Lync 2013 and Audiocodes ESBC Mediant 1000 - poor audio quality
Bit of an odd issue that I've been looking into for the past few weeks - our part of our change from a pilot Lync install to production we have had an Audiocodes ESBC Mediant 1000 installed to serve as a Media Gateway between the Lync Mediation Server and
our Gamma Telecom provided SIP trunk.
However under certain situations my users are reporting exceptionally poor audio quality with the Lync server reporting website reporting a very high packet loss and our ESBC reporting a high 'Average voice delay' (often greater than 80ms).
I have established that by taking these steps the issue can be replicated with almost impunity-
Make incoming call from mobile phone (or landline) - pickup call on Lync Deskphone (CX300/CX500/CX600 and VVX410 all have the same).
Begin a consultative call transfer with an external (another mobile/landline) or internal number which places the incoming call on hold.
Complete the call transfer - at this point the audio quality is still as expected.
Begin a new call from a Lync phone to an external number - at this point the audio quality for the phone call that has been transferred and the new call instantly degrades.
My basic topology is-
Fibre Leased Line - Cat5e cable - Router - Cat5e cable - DMZ Switch - Cat5e cable - Audiocodes Mediant 1000 - Cat5e cable - Servers VLAN - Switch - Fibre - Core switch (layer 3) - Fibre - VMWare Host (ESXI v5) - Lync Server (VMNET 3 adapter)
I have been able to replicate the issue when using both TCP and TLS between the Lync Mediation Server and the Audiocodes gateway.
Over the next day or so I will be looking to get the SIP trunk connected directly to the Lync server to see if that makes any difference (ruling out the Mediant 1000 as a possible cause) but in the meantime does anyone have any ideas as to what could be
causing this most weird situation?
Hi,
Please disassociate the Edge Server from the Mediation and check the delay again.
Please check port 3478 to the internal interface of the Edge Server from all internal clients (including the Mediation Server).
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support
Similar Messages
-
Is Lync 2013 and Office 2010 Home and business compatible?
hi,
Is Lync 2013 and Office 2010 Home and business compatible?
tnxLync 2013 and office 2010 is compatible with limited features
The following features are available only with Office 2010 or Office 2013:
Contact card with expanded options, such as video call and desktop sharing
Quick search from the Find a Contact field in Outlook
Reply with an IM or call from the Outlook Home ribbon in the Mail, Calendar, Contacts, and Tasks folders
Lync Contacts list in Outlook To-Do Bar
Office Backstage (File tab) presence status, program sharing, and file transfer
Presence menu in Microsoft Office SharePoint Workspace 2010 (formerly Microsoft Office Groove 2007)
Presence menu extensibility
Also you can refer below link
http://technet.microsoft.com/en-us/library/gg412817.aspx
For your issue, verify from lync version {for example , if your office 64 bit, Lync must be 64 bit also}
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali -
Lync 2013 and SQL 2012 on the same server
Hi,
I'm in the process of migrating Lync 2010 to Lync 2013. I have a clean install of Windows Server 2012 R2. Is it possible to install Lync 2013 and SQL 2012 on the same server or does it have to be on separate servers.
Thanks
PConfigure Separated SQL Server to use in an Enterprise deployment of Lync Server. Standard Edition servers use a collocated SQL Server Express version of SQL Server that is right sized for the workloads of a Standard Edition server.
Also you can refer below link
http://technet.microsoft.com/en-us/library/gg425848.aspx
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer" -
Lync 2013 and simultaneous ring
We have Lync 2013 and 2010 in our topology with Cisco Call Manager version 8.x. Simultaneous ring worked for a while but is no longer fully functional. Lync client to Lync client calls ring in Lync and on the desktop phone but calls to the desk number do
not ring in Lync. Users are set up in mobility and set for enterprise voice and have a URI. The voice policy has sim ring enabled. I don't see much in the logs but I might be looking in the wrong place. Anywhere I can look on the log server or client side
to narrow it down? I am not the VoIP guy but any help would be appreciated.Check the following document about how to configure simultaneous ring feature between Lync Server and Cisco Unified Communications Manager:
http://www.cisco.com/en/US/solutions/collateral/ns340/ns414/ns728/ns784/1048876.pdf
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software
or information found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Lisa Zheng
TechNet Community Support -
Dear All,
It is always come to be a confusing, about certificate when it comes to lync 2013 and edge. suppose i have domain abc.com and i have to plan to add additional sip domain like xyz.com, abc.com, dfg.com etc. and my default domain would be abc.com so my naming
option would be like this meet.abc.com/sipdomain/meet. I am little confuse how this is teckle in frontend and edge role. Do i have to get new request in edge or have to just import certificate generated in frontend and import into edge.Thanks Eric and Thamara,
So for internal CA, which means i have to install active directory certiificate and no need to buy certificate from public authority. and which include following entries on first front end server admin.defaultsipdomain.com, dialin.defaultsipdomain,
lyncdiscoverinternal.defaultsipdomain, lyncdiscover.defaultsipdomain.com
Or i should i get it from public authority and add all edge and front end requirement and reverse proxy in ucc certificate and use same to import into front end and edge and reverse proxy. -
It's 2013 and I want to convert AIFF audio files to MP3s
It’s 2013 and I want to convert .AIFF audio files to .MP3 files on my Mac.
I created some sound files as .MOVs for a band’s website but that format doesn’t work for some Windows OS users who refuse to fetch a QuickTime plugin for their Explorer or Firefox internet browser…("don’t make them think; it either works or it doesn’t.")
I have been told that MP3 audio files are still the most common audio files on the web and I want the band’s music to be in the most-accessible format.
Thanks,
Ron
Also, this is my first Apple Support question and I would appreciate being pointed to the most appropriate forum(s).Thanks, Joe, that was very useful!
For other people with my problem I should add some of the missing puzzle pieces —
1) A while ago I loaded the songs from the band’s CD onto a previous, now dead, Mac laptop (with a previous Mac OS) and used QuickTime 7 to create down-sampled (and smaller) .mov files. Then I deleted the original .aif files from that computer.
2) Now (back to the present) I wanted the .aif audio files on my new computer to convert them, but the computer doesn’t have a CD/DVD drive. My solution was to use my partner’s iMac.
3) I inserted the CD into the iMac’s drive, clicked "no" to iTunes’ dialog asking if I wanted to import them, created a folder on the desktop, then opened the CD folder on the desktop and copied the songs into the newly-created folder.
4) I copied the new .aif files to a thumbdrive then deleted the .aifs from the iMac.
5) I put the copied thumbdrive .aif songs onto my MacBook Pro Retina (where I had changed iTunes Preferences to MP3) then I 'dropped' the sound file icons onto the iTunes icon in the dock.
5) In iTunes I right-clicked on the songs and chose "Create MP3 Version".
6) Next, I right-clicked on the MP3s in iTunes and chose "Show in Finder". This opened another folder (~/Music/iTunes/iTunes Media/Music/Unknown Artist/Unknown Album/), revealing the MP3s.
7) I created duplicates of the MP3s and moved them to my band's media folder (and will put them on the website after renaming them and editing their webpage for the new audio filenames).
8) Finally, I will delete the .aif and .mp3 songs from my iTunes, using iTunes' interface to ensure it doesn’t get confused.
Sheesh. but I’m still happy to not have a CD/DVD drive on my MacBook Pro. I very rarely use CDs and a drive on the laptop would add bulk and weight while being mostly useless. -
Poor Audio Quality From Exchange 2010 UM
Hi,
I'm experiencing an issue with our Exchange 2010 Unified Messaging system in that the audio quality is suddenly rather poor. We are using Cisco Callmanager 7 for our phone system. When you call an automated attendant, hit the "messages"
button or call the extension to go to voicemail, the audio you hear "crackles," or sounds like it is skipping slightly in that there are brief but noticable interruptions in the audio.
The audio quality issue only occurs when you are connected to voicemail or automated attendants, but not when conversing to other people on phone calls, so that leads me to believe either some interoperability between CM and Exchange UM is malfunctioning, or
just something in UM is a problem. Also, if you listen to voice messages through the computer instead of over the phone, the quality is fine. The problem seems to be mainly with calling in to the UM system.
What can I do to properly troubleshoot this? I have found the Exchange 2010 UM Troubleshooting Assistant, but I have to wait another 2 weeks before I can install Service Pack 1 due to downtime window restrictions. I'm not coming up with a lot of
documentation involving this, so if anyone has any information they think might help me get to the bottom of this I would apprecaite it.
Thank you.Cisco Callmanger and UM are on the same LAN.
I highly doubt that QoS is the culprit here, simply because there aren't any issues with phone calls. If QoS was dropping VOIP packets, then IP phone to IP phone calls would also have poor audio quality. If I call somebody on another IP
phone on the LAN, the audio quality is perfect. It is only when you are connected to the UM system that you hear the poor audio quality -- either listening to voicemail prompts, listening to actual voicemails, listening to the automated attendant --
anything in which UM is on one end of the phone call.
It also seems strange that this is somewhat intermittent. When the issue first occurred, it was definitely happening every time you called in to the UM system and I could repeat the issue by simply pushing my messages button and listening to the welcome
and prompt for a PIN. I restarted the Exchange server at night, and the next day it was intermittent with people calling the help desk to say they were getting poor audio quality from UM but when I tried to repeat the issue I could not.
I also have users complaining of intermittent slowness when using Outlook, which may be totally unrelated. I have been running Perf logs on the Exchange server for the last couple of weeks othe CPU, Network Connections, Exchange RPC totals, etc.
and can't find anything that is using too many resources. -
Nortel CS 1000 v7.5 with Lync 2013 using AudioCodes Mediant 1000 E-SBC
Hi,
I am trying to setup CS 1K to Mediant 1000 E-SBC using SIP trunks. The Mediant will connect to Lync 2013 again using SIP.
I am trying to add Mediant 1000 as a static SIP end point in NRS. Does anyone know of any specific setting that needs to be configured on both NRS as well as Mediant 1000 for it to be registered as an end point.
Also when I try to register the Mediant, SIP 403 forbidden error appears in the syslog of Mediant.
Any inputs will be much appreciated...Hi,
You can refer to the part of “Configuring the ‘Route’ on the Lync Server 2010” in the link below, the document is for Lync server 2010 but similar for Lync server 2013:
http://www.google.co.in/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&ved=0CCUQFjAA&url=http%3A%2F%2Fwww.audiocodes.com%2Ffilehandler.ashx%3Ffileid%3D1623578&ei=ERn7Upn0F9SJqQGpooGoCg&usg=AFQjCNGFePk4Lcx3MxMrriiXDqfYrDqS4w&bvm=bv.61190604,d.aWM
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make
sure that you completely understand the risk before retrieving any suggestions from the above link.
You also need to do the following configuration in Lync, you can check if there any mistake configuration in Lync server caused the error:
SIP trunking connectivity options
Edit Mediation Server Pool
Associate PSTN Gateway
Choose PSTN Gateway object
New trunk configuration
New translation rule
You can refer to the link below of “Configuring Lync 2010 Server to Work with Level 3 SIP Trunking Services”, the document is for Lync server 2010 but similar for Lync server 2013:
http://blogs.technet.com/b/nexthop/archive/2013/04/10/configuring-lync-2010-server-to-work-with-level-3-sip-trunking-services.aspx
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
New Lync 2013 and no mobile to PC calling
I have a new Lync 2013 enterprise server deployment. PC with 2013 client and android phone with 2013 mobile client can both connect and IM fine. but when I make a Lync call it will ring but not answer even if I click accept. It just says
connecting.... I have looked at logs for the PC, phone and on the server but dont see any errors. I am just not sure where to go from here. Any suggestions would be greatly appreciated.
Thanks!!After looking through the massive lync clinet 2010 log for almost 3 hours I finally found this:
02/07/2014|11:14:20.065 1250:120C INFO :: BYE sip:[email protected];opaque=user:epid:F75G9E5FoVmO8RMWQRntYgAA;gruu SIP/2.0 Via: SIP/2.0/TLS 127.0.0.1:50042 Max-Forwards: 70 From: <sip:[email protected]>;tag=967b0de09e;epid=e115ec3448
To: "phone"<sip:[email protected]>;tag=d007b4c5e;epid=212185984839 Call-ID: d6c4a0b89c58477b87650daa0bb16fe9 CSeq: 3 BYE User-Agent: UCCAPI/4.0.7577.0 OC/4.0.7577.0 (Microsoft Lync 2010) ms-client-diagnostics: 23; reason="Call failed to establish
due to a media connectivity failure when one endpoint is internal and the other is remote";CallerMediaDebug="audio:ICEWarn=0x2b,LocalSite=10.1.1.158:14842,LocalMR=pu.bl.ic.ip-AV:3478,RemoteSite=10.38.210.159:19600,PortRange=1025:65000,LocalLocation=1,RemoteLocation=2,FederationType=0"
Proxy-Authorization: NTLM qop="auth", realm="SIP Communications Service", opaque="E84145BE", targetname="FrontEndSrv1.domain.local", crand="f5c0735e", cnum="28", response="0100000065633334d5df23b80d7f3491" Content-Length: 0
02/07/2014|11:14:20.065 1250:120C INFO :: End of Sending Packet - pu.bl.ic.ip-sip:443 (From Local Address: 127.0.0.1:50042) 994 bytes
someone please tell me you know exactly what I need to do to fix it. THANKS!!! -
Issues with mobility and autodiscovery with Lync 2013 and IIS/ARR
Hi all,
this is my last resort after days and days searching a solution for this problem... unsuccessfully.
All works fine unless the autodiscovery service with external users and the mobility service for both internal and external ones.
I deployed a Standard Edition Lync Server 2013 with:
a consolidated Frontend server in LAN
an Archiving and Monitoring server in LAN
an Edge server in DMZ with 2 NICs (one in DMZ network and one in LAN)
a IIS/ARR 2.5 reverse proxy in DMZ with 2 NICs (one in DMZ network and one in LAN)
All these roles are on Windows Server 2012 R2.
No split-DNS is deployed since I have different domains for internal and external. In any case I used the pinpoint DNS tip to resolve some records internally (I followed this guide http://tsoorad.blogspot.ch/2012/10/lync-server-dns-pinpoint-zones.html)
Here DNS records into internal domain:
A-record for meet.domain-ext.com points to Frontend server local IP
A-record for dialin.domain-ext.com points to Frontend server local IP
A-record for lyncdiscoverinternal.domain-ext.com points to Frontend server IP
A-record for lyncwebexternal.domain-ext.com points to Frontend sever local IP
A-record for autodiscover.domain-ext.com points to Exchange server local IP
Here DNS records into external domain:
CNAME-record for lyncdiscover.domain-ext.com points to lyncwebexternal.domain-ext.com
CNAME-record for sipexternal.domain-ext.com points to lyncwebexternal.domain-ext.com
A-record for meet.domain-ext.com points to Reverse Proxy public IP
A-record for dialin.domain-ext.com points to Reverse Proxy public IP
A-record for lyncwebexternal.domain-ext.com points to Reverse Proxy public IP
I installed and configured IIS/ARR 2.5 with KB2732764 and KB2785586 on Reverse Proxy following the NextHop guide. The local IP address of external NIC on Reverse Proxy is NATTED by a Cisco ASA firewall with public IP address and only 80/443
ports are permitted.
The problems occurs when I try to connect whit my Lync 2013 APP on iPad using autodiscovery service, both internally and externally. After some seconds the APP shows the message “Cannot connect to the server because it could be busy or
temporarily unavailable. Retry.” When I used the IIS/ARR 3.0 the problem looked like an authentication issue, then I came back to ISS/ARR 2.5 version with its KB. Now I cannot understand what is the cause about logfail.
The same behavior occurs with Android Lync 2013 APP and Windows Phone 8 APP.
Moreover my Lync 2013 client on Windows 7 can connect internally with autodiscovery settings but it cannot do it externally.
I'm a bit confused because I cannot understand if the problem is about external webservice of Frontend server or about Reverse Proxy configuration or about Lync Control Panel configuration.
Here is an extracted of iPad Lync 2013 log (sorry if it’s a bit long).
Any helps are very appreciated, thansk a lot!
</SentRequest>
2013-12-20
11:33:00.781 Lync[563:3a71018c] INFO APPLICATION
CUrlRedirectAndTrustResolver.cpp/201:CUrlRedirectAndTrustResolver::processUrl
called with url = http://lyncdiscover.domain-ext.com/, hopCount = 0, maxHops =
10
2013-12-20
11:33:00.781 Lync[563:6d00000] INFO UTILITIES
CHttpStreamPool.cpp/409:Allocating stream 0x11cbe40 for url -
https://lyncdiscover.domain-ext.com/ with persistent id as 6
2013-12-20
11:33:00.782 Lync[563:3a71018c] INFO TRANSPORT CTransportThread.cpp/131:Added
Request(UcwaAutoDiscoveryRequest) to Request Processor queue
2013-12-20
11:33:00.782 Lync[563:6d00000] VERBOSE TRANSPORT
CHttpProxyHelper.cpp/436:CHttpProxyHelper::discoverProxy : No proxy found for
url https://lyncdiscover.domain-ext.com/?sipuri=sip:[email protected].
Sending over direct connection.
2013-12-20
11:33:00.782 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/385:Submitting new req.
UrlTrustResolver(0x1201358)
2013-12-20
11:33:00.782 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryService.cpp/1783:Successfully started the GetUserUrlOperation
request for http://lyncdiscover.domain-ext.com/?sipuri=sip:[email protected]
2013-12-20
11:33:00.796 Lync[563:6d00000] INFO TRANSPORT CTransportThread.cpp/343:Sent
Request(UcwaAutoDiscoveryRequest) to Request Processor
2013-12-20
11:33:00.796 Lync[563:6d00000] WARNING TRANSPORT
CCredentialManager.cpp/317:CCredentialManager::getSpecificCredential returning
NULL credential for serviceId (4) type (1)!
2013-12-20
11:33:00.797 Lync[563:6d00000] INFO TRANSPORT
TransportUtilityFunctions.cpp/631:<SentRequest>
GET
http://lyncdiscover.domain-ext.com/
Request Id:
0x1201358
HttpHeader:Accept
application/vnd.microsoft.rtc.autodiscover+xml;v=1
</SentRequest>
2013-12-20
11:33:00.797 Lync[563:6d00000] INFO UTILITIES
CHttpStreamPool.cpp/409:Allocating stream 0x12028f0 for url -
http://lyncdiscover.domain-ext.com/ with persistent id as 7
2013-12-20
11:33:00.798 Lync[563:6d00000] VERBOSE TRANSPORT
CHttpProxyHelper.cpp/436:CHttpProxyHelper::discoverProxy : No proxy found for
url http://lyncdiscover.domain-ext.com/. Sending over direct connection.
2013-12-20
11:33:00.798 Lync[563:6d00000] INFO TRANSPORT CHttpStreamPool.cpp/556:Not
setting TLS as the url(http://lyncdiscover.domain-ext.com/) is not https
2013-12-20
11:33:00.812 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:33:00.812 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:33:00.812 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:33:00.813 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:33:00.813 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:33:04.104 Lync[563:6d00000] INFO UTILITIES CHttpConnection.cpp/577:Received
kCFStreamEventEndEncountered (UcwaAutoDiscoveryRequest)isHeadersAvailable =
true responseHeadersHandle = 12c5d70
2013-12-20
11:33:04.105 Lync[563:6d00000] INFO UTILITIES CHttpConnection.cpp/628:Response
status = 200 for request UcwaAutoDiscoveryRequest
2013-12-20
11:33:04.105 Lync[563:6d00000] INFO UTILITIES
CHttpStreamPool.cpp/455:Scheduling stream 0x12028f0 for release.
2013-12-20
11:33:04.105 Lync[563:6d00000] INFO TRANSPORT
CHttpRequestProcessor.cpp/173:Received response of
request(UcwaAutoDiscoveryRequest) with status = 0x0
2013-12-20
11:33:04.106 Lync[563:6d00000] INFO TRANSPORT
TransportUtilityFunctions.cpp/925:<ReceivedResponse>
GET
http://lyncdiscover.domain-ext.com/
Request Id:
0x1201358
HttpHeader:Cache-Control
no-cache
HttpHeader:Content-Length
1076
HttpHeader:Content-Type
application/vnd.microsoft.rtc.autodiscover+xml; v=1
HttpHeader:Date
Fri, 20 Dec 2013 10:33:02 GMT
HttpHeader:Expires
-1
HttpHeader:Pragma
no-cache
HttpHeader:Server
Microsoft-IIS/8.5
HttpHeader:StatusCode
200
HttpHeader:X-AspNet-Version
4.0.30319
HttpHeader:X-Content-Type-Options
nosniff
HttpHeader:X-MS-Server-Fqdn
frontend-lync.domain-int.com
HttpHeader:X-Powered-By
ASP.NET, ARR/2.5
Ôªø<?xml
version="1.0" encoding="utf-8"?><AutodiscoverResponse
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
AccessLocation="Internal"><Root><Link
token="Domain" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root/domain?originalDomain=domain-ext.com"
/><Link token="User" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=domain-ext.com"
/><Link token="Self" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root?originalDomain=domain-ext.com"
/><Link token="OAuth" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root/oauth/user?originalDomain=domain-ext.com"
/><Link token="External/XFrame"
href="https://lyncwebexternal.domain-ext.com/Autodiscover/XFrame/XFrame.html"
/><Link token="Internal/XFrame" href="https://frontend-lync.domain-int.com/Autodiscover/XFrame/XFrame.html"
/><Link token="XFrame" href="https://lyncwebexternal.domain-ext.com/Autodiscover/XFrame/XFrame.html"
/></Root></AutodiscoverResponse>
</ReceivedResponse>
2013-12-20
11:33:04.108 Lync[563:6d00000] INFO TRANSPORT
CUcwaAutoDiscoveryResponse.cpp/112:location value is internal
2013-12-20
11:33:04.108 Lync[563:6d00000] INFO TRANSPORT
CUcwaAutoDiscoveryResponse.cpp/195:User url is https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:33:04.109 Lync[563:6d00000] INFO TRANSPORT
CHttpRequestProcessor.cpp/266:Sending event to main thread for
request(0x1201358)
2013-12-20
11:33:04.109 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/822:Req. completed, Stopping timer.
2013-12-20
11:33:04.109 Lync[563:3a71018c] INFO APPLICATION
CUrlRedirectAndTrustResolver.cpp/610:UrlRedirectAndTrustResolver complete with
url = http://lyncdiscover.domain-ext.com/, Hops = 1, status = S_OK (S0-0-0)
2013-12-20
11:33:04.109 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/725:Response received for req.
UrlTrustResolver(0x1201358): S_OK (S0-0-0) (Success); Done with req.; Stopping
resend timer
2013-12-20
11:33:04.110 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryGetUserUrlOperation.cpp/393:CUcwaAutoDiscoverGetUserUrlOperation::onEvent
received. Status = S_OK (S0-0-0), url =
http://lyncdiscover.domain-ext.com/
2013-12-20
11:33:04.110 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryGetUserUrlOperation.cpp/449:Received a root response
2013-12-20
11:33:04.110 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryGetUserUrlOperation.cpp/456:Running trust check on user url.
url = https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:33:04.110 Lync[563:3a71018c] INFO APPLICATION
CUrlRedirectAndTrustResolver.cpp/77:Starting CUrlRedirectAndTrustResolver with
url = https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com,
maxHops = 1
2013-12-20
11:33:04.110 Lync[563:3a71018c] INFO APPLICATION
CUrlRedirectAndTrustResolver.cpp/201:CUrlRedirectAndTrustResolver::processUrl
called with url = https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user,
hopCount = 0, maxHops = 1
2013-12-20
11:33:04.111 Lync[563:3a71018c] INFO TRANSPORT CTransportThread.cpp/131:Added
Request(UcwaAutoDiscoveryRequest) to Request Processor queue
2013-12-20
11:33:04.111 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/385:Submitting new req.
UrlTrustResolver(0x11d4d38)
2013-12-20
11:33:04.111 Lync[563:6d00000] INFO TRANSPORT CTransportThread.cpp/343:Sent
Request(UcwaAutoDiscoveryRequest) to Request Processor
2013-12-20
11:33:04.111 Lync[563:6d00000] WARNING TRANSPORT
CCredentialManager.cpp/317:CCredentialManager::getSpecificCredential returning
NULL credential for serviceId (4) type (1)!
2013-12-20
11:33:04.112 Lync[563:6d00000] INFO TRANSPORT
TransportUtilityFunctions.cpp/631:<SentRequest>
GET
https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user
Request Id:
0x11d4d38
HttpHeader:Accept
application/vnd.microsoft.rtc.autodiscover+xml;v=1
</SentRequest>
2013-12-20
11:33:04.112 Lync[563:6d00000] INFO UTILITIES
CHttpStreamPool.cpp/409:Allocating stream 0x125fa90 for url - https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user
with persistent id as 7
2013-12-20
11:33:04.112 Lync[563:6d00000] VERBOSE TRANSPORT
CHttpProxyHelper.cpp/436:CHttpProxyHelper::discoverProxy : No proxy found for
url https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user.
Sending over direct connection.
2013-12-20
11:33:04.113 Lync[563:6d00000] INFO UTILITIES CHttpStreamPool.cpp/609:Releasing
stream 0x12028f0.
2013-12-20
11:33:04.261 Lync[563:6d00000] INFO UTILITIES CHttpConnection.cpp/577:Received
kCFStreamEventEndEncountered (UcwaAutoDiscoveryRequest)isHeadersAvailable =
true responseHeadersHandle = 11cfbd0
2013-12-20
11:33:04.262 Lync[563:6d00000] INFO UTILITIES CHttpConnection.cpp/628:Response
status = 200 for request UcwaAutoDiscoveryRequest
2013-12-20
11:33:04.262 Lync[563:6d00000] INFO UTILITIES
CHttpStreamPool.cpp/455:Scheduling stream 0x11cbe40 for release.
2013-12-20
11:33:04.263 Lync[563:6d00000] INFO TRANSPORT
CHttpRequestProcessor.cpp/173:Received response of
request(UcwaAutoDiscoveryRequest) with status = 0x0
2013-12-20
11:33:04.263 Lync[563:6d00000] INFO TRANSPORT
TransportUtilityFunctions.cpp/925:<ReceivedResponse>
GET
https://lyncdiscover.domain-ext.com/?sipuri=sip:[email protected]
Request Id:
0x12450d8
HttpHeader:Cache-Control
no-cache
HttpHeader:Content-Length
1076
HttpHeader:Content-Type
application/vnd.microsoft.rtc.autodiscover+xml; v=1
HttpHeader:Date
Fri, 20 Dec 2013 10:33:02 GMT
HttpHeader:Expires
-1
HttpHeader:Pragma
no-cache
HttpHeader:Server
Microsoft-IIS/8.5
HttpHeader:StatusCode
200
HttpHeader:X-AspNet-Version
4.0.30319
HttpHeader:X-Content-Type-Options
nosniff
HttpHeader:X-MS-Server-Fqdn
frontend-lync.domain-int.com
HttpHeader:X-Powered-By
ASP.NET, ARR/2.5
Ôªø<?xml
version="1.0" encoding="utf-8"?><AutodiscoverResponse
xmlns:xsd="http://www.w3.org/2001/XMLSchema"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
AccessLocation="Internal"><Root><Link
token="Domain" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root/domain?originalDomain=domain-ext.com"
/><Link token="User" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=domain-ext.com"
/><Link token="Self" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root?originalDomain=domain-ext.com"
/><Link token="OAuth" href="https://frontend-lync.domain-int.com/Autodiscover/AutodiscoverService.svc/root/oauth/user?originalDomain=domain-ext.com"
/><Link token="External/XFrame"
href="https://lyncwebexternal.domain-ext.com/Autodiscover/XFrame/XFrame.html"
/><Link token="Internal/XFrame" href="https://frontend-lync.domain-int.com/Autodiscover/XFrame/XFrame.html"
/><Link token="XFrame" href="https://lyncwebexternal.domain-ext.com/Autodiscover/XFrame/XFrame.html"
/></Root></AutodiscoverResponse>
</ReceivedResponse>
2013-12-20
11:33:04.264 Lync[563:6d00000] INFO TRANSPORT
CUcwaAutoDiscoveryResponse.cpp/112:location value is internal
2013-12-20
11:33:04.265 Lync[563:6d00000] INFO TRANSPORT
CUcwaAutoDiscoveryResponse.cpp/195:User url is https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:33:04.265 Lync[563:6d00000] INFO TRANSPORT
CHttpRequestProcessor.cpp/266:Sending event to main thread for
request(0x12450d8)
2013-12-20
11:33:04.266 Lync[563:3a71018c] INFO APPLICATION CTransportRequestRetrialQueue.cpp/822:Req.
completed, Stopping timer.
2013-12-20
11:33:04.266 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryGetUserUrlOperation.cpp/290:Received a root response
2013-12-20
11:33:04.266 Lync[563:3a71018c] INFO APPLICATION CUcwaAutoDiscoveryGetUserUrlOperation.cpp/224:UcwaAutoDiscoveryGetUserUrlOperation
completed with url = https://lyncdiscover.domain-ext.com/?sipuri=sip:[email protected],
userUrl = https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com,
status = S_OK (S0-0-0)
2013-12-20
11:33:04.266 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/725:Response received for req.
GET-UnAuthenticatedGet(0x12450d8): S_OK (S0-0-0) (Success); Done with req.; Stopping
resend timer
2013-12-20
11:33:04.267 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/399:Cancelling all requests
2013-12-20
11:33:04.267 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/409:Cancelling request: 0x11d4d38
2013-12-20
11:33:04.267 Lync[563:3a71018c] INFO TRANSPORT CSessionBase.hxx/158:Cancelling
request: 0x11d4d38
2013-12-20
11:33:04.267 Lync[563:3a71018c] INFO TRANSPORT CTransportThread.cpp/163:Added
Request(UcwaAutoDiscoveryRequest) to Request Processor queue
2013-12-20
11:33:04.267 Lync[563:3a71018c] INFO APPLICATION
CUrlRedirectAndTrustResolver.cpp/610:UrlRedirectAndTrustResolver complete with
url = https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user,
Hops = 1, status = W_Cancelled (W0-0-6)
2013-12-20
11:33:04.267 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryGetUserUrlOperation.cpp/224:UcwaAutoDiscoveryGetUserUrlOperation
completed with url = http://lyncdiscover.domain-ext.com/?sipuri=sip:[email protected],
userUrl = , status = W_Cancelled (W0-0-6)
2013-12-20
11:33:04.268 Lync[563:6d00000] INFO TRANSPORT CTransportThread.cpp/343:Sent
Request(UcwaAutoDiscoveryRequest) to Request Processor
2013-12-20
11:33:04.268 Lync[563:3a71018c] INFO TRANSPORT CCredentialManager.cpp/176:getSpecificCredential
for serviceId(1) returning: credType (1) signInName ([email protected])
domain () username (mattia.spagnoli) password.empty() (0) certificate.isValid()
(0) privateKey.empty() (1) compatibleServiceIds(1)
2013-12-20
11:33:04.268 Lync[563:3a71018c] INFO TRANSPORT
CMetaDataManager.cpp/403:Received a request to get the meta data of type 0 for
url https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:33:04.269 Lync[563:3a71018c] INFO TRANSPORT CMetaDataManager.cpp/467:Sending
Unauthenticated get to get the web-ticket url
2013-12-20
11:33:04.269 Lync[563:3a71018c] INFO TRANSPORT CTransportThread.cpp/131:Added
Request() to Request Processor queue
2013-12-20
11:33:04.269 Lync[563:3a71018c] INFO TRANSPORT
CAuthenticationResolver.cpp/109:Waiting on Meta Data from https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:33:04.269 Lync[563:62d4000] INFO TRANSPORT CTransportThread.cpp/343:Sent
Request() to Request Processor
2013-12-20
11:33:04.270 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/385:Submitting new req.
GET-AuthenticatedUserGetRequest(0x1201ab8)
2013-12-20
11:33:04.270 Lync[563:62d4000] WARNING TRANSPORT
CCredentialManager.cpp/317:CCredentialManager::getSpecificCredential returning
NULL credential for serviceId (4) type (1)!
2013-12-20
11:33:04.270 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryService.cpp/1189:Submitting Authenticated AutoDiscovery
request to https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:33:04.270 Lync[563:6d00000] INFO UTILITIES
CHttpStreamPool.cpp/455:Scheduling stream 0x125fa90 for release.
2013-12-20
11:33:04.271 Lync[563:62d4000] INFO TRANSPORT
TransportUtilityFunctions.cpp/631:<SentRequest>
GET
https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
Request Id:
0x1206198
HttpHeader:Accept
HttpHeader:X-MS-WebTicket
xxxxxxxxxx
</SentRequest>
2013-12-20
11:33:04.271 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryService.cpp/1662:Ignoring GetUserUrlOperation event as
current state is 6
2013-12-20
11:33:04.271 Lync[563:62d4000] INFO UTILITIES
CHttpStreamPool.cpp/409:Allocating stream 0x11c0a40 for url - https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user
with persistent id as 15
2013-12-20
11:33:04.271 Lync[563:3a71018c] INFO APPLICATION CUcwaAutoDiscoveryService.cpp/1664:Request
url was http://lyncdiscover.domain-ext.com/?sipuri=sip:[email protected]
2013-12-20
11:33:04.272 Lync[563:62d4000] VERBOSE TRANSPORT
CHttpProxyHelper.cpp/436:CHttpProxyHelper::discoverProxy : No proxy found for
url https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com.
Sending over direct connection.
2013-12-20
11:33:20.621 Lync[563:3a71018c] INFO UTILITIES
CNetworkMonitor.cpp/217:Reachabilility Flags IsWWAN(0):Reachable(0):TransientConnection(0):ConnectionRequired(0):ConnectionOnTraffic(0):InterventionRequired(0):ConnectionOnDemand(0):IsLocalAddress(0):IsDirect(0)
2013-12-20
11:33:20.623 Lync[563:3a71018c] INFO UTILITIES CNetworkMonitor.cpp/186:Updated
networkAvailableToConnect(CellularDataNetwork) -> NoNetwork,
isInAirplaneMode(0) -> 1
2013-12-20
11:33:20.623 Lync[563:3a71018c] INFO APPLICATION
CUcmpConversationsManager.cpp/4091:CUcmpConversationsManager::canDoVideoBasedOnNetworkAndPolicy
returns false because RequestWiFiForAudio or RequestWifiForVideo is true and
current network : is not WiFi
2013-12-20
11:33:20.623 Lync[563:3a71018c] INFO APPLICATION
CUcmpConversationsManager.cpp/1672:CUcmpConversationsManager::queryCapability
on StartP2PVideoCall returns false because
canDoVideoBasedOnNetworkAndPolicy
returned false
2013-12-20
11:33:20.904 Lync[563:3a71018c] INFO UTILITIES
CNetworkMonitor.cpp/217:Reachabilility Flags
IsWWAN(1):Reachable(1):TransientConnection(1):ConnectionRequired(0):ConnectionOnTraffic(0):InterventionRequired(0):ConnectionOnDemand(0):IsLocalAddress(1):IsDirect(0)
2013-12-20
11:33:20.905 Lync[563:3a71018c] INFO UTILITIES CNetworkMonitor.cpp/186:Updated
networkAvailableToConnect(NoNetwork) -> CellularDataNetwork,
isInAirplaneMode(1) -> 0
2013-12-20
11:33:20.905 Lync[563:3a71018c] INFO TRANSPORT CEventChannelManager.cpp/826:Received
network monitor event so restarting event channel.
2013-12-20
11:33:20.906 Lync[563:3a71018c] INFO TRANSPORT
CEventChannelManager.cpp/520:Moving the event channel aggressive mode.
2013-12-20
11:33:20.906 Lync[563:3a71018c] INFO APPLICATION
CUcmpConversationsManager.cpp/4091:CUcmpConversationsManager::canDoVideoBasedOnNetworkAndPolicy
returns false because RequestWiFiForAudio or RequestWifiForVideo is true and
current network : is not WiFi
2013-12-20
11:33:20.906 Lync[563:3a71018c] INFO APPLICATION
CUcmpConversationsManager.cpp/1672:CUcmpConversationsManager::queryCapability
on StartP2PVideoCall returns false because
canDoVideoBasedOnNetworkAndPolicy
returned false
2013-12-20
11:33:20.906 Lync[563:3a71018c] INFO APPLICATION CUcwaAutoDiscoveryService.cpp/2070:adIsEnabled
= 1, sipUri = sip:[email protected], m_internalADUrlInput =
m_externalADUrlInput =
2013-12-20
11:33:20.906 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryService.cpp/255:Discovery is in progress and process state is
6Ignoring request to start network discovery
2013-12-20
11:34:04.274 Lync[563:62d4000] INFO UTILITIES
CHttpStreamPool.cpp/455:Scheduling stream 0x11c0a40 for release.
2013-12-20
11:34:04.275 Lync[563:62d4000] ERROR UTILITIES CHttpConnection.cpp/517:Connection
timedout for request (0x%u0x12d1ea0) - notifying error E_ConnectionTimeoutError
2013-12-20
11:34:04.275 Lync[563:62d4000] INFO TRANSPORT
CHttpRequestProcessor.cpp/173:Received response of request() with status =
0x22020005
2013-12-20
11:34:04.276 Lync[563:62d4000] INFO TRANSPORT
CHttpRequestProcessor.cpp/201:Request
resulted in E_ConnectionTimeoutError (E2-2-5). The retry counter is: 0
2013-12-20
11:34:04.276 Lync[563:62d4000] INFO TRANSPORT
CHttpRequestProcessor.cpp/266:Sending event to main thread for
request(0x1206198)
2013-12-20
11:34:04.277 Lync[563:3a71018c] INFO TRANSPORT
CMetaDataManager.cpp/581:Received response for meta data request of type 60
with status 570556421
2013-12-20
11:34:04.277 Lync[563:3a71018c] ERROR TRANSPORT CMetaDataManager.cpp/597:Unable
to get a response to an unauthenticated get to url https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:34:04.278 Lync[563:3a71018c] INFO TRANSPORT CAuthenticationResolver.cpp/210:MetaData
retrieval for url https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
completed with status 570556421
2013-12-20
11:34:04.278 Lync[563:3a71018c] INFO TRANSPORT CAuthenticationResolver.cpp/239:Deleting
1 pended Meta data requests for url https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:34:04.278 Lync[563:3a71018c] ERROR TRANSPORT CAuthenticationResolver.cpp/288:Unable
to get the meta data for server url https://frontend-lync.domain-int.com/autodiscover/autodiscoverservice.svc/root/user?originaldomain=domain-ext.com
2013-12-20
11:34:04.279 Lync[563:3a71018c] INFO TRANSPORT
CAuthenticationResolver.cpp/293:Failing request to the request manager
2013-12-20
11:34:04.279 Lync[563:3a71018c] INFO TRANSPORT CRequestManager.cpp/273:Failing
secure request UcwaAutoDiscoveryRequest with status E_ConnectionTimeoutError
(E2-2-5)
2013-12-20
11:34:04.279 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/822:Req. completed, Stopping timer.
2013-12-20
11:34:04.279 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryService.cpp/1284:Received autodiscovery response with status
E_ConnectionTimeoutError (E2-2-5)
2013-12-20
11:34:04.279 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryService.cpp/1242:Raising Autodiscovery event with status
E_ConnectionTimeoutError (E2-2-5) for eventType 0
2013-12-20
11:34:04.280 Lync[563:3a71018c] INFO APPLICATION CUcwaAutoDiscoveryServiceRetrialWrapper.cpp/417:Received
event for type 0 with status E_ConnectionTimeoutError (E2-2-5)
2013-12-20
11:34:04.280 Lync[563:3a71018c] INFO APPLICATION
CUcwaAutoDiscoveryServiceRetrialWrapper.cpp/496:Raising Autodiscovery event
with status E_ConnectionTimeoutError (E2-2-5) for eventType 0
2013-12-20
11:34:04.280 Lync[563:3a71018c] ERROR APPLICATION
CUcwaAppSession.cpp/2066:Auto-discovery failed, aborting sign-in!
2013-12-20
11:34:04.280 Lync[563:3a71018c] INFO APPLICATION CUcwaAppSession.cpp/998:CUcwaAppSession::setNewActualState()
state=0
2013-12-20
11:34:04.294 Lync[563:3a71018c] INFO UTILITIES
CBasePersistableComponent.cpp/230:Storing 7 out-of-sync components took 10ms
2013-12-20
11:34:04.295 Lync[563:3a71018c] INFO UTILITIES CiOsAppStateQuery.h/147:Clearing
keep-alive timer callback
2013-12-20
11:34:04.295 Lync[563:6d00000] INFO TRANSPORT
CHttpRequestProcessor.cpp/134:Clearing request processor for component
UcwaAutoDiscoverySession on sign-out.
2013-12-20
11:34:04.295 Lync[563:62d4000] INFO TRANSPORT
CHttpRequestProcessor.cpp/134:Clearing request processor for component
MetaDataManager on sign-out.
2013-12-20
11:34:04.295 Lync[563:3a71018c] INFO APPLICATION CAlertReporter.cpp/64:Alert
received! Category 1, Type 201, level 0, error E_ConnectionTimeoutError
(E2-2-5), context '', hasAction=false
2013-12-20
11:34:04.296 Lync[563:6d00000] INFO UTILITIES CHttpStreamPool.cpp/609:Releasing
stream 0x11cbe40.
2013-12-20
11:34:04.296 Lync[563:62d4000] INFO UTILITIES CHttpStreamPool.cpp/609:Releasing
stream 0x11c0a40.
2013-12-20
11:34:04.296 Lync[563:3a71018c] INFO APPLICATION CAlertReporter.cpp/117:Alert
cleared of Category 1, Type 201, cleared 0 alerts
2013-12-20
11:34:04.297 Lync[563:3a71018c] INFO APPLICATION
CTransportRequestRetrialQueue.cpp/725:Response received for req.
GET-AuthenticatedUserGetRequest(0x1201ab8): E_ConnectionTimeoutError (E2-2-5)
(RemoteNetworkTemporaryError); Done with req.; Stopping resend timer
2013-12-20
11:34:04.298 Lync[563:3a71018c] INFO UI CMAudioUtil.mm/322:stopSound
2013-12-20
11:34:04.298 Lync[563:3a71018c] INFO UI CMAudioUtil.mm/322:stopSound
2013-12-20
11:34:04.298 Lync[563:3a71018c] INFO UI CMAudioUtil.mm/322:stopSound
2013-12-20
11:34:04.298 Lync[563:3a71018c] INFO UI CMAudioVideoToastViewController.mm/992:Cancelling
local notification
2013-12-20
11:34:04.299 Lync[563:6d00000] INFO UTILITIES CHttpStreamPool.cpp/609:Releasing
stream 0x125fa90.
2013-12-20
11:34:04.300 Lync[563:3a71018c] INFO UI CMRootViewController.mm/378:ActualState
= 0 DesiredState = 2 DataAvailable = 0
2013-12-20
11:34:04.300 Lync[563:3a71018c] INFO UI
CMDetailViewController.mm/229:ActualState = 0 DesiredState = 1 DataAvailable = 0
2013-12-20
11:34:04.300 Lync[563:3a71018c] INFO UI CMDetailViewController.mm/262:ActualState
= IsSignedOut DesiredState = BeSignedIn DataAvailable = 0 Showing UI =
CredentialTableViewController
2013-12-20
11:34:04.300 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.301 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.301 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.301 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.301 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.301 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/705:desired
view is alert, size 1
2013-12-20
11:34:04.301 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/745:adding the
desired view
2013-12-20
11:34:04.302 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/480:reposition
floating views
2013-12-20
11:34:04.302 Lync[563:3a71018c] INFO UI CMAlertViewController.mm/110:showalert
is 1
2013-12-20
11:34:04.302 Lync[563:3a71018c] INFO UI CMAlertViewController.mm/114:showalert
is 0
2013-12-20
11:34:04.302 Lync[563:3a71018c] INFO UI CMUIUtil.mm/402:Mapping error code =
0x22020005, context = , type = 201
2013-12-20 11:34:04.303 Lync[563:3a71018c] INFO UI
CMUIUtil.mm/1680:Mapped error message is 'Non riesco a connettermi al server
perché potrebbe essere occupato o temporaneamente non disponibile. Riprova.
2013-12-20
11:34:04.304 Lync[563:3a71018c] ERROR UI
CMDismissButtonBaseViewController.mm/89:before: view height 1024.000000, width
45.000000, x 64.000000, y 0.000000
2013-12-20
11:34:04.304 Lync[563:3a71018c] INFO UI
CMNotificationManager.mm/1089:viewFrame: origin x 64.000000, origin y 0.000000,
height 1024.000000, width 45.000000
2013-12-20
11:34:04.304 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/1195:resize
alert label, origin x 44.000000, origin y 2.000000, height 41.000000, width
936.000000
2013-12-20
11:34:04.305 Lync[563:3a71018c] ERROR UI CMDismissButtonBaseViewController.mm/104:after:
self.label.frame height 41.000000, width 936.000000, x 44.000000, y 2.000000
2013-12-20
11:34:04.305 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.305 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.305 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.305 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.305 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.306 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/705:desired
view is alert, size 1
2013-12-20
11:34:04.306 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/718:desired
view is same as the current view
2013-12-20
11:34:04.306 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/480:reposition
floating views
2013-12-20
11:34:04.306 Lync[563:3a71018c] INFO UI CMAlertViewController.mm/110:showalert
is 0
2013-12-20
11:34:04.306 Lync[563:3a71018c] ERROR UI
CMDismissButtonBaseViewController.mm/89:before: view height 1024.000000, width
45.000000, x 64.000000, y 0.000000
2013-12-20
11:34:04.307 Lync[563:3a71018c] INFO UI
CMNotificationManager.mm/1089:viewFrame: origin x 64.000000, origin y 0.000000,
height 1024.000000, width 45.000000
2013-12-20
11:34:04.307 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/1195:resize
alert label, origin x 44.000000, origin y 2.000000, height 41.000000, width
936.000000
2013-12-20
11:34:04.307 Lync[563:3a71018c] ERROR UI
CMDismissButtonBaseViewController.mm/104:after: self.label.frame height
41.000000, width 936.000000, x 44.000000, y 2.000000
2013-12-20
11:34:04.337 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.337 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.338 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.338 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.338 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.338 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/705:desired
view is alert, size 1
2013-12-20
11:34:04.338 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/718:desired
view is same as the current view
2013-12-20
11:34:04.338 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/480:reposition
floating views
2013-12-20
11:34:04.339 Lync[563:3a71018c] INFO UI CMAlertViewController.mm/110:showalert is
0
2013-12-20
11:34:04.339 Lync[563:3a71018c] ERROR UI
CMDismissButtonBaseViewController.mm/89:before: view height 1024.000000, width
45.000000, x 64.000000, y 0.000000
2013-12-20
11:34:04.339 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/1089:viewFrame:
origin x 64.000000, origin y 0.000000, height 1024.000000, width 45.000000
2013-12-20
11:34:04.339 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/1195:resize
alert label, origin x 44.000000, origin y 2.000000, height 41.000000, width
936.000000
2013-12-20
11:34:04.339 Lync[563:3a71018c] ERROR UI
CMDismissButtonBaseViewController.mm/104:after: self.label.frame height
41.000000, width 936.000000, x 44.000000, y 2.000000
2013-12-20
11:34:04.340 Lync[563:3a71018c] INFO UI CMSplitViewController.mm/162:Details
Pane is in Full screen with controller
2013-12-20
11:34:04.340 Lync[563:3a71018c] INFO UI CMSplitViewController.mm/204:Split view
frame orientation UIInterfaceOrientationLandscapeLeft Height = 748.000000 Width
= 1024.000000 origin.x = 20.000000 origin.y = 0.000000 keyboardHeight =
0.000000
2013-12-20
11:34:04.341 Lync[563:3a71018c] INFO UI CMSplitViewController.mm/162:Details
Pane is in Full screen with controller
2013-12-20
11:34:04.341 Lync[563:3a71018c] INFO UI CMSplitViewController.mm/204:Split view
frame orientation UIInterfaceOrientationLandscapeLeft Height = 748.000000 Width
= 1024.000000 origin.x = 20.000000 origin.y = 0.000000 keyboardHeight =
0.000000
2013-12-20
11:34:04.343 Lync[563:3a71018c] INFO UI
CMToolsViewController.mm/349:ActualState = 0 DesiredState = 1 DataAvailable = 0
2013-12-20
11:34:04.344 Lync[563:3a71018c] INFO UI
CMAlertViewController.mm/93:ObservableListItem Added event received
2013-12-20
11:34:04.344 Lync[563:3a71018c] INFO UI CMAlertViewController.mm/103:showalert
is 1
2013-12-20
11:34:04.344 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.344 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.344 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.344 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.345 Lync[563:3a71018c] INFO UI CMConversationCommon.mm/43:not signed
in
2013-12-20
11:34:04.345 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/705:desired
view is alert, size 1
2013-12-20
11:34:04.345 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/718:desired
view is same as the current view
2013-12-20
11:34:04.345 Lync[563:3a71018c] INFO UI CMNotificationManager.mm/480:reposition
floating views
2013-12-20
11:34:04.345 Lync[563:3a71018c] INFO UI CMAlertViewController.mm/110:showalert
is 1
2013-12-20
11:34:04.345 Lync[563:3a71018c] INFO UI CMAlertViewController.mm/114:showalert
is 0
2013-12-20
11:34:04.345 Lync[563:3a71018c] INFO UI CMUIUtil.mm/402:Mapping error code =
0x22020005, context = , type = 201
2013-12-20
11:34:04.346 Lync[563:3a71018c] INFO UI CMUIUtil.mm/1680:Mapped error message
is ‘Cannot connect to the server because it could be busy or temporarily
unavailable. Retry.’Hi Kent,
thanks a lot for your reply!
I created _sip._tls.domain-ext.com SRV record in the external DNS and now autodiscovery works fine. At the beginning I had not created it because I thought lyncdiscover.domain-ext.com A record was enough for autodiscovery. I still cannot understand
why lyncdiscover.domain-ext.com points to reverse proxy, while _sip._tls.domain-ext.com points to Edge server. It's strange because both are part of the research order of Lync 2013 desktop clients.
By the way, mobility still does not work. I tried to insert bot the https URLs as manual configuration but Lync 2013 for iPad was not be able to login. I tried to paste both the URLs in the web browser and:
with https://<ExtwebFQDN>/Autodiscover/autodiscoverservice.svc/Root appears the "Root.json" file to be downloaded;
with https://<IntwebFQDN>/AutoDiscover/AutoDiscover.svc/Root
the message "500-Internal error of server" appears.
Any suggests from you about how to check the configuration of ISS/ARR 2.5?
Thanks again! -
Lync 2013 and Dell Latitude 7240 Window 8.1 Problem! Please help SOS
Hi guys,
Can anyone know the solution for my current problem with Lync is frozen and crashes when I start my video call. I have brand new Dell Latitude 7240 with Window 8.1 and Lync 2013. I have tried so many different suggestion from different forums and update
my Lync as well. However, the problem is still there :(
I have been experiencing this problem for almost 2 months. It would be great to get my Lync works with video call. I tested the camera both internal and external camera as well. They works fine with Skype, ect...But not with Lync
Thanks in advance!!!HI
I have seen 100 % laptops of dell which has issue with Lync, I tried to raise this Dell as per them is issue with Lync and even Mircrosoft global team said it dell laptop drivers issue, Some of the cases has been resolved by uninstalling Audio/video
drivers. but not for every laptop.
Regards
zahoor -
Lync 2013 and lync 2011 for mac (can not complete the call)
hi everyone
A brand new Lync 2013 installed and updated.
We are testing it on our LAN enviroment (no firewall issues).Our windows clients can sign in and can work very well with all options (audio ,video,conference ).BUt our mac clients (macbook pro with lync 2011 14.0.8 140321 ) cant make audio call
or video call.when they try to make it , it gives the following generic error ,cannot complete the call.
I enabled lync 2011 logging ,but also can not find the related log file also on the macbook.
One more info ,on macbookpro when we use the lync web app ,and we can make video and audio calls.
I tried to uninstall lync 2011 from macbook ,reinstall ...not worked
After the install tried to update ,the lync 2011 client step by step to the latest version ,But all microsoft lync 2011 updates are at the moment are to the latest version (14.0.8)h
THi,
As the issue happen only for Lync Mac client, so it should be the of Lync Mac client.
You can try to perform a Clean Uninstall for Mac Lync client and then test again.
Here is a link below:
http://support.microsoft.com/kb/2691870
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
Lync 2013 and Raising Forest/Domain Functional Level?
My current forest and domain functional levels are 2008 R2. I know I can safely upgrade the functional levels in most cases, but I want to specifically know with regards to Lync.
Our entire environment, including Lync, is running on Windows Server 2012 R2. (We have no domain joined clients.) We are running Lync 2013 Standard with all the latest updates.
Can I safely raise the forest and domain functional levels to 2012 R2 without impacting Lync?Hi,
Yes, you can raise Forest and domain function level to Windows Server 2012 R2 without issue.
After raising Forest\domain function level, the new features that rely on the functional level are generally limited to AD itself. Regardless, changing the Domain or Forest Functional Level should have no impact on an application that depends on
Active Directory.
More details:
http://blogs.technet.com/b/askds/archive/2011/06/14/what-is-the-impact-of-upgrading-the-domain-or-forest-functional-level.aspx
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
Lync 2013 and Sametime Same Domain
Deploying Lync within my Org and unfortunate for us we use sametime.
If the Lync 2013 deployment resides in mycompany.com, and thus is the sip domain. The sametime domain is also mycompany.com as this is historic.
Are there any Gotchas or can these both interact as normal using the XMPP Gateway. If you think of it like
[email protected] on lync talking to
[email protected] on sametime, I just wondered if there was any conflicts,
Any documents on setup would also be cool.
thanksThey should be fine independent, but if both need to talk to public XMPP networks, you'll need to pick either Lync or SameTime due to the DNS records for _XMPP-Server._tcp.
If they need to communicate with eachother via XMPP, this would also be difficult because they have the same SIP domain, the routing wouldn't work. They wouldn't know to send the communications via XMPP if they have the same SIP domain.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications -
Lync 2013 and problem with copy/paste from SQL Mgmt Studio.
Hi Everyone,
Recently one of ours programmers noticed a very interesting issue which is a real pain in the a## for him and his colleagues. It was all fine with Lync client 2010, problem started when moved some people to 2013 client.
When someone sends him a message with SQL Code, and he is pasting it into SQL mgmt std. he gets dashes "-" instead of spaces " ".
I thought this is a local PC issue, but:
1. On 2010 it worked, stopped all of a sudden when they changed lync client to 2013
2. They are pasting code on the SERVER not local SQL mgmt std. on their client machines
3. Even if I send him a code from Lync 2010 and he is pasting that from his 2013 client - he gets "-" dashes, so I guess it is not important from where I send the message, but from where he is copying it.
As for now, I have noticed that problem with guys from England and region of APAC - they have lync 2013 client already.
Really appreciate any help as I donot have any point where to start troubleshooting...
Cheers guys,Hi,
I test the issue with my colleague and didn't find the same issue.
Here is the screenshot:
So please check if Lync Server 2013 and all the issued Lync 2013 client update to the latest version firstly, it not update to the latest version, update it and then test again.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support
Maybe you are looking for
-
How to get the last wbs which is displayed in transaction code cj03?
Dear Experts, I want to get the last wbs which are displayed in transaction code cj03, i have written below program,but i found it is incorrect. because the sort of wbs in cj03 is not equal to table prps. the last wbs in cj03 is not equal to ta
-
I cannot get into my iTunes store, I have an old windows PC that my iTunes is set up to. It keeps showing me a page with information on iTunes 10.3 every time I click on iTunes store & I cannot get rid of it. The links it gives me to download do not
-
there is a scenario in informatica..where we can select more than one rows and group by on only one row..its possible in informatica.. so can any one tell how to sql for those type of scenarios For example there are SEQUENCE_ID NUMBER NOT NULL, SAT_I
-
Any Spatial Method which can Insert Polygon Geometry in Table
Hi All, Is there any Method of Oracle Spatial which can insert a polygon plotted with polygon tool on the map directly into any database table or do we have to resort to get each of the co-ordinates from the map and create a procedure to insert the o
-
Problems with JSP-ApplicationModule pooling in runtime
Hello! I have an urgent Problem with the ApplicationModule Pooling in Runtime. The Application uses JSP with BC4J and is deployed on Tomcat 3.1 and MS IIS 4.0 (The Client want to use this MS-Product). We use JDev 3.1.1.2 for development. Now my Probl