M-Audio 61ES not playing nicely with Logic Pro X!

The 61ES has been doing some really wacky things: I opened it up out of the box for the first time last night and right off the bat the middle octave of notes on the controller were very quiet compared to the high and low notes on the board. It was like the velocity wasn't working properly on those keys or something. The sounds worked fine in Logic when I pencilled them in. But I was too tired to mess around with it more, so went to bed and figured I'd deal with it in the morning. So this morning, the middle octave of keys seems fine, but the middle G just won't play at all. And many of the notes aren't tracking, or playing- especially during fast passages.
I pulled up Pro Tools 10 and the 61ES worked fine. So something is going on between the controller and Logic. Anyone have any ideas?
I'm running it on a MacBook Pro with 10.8.5. And the latest version of Logic Pro X- 10.0.6. Thanks for any advice!

Try this....
http://www.noterepeat.com/products/m-audio/usb-midi-controllers/axiom-air-series /269-m-audio-axiom-air-series-setup-with-logic-pro-x
Also make sure you have installed the latest drivers for the Air and Logic...
Axiom AIR Mini 32 Hyper Control Logic v1.0.2 (Mac)
Other that that.. Id contact M-Audio support for further help and advice
http://www.m-audio.com/support

Similar Messages

  • Logic remote of my iPad is not connecting anymore with Logic Pro X of my i Mac

    Logic remote of my iPad is not connecting anymore with Logic Pro X of my i Mac.
    Pls help
    tks
    Kind Regards
    Richard Garrell
    Belo Horizonte
    Brazil

    Hi Richard Gl , 
    Welcome to the Apple Support Community!
    I understand that your Logic Remote is not connecting. In this situation I suggest reading over the attached information and making sure that Logic Remote is set up correctly. I would also suggest trying to connect using Wi-Fi and Bluetooth.
    Logic Remote for iPad: Get started
    Cheers,
    Joe

  • USB audio fault using vrm box with Logic pro X

    Hello,
    Having problems with audio output from both usb ports on my Macbook Pro - I have a VRM box connected to the usb port and sound is coming from the left side of my headphones only.  Any help / advice with this much Appreciated.
    Ian

    I'm afraid you have quite a learning curve ahead of you.
    MIDI is not audio, the MIDI tracks you record are not sound, they are little tiny bits of data that tells what key note was presses and how fast (velocity) you played it. The data you're recording will play any sound on any MIDI Instrument. To get the sound of the MOX8 -IN- Logic you would have to record the audio outputs of the MOX8 into Logic as an audio track.
    As with most Workstations you can set up a "Performance" mode that has different instruments on separate MIDI channels, this is for use with the Internal MOX8 sequencer but can also be used by an external sequencer like Logic. For instance, you could have different instruments on MIDI Channels 1 thru 9 and a drum set on channel 10, In Logic you could have ten tracks set to the MIDI channels you want to play on the MOX8... however, the sound would not be in Logic, the sound comes from within the MOX8. To actually get the sound in Logic you have to record it as an audio track. There are other more advanced methods but that's enough to think about. You will need to the Yamaha MOX8 manual and figure out how to set up a performance mode. 

  • Core Audio Drivers not Found Error (no Logic Pro Installed)

    I am receiving the following error in GarageBand 08 and was hoping someone might be able to assist.
    When recording with a USB mic in GarageBand 08 (MXL USB.006) I sometimes get the following error: (Core Audio Drivers not Found). The error occurs after I have completed a recording session and removed the USB mic. (The error occurs regardless of if I close GB before removing the mic; but only occasionally)
    In checking the GB preferences, the Built-In audio option has disappeared from the drop down menu entirely for both Audio Input and Audio Output (although it still can find the USB mic if I reattach). In the Utilities folder, audio preferences, the Built-In audio option is also missing from the drop downs. (Not grayed out -- missing).
    In researching the problem, it looks like a similar problem occurs with the Logic Pro suite but I don't have that installed on my Mac (and never have). In contacting MXL support, they noted that it was a problem with Leopard and they didn't have a fix.
    At this point, I'm looking for either (1) a fix I've missed in my research or (2) an easy way to reinstall/replace/find the drivers without having to restore my system from backup. I've received the error three times now and restoring from back up - which clears the error and restores the drop down - is getting tiresome.
    Thank you!

    Thank you for the suggestion! I believe that was the issue the first time I lost the drivers. Unfortunately, even resetting the inputs and closing GB before disconnecting doesn't guarantee my Built-In audio won't disappear. Thank you for trying though!

  • Audio Instr records but does not play back in Logic Pro 9

    Hi all.... recently upgraded from a PPC G5 to an iMac 27"" 2.8 GHz Intel i7 w/4GB mem. was running Logic 7.2,now Pro 9. Here's my prob. After opening an old session in LP9 and recording an audio instrmnt (no prob setting up trk or recording) the trk won't play back. However,I was able to drag the recorded region to another trk (set up w/same audio instrmnt) and it plays.Is there some possibility that when opening a Logic 7.2 session that LP9 sees an audio instrmnr trk as an "audio"trk instead? Since I'm relatively new please excuse any newbie faults. Any help is greatly appreciated.
    -Ronnie-

    Hi all.... recently upgraded from a PPC G5 to an iMac 27"" 2.8 GHz Intel i7 w/4GB mem. was running Logic 7.2,now Pro 9. Here's my prob. After opening an old session in LP9 and recording an audio instrmnt (no prob setting up trk or recording) the trk won't play back. However,I was able to drag the recorded region to another trk (set up w/same audio instrmnt) and it plays.Is there some possibility that when opening a Logic 7.2 session that LP9 sees an audio instrmnr trk as an "audio"trk instead? Since I'm relatively new please excuse any newbie faults. Any help is greatly appreciated.
    -Ronnie-

  • Flash not playing nicely with IE favorites bar

    I administer a website (
    http://womenscenter.uconn.edu/new_site/
    ) which on its main page has a Flash movie looping. It also has a
    left menu bar for navigation, and everything is blissful until one
    turns on the favorites bar in Internet Explorer. Then if the screen
    is not big enough, the navigation bar is actually cut off in favor
    of the Flash movie. What this means is that if there isn't enough
    space with the favorites bar for both the navigation bar and the
    movie, the navigation bar loses out rather than the other way
    around (which is what one expects and wants to happen). I know it's
    the Flash movie causing this because it doesn't happen on any of
    the other pages in the site, which are basically identical in
    layout except they don't have the Flash. Any help in preserving the
    navigation bar would be greatly appreciated!

    You can try to disable the hardware acceleration in the Flash Player.
    See [[Cannot view full screen Flash videos]]
    * http://www.youtube.com/swf_test.html (right-click the player: Settings)
    Flash "Display settings" window:
    * http://www.macromedia.com/support/documentation/en/flashplayer/help/help01.html
    Your above posted system details show outdated plugin(s) with known security and stability risks that you should update.
    *Shockwave Flash 10.2 r153
    * http://www.mozilla.com/plugincheck/
    Update the [[Managing the Flash plugin|Flash]] plugin to the latest version.
    *http://kb.mozillazine.org/Flash
    *http://www.adobe.com/software/flash/about/

  • Time Capsule does not play nicely with Cisco Router

    Three days ago, I had an older Linksys router attached to our ISP's cable modem by ethernet; the network included a wireless time capsule and apple express base station set up by our son last year (who understands this stuff, but lives 2,000 miles distant).  The router died and I purchased a new Linksys router (E2500).  It is occupying the same spot as the old router, but running with no security settings as yet.  My wife's iMac and two Windows XP laptops work just fine on the network, as well as our NetFlix connection on our TV.  My MacPro, however, can not access the main network - it can see it but won't grab an IP address.  It will, however, see and connect to the router's guest account, although with reduced signal strength.  The Time Capsule is now connected to the MacPro by ethernet (if I make it wireless, it will back up fine, but I can't access Internet or send email on the guest account).  The AirPort Express is unplugged and not a factor.
    Yesterday, I spent most of the day on the phone with Cisco (who claimed AirPort Express will not work with their routers, which I know to be, um, less than accurate), and with Apple Support - who did not help (other than to set up a Genius Bar appointment this morning at the local Apple Store).  The Genius Bar turned out to be a disappointment as well - the MacPro with Time Capsule attached worked perfectly on the main network in the store, but at home, even with a test user account with Admin authority, as they suggested), no go.
    If I unpower Time Capsule, I loose Internet.  With Time Capsule plugged in, I can access my router's guest account -
    Aside from returning this router and starting fresh with a different brand router, any suggestions?
    Thanks for any guidance, suggestions, etc.

    My first reaction is to suggest you ring your son.. !!
    And I guess my second one, would be to remove the E2500, and connect the time capsule directly to the cable modem.. they are equivalent devices. The TC is an excellent wireless router and will work better as the primary router in your network. Turn off the cable modem so it can pick up the new device.. plug the TC directly to the cable modem then turn on both.
    Make sure the TC is working as router.. and you should be able to setup the wireless to connect all your computers etc.
    The E2500 can also be used as a WAP if you need more range. But be aware you have to make sure it uses a separate channel to the TC. Plug it in via ethernet to LAN port not WAN.. and turn off dhcp and set the IP to same IP range as the TC but make it outside the dhcp scope. So for example the TC is running 10.0.1.1 and then make the E2500 10.0.1.254
    The express cannot do WDS to the Linksys.. so what you were told is correct. It may be able to connect via ethernet but not as repeater. But you can do that with the TC now that it is the main router.

  • Spry accordion widget not playing nicely with IE7

    Good day.
    The answer to this issue may be on this forum somewhere already, but I cannot take the time to scour the several hundreds of posts.
    I've build and customized my first spry accordion, which can be viewed at http://www.brianfisherart.com/Bio/Contact/
    In Firefox and Safari, it works perfectly! IE7 however has some issues. the panels get too large on mouseovers, and jumpy and even larger when opening lower level panels.
    Just hoping to find a quick fix.
    Thanx in advance.

    I'm certainly not going to do your search for you, but you might want to see if using the current version 1.6.1 works better.
    http://labs.adobe.com/technologies/spry/
    If that doesn't work, you might want to go to the Spry forum.
    Of course, now that you've posted, I wonder if any of the links in that "More Like This" box apply?
    Mark A. Boyd
    Keep-On-Learnin' :-)
    If you are reading this via email, be aware that it may not be an accurate representation of my message. Login to read the actual message and/or to reply.

  • Using Mackie Control with Logic Pro 7 and Yamaha O1X

    I currently own a Yamaha O1x which is a mixer/control surface/audio interface that I use with Logic Pro 7. I am planning on selling the O1X and replacing it with the Mackie Control Universal as my DAW controller and using the Apogee Ensemble as my audio interface. I already have purchased the Mackie Control Universal and would like to begin using it instead of the O1X as my DAW controller, but while I am waiting for the Apogee Ensemble to be released I still need the audio interface capabilties of the O1X. The O1X uses Yamaha's MLAN protocol to connect to the G5. MLAN is a firewire interface that can transmit both audio and midi. Does anyone have a suggestion for a work-around solution so that I can use my Mackie Control Universal (which connects via midi cable) and only use the audio capability but not the control surface of the O1X via the firewire connection? I haven't been able to figure my way through this one and see if it is possible. I have already tried having them both hooked up at the same time, and the Mackie Control seemed to work fine but the audio on the O1X didn't seem to be connecting and functioning properly. I appreciate any help as I am anxious to use my Mackie Control.
    Thank you!

    You need to connect only the Audio and not the MIDI between your 01x and Mac. You can achieve this in mLan Graphic Patchbay-connect the cables between the Nodes in Audio part of a Graphic Patchbay, connect the Wordclock but do not make any MIDI connections. this way it should work as you want. the other way is to Make your regular connection from mLan Autoconnector and disable the MIDI ports that are dedicated to control the DAW by 01x by some freeware utility (01x uses port 1 for that...)
    As this is quite 01x specific, please visit 01xray.com/forums where you will find more help, or send me PM.
    As Apogee enssemble is expected to have great features, I would rather recommend the i88x instead of Enssemble (i88x has two Mic preamps-the best Yamaha produces (derived from Dm2000)VERY good converters (mLan is known for low jitter and it was tested with Rosseta by a mate from 01x forum who said (he tested it in store with other people) that i88x sounded better-may believe it or not...).The mLan Graphis Patchbay application allows you to patch connections between mLan devices and computer -very flexible. 01x already does almost the same as Mackie control and it is for almost the same price.... But maybe you are pi_ssed of waiting for new mLan drivers? I am just speculating....

  • I am recording with Logic Pro X, using my Yamaha XS8 keyboard as a Midi controller. I also have a Thunderbolt Display. Every time I play and release a note on the keyboard, the Thunderbolt Display speaker emits a doink sound. How do I get it to stop?

    I am recording with Logic Pro X, using my Yamaha XS8 keyboard as a Midi controller. I also have a Thunderbolt Display. Every time I play and release a note on the keyboard, the Thunderbolt Display speaker emits a doink sound. What is causing it and how do I get it to stop? My sound is running through the Saffire Pro 40 Interface (Focusrite) into external speakers with powered amps.
    Also, When I record I am hearing little pops in the system. I have checked all of my meters and they are not clipping. What is causing it and how do I get it to stop?
    Ken

    MUYconfundido wrote:
    Pancenter,
    Thanks for the response, but I do not have a midi interface. I am using a midi to usb connector cable, thus bypassing the need for a Midi interface.
    The Mac reads the USB cable as a midi device, but not the keyboard that I am trying to use as a controller. I have tried it with my korg sp 300 and with my Nord Electro 2.
    Thoughts?
    Thanks,
    Tristan
    Tristan...
    This is what you have, correct?
    http://www.alesis.com/usbmidicable
    This from Alesis..
    "The AudioLink Series USB cable receives and outputs MIDI signal thanks to its internal interface. The USB-MIDI Cable connects plug-and-play to your Mac or PC for an all-in-one USB-MIDI solution."
    Notice, -internal interface-. What you have is a simple USB MIDI Interface. Most MIDI interfaces are USB.
    My point is (was), MIDI OUT of the Korg goes to the connector marked MIDI IN on the Alesis, those new to MIDI often get this wrong.
    pancenter-

  • I have created a PDF with mp3 audio clips, the file works on PC's with audio playback (WIndows 7, 8 ) however the audio does not play when hosted on a website or an ipad/tablet computer or smart phone when used with PDF reader

    I have created a PDF with mp3 audio clips, the file works on PC's with audio playback (WIndows 7, 8 ) however the audio does not play when hosted on a website or an ipad/tablet computer or smart phone when used with PDF reader

    adobe42135678 wrote:
    the audio does not play when hosted on a website...
    When viewing in what browser?

  • Which 61 key midi keyboards work with Logic Pro X (10)? M-Audio, Novation, Akai, Roland???

    Hi. I'm new to this community but would really appreciate some help.
    I'm struggling to find a 61 key midi keyboard which works properly with Logic Pro X.
    I was looking into getting either the M-Audio Axiom 61 or Novation Impulse 61 but all I can find on google etc. is people saying they don't work properly.
    Has anybody got a 61 key which works seamlessly with Pro X?
    Any help would be much appreciated.
    Thanks.

    To "The Art Of Sound"
    Hi. I doing next.
    1. I create new project
    2. I select Yamaha Grand Piano
    3. I play something in "live" mode. All is ok
    4. I play something in "Rec" mode. All is ok
    5. I record second track with the same instrument, with Yamaha Grand Piano. All is ok
    6. I record third track with Yamaha Grand Piano. All is ok again.
    7. Now I muting first or second track and... third track plays wrong notes! I unmute first track, but third track still to play wrong notes! Why???
    Ok. I continue experiment with created project. I have three Yamaha grand Piano tracks and I creating new software instrument and assing Hovering Machine to it. I try to play in "live" mode something. And I get interesting effect. If I play short notes (sixteens, for example), I can play for one minute without problem. And Logic Pro X starts to play wrong notes after this time delay.
    If I start to press chord notes without breaking, Logic  Pro X plays for 15-30 secounds normally and starts to play wrong notes them.
    Well. I turn off all plugins and effects from instruments. But Logic Pro X countinues to play wrong notes!
    I experimented with NI Kontakt 5. Kontakt plays wrong notes!
    I experimented with LUSH-101 plugin and minimoog. This two instruments play correct notes always!!! WHY????
    Why some instruments play wrong notes and other instruments play correct notes in the same project?
    I wrote wrong in my previous post. I got this problem with Logic Pro X 10.0.3 update.
    Actually I have serious problem now. I opened projects created in Logic Pro X early and I have this problem  in ALL projects. This's commercial projects and my partners asked me already about release date... What must I answer?

  • Using Acrobat 8, Embeded audios are not playing in browser.

    I have PDFs with embeded audio. But when load PDFs online and open in browser then AUDIO is not playing.

    Hi Piyush_Bajpai,
    Do you have flash player installed on the machine?
    Please use this link to download Flash Player -
    http://helpx.adobe.com/acrobat/kb/reader-acrobat-flash-player-download .html#main_download
    If the problem still persists, please help us undersrtand the problem by answering the below -
    1. Are there any errors when the content does not play ?
    2. What audio content type (file extension) are you trying to use ?
    3. Do you access PDF files (having audio/video) from an http url  ?
    4. Could you please provide one such sample file to help me replicate ?

  • Edge animate cc Audio does not play on mobile phones & iPod though it plays perfectly on an mac pro

    I have uploaded an edge animate cc published html with sound. The html file opens perfectly on my mac pro safari browser perfectly with audio. But when I open the same file on my iphone5 the file opens but no the audio does not play. What wrong does anybody have an answer?

    You are right. But there detail. If Online audio will be downloaded to this user interaction. Depending on your animation will all be out of sync with the audio. For the timeline will run before. I do not know how to do but needed to put a stop to that timeline only run when the audio is downloaded. I had problems in IOS and Android with audio using adobe edge previous version before they even have audio support. Used Edgehero who answered my expectations very well. Only had this same problem but it was solved this way.
    Here's a link http://www.edgehero.com/ForumRetrieve.aspx?ForumID=94&TopicID=14286&NoTemplate=False

  • USB Interface Not Working With Logic Pro 9

    Hello,
    I've had a Tascam US-1641 for several years now with absolutely zero issues on my old PC. Ever since I upgraded to Mac (early 2011 17 inch Macbook Pro running Snow Leopard) I've had nothing but problems with the US-1641. No matter how many times I uninstall-reinstall the drivers and what USB port I plug it into, whenever I turn on the device and it's connected to my Macbook, it crashes my operating system and it freezes everything I was doing. Logic Pro doesn't load and when it sometimes does (10 minutes later), it immediately crashes when I click anything.
    I've tried several tips to fix it and nothing worked. The most popular choice was select the default input/output in Logic to the system audio, then quit Logic, turn on the interface, then restart Logic. No such luck. I have to reboot my machine at least 5 times, uninstall/reinstall the driver and hope it works to use the interface. I thought it was the operating system, so I upgraded to Mountain Lion and installed the new driver for Mountain Lion, after of course deleting the other drivers and removing all previous data, and it is still giving me the same problems.
    I don't have the money to afford a replacement model or a different interface from a different company, so I'm hoping you guys can help me figure out what exactly it is that's causing the interface to freeze my operating system and crashing my Mac whenever I try to use it. I am getting extremely frustrated at this and as much as I love OSX and Logic, what good is this piece of software if I can't use it? I need help.
    Thank you.

    The problem lies with Tascam and their inability to write stable drivers for OS X...  and isn't anything to do with Logic Pro ..
    As you know, you are not the only person to have had this issue and the reality is, while the 1641 might work fine with  Windows, when it comes to OS X Macs.. it's an entirely different story... depending on the version of OS XS you are running.
    The one tip I have read, that seemed to fix it for most people.. (Though not all) is as follows;
    (Thanks to Paulypaulpaul for this)
    -uninstall your tascam driver 2.10
    -restart
    -install driver 1.03
    -restart
    -plug in your tascam
    -goto where you download your drivers (http://tascam.com/product/us-1641/downloads/), scroll down to the bottom where it says firmware, Download the firmware 1.02 (3rd from top under firmware), install it. your control panal should now read 1.03 for your drivers and 1.02 for your firmware.
    -install drivers 2.10
    -restart
    Follow each of the steps exactly.. including all restarts when indicated..
    ...and good luck...

Maybe you are looking for