sleep, and then this morning it did the usual not getting past the "starting windows" screen. Sometimes it wouldn't even recognize my hard drive, giving me the old "insert media and boot from disc" or "No media found", I also got two errors, PXE-E61: Media test failure, check cable, and the other message was PXE-MOF: Exiting PXE ROM. Then after receiving those messages my computer would restart and give me the choice to hit a button to load from disk. Throught the course of this problem I tried startup repairs, smart tests, anti viruses, nothing did anything to help. So I decided once again it was going to be time for a system recovery, but now when I hit f11 to go into the system recovery options, all of it is blacked out. I can't even click on system recovery anymore. So at this point Windows 7 won't load at all, not even in safe mode, and I'm lucky to even be given the OPTION to start it in safe mode. Half of the time it seems my computer doesnt even recognize my harddrive, and I can't even do a system recovery or repair tools, but the repair tools didn't really do anything anyway. So I have no way to use that computer, and Im thinking it might be HDD failure but I'm not hearing any noises coming from it and my computer has always been a little slow so it's not like things have slowed down by a lot so I'm not so sure its my HDD but I have no idea what to do or where to start since I've exhausted all my of resources on trying to fix this issue myself. I know this problem is probably way too vague to try to get an accurate idea of what is wrong, but I will check back now and then and answer any questions to the best of my ability (I'm not tech savy so if you need really fancy PC information you wil most likely need to tell me how to acquire said information). I mean I guess if I have to I will get a new HDD, but that means I will most likely need to get a new OS, and I love windows 7 with all my heart and I don't want to upgrade at windows 8. I feel like it's my OS but it could very well be anything at this point.
Hi @rhhox ,
I have brought your issue to the attention of an appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publically post ( serial numbers and case details).
If you are unfamiliar with how the Forum's private message capability works, you can learn about that here.
Regards,
George
I work for HP -
Windows HP laptop won't boot Windows - possible hard disk failure!
Hi there!
A month ago my HP Pavilion dv6-6b57sa completely froze mid-use, and was unable to move the mouse or get any sort of response.
Naturally I held the power button to hard shutdown and restarted. Ever since then I have been unable to boot Windows 7 (the original OS) properly, and all I could get to was a Startup repair which took days to try to fix the issues, eventually coming up with a message saying it was unable to fix the errors.
Today I decided to ditch the data I had stored and do a fresh install - using the HP wizard by pressing F11 on boot and using a newly created USB Windows 7 install drive. After getting to the point of install process of Windows just loading the files, after choosing a hard drive partition successfully etc. the installation quit, citing a number of issues (screenshots link are below).
So I then try to restart the computer, and get a 'SMART Hard disk error' (screenshot link below) and when I select continue startup from there, it says Windows failed to start (screenshot link below) and then leads to me to the Startup repair manager again - which fails again - (screenshot link also below!)
So after doing a hard drive test, it says it has failed (screenshot link also below).
So what can I do? Is there a serious hardware related issue linked with the hard drive (which is bound to cost lots of £££ I bet), or are there further steps I can take?
Screenshot links: http://1drv.ms/1jnjviU
Many thanks for your help in advance,
MaxYes and you had to at the moment since you won't have a key unless you buy one from Microsoft for about 99 dollars.
Try you best to get the key readble I mean try to read it, good luck!
Sorry because of different timezone I might not be able to help/reply you right away.IF that happens I deeply apologize!
**Click the White thumb if you like the answer.**
**Please mark Accept As Solution if it solves your problem and only solves your problem, if you have any more questions please ask, this also helps others to solve related issues.**
Feel yourself like home here, we are all happy to help, if you have an question reply or start a topic or pm me or an expert. -
App store won't load, what possibly gone wrong?
I just got my MBA.. I was trying to open the app store but it takes so long to load that finally failed.
Anyone with any idea what possibly gone wrong with my machine? Well, internet connections was definitely not the problem since I also browsed at that time.
Thanks a bunch, appreciate it.You need to check to make sure you are actually connected to the network. Tap Settings > WiFi >and then tap the blue ">" next to the network name with checkmark. You should see a complete set of IP address but if the router didn't issue you an IP address properly, you will see your touch IP address start with 169.x. If this is the case, you are connected to the internal network but not to the web.
First thing to do (while you are on that screen) is tap "Forget Network". Then turn WiFi off. Turn it back on and, if needed, tap Other and re-enter your network information. If you continue to have problems, check with your IT department on Monday.
In the meantime, your laptop and iTunes can be used to purchase apps and music. Syncing them with your touch is a great way to get them installed while you are waiting for the answer on your WiFi problem. -
PoweBook g4 won't start up possible logic board failure?
My PB G4 867mh 10.3.9 has entered Hospice mode. Screen stays dark and 3 short beeps occur. Tried to reset the PMU (shift ctrl option start wait 5 sec then start) sometimes works. System profiler states that built in memory slot is empty. with only the 1 gig that I added years ago. from what I have read it appears that this is a logic board issue. After successful "jump start" computer won't wake from sleep- but I don't want to leave it running as it gets very hot.
3 beeps= memory slot= logic board= S.O.L... right?
any suggestions? if anything I'd like to keep it viable to transfer data to new computer(although everything is backed up on ext hard drive).
thanks-Jermsy:
Glad you were able to get booted. The Apple Hardware Test disk is a great tool. However, it is not the best test for RAM and a single run may not detect intermittend issues.
For a more thorough testing of RAM try Rember-Memory Test. In addition, when you boot from the AHT disk, run the tests in a loop by holding down Command + L during the tests. It sometimes takes dozens of repetitions to detect intermittent errors.
at one point little black boxes appeard with white text in them over the screen(reminded me of DOS--are these Kernals?)
What you saw was likely a kernel panic. These can be caused by either hardware or software issues. In your case, I would guess it was hardware.
If this built in RAM(?) has failed I probably need an apple dr. to fix?
Accessing the logic board requires a lot of dismantling, and even after that, I suspect that the RAM module is soldered directly to the logic board, and, as you guessed, would require a trip to the Authorized Apple Repair facility.
Good luck.
cornelius -
I haven't been able to synch for a very long time. I'm finally tired enough of the same music constantly on my ipod that I'm trying again to find some help. I'm computer literate, but not a tech person by any stretch.
According to itunes, I'm not due for a software upgrade until later this month and yet it seems also to reject my request to check for software upgrades. Which seems like there isn't a connection. The fact that it says I'm not due yet makes me think it does happen.
One thing I've gotten lately is the message "itunes isn't my default" and when I go to make it and check everything for itunes and nothing for windows media, nothing changes and I get the message again. This morning I checked "All" and will see if that makes a difference.
I was unable to connect to itunes store until this week. For some reason it worked and I was able to download a movie.
Apple says I have no coverage for help from them -- of course.
Anyone?Sorted it out. If anyone has this problem i reccommend visiting http://forums.ilounge.com/ipod-classic-ipod-5g-video/237546-ipod-classic-80gb-fr eezes-itunes-need-restore-plz-help-2.html#post1403546 there's some pretty good advice on it. have to go into control panel and re-format iPod into NTFS file. good luck.
Maybe you are looking for
-
How can I resize the window size of my website?
My site is http://linguistine.com/ I put the swf in a html page but i'd like the window to be the dimensions of the swf not the html page. Is there an easy way to do this? Thanks Jamie
-
OPTIMAL size for rollback segment in Oracle 8i
In our Database we have 13 Rollback segments & total size of all rollback segments is 33gb. Used % it is showing 99.84%. each rollback segment having near around 4gb of size. I am in confusion to set OPTIMAL value for each rollback segment. can any o
-
Hello all I have two questions: 1)I am having problems joining MM and SD tables qhile creating a query. 2) Are there any tables in SD that get updated when I create a STO and create a delivery in Me21n and VL10g, so that I can use those tables to pul
-
hi am using the below sample to create my OPSS,AM in jdeveloper 11.1.1.6.0,am having error in this class, the error is Error(50,16): cannot find variable IdentityStoreConfigurator and also Error(54,16): cannot find variable IdentityStoreConfigurator
-
Activation failed: Missing external jar
Hi, I'm using an external jar in my WebDynpro development for ESS. I placed this jar file in the lib folder. Everything works fine when deploying to the development server directly. During activation, i got the error which describing the imported cla