Lync 2013 Setup and configure HELP
Hi,
i am having some trouble with my lync 2013 setup. i have configured lync to a stage were all users can connect to lync being inside or outside my network, we can send chats messages to each other but only if we are on the same LAN can we use the video, audio
and app sharing and desktop sharing. also i need to know how do i get my lync to communicate with other companies.
ok here is my setup.
ISP Cisco 877 router with 5 Static ips connects to my TMG 2010 (external Nic) internal nic connects to my LAN. all other devices plug into same LAN my TMG is forwarding ports to my exchange and helpdesk system. i have created all internal and external dns
entries. if i need an egde server were do i place this server.
network details below:
5 X ip: X.X.92.2
internal ip: X.X2.1 /24
please could someone assist me.
Kind Regards
Clemy
Cell : +27 72 864 0529
Hi There,
indeed your TMG Server should be equipped with 32 Network Interfaces as follows :
External
DMZ
Internal
the Lync Edge Server should be equipped with 2 Network Interfaces, usually the Edge server is placed inside a perimeter network which consists in 2 edge firewalls, one External and another one is Internal. please check the following link for detailed information
about the various Edge topology that are supported.
However you can always have a DMZ like your scenario which consists in a single firewall and connect the Edge server ends as follows
one interface to the TMG DMZ interface and one interface to the Internal Interface although this way you will be only protecting traffic from the DMZ interface.
kindly note that in case you chose to implement a secondary firewall take into consideration that the network relation from the the Edge internal interface to the internal LAN via the secondary firewall should be a route relation. since this is only the
supported scenario.
as for the reverse proxy you can still use the existing TMG as a reverse proxy since all published web components are actually located on the lync front-end server located on company LAN.
Regards,
Charbel Hanna
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread
Similar Messages
-
Visual Studio 2013 Setup and Installation gets stuck at system restore point. what are the issues?, help me out ASAP
Hello nitinrathod29,
There are some possible fixes for this issue.
Please check the following thread:
https://social.msdn.microsoft.com/Forums/vstudio/en-US/47bc6990-00f2-4d85-b3f8-9de03c637f43/visual-studio-2013-update-2rc-stucks-on-creating-system-restore?forum=vssetup
https://social.msdn.microsoft.com/Forums/vstudio/en-US/81478f51-37bb-4dbb-bd0c-beade1fd50ab/visual-studio-2012-professional-installation-getting-stuck-creating-a-system-restore-point?forum=vssetup
So here are them:
1. Check if you have any software which may prevent the installer from running. For example, Windows Defender or any other software which may restrict your permissions.
2. Just start the computer.
3. Run the setup as admin.
4. Check your UAC permissions.
Best regards,
Barry
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
Lync 2013 "Setup can't find or validate an installation file...."
Enterprise client installation.
We're running Windows 7 32bit SP2, Office 2010 32bit SP2.
Attempting to run the install for Lync 2013 (32-bit) on a test system and get the following warning immediately:
"Setup can't find or validate an installation file. Please try installing Office from your installation source, or if you installed from a downloaded package, please re-download and re-install....."
The source Lync 2013 file is direct from MVLS.
Any reason why this install from MVLS refuses to run from the source? Obviously, Lync 2013 wasn't included with Office 2010, so re-installing Office won't resolve this issue.
Any help is appreciated.Hi,
It may also cause by the issue of the conflict with other software, please use clean boot to test the issue. In this mode install Lync 2013 file again.
You can refer to the link of “How to perform a clean boot in Windows”:
http://support.microsoft.com/kb/929135
If the issue persists, please also try to download Lync 2013 file and install again.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
Hi,
Could someone help me in the setup and configuration of NI OPC server to OMRON PLC (CJ2H model) using FINS Ethernet communication protocol? I already read some materials available in the web but it uses a different PLC and communication protocol. The OPC server is installed in my laptop and I'm using Windows 8 as my OS. I used a cross over RJ45 LAN cable and connected to the ETN21 module of the PLC. I was able to confirmed the communication of my laptop and PLC by pinging the ip address of the ETN21. I also tried to configure the OPC server based on the documents I just read online. I created a channel, device and tag to the OPC server. By the way, I just need to read the data from the tag I created. Can someone also tell me how to monitor the data on the tag? I hope that you could help me. Thank you in advance.Good day,
Try following the instructions on the driver’s help, take a look at the attach picture. It should be a good starting point. After the PLC is configured you can use this tutorial (Connect LabVIEW to Any PLC Using OPC » http://www.ni.com/white-paper/7450/en/) for a guide on how to monitor the tags.
I hope this helps
Alejandro | Academic Program Engineer | National Instruments
Attachments:
OPC Server Help.JPG 237 KB -
How to Generate 250 Users Conference using Lync 2013 Stress and Performance Tool
How to Generate 250 Users N-way IM Conference using Lync 2013 Stress and Performance Tool.
Please Let know the configurations to generate the XMLs. We are not able to create more than 70 users N-way IM conference though during configuration, we opted for 300 users conference for Large Conference (in custom setting).
The tool somehow does not create the number of participants as indicated. Is there any way to troubleshoot why it's not generating the expected load.Hi,
Would you please elaborate more about your Lync environment?
Please check if you meet the following configuration requirements:
Set the MaxMeetingSize option to 1000. (The default is 250.)
Set the AllowLargeMeetings option to True.
Set the EnableAppDesktopSharing option to None.
Set the AllowUserToScheduleMeetingsWithAppSharing option to False.
Set the AllowSharedNotes option to False.
Set the AllowAnnotations option to False.
Set the DisablePowerPointAnnotations option to True.
Set the AllowMultiview option to False.
Set the EnableMultiviewJoin option to False.
More details:
http://technet.microsoft.com/en-us/library/jj205074.aspx
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support -
Lync 2013 Client and Outlook 2010
Hi, I installed Lync 2013 (FE and Edge server). I am able to talk but still I need to buy suitable certificate in order to access from outside. Rest of the network is as follow. SBS 2011 with exchange 2010, clients have Office 2010.
Problems that I noticed are:
- If in Calelendar there is appointment, Lync client shows still available
- Lync meeting button doesn't react when pressed.
Is Lync 2013 client backward compatible with older office/Exchange or not ?
For presence show doesn't integrate with outlook, Verify that the
Lync Meeting Add-in for Microsoft Office is installed and enabled in Microsoft Outlook.
For lync 2013 client compatible with office and Exchange, you can refer below link
http://technet.microsoft.com/en-us/library/gg412817.aspx
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical -
CONCURRENT MANAGER SETUP AND CONFIGURATION REQUIREMENTS IN AN 11I RAC ENVIR
제품 : AOL
작성날짜 : 2004-05-13
PURPOSE
RAC-PCP 구성에 대한 Setup 사항을 기술한 문서입니다.
PCP 구현은 CM의 workload 분산, Failover등을 목적으로 합니다.
Explanation
Failure sceniro 는 다음 3가지로 구분해 볼수 있습니다.
1. The database instance that supports the CP, Applications, and Middle-Tier
processes such as Forms, or iAS can fail.
2. The Database node server that supports the CP, Applications, and Middle-
Tier processes such as Forms, or iAS can fail.
3. The Applications/Middle-Tier server that supports the CP (and Applications)
base can fail.
아래부분은 CM,AP 구성과
CM과 GSM(Global Service Management)과의 관계를 설명하고 있습니다.
The concurrent processing tier can reside on either the Applications, Middle-
Tier, or Database Tier nodes. In a single tier configuration, non PCP
environment, a node failure will impact Concurrent Processing operations do to
any of these failure conditions. In a multi-node configuration the impact of
any these types of failures will be dependent upon what type of failure is
experienced, and how concurrent processing is distributed among the nodes in
the configuration. Parallel Concurrent Processing provides seamless failover
for a Concurrent Processing environment in the event that any of these types of
failures takes place.
In an Applications environment where the database tier utilizes Listener (
server) load balancing is implemented, and in a non-load balanced environment,
there are changes that must be made to the default configuration generated by
Autoconfig so that CP initialization, processing, and PCP functionality are
initiated properly on their respective/assigned nodes. These changes are
described in the next section - Concurrent Manager Setup and Configuration
Requirements in an 11i RAC Environment.
The current Concurrent Processing architecture with Global Service Management
consists of the following processes and communication model, where each process
is responsible for performing a specific set of routines and communicating with
parent and dependent processes.
아래 내용은 PCP환경에서 ICM, FNDSM, IM, Standard Manager의 역활을 설명하고
있습니다.
Internal Concurrent Manager (FNDLIBR process) - Communicates with the Service
Manager.
The Internal Concurrent Manager (ICM) starts, sets the number of active
processes, monitors, and terminates all other concurrent processes through
requests made to the Service Manager, including restarting any failed processes.
The ICM also starts and stops, and restarts the Service Manager for each node.
The ICM will perform process migration during an instance or node failure.
The ICM will be
active on a single node. This is also true in a PCP environment, where the ICM
will be active on at least one node at all times.
Service Manager (FNDSM process) - Communicates with the Internal Concurrent
Manager, Concurrent Manager, and non-Manager Service processes.
The Service Manager (SM) spawns, and terminates manager and service processes (
these could be Forms, or Apache Listeners, Metrics or Reports Server, and any
other process controlled through Generic Service Management). When the ICM
terminates the SM that
resides on the same node with the ICM will also terminate. The SM is ？hained?
to the ICM. The SM will only reinitialize after termination when there is a
function it needs to perform (start, or stop a process), so there may be
periods of time when the SM is not active, and this would be normal. All
processes initialized by the SM
inherit the same environment as the SM. The SM environment is set by APPSORA.
env file, and the gsmstart.sh script. The TWO_TASK used by the SM to connect
to a RAC instance must match the instance_name from GV$INSTANCE. The apps_<sid>
listener must be active on each CP node to support the SM connection to the
local instance. There
should be a Service Manager active on each node where a Concurrent or non-
Manager service process will reside.
Internal Monitor (FNDIMON process) - Communicates with the Internal Concurrent
Manager.
The Internal Monitor (IM) monitors the Internal Concurrent Manager, and
restarts any failed ICM on the local node. During a node failure in a PCP
environment the IM will restart the ICM on a surviving node (multiple ICM's may
be started on multiple nodes, but only the first ICM started will eventually
remain active, all others will gracefully terminate). There should be an
Internal Monitor defined on each node
where the ICM may migrate.
Standard Manager (FNDLIBR process) - Communicates with the Service Manager and
any client application process.
The Standard Manager is a worker process, that initiates, and executes client
requests on behalf of Applications batch, and OLTP clients.
Transaction Manager - Communicates with the Service Manager, and any user
process initiated on behalf of a Forms, or Standard Manager request. See Note:
240818.1 regarding Transaction Manager communication and setup requirements for
RAC.
Concurrent Manager Setup and Configuration Requirements in an 11i RAC
Environment
PCP를 사용하기위한 기본적인 Setup 절차를 설명하고 있습니다.
In order to set up Setup Parallel Concurrent Processing Using AutoConfig with
GSM,
follow the instructions in the 11.5.8 Oracle Applications System Administrators
Guide
under Implementing Parallel Concurrent Processing using the following steps:
1. Applications 11.5.8 and higher is configured to use GSM. Verify the
configuration on each node (see WebIV Note:165041.1).
2. On each cluster node edit the Applications Context file (<SID>.xml), that
resides in APPL_TOP/admin, to set the variable <APPLDCP oa_var="s_appldcp">
ON </APPLDCP>. It is normally set to OFF. This change should be performed
using the Context Editor.
3. Prior to regenerating the configuration, copy the existing tnsnames.ora,
listener.ora and sqlnet.ora files, where they exist, under the 8.0.6 and iAS
ORACLE_HOME locations on the each node to preserve the files (i.e./<some_
directory>/<SID>ora/$ORACLE_HOME/network/admin/<SID>/tnsnames.ora). If any of
the Applications startup scripts that reside in COMMON_TOP/admin/scripts/<SID>
have been modified also copy these to preserve the files.
4. Regenerate the configuration by running adautocfg.sh on each cluster node as
outlined in Note:165195.1.
5. After regenerating the configuration merge any changes back into the
tnsnames.ora, listener.ora and sqlnet.ora files in the network directories,
and the startup scripts in the COMMON_TOP/admin/scripts/<SID> directory.
Each nodes tnsnames.ora file must contain the aliases that exist on all
other nodes in the cluster. When merging tnsnames.ora files ensure that each
node contains all other nodes tnsnames.ora entries. This includes tns
entries for any Applications tier nodes where a concurrent request could be
initiated, or request output to be viewed.
6. In the tnsnames.ora file of each Concurrent Processing node ensure that
there is an alias that matches the instance name from GV$INSTANCE of each
Oracle instance on each RAC node in the cluster. This is required in order
for the SM to establish connectivity to the local node during startup. The
entry for the local node will be the entry that is used for the TWO_TASK in
APPSORA.env (also in the APPS<SID>_<HOSTNAME>.env file referenced in the
Applications Listener [APPS_<SID>] listener.ora file entry "envs='MYAPPSORA=<
some directory>/APPS<SID>_<HOSTNAME>.env)
on each node in the cluster (this is modified in step 12).
7. Verify that the FNDSM_<SID> entry has been added to the listener.ora file
under the 8.0.6 ORACLE_HOME/network/admin/<SID> directory. See WebiV Note:
165041.1 for instructions regarding configuring this entry. NOTE: With the
implementation of GSM the 8.0.6 Applications, and 9.2.0 Database listeners
must be active on all PCP nodes in the cluster during normal operations.
8. AutoConfig will update the database profiles and reset them for the node
from which it was last run. If necessary reset the database profiles back to
their original settings.
9. Ensure that the Applications Listener is active on each node in the cluster
where Concurrent, or Service processes will execute. On each node start the
database and Forms Server processes as required by the configuration that
has been implemented.
10. Navigate to Install > Nodes and ensure that each node is registered. Use
the node name as it appears when executing a nodename?from the Unix prompt on
the server. GSM will add the appropriate services for each node at startup.
11. Navigate to Concurrent > Manager > Define, and set up the primary and
secondary node names for all the concurrent managers according to the
desired configuration for each node workload. The Internal Concurrent
Manager should be defined on the primary PCP node only. When defining the
Internal Monitor for the secondary (target) node(s), make the primary node (
local node) assignment, and assign a secondary node designation to the
Internal Monitor, also assign a standard work shift with one process.
12. Prior to starting the Manager processes it is necessary to edit the APPSORA.
env file on each node in order to specify a TWO_TASK entry that contains
the INSTANCE_NAME parameter for the local nodes Oracle instance, in order
to bind each Manager to the local instance. This should be done regardless
of whether Listener load balancing is configured, as it will ensure the
configuration conforms to the required standards of having the TWO_TASK set
to the instance name of each node as specified in GV$INSTANCE. Start the
Concurrent Processes on their primary node(s). This is the environment
that the Service Manager passes on to each process that it initializes on
behalf of the Internal Concurrent Manager. Also make the same update to
the file referenced by the Applications Listener APPS_<SID> in the
listener.ora entry "envs='MYAPPSORA= <some directory>/APPS<SID>_<HOSTNAME>.
env" on each node.
13. Navigate to Concurrent > Manager > Administer and verify that the Service
Manager and Internal Monitor are activated on the secondary node, and any
other addititional nodes in the cluster. The Internal Monitor should not be
active on the primary cluster node.
14. Stop and restart the Concurrent Manager processes on their primary node(s),
and verify that the managers are starting on their appropriate nodes. On
the target (secondary) node in addition to any defined managers you will
see an FNDSM process (the Service Manager), along with the FNDIMON process (
Internal Monitor).
Reference Documents
Note 241370.1What is your database version? OS?
We are using VCP suite for Planning Purpose. We are using VCP environment (12.1.3) in Decentralized structure connecting to 3 differect source environment ( consisting 11i and R12). As per the Oracle Note {RAC Configuration Setup For Running MRP Planning, APS Planning, and Data Collection Processes [ID 279156]} we have implemented RAC in our test environment to get better performance.
But after doing all the setups and concurrent programs assignment to different nodes, we are seeing huge performance issue. The Complete Collection which takes generally on an avg 180 mins in Production, is taking more than 6 hours to complete in RAC.
So I would like to get suggestion from this forum, if anyone has implemented RAC in pure VCP (decentralized) environment ? Will there be any improvement if we make our VCP Instance in RAC ?Do you PCP enabled? Can you reproduce the issue when you stop the CM?
Have you reviewed these docs?
Value Chain Planning - VCP - Implementation Notes & White Papers [ID 280052.1]
Concurrent Processing - How To Ensure Load Balancing Of Concurrent Manager Processes In PCP-RAC Configuration [ID 762024.1]
How to Setup and Run Data Collections [ID 145419.1]
12.x - Latest Patches and Installation Requirements for Value Chain Planning (aka APS Advanced Planning & Scheduling) [ID 746824.1]
APSCHECK.sql Provides Information Needed for Diagnosing VCP and GOP Applications Issues [ID 246150.1]
Thanks,
Hussein -
Difference between 'setup' and 'configuration' in Oracle Apps
Hi,
Thank in advance.
I want to know Difference between 'setup' and 'configuration'(Oracle Apps ). Could you provide the details with an example, please?
Regards,
Raghavendra RaoBusiness Requirement:-
===============
A company may want to allow all of its employees to make purchases up to $10 without having such purchases approved. Another company may have a business rule that each employee’s approval limit depends on his or her position within the organization.
Question:-
=======
How to reach the above requirement?
Is it thorugh configuration or setup?
It must be through configuration and not set up.
Set up is something like one time.. Configuration can be changed depends on your business needs.
Like if your company wants to increases the limit from 10 to 100$, then change in configuration is needed.
Hope you got the answer.. if you want more explanation, please be specific.... -
Setup and Configure IM Components SSO and DAS on Replica RMS Node
Dear All,
I was trying the step
Step 5: How to Setup and Configure IM Components SSO and DAS on Replica RMS Node In Multimaster Replication (MMR) with Identity Management (IM) Cluster in High Availability Env
But, at the stage to connect to OID, it is not connecting to the RMS database.
When I checked login through ODM, it is connecting fine. also, ldapbind is also binding fine.
How to solve this ? What will be the issue and where to check it ?
Also, from the RMS, when I am connecting through EM console, I am not getting any output on Infrastructure link to change the passwords. its showing
Identity Management
Error retrieving information of default metadata repository.
Unable to establish secure connection to Oracle Internet Directory Server ldap://devportal.paaf.gov.kw:636/ Base Exception : javax.naming.AuthenticationException: [LDAP: error code 49 - Invalid Credentials]
If there is any experts, pls reply. Because, last time I created a TAR and it took months to resolve and ultimately nothing happened they closed the TAR after some time as I was busy with some other works and not able to proceed with the synchronization.
Thanks in advance,
With Regards,
Sheeja AnilRule [ 47 ]: fuser link
~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the fuser symbolic link /sbin/fuser -> /bin/fuser exists or
not. This is required for Suse 8.0 and Suse 9.0.
Test [ PASSED ] :
Not required =~ Exists|Not required
Action:
fuser link exists or not required.
Rule [ 48 ]: orarun package
~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the orarun package is installed and if the oracle user
environment need to be reset. This is only required for Suse 8.0 and
Suse 9.0.
Test [ PASSED ] :
Not applicable =~ Not installed|Installed correctly|Not
applicable|Environment reset not required
Action:
orarun is not installed or installed correctly.
Rule [ 49 ]: semmsl
~~~~~~~~~~~~~~~~~~~
Description:
Check if semmsl kernel parameter is 256 or higher. For more details on
how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semmsl kernel parameter is 256 or higher.
Rule [ 50 ]: semmns
~~~~~~~~~~~~~~~~~~~
Description:
Check if semmns kernel parameter is 32000 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semmns kernel parameter is 32000 or higher.
Rule [ 51 ]: semopm
~~~~~~~~~~~~~~~~~~~
Description:
Check if semopm kernel parameter is 100 or higher. For more details on
how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semopm kernel parameter is 100 or higher.
Rule [ 52 ]: semmni
~~~~~~~~~~~~~~~~~~~
Description:
Check if semmni kernel parameter is 142 or higher. For more details on
how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
semmni kernel parameter is 142 or higher.
Rule [ 53 ]: shmall
~~~~~~~~~~~~~~~~~~~
Description:
Check if shmall kernel parameter is 2097152 or higher. For more
details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
shmall kernel parameter is 2097152 or higher.
Rule [ 54 ]: shmmax
~~~~~~~~~~~~~~~~~~~
Description:
Check if shmmax kernel parameter is 2147483648 or higher. For more
details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
shmmax kernel parameter is 2147483648 or higher.
Rule [ 55 ]: shmmni
~~~~~~~~~~~~~~~~~~~
Description:
Check if shmmni kernel parameter is 4096 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
shmmni kernel parameter is 4096 or higher.
Rule [ 56 ]: msgmax
~~~~~~~~~~~~~~~~~~~
Description:
Check if msgmax kernel parameter is 8192 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
msgmax kernel parameter is 8192 or higher.
Rule [ 57 ]: msgmnb
~~~~~~~~~~~~~~~~~~~
Description:
Check if msgmnb kernel parameter is 65535 or higher. Refer to Oracle
Application Server 10g Installation Guide 10g - Chapter 4 - Section
4.3.3 Configuring the Kernel Parameters on Linux for more details on
how to configure this.
Test [ PASSED ] :
Adequate = Adequate
Action:
msgmnb kernel parameter is 65535 or higher.
Rule [ 58 ]: msgmni
~~~~~~~~~~~~~~~~~~~
Description:
Check if msgmni kernel parameter is 2878 or higher. For more details
on how to configure this parameter, refer to Oracle Application Server
10.1.2 Installation Guide - Chapter 4 - Section 4.3.2 Configuring the
Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
msgmni kernel parameter is 2878 or higher.
Rule [ 59 ]: file-max
~~~~~~~~~~~~~~~~~~~~~
Description:
Check if file-max kernel parameter is 131072 or higher. For more
details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
file-max kernel parameter is 131072 or higher.
Rule [ 60 ]: ip_local_port_range
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if ip_local_port_range kernel parameter is between 10000 and
65000 or higher. For more details on how to configure this parameter,
refer to Oracle Application Server 10.1.2 Installation Guide - Chapter
4 - Section 4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
ip_local_port_range kernel parameter is between 10000 and 65000 or
higher.
Rule [ 61 ]: limit processes
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the limit of max processes is set to 16384 or higher. For
more details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
The limit of max processes is set to 16384 or higher.
Rule [ 62 ]: limit descriptors
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the limit of file descriptors is set to 65536 or higher. For
more details on how to configure this parameter, refer to Oracle
Application Server 10.1.2 Installation Guide - Chapter 4 - Section
4.3.2 Configuring the Kernel Parameters on Linux.
Test [ PASSED ] :
Adequate = Adequate
Action:
The limit of descriptors is set to 65536 or higher.
Rule [ 63 ]: Port 1521
~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if port 1521 is free or not. If port 1521 is used by an Oracle
listener version 10.1.0.2 or later, then the existing listener will be
used by the existing database and the Oracle Application Server 10g
Metadata Repository. The installer will perform this configuration
automatically. If port 1521 is used by an Oracle listener version
earlier than 10.1.0.2, then the existing listener need to be stopped.
After the installation is complete, the new 10.1.0.2 listener can be
configured to listen to the existing (pre 10.1.0.2) databases. If port
1521 is used by non-oracle programs, then this program need to be
configured to listen to ports other than 1521. Refer to Installation
Guide, section 4.4.4 for more details.
Test [ PASSED ] :
TNS Listener 10.1.0.2 or higher is running =~ TNS Listener 10.1.0.2 or
higher is running|Free
Action:
Port 1521 is not used, or is used by TNS*Listener version 9.0.1 or
higher.
Rule [ 64 ]: Environment Variables
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the following environment variables are not set: TNS_ADMIN,
ORA_NLS, and LD_BIND_NOW. In addition, the following environment
variables must not references to any existing Oracle Home: PATH,
CLASSPATH and LD_LIBRARY_PATH.
Test [ FAILED ] :
Has reference to existing Oracle Homes = Properly defined
Action:
Refer to the following table for the necessary action to take:
<PRE>
Return Value Action
Has reference to existing Remove any reference to existing
Oracle Homes Oracle Homes from PATH, CLASSPATH
and LD_LIBRARY_PATH.
Some variables are set Unset TNS_ADMIN, ORA_NLS, and
LD_BIND_NOW.
Cannot access /etc/oratab Grant read permission on
/etc/issue to the current user.
</PRE>
Rule [ 67 ]: DNS Lookup
~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the host is properly registered in the DNS.
Test [ FAILED ] :
nslookup IP_address = Host correctly registered in DNS
Action:
Refer to the following table for the necessary action to take:
<PRE>
Return Value Action
nslookup host.domain The DNS server failed to resolve the
nslookup using host.domain.
nslookup IP_address The DNS server failed to resolve the
nslookup using IP address.
Cannot determine IP address Fix any problem with host IP address.
Cannot access Grant execute permission on
/usr/bin/nslookup /usr/bin/nslookup to the current
user.
</PRE>
Rule [ 68 ]: /etc/hosts format
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if /etc/hosts file contains a line with "ip_address
fully_qualified_hostname short_hostname".
Test [ PASSED ] :
Contains host.domain = Contains host.domain
Action:
The Fuly Qualified Domain name has been set correctly.
Rule [ 69 ]: Oracle Home length
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check that the path to the Oracle home directory is not longer than
127 characters.
Test [ PASSED ] :
Less than 127 char = Less than 127 char
Action:
Oracle Home directory is not longer than 127 characters.
Rule [ 70 ]: Memory for Dev Kit
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the machine has enough memory to install Developer Kits
install type. The minimum requirements is 256 MB.
Test [ PASSED ] :
Available = Available
Action:
The machine has enough memory to install J2EE & Webcache install type.
Rule [ 71 ]: Memory for BI&Forms
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the machine has enough memory to install Business
Intelligence & Forms install type. The minimum requirements is 1 GB.
Test [ PASSED ] :
Available =~ Available|Install type not available
Action:
The machine has enough memory to install Business Intelligence & Forms
install type.
Rule [ 72 ]: Space for BI&Forms
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the machine has enough disk space to install Business
Intelligence & Forms install type. The minimum requirements is 2 GB.
Test [ PASSED ] :
Available =~ Available|Install type not available
Action:
The machine has enough disk space to install Business Intelligence &
Forms install type.
Rule [ 73 ]: control-center
~~~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the minimum required control-center package version is
installed. For RedHat AS/ES 4.0: control-center-2.8.0-12.
Test [ PASSED ] :
Adequate =~ Adequate|Not required
Action:
The required compat-db package version or higher is installed.
Rule [ 74 ]: xscreensaver
~~~~~~~~~~~~~~~~~~~~~~~~~
Description:
Check if the minimum required xscreensaver package version is
installed. For RedHat AS/ES 4.0: xscreensaver-4.18-5.rhel4.2.
Test [ PASSED ] :
Adequate =~ Adequate|Not required
Action:
The required compat-db package version or higher is installed. -
Setup and configuration for system monitoring and IT Reporting for Java sys
Hi all,
How to setup and configuration for system monitoring and IT Reporting for Java system ?
How to connect Java system to Solman system?
Regards,
NeniHI,
What is your OS? You can use SAPCCMSR.exe to monitoring IT Reporting Java system on Solman.
Go to solman rz21 create a csmreg user. and configuration fil for agent. copy configuration fil on usr/sap/ccms/..
Go to comman line cd ../user/sap/xxx/sys/exe/.../ wite SAPCCMSR.00 -R pf=< ...../sys/profile/instans profile> .
You can se agent on rz10 and use this connaction on rz20 to monitoring and IT Reporting Java system on Solman.
I hope this help -
Dear All Hello,
i am having one very strange issue, I setup lync 2013 certficate all thing okay. We can login into lync 2013 client to lync 2013 server without any issue using PC but same login if i try to login into mobile having anrorid or windows phone it fais and its
pop up message we cannot sign you in please check your account info and try again.
We just created user using Enterprise voice optin, checked mobility is enabled. External url is configured.
Any body can refer if something is missing. I havenot updated any cu for lync 2013.
If i run Test-CsUcwaConference or Test-CsMcxP2PIM for mobiliity i get following error. I havneot done any update nor any tool as most of article are refering for lync 2010.
No response received for Web-Ticket service.
Inner Exception:The content type text/html; charset=utf
the response message does not match the content type of
binding (text/xml; charset=utf-8). If using a custom en
be sure that the IsContentTypeSupported method is imple
properly. The first 1024 bytes of the response were:
'<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//E
"http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<title>IIS 8.5 Detailed Error - 500.0 - Internal Server
Error</title>
<style type="text/css">
<!--
body{margin:0;font-size:.7em;font-family:Verdana,Arial,
a,sans-serif;}
code{margin:0;color:#006600;font-size:1.1em;font-weight
.config_source code{font-size:.8em;color:#000000;}
pre{margin:0;font-size:1.4em;word-wrap:break-word;}
ul,ol{margin:10px 0 10px 5px;}
ul.first,ol.first{margin-top:5px;}
fieldset{padding:0 15px 10px 15px;word-break:break-all;
.summary-container
fieldset{padding-bottom:5px;margin-top:4px;}
legend.no-expand-all{padding:2px 15px 4px 10px;margin:0
-12px;}
legend{color:#333333;;margin:4px 0 8px -12px;_margin-to
font-weight:bold;font-size:1em;}
a:link,a:visited{color:#007EFF;font-weight:bold;}
a:hover{text-decoration:none;}
h1{font-size:2.4em;margin:0;color:#FFF;}
h2{font-size:1.7em;margin:0;'.
Inner Exception:The remote server returned an error: (5
Internal Server Error.Let ensure the mobile client can connect fine
http://blogs.technet.com/b/nexthop/archive/2012/02/21/troubleshooting-external-lync-mobility-connectivity-issues-step-by-step.aspx
Also we can use the Lync connection analyzer tool for Mobile scenario and test
http://blogs.technet.com/b/nexthop/archive/2013/02/08/the-new-lync-connectivity-analyzer.aspx
Please remember, if you see a post that helped you please click ;Vote As Helpful" and if it answered your question please click "Mark As Answer" Regards Edwin Anthony Joseph
Great follow up thanks!.
Seems i am near to solution.
I used web site url https://testconnectivity.microsoft.com it pass all test,
When i use to test using tool it goes to my local fqdn and says unable to resolve.
An error occurred while sending the request.
The remote name could not be resolved: 'lync1.hosting.mydomain.local'
When i open this url lyncdiscover_contoso.com it give both internal and extral url.
Which is this {"_links":{"self":{"href":"https://lync1.hosting.mydomain.local/Autodiscover/AutodiscoverService.svc/root?originalDomain=haxxess.com"},"user":{"href":"https://lync01.externaldomain.com/Autodiscover/AutodiscoverService.svc/root/oauth/user?originalDomain=external.com"},"xframe":{"href":"https://lync01.externaldomain.com/Autodiscover/XFrame/XFrame.html"}}}
I am using lync 2013, with no tmg for publishing, internal web servie name is empty overrite and extranal is lync01.externaldomain.com
So as article says if i see internal url If the internal web services URL is identified, the web publishing rule is incorrect and is bridging the connection to port 443
instead of port 4443 for the Lync external web services.
Where do i have to change this in topology under web service. can you please guide this last phase. -
Lync 2013 installation and problems
I have gone through the entire setup and have a somewhat working installation. Now my problem is that when I sign in two users to the Lync 2013 Basic, they log in fine but it doesn't show any users online.
when I add a contact from my organization, it does match any of the test users that I have setup
Not sure what to check to find out where the issue isWhen you say they log in fine, but it doesn't show any users online, do the two Lync basic users see each other's presence?
What do you see when you add a contact from your organization? Are the test users you created not in the list? For this I'd suggest running update-csaddressbook from PowerShell on the Lync server, wait 5 minutes, exit Lync (not just sign out,
make sure you've fully exited) and trash the profile by deleting the %userprofile%\appdata\Local\Microsoft\Office\15.0\Lync\[email protected] folder.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications -
Lync 2013 mobility and external access not working
Hi all.
I installed and configured Lync Server 2013 Front End and Lync Server 2013 Edge on Windows Server 2012 R2.
Internal lync clients (not mobile) can successfully connect to server and everything works fine for them. External users can connect only with manual configuration of address of external lync server in lync client, autodiscovery doesn't work.
I also installed and configured IIS ARR Reverse Proxy on Windows Server 2012 R2 using this article -
http://blogs.technet.com/b/nexthop/archive/2013/02/19/using-iis-arr-as-a-reverse-proxy-for-lync-server-2013.aspx. But it doesn't work too. When I try to connect I get 'Unable to connect to the server. Check your network connection or the server address and
try again'.
I configured dns records in the external dns zone.
For Edge:
sip.extdomain.ru – IP1
lyncwebconf.extdomain.ru – IP2
lyncav.extdomain.ru – IP3
For Reverse Proxy:
lyncdialin.extdomain.ru - IP4
lyncmeet.extdomain.ru - IP4
lyncextweb.extdomain.ru - IP4
lyncdiscover.extdomain.ru - IP4
I issued all needed certificates by the internal CA and added following alternative names.
For FE certificate:
sip.cherry.loc
lync.cherry.loc
dialin.cherry.loc
meet.cherry.loc
admin.cherry.loc
lyncdiscoverinternal.cherry.loc
lyncdiscover.cherry.loc
lyncdialin.extdomain.ru
lyncmeet.extdomain.ru
lyncextweb.extdomain.ru
lyncdiscover.extdomain.ru
For Edge external and Reverse Proxy:
lyncav.extdomain.ru
sip.extdomain.ru
lyncwebconf.extdomain.ru
lyncdialin.extdomain.ru
lyncmeet.extdomain.ru
lyncextweb.extdomain.ru
lyncdiscover.extdomain.ru
cherry.loc
The root certificate of internal CA installed on all servers and client devices.
Using Wireshark I see that Reverse Proxy communicating with FE on port 4443.
Here is an excerpt from mobile client log.
GET https://lyncdiscover.extdomain.ru/?sipuri=sip:[email protected]
Request Id: 0x6f54648
HttpHeader:Cache-Control no-cache
HttpHeader:Content-Length 1006
HttpHeader:Content-Type application/vnd.microsoft.rtc.autodiscover+xml; v=1
HttpHeader:Date Mon, 22 Sep 2014 11:17:45 GMT
HttpHeader:Expires -1
HttpHeader:Pragma no-cache
HttpHeader:Server Microsoft-IIS/8.5
HttpHeader:StatusCode 200
HttpHeader:X-AspNet-Version 4.0.30319
HttpHeader:X-Content-Type-Options nosniff
HttpHeader:X-MS-Server-Fqdn lync.cherry.loc
HttpHeader:X-Powered-By ASP.NET, ARR/2.5
Ôªø<?xml version="1.0" encoding="utf-8"?><AutodiscoverResponse xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-
instance" AccessLocation="External"><Root><Link token="Domain" href="https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/domain?originalDomain=extdomain.ru" /><Link token="User" href="https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru"
/><Link token="Self" href="https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root?originalDomain=extdomain.ru" /><Link token="OAuth"
href="https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/oauth/user?originalDomain=extdomain.ru" /><Link token="External/XFrame" href="https://lync.cherry.loc/Autodiscover/XFrame/XFrame.html" /><Link
token="Internal/XFrame" href="https://lync.cherry.loc/Autodiscover/XFrame/XFrame.html"
/><Link token="XFrame" href="https://lync.cherry.loc/Autodiscover/XFrame/XFrame.html" /></Root></AutodiscoverResponse>
</ReceivedResponse>
2014-09-22 15:17:53.041 Lync[299:715a000] INFO TRANSPORT CUcwaAutoDiscoveryResponse.cpp/119:location value is external
2014-09-22 15:17:53.042 Lync[299:715a000] INFO TRANSPORT CUcwaAutoDiscoveryResponse.cpp/195:User url is
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
2014-09-22 15:17:53.042 Lync[299:715a000] INFO TRANSPORT CHttpRequestProcessor.cpp/266:Sending event to main thread for request(0x6f54648)
2014-09-22 15:17:53.042 Lync[299:3c2a218c] INFO APPLICATION CTransportRequestRetrialQueue.cpp/822:Req. completed, Stopping timer.
2014-09-22 15:17:53.043 Lync[299:3c2a218c] INFO APPLICATION CUcwaAutoDiscoveryGetUserUrlOperation.cpp/290:Received a root response
2014-09-22 15:17:53.043 Lync[299:3c2a218c] INFO APPLICATION CUcwaAutoDiscoveryGetUserUrlOperation.cpp/224:UcwaAutoDiscoveryGetUserUrlOperation completed with
url = https://lyncdiscover.extdomain.ru/?sipuri=sip:[email protected], userUrl = https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru, status = S_OK (S0-0-0)
2014-09-22 15:17:53.043 Lync[299:3c2a218c] INFO APPLICATION CTransportRequestRetrialQueue.cpp/725:Response received for req. GET-UnAuthenticatedGet(0x6f54648): S_OK (S0-0-0) (Success); Done with req.; Stopping resend timer
2014-09-22 15:17:53.044 Lync[299:3c2a218c] INFO TRANSPORT CCredentialManager.cpp/176:getSpecificCredential for serviceId(1) returning: credType (1) signInName ([email protected]) domain (cherry) username (user) password.empty() (0) certificate.isValid() (0)
privateKey.empty() (1) compatibleServiceIds(1)
2014-09-22 15:17:53.044 Lync[299:3c2a218c] INFO TRANSPORT CMetaDataManager.cpp/403:Received a request to get the meta data of type 0 for url
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
2014-09-22 15:17:53.044 Lync[299:3c2a218c] INFO TRANSPORT CMetaDataManager.cpp/458:Sending Unauthenticated get to get the web-ticket url
2014-09-22 15:17:53.044 Lync[299:3c2a218c] INFO TRANSPORT CTransportThread.cpp/135:Added Request() to Request Processor queue
2014-09-22 15:17:53.045 Lync[299:3c2a218c] INFO TRANSPORT CAuthenticationResolver.cpp/109:Waiting on Meta Data from https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
2014-09-22 15:17:53.045 Lync[299:659a000] INFO TRANSPORT CTransportThread.cpp/347:Sent Request() to Request Processor
2014-09-22 15:17:53.045 Lync[299:3c2a218c] INFO APPLICATION CTransportRequestRetrialQueue.cpp/385:Submitting new req. GET-AuthenticatedUserGetRequest(0x6e83da8)
2014-09-22 15:17:53.045 Lync[299:659a000] WARNING TRANSPORT CCredentialManager.cpp/317:CCredentialManager::getSpecificCredential returning NULL credential
for serviceId (4) type (1)!
2014-09-22 15:17:53.046 Lync[299:3c2a218c] INFO APPLICATION CUcwaAutoDiscoveryService.cpp/1263:Submitting Authenticated AutoDiscovery request to
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
2014-09-22 15:17:53.046 Lync[299:659a000] INFO TRANSPORT TransportUtilityFunctions.cpp/689:<SentRequest>
GET https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
Request Id: 0x133b6a8
HttpHeader:Accept
</SentRequest>
2014-09-22 15:17:53.046 Lync[299:659a000] INFO UTILITIES CHttpStreamPool.cpp/399:Allocating stream 0x6e73850 for url - https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user with persistent id as 16
2014-09-22 15:17:53.047 Lync[299:659a000] VERBOSE TRANSPORT CHttpProxyHelper.cpp/435:CHttpProxyHelper::discoverProxy : No proxy found for url
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru. Sending over direct connection.
2014-09-22 15:17:53.050 Lync[299:659a000] ERROR TRANSPORT CHttpConnection.cpp/1029:Request Type = 0x%u0x6e743a0 Error domain = kCFErrorDomainCFNetwork code = 0x2 ErrorDescription = The operation couldn’t be completed. (kCFErrorDomainCFNetwork error 2.) ErrorFailureReason
= ErrorRecoverySuggestion =
2014-09-22 15:17:53.050 Lync[299:659a000] ERROR UTILITIES CHttpConnection.cpp/958:GetAddrInfo returned error 0x8
2014-09-22 15:17:53.050 Lync[299:659a000] INFO UTILITIES CHttpStreamPool.cpp/467:Releasing stream 0x6e73850.
2014-09-22 15:17:53.050 Lync[299:659a000] INFO UTILITIES CHttpStreamPool.cpp/599:Releasing stream 0x6e73850.
2014-09-22 15:17:53.051 Lync[299:659a000] INFO TRANSPORT CHttpRequestProcessor.cpp/173:Received response of request() with status = 0x22020001
2014-09-22 15:17:53.051 Lync[299:659a000] INFO TRANSPORT CHttpRequestProcessor.cpp/201:Request resulted in E_ConnectionError (E2-2-1). The retry counter is: 0
2014-09-22 15:17:53.051 Lync[299:659a000] WARNING TRANSPORT CCredentialManager.cpp/317:CCredentialManager::getSpecificCredential returning NULL credential
for serviceId (4) type (1)!
2014-09-22 15:17:53.052 Lync[299:659a000] INFO TRANSPORT TransportUtilityFunctions.cpp/689:<SentRequest>
GET https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
Request Id: 0x133b6a8
HttpHeader:Accept
</SentRequest>
2014-09-22 15:17:53.052 Lync[299:659a000] INFO UTILITIES CHttpStreamPool.cpp/399:Allocating stream 0x14102a0 for url - https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user with persistent id as 16
2014-09-22 15:17:53.053 Lync[299:659a000] VERBOSE TRANSPORT CHttpProxyHelper.cpp/435:CHttpProxyHelper::discoverProxy : No proxy found for url
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru. Sending over direct connection.
2014-09-22 15:17:53.056 Lync[299:659a000] ERROR TRANSPORT CHttpConnection.cpp/1029:Request Type = 0x%u0x14080f0 Error domain = kCFErrorDomainCFNetwork code =
0x2 ErrorDescription = The operation couldn’t be completed. (kCFErrorDomainCFNetwork error 2.) ErrorFailureReason = ErrorRecoverySuggestion =
2014-09-22 15:17:53.056 Lync[299:659a000] ERROR UTILITIES CHttpConnection.cpp/958:GetAddrInfo returned error 0x8
2014-09-22 15:17:53.056 Lync[299:659a000] INFO UTILITIES CHttpStreamPool.cpp/467:Releasing stream 0x14102a0.
2014-09-22 15:17:53.056 Lync[299:659a000] INFO UTILITIES CHttpStreamPool.cpp/599:Releasing stream 0x14102a0.
2014-09-22 15:17:53.057 Lync[299:659a000] INFO TRANSPORT CHttpRequestProcessor.cpp/173:Received response of request() with status = 0x22020001
2014-09-22 15:17:53.057 Lync[299:659a000] INFO TRANSPORT CHttpRequestProcessor.cpp/201:Request resulted in E_ConnectionError (E2-2-1). The retry counter is: 1
2014-09-22 15:17:53.057 Lync[299:659a000] INFO TRANSPORT CHttpRequestProcessor.cpp/266:Sending event to main thread for request(0x133b6a8)
2014-09-22 15:17:53.058 Lync[299:3c2a218c] INFO TRANSPORT CMetaDataManager.cpp/572:Received response for meta data request of type 60 with status 570556417
2014-09-22 15:17:53.058 Lync[299:3c2a218c] ERROR TRANSPORT CMetaDataManager.cpp/588:Unable to get a response to an unauthenticated get to url
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
2014-09-22 15:17:53.059 Lync[299:3c2a218c] INFO TRANSPORT CAuthenticationResolver.cpp/208:MetaData retrieval for url https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru completed with status 570556417
2014-09-22 15:17:53.059 Lync[299:3c2a218c] INFO TRANSPORT CAuthenticationResolver.cpp/238:Deleting 1 pended Meta data requests for url
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
2014-09-22 15:17:53.059 Lync[299:3c2a218c] ERROR TRANSPORT CAuthenticationResolver.cpp/334:Unable to get the meta data for server url
https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root/user?originalDomain=extdomain.ru
2014-09-22 15:17:53.059 Lync[299:3c2a218c] INFO TRANSPORT CAuthenticationResolver.cpp/337:Failing request to the request manager
2014-09-22 15:17:53.060 Lync[299:3c2a218c] INFO TRANSPORT CRequestManager.cpp/284:Failing secure request UcwaAutoDiscoveryRequest with status E_ConnectionError (E2-2-1)
2014-09-22 15:17:53.060 Lync[299:3c2a218c] INFO APPLICATION CTransportRequestRetrialQueue.cpp/822:Req. completed, Stopping timer.
2014-09-22 15:17:53.060 Lync[299:3c2a218c] INFO APPLICATION CUcwaAutoDiscoveryService.cpp/1358:Received autodiscovery response with status E_ConnectionError (E2-2-1)
2014-09-22 15:17:53.060 Lync[299:3c2a218c] INFO APPLICATION CUcwaAutoDiscoveryService.cpp/1316:Raising Autodiscovery event with status E_ConnectionError (E2-2-1) for eventType 0
2014-09-22 15:17:53.061 Lync[299:3c2a218c] INFO APPLICATION CUcwaAutoDiscoveryServiceRetrialWrapper.cpp/417:Received event for type 0 with status E_ConnectionError (E2-2-1)
2014-09-22 15:17:53.061 Lync[299:3c2a218c] INFO APPLICATION CUcwaAutoDiscoveryServiceRetrialWrapper.cpp/539:Autodiscovery scheduled retrial timer. Timer 0.000000 seconds
2014-09-22 15:17:53.061 Lync[299:3c2a218c] INFO APPLICATION CAlertReporter.cpp/64:Alert received! Category 1, Type 201, level 0, error E_ConnectionError (E2-2-1), context '', hasAction=false
2014-09-22 15:17:53.061 Lync[299:3c2a218c] INFO APPLICATION CAlertReporter.cpp/117:Alert cleared of Category 1, Type 201, cleared 0 alerts
2014-09-22 15:17:53.062 Lync[299:3c2a218c] INFO APPLICATION CTransportRequestRetrialQueue.cpp/725:Response received for req. GET-AuthenticatedUserGetRequest (0x6e83da8): E_ConnectionError (E2-2-1) (RemoteNetworkTemporaryError); Done with req.; Stopping resend
timer
2014-09-22 15:17:53.062 Lync[299:3c2a218c] INFO UI CMAlertViewController.mm/87:ObservableListItem Added event received
2014-09-22 15:17:53.062 Lync[299:3c2a218c] INFO UI CMAlertViewController.mm/97:showalert is 1
2014-09-22 15:17:53.063 Lync[299:3c2a218c] INFO UI CMConversationCommon.mm/43:not signed in
2014-09-22 15:17:53.063 Lync[299:3c2a218c] INFO UI CMConversationCommon.mm/43:not signed in
2014-09-22 15:17:53.063 Lync[299:3c2a218c] INFO UI CMConversationCommon.mm/43:not signed in
2014-09-22 15:17:53.063 Lync[299:3c2a218c] INFO UI CMConversationCommon.mm/43:not signed in
2014-09-22 15:17:53.063 Lync[299:3c2a218c] INFO UI CMConversationCommon.mm/43:not signed in
2014-09-22 15:17:53.064 Lync[299:3c2a218c] INFO UI CMNotificationManager.mm/697:desired view is alert, size 1
2014-09-22 15:17:53.064 Lync[299:3c2a218c] INFO UI CMNotificationManager.mm/737:adding the desired view
2014-09-22 15:17:53.065 Lync[299:3c2a218c] INFO UI CMNotificationManager.mm/472:reposition floating views
2014-09-22 15:17:53.065 Lync[299:3c2a218c] INFO UI CMAlertViewController.mm/104:showalert is 1
2014-09-22 15:17:53.065 Lync[299:3c2a218c] INFO UI CMAlertViewController.mm/108:showalert is 0
2014-09-22 15:17:53.066 Lync[299:3c2a218c] INFO UI CMUIUtil.mm/410:Mapping error code = 0x22020001, context = , type = 201
2014-09-22 15:17:53.066 Lync[299:3c2a218c] INFO UI CMUIUtil.mm/1708:Mapped error message is 'Unable to connect to the server. Check your network connection or the server address and try again.Result of Lync Connectivity Analyzer.
External Auto discover service : https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root
Starting Lync server autodiscovery
Please wait; this test may take several minutes to complete...
Starting automatic discovery for secure (HTTPS) internal channel
lyncdiscoverinternal.extdomain.ru can't be resolved by the DNS server. Skipping internal discovery.
Starting automatic discovery for secure (HTTPS) external channel
Server discovery has completed for https://lyncdiscover.extdomain.ru/.
Automatic discovery results for https://lyncdiscover.extdomain.ru/
Access Location : Internal
SIP Server Internal Access : lync.cherry.loc
SIP Server External Access : sip.extdomain.ru
SIP Client Internal Access : lync.cherry.loc
SIP Client External Access : sip.extdomain.ru
Internal Auth broker service : https://lync.cherry.loc/Reach/sip.svc
External Auth broker service : https://lync.cherry.loc/Reach/sip.svc
Internal Auto discover service : https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root
External Auto discover service : https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root
Internal MCX service : https://lync.cherry.loc/Mcx/McxService.svc
External MCX service : https://lync.cherry.loc/Mcx/McxService.svc
Internal UCWA service : https://lync.cherry.loc/ucwa/v1/applications
External UCWA service : https://lync.cherry.loc/ucwa/v1/applications
Internal Webscheduler service : https://lync.cherry.loc/Scheduler
External Webscheduler service : https://lync.cherry.loc/Scheduler
Total server discovery time: 5,0 seconds
Server discovery succeeded for secure (HTTPS) external channel against URL https://lyncdiscover.extdomain.ru/
Starting automatic discovery for unsecure (HTTP) external channel
Couldn't connect to URL http://lyncdiscover.extdomain.ru/[email protected] (HTTP status code NotAcceptable)
Server discovery failed for unsecured external channel against http://lyncdiscover.extdomain.ru/
Starting the requirement tests for Lync Mobile 2013 App
Please wait; this test may take several minutes to complete...
Testing the app requirements using the following discovery response:
Access Location : Internal
SIP Server Internal Access : lync.cherry.loc
SIP Server External Access : sip.extdomain.ru
SIP Client Internal Access : lync.cherry.loc
SIP Client External Access : sip.extdomain.ru
Internal Auth broker service : https://lync.cherry.loc/Reach/sip.svc
External Auth broker service : https://lync.cherry.loc/Reach/sip.svc
Internal Auto discover service : https://lync.cherry.loc/Autodiscover/AutodiscoverService.svc/root
Internal MCX service : https://lync.cherry.loc/Mcx/McxService.svc
External MCX service : https://lync.cherry.loc/Mcx/McxService.svc
Internal UCWA service : https://lync.cherry.loc/ucwa/v1/applications
External UCWA service : https://lync.cherry.loc/ucwa/v1/applications
Internal Webscheduler service : https://lync.cherry.loc/Scheduler
External Webscheduler service : https://lync.cherry.loc/Scheduler
Starting tests for Mobility (UCWA) service
Verifying internal Ucwa service: https://lync.cherry.loc/ucwa/v1/applications
Successfully created the UCWA service
Completed tests for Mobility (UCWA) service
Verification failed for Mobility (UCWA) service. The service could not be reached from an external network.
Select All results above for more information about the failures. Detailed information can also be found in the log file.
Your deployment meets the minimum requirements for Lync Mobile 2013 App. -
No contacts in Lync 2013 client and not appearing in others contact lists
Hello all,
I hope someone might be able to help out with this problem, I've been at it for weeks with no luck. I've migrated from Lync 2010 to 2013. All users have been successfully migrated and everything is working for them, except for one user (which i me unfortunately).
When I sign into Lync from any device (desktop, laptop, windows phone, iphone) I do not see any contacts in my organization, but I can find any of the contacts if i search for them. I also don't appear in anyone else's contact list, but they can find me if
they search.
I have tried disabling and removing my account from Lync server, uninstalling and reinstalling the Lync client on my machine, cleaning up all the Lync folders and registry keys on my machine. Nothing seems to get me any closer to getting this fixed.
I did find a discussion
here that is exactly the problem I'm having, but I don'e see a solution there either.
Has anyone else seen this before? Any suggestions or ideas would be very appreciated.
Thanks in advance!I am afraid your Lync account lose the user data contact list when you move user from Lync Server 2010 to Lync Server 2013.
Please try to move the user back to Lync server 2010 to check if the contact list is stored.
You can use the tool DBIMPEXP.exe to back up specific user’ data from Lync Server 2010 and import the data to Lync Server 2013 with the command Import-CSUserData which is introduced in Lync Server 2013.
Before you import the data, you need to use the command Convert-CSUserData to convert exported user data to the data format used by Microsoft Lync Server 2013.
For the details, please check
http://www.shudnow.net/2012/10/09/dbimpexp-exe-functionality-integrated-into-lync-2013-preview-management-shell/
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information
found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Lisa Zheng
TechNet Community Support -
Exch 2013 Installation and configuration from a SBS point of view?
I was just wondering if anyone has stumbled upon any good "how-to" sites for those of us that (up to now) have been used to using SBS servers but now find ourselves needing to go the manual route with separate new servers (domain controller and
Exchange 2013 server)?
I'm trudging along with my first Server 2012 R2 and Exchange 2013 SP1 installation and configuration, but since I'm used to things configuring themselves in SBS, the piecemeal approach to 2013 is presenting challenges for me.
Considering the market for SBS is small business (and for me, typical 20 users), I'm looking for some direction and help in configuring these new servers to act like SBS 2011 replacement servers, with similar capabilites, etc...from the viewpoint of an SBS
administrator, per se.
Maybe nothing exists and we have to start from scratch, but I was hoping with as big as the SBS market was, there would be some useful info out there with the realization that we're coming from SBS.
Thanks.Hello,
It seems you have installed the Exchange Server and preparing to move mailboxes to the new host. You can check the application log to check whether the new installed Exchange works
fine.
If there are any error ID/reports, you can post them here for our referernce.
Thanks,
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Simon Wu
TechNet Community Support
Maybe you are looking for
-
Lync login error use self account without delete cache , but can login with others account anyway
Greetings I deployed Lync Server 2010 for my customer. it's running well for about one year. but there are some users cannot login on lync these days. we tested the issue, the following is the test details: - only about 20% users cannot login on l
-
Error Downloading Music to Network Drive
I've moved my Music Library to a networked drive (NTFS) on a Windows XP system. The workstation that I'm running iTunes on is also Windows XP. Since then I cannot download purchased MUSIC (haven't tried videos yet). After initiating download via eith
-
When saving a document as a PDF, the text converts to symbols. How do I correct this problem?
English word text in a document that is saved as a PDF appears in the PDF as a series of unreadable symbols, letters, and numbers. This happens in Adobe Acrobat 9 and X Pro.
-
Creating links to Word, PDF and Powerpoint files
I need advice on how to create links to Word, Powerpoint and PDF files in my Captivate project. How do I also make sure that when my file is published, those links can be accessed by the reader. I am new to this process. Thanks!
-
My app tabs won't survive a restart. Must I re-pin them with each new session?
I like app tabs. But for some reason, mine disappear each time I restart. Is this how they're supposed to work? Is there something I need to do to save them? Or am I doing something wrong? I have an Intel iMac running OS X 10.6.7.